ADDITION/ ALTERATION TO SMALL ARMS WORKSHOP (BLDG NO. P-10) AND PROVISION OF ADDITIONAL STATIC WATER TANK OF 50 KL CAPACITY NEAR FIRE STATION AT NAD KARWAR.

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for foundation and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m depth for foundation and getting out in soft/ loose soil for laying/ taking out GI pipe line complete all as specified and directed.

Excavation not exceeding 1.5 m deep and getting out in hard/dense soil all as specified and directed.

Excavation exceeding 1.5 m deep but not exceeding 3.0 m deep and getting out in hard/dense soil all as specified and directed.

M & L for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation & filling in mass concrete complete all as specified and directed.

M & L for plain cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M & L for hardcore of broken stone or boulders of gauge not exc 63 mm and deposited, spread and levelled in layers not exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in harde/dense soil complete all as specified and directed.

Removing excavated material hard dense soil exc 50 m but not exc 100 m depositing where directed at a level not exc 1.5 m above the starting level complete all as specified and directed.

M & L for cement concrete 100 mm thick type B-2 1:2:4 (using 20 mm graded aggregate) as in floors complete all as specified and directed.

M & L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description exc 10 cm in width or girth complete all as specified and directed.

S & F steel work in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 complete all as specified and directed by Engr-in-Charge.

S & F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates (Fe 410 W Gde- E-250) Quality A, complete all as directed by Engr-in-Charge.

S & F Glass dividing strips, 3 mm thick of 38 mm width and inserted in position to conform design complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 MPa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

M & L for RCC design mix M30 as in foundations including rafts, footings, foundation beams, plinth beams bases for columns etc basement slabs, under reamed piles & mass concrete complete all as specified and directed.

M & L for RCC design mix M 30 for Walls, retaining walls of any thickness using 20 mm graded stone aggregates complete all as specified & directed.

M & L for RCC design mix M30 using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings etc complete all as specified and directed.

M & L for Formwork to sides of concrete foundation, footings bases of columns, raft & raft beams & soffit of foundations & plinth beams & similar work fair finished of curved shape complete all as specified and directed.

M & L for Formwork to faces of walls, retaining walls etc fair finished of curved surfaces all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work exceeding 200 mm thick fair finished complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

M & L for rendering 15 mm thick in two layers (10 mm + 5 mm) in CM 1:4 on fair faces of concrete surfaces finished even & smooth without using extra cement all as specified and directed.

M & L for rendering 15 mm thick in CM 1:6 on fair faces of concrete surfaces finished even & smooth without using extra cement all as specified and directed.

Supply only Integral water proofing compound as specified and diretced.

S & F cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop value boxes, gate stops, parts of ranges and similar articles complete all as specified & directed.

M & L for 100 mm thick plain cement concrete, type C-2, (1:3:6) using 40 mm graded aggregate as in sub base/plinth protection all as specified and directed.

M & L for three coats of white wash on wall all as specified and directed.

M & L for two coats of distempering walls with distemper dry, white on wall all as specified and directed.

S & F 50 mm outer dia, 3 layer PP-R (Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stabilised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete and laid in trenches including testing complete all as specified and directed by Engr-in-Charge.

S & F PPR gate valves (Brass insert) of size 50 mm bore including testing complete all as specified and directed.

M & L for making connection of PP-R distribution branch with PP-R main of sizes 50 mm dia by providing and fixing Tee of size 50 mm x 50 mm x 50 mm including cutting and making fusion joint etc complete all as specified and directed.

S & F LED flood light luminaire 200 Watt with secondary optics made in pressure die cast housing and heat sink in aluminium extruction with IP66 protection complete all as specified and directed. MAKE: Bajaj Cat Part No. BARFEG 200W LED or equivalent in Philips/ C&S/ Havells

S M Shetty

Bidder Name

sohan construction

S M Shetty