Repairs to joinery and sanitary fittings at KMC and Defence Civilian Colony and repairs to roof civil and other connected works to certain bldgs at Juhu under GE North Mumbai

Amount

Demolition of brickwork built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed by Engineer-in-Charge.

Demolition cement concrete (reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) etc complete all as specified and as directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, in hard/dense soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, and removing surplus soil to a distance not exceeding 50 m and depositing where directed and making good the disturbed surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Material and labour for Pre-cast cement concrete (1:3:6), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 etc complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for 5 mm thick plastering in cement mortar (1:3) on internal ceiling surface and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick rendering in two coats (10mm + 5mm) with cement mortar 1:4 of any thickness on fair faces of brick or concrete surfaces, finished even and fair mixed with water proofing compound @ 2% by weight of cement in CM 1:4 etc complete all as specified and as directed by Engineer-in-Charge. Note: WPC will be measured and paid separately.

Material and labour for 10 mm thick plastering in cement mortar (1:4) on internal wall surface including dubbing out plaster in cement mortar (1:6) of any thickness finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails, and fastenings and heavy bracket framing, (beam, tee, angle, channels or flat sections) including notching, drilling, fitting, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts) conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rolled mild steel in joist, channel, angle, or tee sections,fixed independently, without connecting plates conforming to Fe- 290, Gde 165 etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS. 1161-1979 grade St-240, complete all as specified and as directed by Engr-in-Charge.

Dismantling of timber scantlings 40 sq cm and over in section as in unframed work,in any position complete all as specified and as directed by Engr-in-Charge.

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good in cement concrete in frame complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Cutting holes in brick walls in cement mortar for inserting angle iron trusses/ rafters of depth exc one brick but n.exc two bricks complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Plain cement concrete 1:2:4, type B1 Nominal mix using 20mm graded stone aggregates as in bed block of angle iron post and coping at security wall and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary form work for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer with all necessary staging, scaffolding etc as required complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints / Berger paints / Shalimar paints / Dulux

Material and labour for preparing new wood surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian paints/ Nerolac paints/Berger paints/ Shalimar paints/ Deluxe

Dismantling asbestos cement (corrugated or semi corrugated) sheets in roof coverings including ridges complete all as specified and as directed by Engineer-in-Charge

Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Supply and fix Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Dismantling of 110mm dia PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Dismantling of 75mm dia PVC pipe including bends/branch pipe jointed in cement mortar and taking out if required complete all as specified and as directed by Engineer-in-Charge

Supply and fix UPVC (SWR) single socketed rain water pipes/ soil waste pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) single socketed rain water pipes/ soil waste pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) vent cowl 110 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Supply and fix UPVC (SWR) vent cowl 75 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex

Dismantling wall and ceiling boards, any thickness, including cover fillets complete all as specified and as directed by Engineer-in-Charge.

Supply and fix anodised aluminium snap grid frame work for false ceiling conforming to IS 733, IS 737 and IS 1285 including all ceiling cleats, 4 mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm , cross tee and wall angle of size 23.50 x 23.50 x 1.5 mm with 605 x 605 mm grid system including 12mm thick gypsum board with all connected accessories suitably placed in false ceiling grid as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: Gypsum board /Arm Strong/Ramco/Bisan

M&L for anodised aluminium snap grid frame work for false ceiling confirmionmg to IS - 733, IS-737 and IS - 1265 including all ceiling cleats, 4mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm, cross tee and wall angle of thick 23.50 x 23.50 x 1.50 mm thick 605 x 605 mm grid system including Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm gridas per manufacturer instruction complete with necessary design in single/double all as specified and as directed by Engineer-in-Charge. Make: Gypsum board /Arm Strong/Ramco/Bisan

M&L for anodised aluminium snap grid frame work for false ceiling confirmionmg to IS - 733, IS-737 and IS - 1265 including all ceiling cleats, 4mm dia GI wire suspender with necessary main tee 35.00 x 23.50 x 1.50mm, cross tee and wall angle of thick 23.50 x 23.50 x 1.50 mm thick 605 x 605 mm grid system including Exposed metal frame ceiling with Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) as per manufacturer instruction complete with necessary design in single/double all as specified and as directed by Engr-in-Charge.

Material and labour for preparation of new plastered wall surfaces and applying two coats of Acrylic weather proof coat 100% exterior grade paint over acrylic primer complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Berger paints / Shalimar Paints

Material and labour for preparation of new plastered surfaces of ceiling and applying three coat of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered internal surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed by Engineer in Charge. Make: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)

Material and labour for preparation of new plastered ceiling surfaces and applying two coats of distemper oil emulsion (White colour) over a coat of priming plastered surfaces complete all as specified and directed by Engineer in Charge. Make: M/s SHALIMAR / M/s BERGER / M/s NEROLAC /M/s ASIAN (Tractor Brand)

Dismantling PVC water tank exceeding 250 ltr but not exceeding 500 ltr capacity and removing to store all as specified and directed by Engineer-in-Charge

Dismantling PVC water tank exceeding 500 ltr but not exceeding 1000 ltr capacity and removing to store all as specified and directed by Engineer-in-Charge

Dismantling PVC water tank exceeding 1000 ltr but not exceeding 2000 ltr capacity and removing to store all as specified and directed by Engineer-in-Charge

Supply and fix rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 500 ltrs capacity with inlet & outlet connections, tank nipple(minimum weight 25mm - 65 gms) 25mm bore dia, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Sintex/Polycon/infra/Rotex

Supply and fix rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 1000 ltrs capacity with inlet & outlet connections, tank nipple(minimum weight 25mm - 65 gms) 25mm bore dia, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Sintex/Polycon/infra/Rotex

Supply and fix rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 2000 ltrs capacity with inlet & outlet connections, tank nipple(minimum weight 25mm - 65 gms) 25mm bore dia, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Sintex/Polycon/infra/Rotex

Supply and fix in repairs gun metal gate valve, 20mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/GEM

Supply and fix in repairs gun metal gate valve, 25mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/GEM

Supply and fix in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe of 20mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe of 25mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

All as per item No.50 described here-in- before but 20 mm bore complete all as specified and as directed by Engineer-in-Charge

All as per item No.50 described here-in- before but 25 mm bore complete all as specified and as directed by Engineer-in-Charge

Demolition of the existing brick coba treatment over roof slab completely including thoroughly cleaning complete all as specified and removal of the demolished material to outside of MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for PCC 1:2:4 type B0 (using 12.5 mm graded aggregate) with 2% by weight of cement or as per manufacturer's instructions water proofing as in levelling course, haunching, coping and similar works over RCC roof surface and RCC over head tank top surface including rounded or chamfered on edges and formwork etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for APP modified waterproofing treatment over existing RCC roof slab with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.90 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide 20mm thick screed in cement mortar 1:4 mixed water proofing compound at the rate of 2% by weight of cement (d) Provide 300 x 300 x 20mm thick machine pressed cement concrete tiles with minimum thickness of joint (not exceeding 3mm) are thoroughly filled with water proof polymer based joint mortar. Note : (i) Water proofing compound will be measured and paid separately (ii) Quoted rate includes the disconnection existing tanks of any litres capacity including all fittings, setting aside (for lowering if reqd) for roof treatment & reconnecting and refixing in position including all fittings complete all as directed.

Material and labour for APP modified waterproofing treatment to parapet wall with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4 lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.90 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide a solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm prescribed by manufacturer complete all as specified. Note : Quoted rate includes the disconnection existing tanks of any litres capacity including all fittings, setting aside (for lowering if reqd) for roof treatment & reconnecting and refixing in position including all fittings complete all as directed.

Material and labour for removing vegetation, trees, plants and shrubs etc in any position by cutting hole into brick wall / concrete surfaces (for removing the roots of trees/plants) area not exceeding 0.50sqm each and using acid to burn the all roots of tree/plants and making good disturbed surfaces with cement concrete 1:2:4 type B1, using 20mm graded stone aggregate mixed with and including water proofing compound @ 3% by weight of cement and including making good adjoining surface with existing finishes all as specified and as directed by Engineer-in-Charge. Note: The unit quoted rate shall be deemed to include WPC & necessary scaffolding as required.

Taking down chowkats or frame with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Taking down of chowkats or frames exceeding 1.5sqm but not exceeding 4 sqm with shutters (without taking off shutters from the frames) including all fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each including fittings & removing clear off site after credit for the same is recovered by dept complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exceeding 1 sqm but not exceeding 2 sqm each and and refixing the same including fittings complete all as specified and as directed by Engineer-in-Charge.

Supply and fix factory made plain framed panelled shutter 35mm thick 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 35mm thick factory made 2nd class hard wood glazed and skelton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pvts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix 30mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both side all as specified and as directed. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6Nos screws to be provided for each frame all as specified and as directed by Engineer-in-Charge. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 156 of SSR Part II (pertaining to item No 08080) complete all as specified and as directed by Engineer-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S TUFFFLON/M/S Dura Plast Extrusion

Supply and fix mild steel work as in hold fast & similar small articles, conforming to Fe-290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) as in bed plates, concrete block for hold fast etc including necessary form work complete all as specified and as directed by Engineer-in-Charge.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 150mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix Stainless steel butt hinges medium weight of size 75mm all as specified and as directed by Engineer-in-Charge.

Supply and fix Stainless steel butt hinges medium weight of size125mm all as specified and as directed by Engineer-in-Charge.

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix in repair extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix in repairs 25mm dia stainless steel curtain rail fixing with including provision of pair of brackets, stops, rollers etc complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in Cement mortar 1:6 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles

Material and labour for joint free, coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick/ 450mm x 350mm x 7mm , on vertical surfaces etc., set and jointed in neat cement slurry and pointed in coloured cement to match over & including cement plaster 10mm thick in Cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Nitco tiles / RAK tiles

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in Cement mortar 1:6 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles

All as per item No.above but in skirting/dado including 10mm thick Cement Mortar 1:4 rendering of backing layer complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25mm thick cement concrete nominal mix 1:2:4 (using 20mm graded stone aggregate) type B-1 as in sub base, floor,pavings etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cement, including joints of plinth protection filled with bitumen mastic (1:3) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-Termite Treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-Termite Treatment soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-termite Treatment Treating to the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed by Engineer-in-Charge.

Demolition of stone slab and tiles of any description or thickness in floor, apron and vertical surfaces, laid dry or laid dry and pointed and removing debris outside MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for granite (Mashroom granite) machine cut, (table rubbed and polished) , slab 20mm thick as in steps, jambs, pillars, window cill, kitchen platform set, bedded and jointed with grey cement slurry mixed with admixture of pigment to match the shade of granite slab including cutting, nosing rubbing and polishing etc laid over and including screed bed or bedding layer of 20mm thick in cement mortar (1:4) all as specified and as directed by Engineer-in-Charge.

Material and labour for 20 mm thick Makrana colour/white marble machine cut on kitchen platform, over cement screed base laid and joined with gray cement slurry mixed with pigment to match the shade including edge cutting , nosing , rubbing and polishing incl 20 mm thick screed bed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, complete all as specified and as directed by Engineer-in-Charge. Make : Slim line/Commander/Hindustan.

Supply and fix in repairs vitreous china wash hand basin, white, flat back of size 550 mm x 400 mm excluding taps, waste chain and plug and porcelain stopper including brackets, chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson Note:- Pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately as "Supply only

Supply and fix in repairs pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs, concealed stop valve fancy type cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repairs CI floor trap 100mm with grating including jointing with waste pipe, fixed in cement concrete 1:2:4 type B1, Complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme

Supply and fix in repairs CI nahani trap 100mm with grating including jointing with waste pipe, fixed in cement concrete 1:2:4 type B1, Complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme

Supply and fix in repairs, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever CI brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste pipe etc complete all as specified and as directed by Engineer-in-Charge. Make : Diamond / Nirali / Neelkant/Parryware/Prayag

Supply and fix in repair Swivel Shower of PTMT any colour for fixing with 15 mm pipe (Minimum weight 40gms) complete all as specified and as directed by Engineer-in-Charge. Make : Prayag / R.S. Industries (POLYTUF)

Supply and fix 32mm dia low density polyethylene pipes (LDPE) of pressure rating @ 6 kg/ cm2 fixed to wall complete all as specified and as directed by Engineer-in-Charge. Make: Finolex/Prince/Kisan/Supreme/SFMC

Material and labour for surface preparation of structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer-in-charge, (including removal of external plaster, wherever exists) costs inclusive of transportation, labour, conveying debris away from the site (max 50m) tools and tackles, lead and lift etc, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Supply and fix mild steel TMT bars, 8 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required inch cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge. Note: Cutting of rusted reinforcement & welding shall be inclusive in this item of work

Demolition of reinforced cement concrete of any description in any position including necessary scaffolding arrangement (reinforcement cut as required to facitate demolition) and removing concrete debris and depositing outside MD land all as specified and as directed by Engineer-in-Charge. Note : Reinforcement obtained from this item shall be handed over to contractor on account of sch of credit .

Supply & fix MS/TS dowel pins/staple/shear pins including drilling holes in concrete and providing labour and but excludes the materials for grouting the pins.etc complete all as specified and as directed by Engineer-in-Charge.

Repairing of excessively damaged concrete portion by using superfluid dual shrinkage compacted and providing, casting with micro concrete of grade M-40 at all levels with all leads and lift as directed including mixing, laying, levelling, finishing including curing and formwork of steel or marine ply complete all as specified and directed by Engineer-in-Charge. Make: Fosroc / SIKA / BASF / Krishna Conchem or equivalent approved .

M&L Reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in wall, beams and columns in floors, roof, landing, balconies etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for formwork using steel shutters or 12mm marine ply to have the smooth finish to pour the micro concrete/ concrete including de-shuttering etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and applying rust cleaner (Re-backler solution) to exposed corroded reinforcement @ 0.20 Litre/Sqm or approved make over prepared reinforcement, including removing concrete all around reinforcement including from behind the reinforcing bars by manual methods such as hammering the rebar, using wire brushes, chiseling, etc. and applying rust removing solution of approved make with cotton waste swab to reinforcements etc complete as directed by Engineer-In-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika

Material and labour for providing and applying two coats of anticorrosive epoxy phenolic rebar protective system IPNet RB or equivalent of approved make and quality comprises of resin and hardener mixed in equal proportion by volume with minimum 9-10 hours between the coats, sprinkling dry sand when 2nd coat is tacky so as to provide rough finish and ensuring air curing of minimum 10 hours after the top coat before any subsequent treatment etc. including scaffolding etc complete all as specified and as directed by Engineer-in-Charge. Note: (a) New Reinforcement shall be measured and paid separately under respective item. (b) Cost of welding deemed to be inclusive in this item of work. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour for providing and applying a priming cum bonding coat of two component Epoxide Resin conforms to ASTM-C-882-91 of approved make and quality to clean and sound concrete area by brush or any other established method by mixing Base and curing agent in 2:1 proportion by weight for joining old and new concrete as per technical specifications of manufacturer. Work shall be carried out as per the manufacturers specifications & certificate on this account shall be taken from consultant and as approved by Engineer-in-charge Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour Drilling and fixing teflon nozzles in RCC members, including drilling holes (drilling 12 mm dia, 40mm deep holes in structural members at the intervals of 600mm c/c in staggered manner or s directed by Engineer-in Charge in RCC structure elements and cleaning the holes (to clean the holes by air blower prior to fixing nozzles) and fixing of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles (to insert 12mm dia teflon nozzles in cleaned holes external end of nozzles to be machined to receive outlet of grouting gun and fixing it inside the holes by applying thixotropic epoxy putty to ensure complete sealing and curing the system for minimum 12 hrs) and cutting of nozzles (to cut the nozzle by chisel after completion of grouting without damaging structural elements etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Injecting low viscosity (3-5 cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories, till nozzles refuses to accept the grout, Including, Mixing of materials( Mixing material components (part a & b) in required quantities as per manufacturer’s instruction by weigh batching) and Grouting ( Filling the grouting gun with monomer. Maintain desired pressure in the gun by air compressor; maintain the pressure at exit (4 to 5 Kg/ Cm2) by monitoring pressure gauge at exit. Grouting the material through prefixed nozzles in the structural elements till its refusal. Sealing the nozzle with epoxy putty after the refusal. Monitoring leakages through other nozzles while grouting and seal them as per the requirement. Repeat the process for all the nozzles. the operation to be within pot life of the material.)and Cleaning of gun and accessories ( the gun and accessories like valves, pipes and other fixtures to be cleaned with thinner after the operation to avoid jamming of the gun.) etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour for providing and laying 20 mm thick POLYMER MODIFIED MORTER over identified R.C.C. members in One layer in proportion of 1:5:15 by weight of polymer of approved make, cement and filler material of approved make, blended to a required consistency and applying and finishing by floating, curing after initial setting time, including providing and inserting 10 mm mild steel shear key bars (minimum 3 nos per sqm), wherever required, bonding slurry, etc complete all as specified and as directed by Engineer-in-Charge. Make- Dr FIXIT/ FOSROC/ Krishna Conchem/BASF/Sika as approved by GE

Material and labour for Strengthening structural elements with non metallic composite fiber wrapping system comprise of uni-directional carbon fiber sheet (430 GSM) and compatible saturate Profiling, applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixotropic epoxy putty etc. , complete mechanized wetting of fiber sheet, cutting the fabric to required size, mixing of saturate and filling in tub area of the saturation machine, placing the fiber on metallic rods and pass through the rollers of machine and saturate tub ensuring complete wetting (65% fiber volume fraction) of fibers, removing the fiber on rod and placing the new fiber sheet, wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc., repeating the same procedure for multiple layer with the interval of 8 hrs ,applying second coat of saturate after minimum 12 hrs after first coat, rectify air voids if any and finally rendering with10mm thick in CM 1:6 including finishing even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Mode of measurement- Per sq.mt of surface area of carbon fiber sheet without lapping. Make- FOSROC/FIXIT/Krishna Conchem/ Sika

Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50X55 system, spreading the anchor fibers in star pattern including application of saturate complete all as specified and as directed by Engineer-in-Charge. Note for Item No.1 to 16:- (i) The work under Item No. 1 to 16 shall be carried out by authorised applicator only. (ii) Defect liability for these items shall be 5 years from certified date of completion. (iii) Amount of 5% of these items shall be retained during RAR and FB. This amount shall be released after successful completion of Defects liability period as mentioned above. (iv) Non destructive testing shall be got carried out through IIT / NIT / College of Engineering Pune to decide fulfillment of fitness criteria of structure. (v) The test shall be carried out at each discrete location or locations decided by GE or testing authority. (vi)The cost of testing shall be deemed to be included in the rate quoted by the contractor. Completion shall be issued by GE after only getting structural stability certificate of each respective building from testing authority.

Supply and fix Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Prelaminated particle board 18/19mm thick , interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15 micron coloured aluminium sections for sliding or open able windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 4.0mm thick black glass, ordinary quality in square exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick figured glass, pin headed type ordinary quality fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supply and fix 15 micron coloured aluminium anodised grill of design No DG-101 or RG 102, 10 mm thick, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Supply and fix aluminium anodised curtain rail, 25mm dia with including brackets, etc complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs for anodised aluminium brackets for curtain rods quality and design as approved by Engineer in charge.

Supply and fix in repairs vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed by Engineer-in-Charge.

Taking down wall panelling and similar work complete all as specified and directed by Engineer-in-Charge.

Supply and fix for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix for solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame etc complete all as specified and directed by Engineer-in-Charge.

Disconnecting of PVC water storage tank of capacity exceeding 250 ltrs and not exceeding 500 ltrs, setting aside (or lowering if required) for repairs, cleaning with bleaching poeder and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc., and hoisting if required reconnecting and refixing in position including provision all necessary fittings etc complete all as specified and as directed by Engineer-in-Charge.

Disconnecting of PVC water storage tank of capacity exceeding 500 ltrs and not exceeding 1000 ltrs, setting aside (or lowering if required) for repairs, cleaning with bleaching poeder and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc., and hoisting if required reconnecting and refixing in position including provision all necessary fittings etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour in repairs for 15mm thick rendering in cement mortar 1:3 mixed with water proofing compound on sunken floor including vertical surfaces upto 450mm height and using & applying a coat of Raincoat solution of make Dr Fixit or equivalent with uniform surfaces and supply and fix vitreous china squatting pan Orissa pattern pan of size 580 x 440mm white with integral foot rest 'P' trap, and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern) and connecting piece of CI pipe as per required upto T/Y joint including filling PCC 1:4:8 type D2 and over 40mm thick PCC 1:2:4, type B0 for floor laid with uniform surfaces of wall for area of toilet not exceeding 2.0 Sqm a all as specified and as directed. Make of IWC : M/s Hindustan Sanitary Ware / Parryware / Jaquar / CERA / M/s Johnson Peddar

Material and labour for opening out cracks in wall surfaces in 'V' shape by mechanical grinder and removing the loose material. filling with crack filler of Dr. Fixit crack-X, shrink-free or equivalent all as per manufacturer's instructions and finishing the surfaces to match with existing finish complete all as specified and as directed by Engineer-in-Charge.

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 1,17,589.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

Vishal Builders

Parmatma Enterprises