SPECIAL REPAIR TO BUILDING NO T-28 (OFFICE COMPLEX) AND T-30 (CO OFFICE) AT OD COMPLEX UNDER GE (EAST) MATHURA

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate as in levelling course for flooring complete all as specified and directed.

M&L for Non Skid ceramic coloured tiles 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

M&L for Vitrified Ceramic light shade tiles 10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

All as per item serial No 4.00 here-in-before but as on vertical surfaces laid over and including 10 mm thick rendering in cement motar 1:3 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface of size 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick rendering in cement motar 1:3 complete all as specified and as directed.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and as directed.

M&L for Brick work using old size fly ash Bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in coping, benching, flooring/hard standing/side kerb etc complete all as specified and as directed.

Taking down cement plaster on brick walls and concrete surface including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 finished even & fair complete all as specified and as directed.

M&L for preparation of newly plastered surface of walls providing 1mm thick wall care putty and applying two coat of oil bound distemper over and including a coat of alklai resitant primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coat of cement base paint white or tinted over and including a coat of primer complete all as specified and as directed.

Demolition of stone slabs of any description or thickness in floors/apron etc laid bedded and pointed in any mortar complete all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps jambs, pillar, window cills, cooking platform and like laid over and including 10mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2) using marbal dust with admixture of pigment to match the shade of granite complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 15 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

Supplying & fixing steel tubing ,galvanised, medium grade 20 mm bore with all fittings and fixed complete to walls and ceiling or laid under floor complete all as specified and as directed.

S&F in repair bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for 15 mm bore dia pipes or union complete all as specified and as directed.

S&F in repair angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both ends for 15 mm bore dia pipes or union complete all as specified and as directed.

S&F stainless steel Grating doom 100 mm dia with or without hole complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nut of length 600mm complete as specified and as directed.

S&F in repairs vitreous china wash hand basin, white, flat back, size 550x400mm including brackets, brass, chromium plated waste coupling complete all as specified and as directed.

S&F in repair pillar tap cast copper alloy chromium plated, fancy type with capstan heads,screwed down high pressure,with or without letters Hot or Cold with long screwed shank and fly -nuts, screwed for iron pipe 15 mm bore dia complete all as specified and as directed.

S&F in repairs sheet glass assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stainless steel bracket guard and railing 60 cm long complete all as specified and directed.

S&F in repairs PVC valveless syphonic action type, low level flushing cistern 10 liter capacity white/coloured with inlet ball valve float and duel flushing button system handle including fixing brackets and 32mm bore PVC Flush pipe etc complete all as specified and as directed.

S&F Vitreous China bowl urinal flat back, white of size 465 x 355 x 265 mm, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including angle back of size 430 x 370 x 340 mm and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and as directed.

S&F in repairs white Vitreous china wash down water closet (pedestal pattern) with fixing bolt, Plastic water closet seat cover, white, closed pattern with flat bottom, and cover with mild steel chromium plated aluminised hinging device, complete all specified and as directed.

S&F in repair stainless steel Towel Rail 600 mm long , 20mm dia complete all as specified and directed

S&F in repair cast copper alloy Chromium plated swivel shower rose 125mm size with 450mm long arm complete all as specified and as directed.

S&F in repair Hand jet health faucet having 8mm dia & 1.2 mtr long SS flexible tube and wall hook with all connected fittings for 15mm bore pipe or union complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames not exc. 1.5 sqm each complete all as specified and as directed.

Taking down Chowkhats or frames with shutter without taking off shutters from the frames exc. 1.5 sqm but n exc 4 Sqm each complete all as specified and as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for door windows, ventilators (sliding, fixed or casement) with one or more rebates including joining cleat for fixing etc,complete all as specified and as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium work for partition using aluminium section with grove of size 63.5x38.10x2mm thick as in frame (square/rectangular) MS angle 65x65x6mm and 150mm long shall be fixed at bottom of vertical members with dash fastener/screws and MS angle is embedded in cement concrete 1:2:4 type B1 bolck size 150x150x150mm including providing 5mm thick tinted glass and 20mm thick pre laminated particle board in ratio of 50-50 fixed in grove of aluminium frame including all necessary accessories fittings etc complete all as specified and as directed.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and as directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370). Note:- Section No given above are of make Jindal, Contractor may use similar section of other make mention in make list.

S&F 5mm thick, Sheet glass ordinary quality and glazing with aluminium beading n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5 mm thick plain colur PVC sheet one side pre-maminated reinforced with MS square tube supplying and fixing in opening complete all as specified and as directed.

S&F factory made Solid PVC Moulded Door Shutter 28 to 30mm thick (stiles) with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site complete all as specified and as directed.

S&F 150mm size aluminium handles fabricated type anodised complete all as specified and as directed.

S&F aluminium anodized barrel tower bolts 200 mm length of bolt of extruded section and fixed complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts 250 mm long of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F in repair PVC (SWR) 110mm bore bends any radius with oval access door complete as specified and as directed.

S&F in repair PVC (SWR) floor trap plain 100mm dia of outlet with grating including jointing with solvent cement complete as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including ridges, hips, valleys etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as in ridges/valley gutters, fixed with self tapping screws complete all as specified and as directed.

Dismantling timber scantlings (framed work) exc 40 Sq cm in section in any position complete all as specified and as directed.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240 complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over and including a coat of red oxide primer complete as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed .

M&L for providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint for all hights complete all as specified and as directed.

M&L for 4 mm thick non-asbestos fibre cement building board having fire resistance & moisture resistance properties and fixed in ceiling complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tank (Triple layers white in colour) (Cylindrical vertical with close top) 750 liters capacity having monkey protection cover hoisted and fixed in position on roof including connections and ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore dia iron pipe complete all as specified and as directed.

S&F in repair Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes 20 mm bore dia complete all as specified and as directed.

Excavation in trenches in not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for foundations, laying of cables etc and getting out as in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, levelling, watering and well ramming excavated soil in layers not exceeding 25 cm thick complete all as specified and as directed.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Demolition and breaking up 150 mm internal dia drain pipe (salt glazed ware, AC or reinforced cement concrete) set in cement mortar including cement concrete bedding and haunching and removing the demolished material out of MoD land complete all as specified and as directed.

M&L for Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm internal dia pipe complete all as specified and as directed.

M&L salt glazed stone ware drain pipe 150 mm bore internal dia grade 'A' laid in trenches and jointed with cement mortar 1:1 complete all as specified and as directed.

Construction of Soakage well of 1.80 mtr dia and 3.0 mtr deep complete all as specified and as shown in drawing No CEJZ/2004/S-35 sheet 1/1 dated 11 May 2004 (Revised 06-08-2005) which includes the following:- (i) Excavation and earth work, including R/F and removal of surplus soil. (ii) Cement concrete in foundation, brick work honey comb brick work. (iii) Reinforced cement concrete, form work, reinforcement (iv) Precast cover slab, plastering, filling brick agreggate and all Pipes and fitting complete all as shown on drawing as specified and as directed.

M&L for 50 mm thick cement concrete type C-1 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth (using extra cement) compete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (Below or above ground level) including removal of debris outside of MOD land complete all as specified and as directed.

M&L for sand cushioning 25 mm thick spread and levelled over PCC sub base complete all as specified and as directed.

M&L 100 mm thick cement concrete 1:4:8 type D2 (using 40 mm graded aggregate) as in sub floors, sub bases, floors and paving etc. complete all as specified and as directed.

M&L machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658-2006 of 80mm thickness M-40 grade of concrete as in floors/pavements complete all as specified and as directed.

M&L rendering 15mm thick on other than fair face of brick work or concrete surface in cement mortar 1:4 mixed with liquid water proofing compound as per manufacturers instructions finished even & fair complete all as specified and as directed. Note :- Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in cement morter 1:4 and finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

S&F stainless steel Butt hinges 100mm of extruded section and fixed complete all as specified and as directed.

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc.) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as specified and as directed.

Taking down carefully by Submain wiring of any type making good the disturbed surface to match with existing surface complete all as specified and as directed.

Taking down old unserviceable existing SPN/TPN DB/enclousers any size and type/any descriptions as iron sheet scrap including MCB any type/size and making good disturbed surface/wall as per existing complete all as specified and directed.

M&L for Point wiring complete with 1.5 Sqmm single core PVC insulated (FRLS) cable 1100 volts grade with multi-stranded, copper conductor drawn through and including 20mm dia rigid non-metallic PVC conduit with all acessories such as internal bend end caps etc complete concealed in wall including necessary cutting chases and making good disturbed sufrace to match the existing surface including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistrandered copper conductor cable as earth continuity conductor, fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls with 3mm thick bakelite top cover sheet ISI marked with chrominium plated screws and cup washers for housing the switches, socket outlets fan regulators etc complete all as specified and as directed the followngs:-

One light/fan/exhaust fan point controlled by one way switch 5 amp complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on same board complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on independent board complete all as specified and as directed.

All as per item No. 81.00 here-in-above but for 3 pin /5 pin 16Amps socket point controlled independently, with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed.

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified and as directed.

Supply and Fixing Modular switch 16 Amp single pole one way,1 Module complete all as specified and as directed.

Supply & Fixing Modular fan Regulator electronic step type 2M complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified and as directed.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified and as directed.

S&F ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and as directed.

S&F modular white cover plate with frame, 1 module complete all as specified and as directed.

S&F modular white cover plate with frame, 3 module complete all as specified and as directed.

S&F modular white cover plate with frame, 4 module complete all as specified and as directed.

S&F modular white cover plate with frame, 6 module complete all as specified and as directed.

S&F modular white cover plate with frame, 8 module complete all as specified and as directed.

S&F Modular metal flush box 1/2 Module complete all as specified and as directed.

S&F Modular metal flush box 3 Module complete all as specified and as directed.

S&F Modular metal flush box 4 Module complete all as specified and as directed.

S&F Modular metal flush box 6 Module complete all as specified and as directed.

S&F Modular metal flush box 8 Module complete all as specified and as directed.

S&F indoor decorative ultra slim surface/Wall mounted LED batten tube light fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired with and including 1 x 20 watt LED tube and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F intergrated Batten PC housing extruded T5 LED batten tube 2' light fitting complete with all accessories internally pre-wired with and including 1X9 watt LED Tube connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F of 30W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V with and including 30W LED tube all connections complete all as specified and as directed.

S&F for building security light bracket made out of 40mm dia medium grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including applying two coats of aluminium paint over a coating of red oxide primer complete all as specified and as directed.

Taking down the ceiling fan/Exhuast fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearings, reassembling the fan and blades, painting of fans with synthetic enamel paint by spraying a single coat as per existing colour paint including provision of 3 core twisted flexible copper conductor cable 0.75 Sqmm from ceiling rose to connector of fan, hanging/fixing the fan in its original position and testing on completion complete all as specified and as directed.

M&L for Sub Main Wiring with two runs single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases( making good all to the disturbed surfaces as per existing) with and including one run of 6sqmm copper green colour earth wire complete all as specified and as directed. Note: Two runs 6sqmm, one run of 6sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder coated with Copper bus-bar 250Amp, two neutral link, earth bar with provision for 63 Amps MCCB as incomer and SP/TP MCBs as outgoing, cable ties for cable management, 440 V, 4 way complete all as specified and as directed Note : - (i) MCB & MCB /MCCB DBs shall be of same make. DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as pe directed & rate shall be included in the items. (ii) MCB & MCB/MCCB DBs shall be measured and paid separtely under relevant items of this BOQ.

S&F sheet metal enclosure MCB distribution board, SPN 8 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail , cable ties for cable management, 240 V complete all as specified and as directed.

S&F SP enclosure with a two pin and earth plug and socket complete with SP MCB of rating 20-32 Amps, 240 Volts complete all as specified and as directed.

Supply and fixing MCCB 63 Amp rating, (Ics=100% Icu) 4-pole 415V, adjustable thermal and fixed megnetic type breaking capacity 16KA complete all as specified and as directed.

S&F in replacement MCB TP 40-63 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB DP 40-63 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

S&F MCB SP 6-32 Amps, 'B' series, breacking capacity 10KA, 240V complete all as specified and as directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor of size 35 Sqmm 3.5 core laid in trenches/duct/fixing on walls/poles including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole/Main Panel Box and testing complete all as specified and as directed.

M&L for clean dry Yamuna sand laid in trenches/ducts for bedding and cushioning to cable including spreading and levelling complete all as specified and as directed. Note : Punned thickness of sand shall only be measured for payment purpose.

Supply and Laying in trenches Unreinforced precast concrete cable cover class LV type 1, flat, size 250mmx150mmx40mm for cable protection cover complete all as specified and as directed.

M&L for laying steel tubing, light grade, galvanised, 40 mm bore with all fittings as cable protection fixed on walls/along poles/road crossing or laid in floor complete all as specified and as directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

S&F in replacement of recess mounting LED light fitting 2x2, square shape 24W, 230V complete with all accessories internally prewired and including connected up with twin core twisted flexible copper conductor cable with suitable sizes complete all as specified and as directed.

M&L for Sub Main Wiring with 4 runs single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor cable drawn in suitable size of rigid non-metallic PVC conduit (not less then 25mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases( making good all to the disturbed surfaces to match the existing surface with and including one run 6sqmm copper green colour earth wire complete all as specified and as directed. Note: Four runs of 6sqmm, one run of 6 sqmm earth wire & One run of PVC conduit shall be measured as one unit length.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder coated with Copper bus-bar 250Amp, two neutral link, earth bar with provision for 125Amps MCCB as incomer and SP/TP MCBs as outgoing, cable ties for cable management, 440 V, 4 way complete all as specified and as directed Note : - (i) MCB & MCB /MCCB DBs shall be of same make. DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as pe directed & rate shall be included in the items. (ii) MCB & MCB/MCCB DBs shall be measured and paid separtely under relevant items of this BOQ.

S&F sheet metal enclosure MCB distribution board, TPN 4 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail, cable ties for cable management, 240 V complete all as specified and as directed.

S&F sheet metal enclosure MCB distribution board, SPN 4 Way, Double door, phosphatised, powder coated with 200Amp rated bus-bar, neutral link, earth bar and din rail, cable ties for cable management, 240 V complete all as specified and as directed.

Supply and fixing MCCB 125Amp rating, (Ics=100% Icu) 4-pole 415V, adjustable thermal and fixed megnetic type, 'C' series, breaking capacity 16KA complete all as specified and as directed.

S&F MCB TPN 40-100 Amps, 'C' series, breacking capacity 10KA, 240V complete all as specified and as directed.

Supply, laying, jointing and testing of XLPE insulated, sheathed, armoured, heavy duty LT 1100 volts grade cable with aluminium conductor of size 50 Sqmm 3.5 core laid in trenches/duct/fixing on walls/poles including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole/Main Panel Box and testing complete all as specified and as directed.

M/S PREETI CONSTRUCTION

B S ENTERPRISES

M/S ANIL KUMAR

mh enterprises

KASHI NATH BANWARI LAL

M/s Hoti Lal Contractor

Ahmed constructions