PROVN OF A VEH, SPL VEH PARKING SHED WITH HARD STANDING, PROVN OF JCOs SINGLE LIVING ACCN AND CERTAIN OTHER SANCTIONED WORKS IN THE AOR OF AGE BR I UNDER GE HISAR AT HISAR MIL STN

Amount

Surface dressing not exc 15cm deep in soft/loose soil complete all as specified.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

Earth filling under floors including spreading, leveling, watering and well ramming in layers not exc 25 cm thick. Note :- Earth obtained from excavation under item 3.00 here-in-before shall be used for filling.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil all as specified.

M&L for hardcore of broken bricks, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete all as specified.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete all as specified.

M&L for precast RCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in landings, cover slabs (for man holes, drains etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including placing in position and set in CM (1:6) complete all as specified & as directed. Note :- Reinforcement shall be measured and paid for separately.

M&L for PCC 1:3:6 type C0, using 12.5mm graded crushed stone aggregate as in filling up chowkat hollows and similar works as directed, complete, all as specified.

M&L for cement concrete 1:2:4 type B1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified.

M&L reinforced cement concrete M-25 (Design mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in lintels upto 1.5m clear span, seismic and other similar bands, lintel bands, plinth bands, roof bands and the like. Note :- (i) Reinforcement shall be measured and paid for separately. (ii) The quoted rates include for use and waste of formwork (straight or curved).

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified.

M&L formwork to edges of concrete flats, roofs, floors etc not exc 10cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work not exc 10cm wide for rough finished surfaces all as specified.

Supply only integral water proofing compound (ISI marked).

M&L 40mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in damp proof course on horizontal surface including necessary formwork complete all as specified & as directed.

M&L for 50 micron heavy duty Polythene sheet (White), laid on rammed earth/over PCC complete all as specified & directed.

M&L for brick work using old size fuel ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work using old size fuel ash bricks as specified in clasue 6 of Particular specification, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified.

M&L for Continuous brick edging using old size fuel ash bricks as specified in clasue 6 of Particular specification, with width equal to the width of the brick, laid dry on end vertically complete all as specified.

S&F factory made 35mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides all as specified and directed.

S&F factory made 35 mm thick plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class Hard Wood rail and styles, fixed to chowkat, complete all as specified & directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (with sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S & F factory made Fibre glass reinforced plastic (FRB) door frame of three legged or cross section 90x45mm size, single rebate of 32x15mm to receive shutter of 30mm thickness, laminate door frame moulded with two resistant grade unsatrated polyster plain and chapped matd or frame laminate shall be 2mm thick and shall be filled with fibre glass form from all sides, MS stay shall be provided at the bottom to steady the frame complete all as per sample fixed in MAP Ph-II Accn complete all as specified and directed. Make :- Fibreways or equivalent of makes mentioned in Appx 'C' here-in-after.

S & F 30mm thick factory made Fibre glass reinforced plastic (FRB) panelled door shutter of approved colour, made with fire resistant grade unsatrated polyster plain moulded to 3mm thick fibre laminte for forming hollow ralliuded styles with wooden frame and suitable blocks of seasoned wood inside at required place for fixing of fibre cast monolithically with 5mm thick FRB laminated for panels and conforming to IS-4858-2000 complete all as per sample fixed in MAP Ph-II Accn complete all as specified and directed. Make :- Fibreways or equivalent of makes mentioned in Appx 'C' here-in-after.

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications etc complete all as specified and directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour sheets for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F aluminium handle 150mm size cast type, anodized complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F 100mm long aluminium anodized floor door stopper double legged with rubber shoe, fixed to bottom rail of door as directed.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staple complete all as specified.

S&F curtain rod (drapery rod), mild steel powder coated, 32mm dia, fancy type with fixing brackets, stops, rollers, ends/finales etc complete all as specified and directed.

S&F factory made pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, mild steel sheet of 1.25 mm thickness complete as specified & as directed. Note :- Rates quoted deemed to include S&F of hinges, lugs, lock strike plate.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete with glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Details of box type window shall be given on HQ CEJZ drawing No TD/2013/01 sheet 1/3, 2/3, 3/3. (iii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows, ISI marked, (Box Type) with side hung shutters including box type hinges with steel handle etc complete without glazing bars dovetailed or welded including one shop coat of Zinc chrome primer including making good disturbed surfaces of walls, complete. Notes:- (i) The rate quoted by the contractor are deemed to be included for one shop coat of red oxide zinc chrome primer on steel windows. Nothing shall extra paid on this account. (ii) Details of box type window shall be given on HQ CEJZ drawing No TD/2013/01 sheet 1/3, 2/3, 3/3. (iii) Glass pane/wire gauze shall be measured and paid separately.

S&F factory made Steel windows or ventilators, fixed type, with glazing bars all as specified & directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 44.00 here-in-before but 5 to 10mm dia in stirrups, spacers and binders.

S&F mild steel framed work using ERW or induction butt welded tubes conforming to I.S 1161-1979 Grade St-240 including necessary welding, bolting, special shaped washer, clamps, cleats etc. complete all as specified & as directed.

S&F rolled mild steel work as in Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment including necessary welding etc. conforming to Gde E-250 (Fe 410-W) quality `A’ all as specified and as directed.

S&F mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 30cm long, dia of neck exc 20mm but not exc 25mm complete all as specified & as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm bot not exc 10cm long and dia of neck 5 to 10mm complete all as specified.

S&F mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete, all as specified & directed.

M&L mild steel work as in Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar workconforming to Gde E-165 (Fe 290) all as specified and directed.

S&F mild steel framed work as in steel frames, chowkats, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified & directed.

S&F Anodised aluminium snap grid size 605 x 605mm frame work for false ceiling complete all as specified & directed.

S&F hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

S&F False ceiling with 4mm thick HPSC pre-primer non asbestos fibre cement building board (E-Classic) with decorative finish, factory made, 600mm x 600mm in size and complete all as specified & as directed. Note : The snap grid frame work shall be measured & paid for separately

M&L applying evenly a tack coat of industrial bitumen 85/25 grade at the rate of 1.20 Kg per sqm including cleaning surfaces complete all as specified.

M&L for 80mm thick average consolidated thickness mud phuska on flat roofs including 25mm thick mud plaster but excluding leeping plaster etc complete all as specified and as directed.

M&L 40mm thick brick tiles laid on mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on mud phuska complete all as specified.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 100 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 50mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor top, surface finished even & smooth without using extra cement, spike rolling to surfaces or marking impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

M&L for 150mm thick PCC 1:2:4 type B1 using 20mm graded crushed stone aggregate as in floor top, surface finished even & smooth without using extra cement, laid in alternate bays of size as directed by Engineer-in-charge complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in levelling course 25mm thick finished fair & even complete all as specified & as directed.

M&L for machine cut Kota stone slab flooring 20 to 25mm thick laid over & including screed bed or bedding layer of 15mm thick in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified. Note : - Kota stone shall be of size 550mm x 550mm (minimum) when brought at site.

M&L machine cut Kota stone slab 15 to 20mm thick , as in skirting etc. laid over & including screed bed or bedding layer of 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L for vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic jointless tiles (coloured) 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M & L for glazed ceramic jointless tiles (coloured) 450x300x7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over & including 10mm thick screed bed in cement & sand mortar 1:4 complete all as specified and as directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L for factory made vibrate type chequered cement concrete tiles, 25cm x 25cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement & pigment, laid over & including 20mm thick screed bed in cement & sand mortar 1:4, complete, all as specified & as directed.

M & L for Soling (or sub base) 200mm thick with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber complete all as specified & directed.

M&L for forming Contraction (Dummy) joints 100mm deep x 10mm wide, filled with sealing compound with bitumen and sand mixture (1:3) by weight all as specified and directed.

M & L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M & L for rendering 15mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for rough cast finish plaster by applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even complete .

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over a coat of alkali resistant primer complete all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including MS glazing clips not less than 06 nos per pane and painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.

M&L for preparation of new steel surfaces (already applied with coat of primer) of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint of approved tint on existing primer complete all as specified.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors all as specified.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F 15 mm bore bib tap, long shank, cast copper alloy, fancy type, chromium plated, with capstan head, screwed down, screwed for iron pipe or for brass ferrule.

S&F 15mm bore angle cock, one way, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F 15mm bore Stop valve, cast copper alloy, fancy type chromium plated, screwed down, high pressure with capstan heads, screwed both ends for iron pipe or for union.

S&F 20mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S & F 15mm bore stop valve, fancy type , chromium plated cast copper alloy screwed down, high pressure, with long shank and cup (concealed type) with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed.

S&F 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes.& fly nuts, screwed for iron pipes.

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe of 20mm bore.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S&F shower rose of PTMT any colour for fixing with 195mm long with bend of 45 degree with flange of PTMT (Minimum wt 80 gms) etc complete all as specified and directed.

S&F Grating doom 100 mm dia with waste hole of PTMT (Minimum weight 25 gms) all as directed.

S&F vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F brass CP jet assembly for water closet (pedstal pattern) etc complete all as specified and as directed.

S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including PTMT nuts on both sides complete all as specified.

S&F vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor, complete all as specified.

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F vitreous china bowl type urinal flat back, size of 465 x 355 x 265mm (minimum) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia complete all as specified.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F PVC(SWR) branch piece double (double Y) equal or unequal 110mm bore etc complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) floor trap dia of outlet 75mm, with PTMT grating including jointing with solvent cement all as specified.

S&F PVC (SWR) floor trap dia of outlet 110mm, with PTMT grating including jointing with solvent cement all as specified.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed (in CM 1:1) complete with collars all as specified & as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or ¾ section) in cement concrete (1:2:4) type B-1 using graded stone aggregate, smooth finished and reforming benching as required for 150mm bore pipe etc complete all as specified and directed by Engr-in-Charge.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3 mm thick new bakelite laminated sheet top cover ‘Hylam’, complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 125.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch.

All as per item No. 125.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board.

All as per item No. 125.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board.

All as per srl item No. 125.00 (here-in-before) but for 15 Amp socket out let by using 2.50 Sqmm PVC insulated unsheathed copper conductor cable FRLS multi strand on independent board including provn of 2.50 Sqmm unsheathed, multi stranded copper conductor cable FRLS continues as earth wire connected to earth dolly etc complete all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5/6 Amp, 230 Volts all as specified & directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts.

S&F flush type socket outlet multipurpose 3 Pin 5/6 Amp (with 2 pin outlet also) 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp (with 3 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F lamp holder, insluated body, with back plate suitable for batten fittings & complete all as specified & directed.

S&F ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F Ceiling fan regulator electronic step type of suitable wattage, 230V suitable for 1200/1400 mm ceiling fan etc complete all as specified and directed.

S&F LED bulb of capacity 15 W, ISI marked, all as specified and directed.

S&F LED light fitting 1x18W, batten for Retro LED energy saving tube light, ultra bright LED polycarbonate Tubelight with very high efficacy ready to use pack including LED tube single side connection all as specified and directed. Make : Havells Regal batten Cat Part No REGALBATTENT5UPTO1X18WDSBSWH & LED tube rod Cat Part No PHOTONULTRA1213T8SSTL18WLED865SPC or Syska Cat Part No SSK-TST-18W or Cat No LT 8-20-865-2 of Crompton or equivalent of makes as mentioned in Appx 'C' list of makes.

S&F street light LED light fitting 60 Watt, pressure die cast housing with epoxy powder coating, toughened glass cover having IP66 protection, prismatic polycarbonate cover with individual LED lense connected with and including 0.5 sqmm flexible copper multistranded conductor cable and including security light bracket made to shape out of GI pipe 40mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed fixed on pole / wall all as specified and directed. Make : Cat Part No ENDURAPEARLSL60WLED757SASYTOPC of Havells, Cat No LTESS24x2.5HPLED/LS of C&S or equivalent of make as mentioned in Appx 'C' list of makes here-in-after.

S&F street light LED light fitting 18/20 Watt, pressure die cast housing with epoxy powder coating, IP65, connected with and including 0.5 sqmm flexible copper multistranded conductor cable including security light bracket made to shape out of GI pipe 40mm dia light grade 1.5m length and fixed with MS clamps of size 40x5mm - 2 Nos, nuts, bolts and washers fixed on wall all as specified and directed. Make : Cat Part No ENDURAPEARLSL20WLED757SASYTOPC of Havells, Cat No SSK-SLF-CF-18W of Syska, Cat No LTESSE18WLED of C&S, Cat No HLSLD-09-18-CWL-R of Halonix or equivalent of make as mentioned in Appx 'C' list of makes here-in-after.

S&F LED flood light 40 Watt, energy saving, powder coated PDC aluminium body with toughened glass visor having efficacy > 100 lm/w IP 66 protection including connecting to ceiling rose & with MS clamp suport for hanging of light of suitabel size complete all as specified and directed. Make : Polycab Cat Part No PCGLFT1 02 40 57 or equivalent of makes as mentioned in Appx 'A' list of makes.

S & F sheet metal enclosure, double door type, IP protection 43 having door earthing, suitable for fixing MCBs, TPN with 200 Amps rated bus bar, 4 way, 240 Volts. Make :- Optipro of Indo Asian Cat Part No 811841 or equivalent of makes mentioned in list of makes here-in-after .

S & F sheet metal enclosure, double door type, IP protection 43 having door earthing, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 8 way, 240 Volts. Make :- Optipro of Indo Asian Cat Part No 811807 or equivalent of makes mentioned in list of makes here-in-after .

S & F sheet metal enclosure, double door type, IP protection 43 having door earthing, suitable for fixing MCBs, SPN with 200 Amps rated bus bar, 4 way, 240 Volts. Make :- Optipro of Indo Asian Cat Part No 811805 or equivalent of makes mentioned in list of makes here-in-after .

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S & F MCB SPN, 32 Amps 240 Volts , 'C' curve, 10 KA, complete. Note :-Make of MCB shall be same of that DB.

S & F MCB TPN, 63 Amps, 415 Volts , 'C' curve, 16 KA, complete. Note :-Make of MCB shall be same of that DB.

S&F ventilating fan 200mm sweep, 230 Volts, 32 Watt, fixed on wall including provn of opening complete with suitable size nuts, bolts & washers and connection with & incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed. Make : Model No Ventil Air-DX of Havells or equivalent of make as mentioned in Appx 'C' list of makes here-in-after.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting exc 10 cm but not exc 20 cm girth in brick walls.

S&F 5 star rated energy saving ceiling fan 1200mm sweep with double ball bearing and three blades with all accessories, down rod, two nos canopy, white in colour including 2 core 0.5 sqmm copper flexible cable for connection from ceiling rose to fan complete all as specified and directed. Make : Crompton Cat Part No HB Plus 5 star / Usha Cat Part No Technix Plus / Orient Cat Part No Energy Star or equivalent of makes as mentioned in Appx 'A' list of makes.

M&L for sub main wiring with two runs of 6 sqmm (nominal area) size main cable & one run of 6 sqmm size earth continuity conductor in green colour, single core, PVC insulated, unsheathed, FRLS with multi-stranded copper conductor, 1100 Volts grade, ISI marked (IS: 694) cables, drawn through & including PVC conduit fixed on wall/ceiling with PVC saddles, ISI marked & conduit fittings/accessories of medium grade not less than 25mm dia complete including dismantling & taking down old unserviceable sub main wiring. Note :- 02 runs of 6 sqmm size, 01 run of 6 sqmm size cable & conduit with accessories shall be measured as one run length for payment purpose.

S&F House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified.

Supply , laying , jointing, testing and commissioning of cable of size 16 sqmm 4 core LT underground cable , 1100 volts grade, XLPE insulated and PVC sheathed, armoured heavy duty with multistrand aluminium conductors as per IS 7098 (Part-I), laid in trenches /fixed on wall /floor /road /culverts /pole or encased in GI pipe complete all as specified. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness afterlaying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

M&L for brick covering to underground electric cable using sub class ‘B’ bricks, laid dry, flat, perpendicular to the direction of cable etc complete all as specified and directed. .

S&F Galvanized iron tubing, 50mm bore light grade, ISI marked, including all fittings and laid in trenches/under road/drains, fixed to poles/walls with required size of flat iron (40mmx6mm) clamps, bolts, nuts and washers for protection of LT electric cable complete. Note :- Excavation & earthwork shall be measured & paid for separately.

S&F 1100 Volts grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of aluminium stranded conductors of size 10 Sqmm all as specified & directed.

M & L for earthing complete with galvanized iron earth plate electrode of size 60cmx60cmx6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, connected to the galvanized earth lead wire 4mm dia by means of GI bolts/nuts/ washers, protected by 15mm bore GI light grade pipe from earth plate and upto 3m along pole fixed with 2 clamps made from mild steel flat iron 25x3mm bolts, nuts and washers etc. Earth plate shall be surrounded by packed layer of coal dust 300mm and common salt 15cm thick all around bottom and top, 20mm GI medium grade pipe for watering and including funnel , wire mesh , RCC 1:2:4 type B-1 using 20 mm graded stone aggregate cover of size 30 cm X 30 cm X 8 cm thick reinforced with expanded metal weighing not less than 4Kg/Sqm, PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in earthing pit including necessary excavation and earth work, all as specified and shown in electrical plate No-3 of SSR part-I and connected to earthing point and testing on completion complete all as specified & as directed. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode and pipe for watering shall be provided in slanting manners.

Balaji Construction Co.

PAWAN KUMAR

M/S KAVITA CONSTRUCTION

M/S Punia Constructions

malik constructions

Shiva Constructin Co.

P.K. ENTERPRISES