SPECIAL REPAIR TO BLOCK NO. P 22 (12XQTR) AT MIL STN PATIALA UNDER GE (SOUTH) PATIALA

Amount

Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed by Engr-in-Charge.

M&L for cement plastering 10mm thick in cemet mortar 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for cement plastering 15mm thick in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished Fair and even without using extra cement and with or without fixing of chicken wire gauge where directed complete all as specified and directed by Engr-in-Charge. Note : WPC and chicken wire gauge will be measured and paid separately.

Supply only integral liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

Supply only chicken wire mesh 22 gauge of size not less than 20X20mm complete all as specified and directed by Engr-in-Charge.

M&L for cement plastering 5mm thick in cemet mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projections etc with mechanical means/grinder complete all as specified and directed by Engr-in-Charge.

M&L for applying acrylic thick wall care putty on internal/external surfaces of walls/ceilings/soffits (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving painting etc complete all as specified and directed by Engr-in-Charge. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further finishes. Please note that the further finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good to disturbed surfaces complete incl reqd shape for hold fast block for new frame complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good to disturbed surfaces reqd shape for hold fast block for new frame complete all as specified and directed by Engr-in-Charge.

S&F Spray Docu painted Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc., complete all as specified, size 105 x 60mm and incl cutting holes and making good disturbed surfaces reqd shape for hold fast block for new frame incl cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in holdfast blocks/ filling in chowkats complete all as specified and directed by Engr-in-Charge.

S&F Spray Docu painted Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc., complete all as specified, size 125 x 60mm and incl cutting holes and making good disturbed surfaces reqd shape for hold fast block for new frameincl cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in holdfast blocks/ filling in chowkats complete all as specified and directed by Engr-in-Charge.

S&F factory made flush shutters 35mm thick minimum 5 ply, solid core construction, with block board core and plywood face panels, commercial type on both sides with 6mm thick lipping frame to match complete all as specified and directed by Engr-in-Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge. including stainless steel 304 Grade wire cloth (wire dia. 0.36mm) and the supply and fixing following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fixing factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid PVC foam sheet , reinforced with steel square tube , complete all as specified and directed.

S&F Factory Made Solid penal PVC Door Shutter 30mm thick (style) consisting of frame made out of ms tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC C chennal having a PVC sheet strip of 20mm width stuck inside with solvent cement forstiles and plain colour PVC sheet for top rail,lock rail& bottom rail on either side and as gap inseerted for top rail and bottom rail .penelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVXC sheet beading ,and joined together with solvent cement ,supplying and fixing in the frame at sites as per specification and dwg as specified. including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing factory made extruded aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf and incl hook and eye. Note: complete shutter window will be treated as single uit and paid as single unit

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

M & L for preparing new wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

Dismantling, floor, hearth or wall tiling including CM(bedding (but not backing), removing serviceable tiles to store & rubbish off the premises

Non skid ceramic joint free (with rectified edges), Non Skid/ Matt superior finish grade B-II (a), floor tiles 7-8mm thick and area exceeding 0.11 sqm but not exceeding 0.18 sqm, coloured as in flooring etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tile including 15mm thick screed layer in CM 1:4 over and including 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate finished fair and even complete all as specified.

Providing and Laying Premium (1st) quality digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish with flexural strength greater than 16 N/mm2, scratch hardness on Moh’s Scale minimum 3 and crazing resistance of 2 cycles in coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.

M&L Black colour Granite 16-20 mm thick (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like including 10 mm thick rendering in CM (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including rounding, molding and polishing on edges complete

M&L for machine cut kota stone slab as in flooring of size 580 x 580 mm each & 18-20 mm thick, set and jointed in cement slurry including border of 100mm wide baroda green/white mable as per pattern approved over & including screed of 20-22 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained. 2. The colour of the slabs shall be uniform.

M&L for machine cut kota stone slab as in skirting of 18-20 mm thick, set and jointed in cement slurry over & including screed of 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type polishing complete all as specified .

S&F vitreous china premium/1st quality wall hung wash basin half pedestal, white, flat back, min. size 500x400 mm , screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling half thread incl pvc pipe 40mm upto floor trap incl pvc connection ,and angle cock and also incl CP brass wash basin mixer and complete in all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.

S&F vitreous china premium/1st quality wash down water closet pan (pedestal pattern/EWC) S/P trap white colour of size 520X360X390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe and incl. S&F plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including and taking down existing of any description/size complete in all respect all as specified.

S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, white colour, valveless syphonic action type, , low level, with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

S&F PTMT Jet Spray with 1.5 metre long flexible tube including making connections and fixed in position complete in all respect as specified.

S&F 6mm thick looking mirror beveled edge fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish, etc.complete fixed in position all as specified and directed.

S&F PTMT 450mm long shelf for wash basin. Fixed in position complete in all respect all as specified.

S&F sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.

S&F overhead shower 120mm dia with 225-230mm long brass shower arm with wall flange and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified.

S&F Bib taps, CP, fency type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete in all respect all as specified.

S&F central hole brass chromium plated basin mixer with regular spout with/without popup waste system with 450 mm long braided hoses complete.

M&L for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, non telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and directed.

S&F Sink Cock wall mounted with swinging spout and with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed.

S&F Concealed Stop Cock, fancy type, CP with long shank and cup, exposed part kit with wall flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete in all respect all as specified.

S&F Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified.

S&F stainless steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling/round strainer of 110mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 914mm x460X203mm with bowl size 405x 354x203 and making good disturbed portion in CM 1:3 or PCC 1:2:4 as directed.

S&F towel rod CP 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and complete fixed in position complete all as specified.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as directed and specified.

S&F cockroach trap gratings AISI-304 of size 150X150mm square in shape with 5mm border complete in all respect all as specified.

Taking up or down existing steel tubing and connections, 15mm bore complete all as directed and specified.

S&F 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as directed and specified.

Taking up or down existing steel tubing and connections, 20mm bore complete all as directed and specified.

S&F 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as directed and specified.

Refixing 20mm bore GI steel water tubing medium grade fixed to walls complete all as specified.

Taking down of PVC water srorage tank of of 300 to 500 ltrs capacity as located on terrace of the building all as specified and directed.

S&F ISI marked doubled layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top / cover) 500 Ltrs capacity hoisted and fixed in position all as specified including 20 mm dia brass float valves, high pressure, with polythene float and fly nut complete screwed for 20mm bore iron pipe and including GI nipple/union of 20mm bore to connect GI tubing to PVC water tank complete all as specified and directed.

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified.

Plain cement concrete 1:7:12 mix, type E-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:3 , mixed with water proofing compound, on brick or concrete surfaces of wall of sunken portion, trowelled to even and smooth finish without using extra cement with WPC paid and measered sepretly complete all as specified.

Applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 200 micron thick polythene film over 85/25 grade bitumen layer @ 0.5 kg /Sqm all as specified

Providing 25 mm dia GI pipe medium grade spouts 60 cm long complete all as specified and directed.

S&F for MS Clamps, Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay) and similar small articles conforming to Fe-290 Gde-E-165 all as specified

PVC(HDPE) SWR , 40 mm bore, single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction,including all fitting elbow, tees, sockets, bends etc. laid in walls & floors for connecting bottle traps & nahani trap complete all as specified.

M&L cast iron multifloor/floor/nahani trap 100 mm dia and 450 to 600 mm long including jointing with solvent cement in repair complete all as specified and directed.

S&F Cast iron soil, waste and vent pipe,100mm bore, sand cast in any length, with or without ears, with lead joints, fixed to walls with and including stack clamps, nuts , bolts etc. and making necessary connections, fixed as in repair complete all as specified and directed.

Taking down of existing CI pipe 100 mm bore and refixing the same after cleaning painting with 2 coats in any position complete all as specified and directed.

S&F 100 mm cast iron soil waste and vent pipe in any length with or without ears laid in floor incl dismantling of old pipe and excavation of trenches, refilling and leveling of surface complete all as specified and directed.

Cast iron bends duck foot or heelrest, radius for 100 mm bore pipe, as in repairs, complete all as specified and directed.

S&F cast iron 4 way junction for 100mm bore with access door as in repair complete all as specified.

S&F cast iron junction combination 'T' equal or unequal for 100mm bore with access door as in repair complete all as specified.

S&F CI Bends (any radius), for 100mm bore CI piipes complete all as specified.

S&F 100mm bore Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified.

M&L for cast iron cowls of 100 mm dia complete all as specified and directed.

S&F CI gully traps, Centrifugal type 150 x 150mm size , square or roundmouthed, type 'P' or 'S' fixed in repair complete all as directed and specified.

Dismantling of brick tiles or terracing tiles single layers on roofs complete all as specified.

Demolition of mud phuska on roof any thickness all as directed.

Roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

PCC 1:3:6, type B-0 using 12.5mm graded stone aggregates as in padding over roof, minimum thickness at khurra as 25mm to maintain a slope of 1:100 ,complete all as specified and directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.

Providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength inlongitueinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

PCC plain factory made tiles ISI marked cement concrete tiles of size 250x250x20-22mm thick machine pressed set joined and pointed in neat cement slury in floor and cut and polished with grey cement and no pigment over 15mm thick cement mortar (1:3) bedding and joints grouted flish in cement mortar (1:3) mixed with integral water proofing compound over roof surface complete all as specified and as directed

M&L for dummy joints/construction joints 8mmx10mm as in PCC floors filled with polyurethane elastic adhesive/sealant (white/grey colour) of approx density 1.30kg/litre complete all as specified.

M&L for hardcore of beicks obtained from demolition/dismantling of brick work/brick tiles of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean raidus bulit in C:M 1:6 all as specified.

Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and smooth without using extra cement as in plinth protection including provision of construction joints and form work complete all as directed by Engr-in-Charge and complete as specified.

PCC 1:3:6 type C-2 using 40mm graded stone aggretgate, as in base for PVC tanks complete all as specified and directed.

Preparation of old steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified.

S&F 15-18 mm thick with min density 500 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S&F 15-18 mm thick with min density 500 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved color and other side plain white colour fixed with ss screws ans solvent cement/ adhesive to make kitchen cabinet shutters and shelves complete as per manufacturer’s instructions complete all as specified and directed.

S&F 5 mm thick with min density 500 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white colour and pasted with solvent cement/ adhesive on frame work of cup boards complete as per manufacturer’s instructions complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs

S&F tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished complete fixed in position all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified.

S&F Piano/continuous hinge of size 19 mm stainless steel complete all as specified.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required suze complete fixed in position all as specified.

S&F wardrobe tube/hanging rod for CB of size 30X15mm and 0.6mm thick stainless Steel 304 grade rectangular high gloss finish complete fixed in position incl S&F brackets/screws etc. all as per manufacturer's instructions all as specifie

S&F stainless steel finished locks (double action) with 2 nos of keys min outer body size 75mm suitable for wardrobes/CB etc. complete all as specified.

S&F Framed work such as grills, cooler stands gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

Preparation of surfaces (plastered or unplastered) of ceiling and M & L for applying three coats of lime white wash on ceiling surfaces etc., complete all as specified.

Preparation of Old/ new plastered or unplastered surfaces of walls etc., and M & L for applying two coat of distemper oil emulsion (OBD) over a coat of chalk whiting (as primer) complete all as specified and as directed.

Applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion complete all as specified and directed.

Taking down carefully existing points wiring on surface conduit/concealed conduit for light/ fan/socket /power/ bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, piece of wires,gutties, conduit, wooden boards etc and making good the disturbed portion of all floor, ceiling etc all as specified and directed.

M & L for point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan and including PVC rigid concealed conduit medium grade 19/20 mm dia to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed (Switches and regulators shall be measured and paid for separately.) ( Wiring shall be done as per colour code in IS for phase, neutral and earth) (In case of Modular: Modular cover plate and metal flush boxes incl in Point wiring) Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for earth.

All as per Sl item No 2 above herein before but one 5Amp socket point on independent board complete all as specified and directed.

All as per Sl item No 2 above herein before but one socket out let 5 pins 5 Amp on the same board but with other switches complete all as specified and directed.

All as per Sl item No 2 above herein before but one socket out let 3 pin 15 Amp Independent with 2.5 sqmm copper conductor (multi-stranded) PVC insulated electric cable 1100 volts (ISI Marked) including 2.5 sqmm PVC insulated and unsheathed FRLSH single core stranded copper as earth continuity conductor complete all as specified and directed.

M&L in replacement Modular switch 1 way, 6 Amps, 1 module complete all as specified.

M&L in replacement Modular Bell push switch 1 way, 6 Amps, 1 module complete all as specified.

M&L in replacement Modular switch 1 way, 16 Amps, 1 module complete all as specified.

M&L in replacement Modular socket 3/5 pin 6 Amps, 2 module with shutter complete all as specified.

M&L in replacement Modular socket 3 pin 6/16 Amps, combination type with shutter 2 module complete all as specified.

M&L in replacement fan regulator 4 step modular type 1 module, 100 W complete all as specified and directed.

M&L in replacement ceiling rose surface bakelite surface 65 x 50mm 3 terminals all as specified & directed.

M&L in replacement bell ding dong electronic complete all as specified and directed.

M&L in replacement Decorative angular Lamp holder, PVC polycarbonate type with LED bulb 9 W incl flexible wire 0.5 Sqmm copper cable for electric connection all as specified & directed.

Supply & fix in replacement of existing unserviceable batten fitting with LED batten fitting of 20W, 4 feet long of extruded thermoplastic body with PC diffuser, isolated body environmental friendly energy efficient including neccesary fitting on wall and making electric connection from ceiling rose to connector with suitable size of electric cable and making good the disturbed surface.

All as per Item No- 116.00 above but with LED batten fitting of 10W, 2 feet long all as specified and directed.

Supply and fix in replacement Surface Mounted LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver, IP54 inc connection with three core flexible wire 0.5 sqmm copper cable all as specified & directed.

S&F in replacement MCB DB double door 240 volts with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting type, drilling holes for incoming and out going cables complete suitable for 8 ways with IP54 protection complete all as specefied and directed. Note : i) Eye/bottle thimbles shall be used for connection in switches/sockets & MCB's in DB's without any extra cost ii) Electric rewiring should be done in proper colour coding i.e. Red for phase, Black for neutral and Green for earth

S&F in replacement MCB , SPN, 240 Volt ,32-40 amp for fixing in DBs of including proper thimble connections complete all as specified and directed.

S&F in replacement MCB, single pole 240 volts 6 to 32 Amp capacity fixing in DB’s including proper thimble connections complete all as specified and directed.

M&L in replacement for sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRls ,stranded copper conductor cable drawn in including PVC concealed conduit 25 mm dia incl 4.0 Sqmm PVC insulated unsheathed FR stranded copper conductor cable as earth wire all as specified and directed. Note- Necessary cutting chasing wherever required and making good the disturbed surface shall be part of job at no exact cost.

S & F in replacement energy saving and environmental friendly long life LED Bldg security light 35 Watt made up of pressure die cast alluminium housing with high power LEDs having top opening seperate driver compartment with IP65 protection and impact resistance of IK07, including all connecting acessories including 32 mm bore light grade GI pipe bend to shape including MS clamps of required size for fixing of Light on wall complete all as specified by Eng-in-Charge.

M&L in replacement Earthing complete with galvanised steel earth plate electrode, 600x600 x 6.0mm thick buried directly in ground(earth pit not less than 2.25m deep below normal level) connected to galvanised earth lead wire 4.0mm dia by means of nuts, bolts, & washers of GI as shown in electrical plate No 3 of SSR Part I. Connected to earthing test point testing complete including necessary earth pit chamber PCC 1: 3: 6 type C1, and 50mm thick RCC 1 : 2: 4 chamber cover and with 8mm dia mild steel re-enforcement of 15Cm C/C spacing both ways with a handle made of 8 mm bar for fitting, galvanised iron funnel, wire mash watering pipe GI 20 mm dia light grade, and protection to earth lead shall be provided with GI pipe light grade 15mm dia up to 7.5m from the earth plate electrode, excavation, retuning filling, Removal of surplus soil, charcoal and common salt mixed refilling of soil etc all included complete all as directed.

M&L for Supply and fixing ceiling fans complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) of Note:- Old u/s C/Fan to be deposited in MES store.

M&L in replacement exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louvers, BEE, five star rated including fixing the fan with all connecting accessories and making electric connection from c/rose etc. Old u/s E/Fan to be deposited in MES store. Fixing of Exhaust Fan on wall with suitable size anchor bolt, making hole in wall for grouting and making good the disturbed surface including plaster work shall be part of job at no extra cost. Note:- Old u/s C/Fan to be deposited in MES store.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size16 sq mm 4 core all as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified and directed.

Supplying and laying reinforced precast concrete cable cover, Class LV, Type I, flat, size 250mm x 150mm x 40mm for cable protection all as specified and directed.

M&L in replacement Galvanised steel tubes, light grade for cable protection laid in trench or concelled or fixed in wall all as specified and directed.

SWAMI ENGINEERS

rkkataria and sons

M/S Mukesh Kumar Gupta

Buttar Construction Co.

KG BUILDERS

M/S RAJ KUMAR GUPTA