Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹23.6 LAccepted-AOC SCO 10 BLOCK NO 2 SDA COMPLEX KASUMPTI SHIMLA 09 | SHIMLA | HIMACHAL PRADESH | 171009 | L1 | Accepted-AOC Being L1 | |
| 2 | L2₹23.7 L+₹12,143 (0.51%)Rejected-Finance HARI OM BHAWAN CIRCULAR ROAD UPPER KAITHU SHIMLA | L2 | Rejected-Finance Being L2 | |
| 3 | L3₹23.9 L+₹25,281 (1.07%)Rejected-Finance | L3 | Rejected-Finance Being L3 |
Tender Value
₹21.5 L
EMD Value
₹40,000
Closing Date
24 Nov 2020, 5:00 pmClosed
XEN Elect Division No II HPPWD Shimla-2
XEN Elect Division No II HPPWD Shimla-2
Extension of central heating
2020_PWD_42217_1
ED.II.GA.Tender/20-21-6436-37 dated 03.11.2020
Open Tender
Electrical Works
Item Rate
180 days
Shimla
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
EE Electrical Division No II
₹40,000
18 Jun 2021
10 Nov 2020
25 Nov 2020
10 Nov 2020
24 Nov 2020
10 Nov 2020
Amount
Supplying, installation, testing & commissioning of compact type, Histatic Hiwall mounted power coated Hot water Fancy Forced air radiator Unit of following capacity free air discharge capacity complete with fan blower suitable for operation on single phase 230V 50 Hz AC supply complete with finned hot water finned coil, air filter washable complete with thermostate modulating valve / 3/4 brass ball valve with strainer on inlet and 3/4" brass ball valve on outlet complete as required. (Make:- Airef, Ventair, Rapidcool, modren engineering or any other approved by the Engineer-in-Charge.)
12000 BTUH / 3000 KCAL
18000BTUH / 4500 KCAL
Supply, installation, testing and commissioning of hot water piping and fittings complete with supports, hangers and specified insulation thickness. All piping shall be black mild steel class C, ISI marked with fitting. The unit rate of piping shall include this support arrangement and hangers including wooden saddles where required under insulation at support points. The piping shall be insulated with 80kg / M.Cub section density, fiberglass insulation finally covered with 26 gauge Al. cladding for outside and 6 mm plaster for inside complete as required. Make:- Tata, Jindal or any other approved by the Engineer-in-Charge.
100 mm pipe with 100 mm insulation
80 mm pipe with 75 mm insulation
62 mm pipe with 75 mm insulation
50 mm pipe with 75 mm insulation
25 mm pipe with 50 mm insulation
19 mm pipe with 50 mm insulation
Supply, installation, testing and commissioning of Gate Valves / Sluice valves ISI marked with flanges or screwed ends as required. Valves 65 mm and above shall of cole body with flanged ends and gunmetal trim, non-rising spindles, P.N. 1.6 and including flanges where required and valves upto 50mm shall be gunmetal non-rising stem, integral seat, body test pressure 50 kgf / cm Hyd. (Make:- Kriloskar, Sant, Leader or any other approved by the Engineer-in-Charge.)
KHARBANDA ELECTRICALS
Comfort technologies
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.PDF
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .