MISCELLANEOUS BR REPAIR TO BUILDINGS AND ITS SERVICES AT RANGPUR VIHAR BOGRA VIHAR UMRAO SINGH ENCLAVE OFFICERS MESS UNIT AREAS AND OTHER NEARBY LOCATIONS AT SHIVMANDIR UNDER AGE BR I OF GE SUKNA

Amount

Removing/ cleaning of shrubs / grass / plants over RCC roof, chajja, wall of building of any plinth area and for any storeyed including scrapping of all algaes etc complete all as specified and directed by Engineer in charge.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for Plain Cement Concrete Type E2 1:5:10 (using 40 mm graded stone aggregate) as in sunken floor, foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified.

M&L for filling the gaps at the junction of roof sheet and vertical wall any thickness, any position and on height upto 10 m form GL using cement concrete type C1 1:3:6 (using 20 mm graded aggregate) and finish both side of wall by 15 mm rendering in cement mortar 1:6 and applying two coats of cement base paint to match with existing surface to match including necessary scaffolding upto 7 mtr height complete as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan to any radius, built in CM 1:4 as in half brick but except bricks complete all as specified and directed. Note:- Serviceable quantity of bricks obtained from demolition shall be reused.

S & F of 2nd class Hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails sectional area exc 13 but not exc. 25 sqcm complete all as specified and directed.

S&F 30 mm thick factory made flush door shutter solid core construction, with particle board core and plywood face panels,commercial type on both side with decorative face veneer with 6mm thick teak wood lipping / frame to match complete all as specied and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exceeding 1.0 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each and refixing in same opening complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

M&L for Solid PVC Wall Lining consisting of 5 mm thick wood grain printed colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete as per specifications and drawing including dismantling as per specification and drawing given on MES schedule standard of rate 2020 and complete all as per specified and as directed by Engr-in-charge

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof and including dismantling complete all as specified and directed.

S&F in repair 200 mm long aluminium, anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F in repair 125mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 75mm stainless steel butt hinges, fine grade steel soft close grinding welded head with single pin for lifetime durability, rust and corrosion proof suitable for any door, cabinets, windows and wardrobese etc complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples fixed to iron door / PVC doors / Aluminium doors / windows etc complete all as specified and as directed.

Supply and fix in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S&F in repairs Decorative curtain rod of wooden finish powder coated of 25mm dia including six nos curtain ring per running metre complete all as directed and specified.

S&F Decorative type wooden finish double brackets support for holding curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S&F in repairs magic eye 15mm dia steel body suitable for 35 to 40mm the doors with all necessary fittings complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

S&F Mild steel screw bolts diameter of neck 11 to 15 mm (machine made) with hexoganal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5 cm but not exc. 10 cm long complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F steel windows or ventilator fixed type with glazing bars and including hinges steel peg stay complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S&F Powder coated aluminium frame work (minimum thickness of powder coating 50 micron) for doors, windows, three track ventilators with one or more rebates and including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified and directed.

S&F anodised aluminium frame for doors, sliding window three track, ventilator etc with one or more rebates including all jointing cleats, etc complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F anodised (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F powder coated aluminium door shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws etc. complete all as specified and directed.

S&F non asbestos fibre cement building boards 4 mm thick (designer pattern) fixed or laid / inserted to anodised aluminium snap grid frame size 605 x 605 mm work for false ceiling cleats hangers with 6 mm dia., G.I. (length as required) adjusting level fixed to roof slabs / truss by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long and including necessary dismantling of existing unserviceable ceiling boards of any thickness including cover fillets complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instructions complete all as specified and directed.

M&L in repair 12mm thick, plywood grade BWR conforming to IS : 303 type BB fixed to screws to timber frame work as in shelves complete fixed in repair all as directed.

S&F Prelaminated particle board 9 mm, interior grade, prelaminated both side with decorative choice lamination fixed with screw to timber/aluminium frame work with suitable beading/snap grid complete all as specified and directed.

M&L machine cut kota stone slab 20-25 mm thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 20 mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the stone including dismantling old stone slab complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 20 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding finished even and smooth without using extra cement complete all as specified and directed.

M&L 25 mm thick, PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as under tile floors complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in sunken portion including demolition of old concrete complete all as specified and directed.

Roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and as directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in floor over and including 20 mm thick screed bed in CM 1:6 and including necessary dismantling complete all as specified and directed.

M&L Cement injection grout, cementitious pressure injection grout to crack or water leakage area, the injection nozzle fixing, to drilling on RCC structure and clean the holes then install nipple/nozzle, an injection aid admixture in powder form, dosage 0.8 – 1.0% by weight of cement / binder, with cement slurry to grout, Grout inject by nozzle through pressure machine, ( maximum nozzle distance approx center to center 300 mm) the admixture of use sika intraplast EP/STP/Fosroc of equivalent make is complete all as specified and directed.

M&L coloured vitrified heavy duty full digital paving tiles 10 mm thick (square/rectangular) polished, area of each tiles exc 0.11 sqm but not exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over including screed bed or bedding layer of mortar 15 mm thick for laying floor tiles in cement mortar 1:6 finished even and rough complete all as specified and as directed

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:3 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300 x 450 x 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc.0.06 sqm but n. Exc. 0.11 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement including taking down complete all as specified and directed.

M&L Rendering 15 mm thick on other than fair faces of brick work or concrete sur-faces in cement mortar 1:4 using water proofing compound @ 3% by wt of cement for finished even and smooth (without using extra cement) including taking down complete all as specified and directed.

M/L 10 mm thick cement plaster in CM (1:3) using WPC @ 3% by wt of cement in sunken portion complete all as specified and directed. (Note-WPC will be measured and paid separately)

M&L cleaning the surfaces of sunken floor using wire brush, brooming down and washing down with water to remove dust etc. and including brushing with neat cement slurry @ 0.5 kg / sqm & one coat with acrylic based polymer modified cementitous composite @ 0.50 kg / sqm complete all as specified and directed.

M&L for prepration of new plastered surfaces of wall and applying two coat of oil emulsion distemper over a coat of alkali resistant primer over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of old decorated wall surface and including applying one coat of oil bound distemper complete all as specified and directed.

M&L preparation of old plastered wall surfaces and inlcuding applying one coat of weather coat exterior paint complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4.80 mm thick plain sheet glass ordinary quality fixed with aluminium frame work exc 0.50 sqm in each pane complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, & side not less than 300mm with ABS chromium plate bracket guard complete all as specified and directed.

S & F 4.8 mm thick Frosted, obsecured or grounded sheet glass, ordinary type and glazing with oil putty/wooden beads in squares not exceeding 0.5 Sqm in each pane fixed to steel frame including steel pin complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of New steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor and including taking down of existing pipe complete all as specified and directed.

S&F 25 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc.) and fixed to wall / ceiling or laid in / on floor taking down of existing pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 250 ltr to 500 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S & F in repair 15 mm bore bib tap chromium plated, concealed type with long shank fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs Sink mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed.

S&F in repair 2 way angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S & F in repair 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repair angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, concealed type, chromium plated long thread with flange complete all as specified and directed.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs 25 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs waste fitting 32 mm bore, brass, chromium plated for basins etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for hot water supply complete all as specified and directed.

S&F in repairs Ball valves 20mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20 mm - 210 gms ) complete all as specified and directed.

S&F in repairs Ball valves 25mm dia high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 25 mm - 455 gms) complete all as specified and directed.

S&F in repair stainless steel towel rail 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) multiple floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S & F in repairs PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement complete all as specified and directed.

S & F in repairs of 125 / 110 mm size PVC (SWR) gully trap, setting and jointing with solvent cement including top cover grating complete all as specified and directed.

S&F in repairs 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing union and cap and fixed complete all as specified directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and including connection to trap and to flushing pipe including provn of line concrete holding CI anti -syphonage pipe complete all as specified and directed.

S&F in repairs vitreous china wash basin, of size 40D x 49W x 15H centimeter table top wash basin for bathroom made of ceramic star white rectangular shape over the counter basin complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs 15 mm bore Tall single lever pillar cock with chrome finish suitable for table top wash hand basins and pillar cock with tall bodies have their water outlets at a greater distance from the deck / counter than the regular pillar taps, for a heightened flow and the finish of a tap shall be have glossy, high reflective chrome finish with single quarter turn handle complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size, including shower arm with or without swivel joints complete all as specified and directed.

S&F in repairs plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges for european water closet pan complete all as specified and directed.

S&F as in repairs brass CP central hole basin mixture chromium plated 15mm bore with capstan head, screwed reed down high pressure with or without lettered "hot" or "cold with long scewed shanks and fly nuts screwed for iron pipe complete all as specified and directed

S&F in repair brass CP wall mixer chromium plated 15 mm bore with capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts, connecting legs and wall flanges screwed for iron pipe as complete all as specified and directed.

S&F as in repair Health faucet of CP 15mm bore fancy type with suitable flexible pipe as per site requirement incl CP nipple with socket complete all as specified and directed by Engr-in-Charge.

S&F in repairs PVC waste pipe for urinal / WHB 32 mm / 40 mm bore with one end with socket complete all as specfied and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Cont.)

(v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position in framed work complete all as specified and directed.

Dismantling of timber scantlings in fillets, rails, post, rafters, purlins, etc. under 40 Sqcm in section Unframed work complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

SHANTI UDYOG (BID ID -3372854)

A K ENTERPRISES (BID ID -3372435)

R N SAH N CO (BID ID -3372012)

KARMIBRINDA (BID ID -3372471)

MS ORIENT ENGINEERING WORKS (BID ID -3371844)

M/s TRIMURTI ASSOCIATE (BID ID -3372645)

M/S EASTERN ENGINEERING (BID ID -3372568)

SHIVALAYA ENTERPRISES (BID ID -3370922)