REPAIR AND MAINT OF CERTAIN BR WORKS IN OTM ACCN OF HAWK HILL IN AGE BR II AREA UNDER GE SAUGOR

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises complete all as specified and directed

Demolition of cement concrete in ground floors and pavings not exc 15cm below or above ground floor complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) not exc 1.5 Sqm each complete all as specified and directed

Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but not exc 4 Sqm each complete all as specified and directed .

Taking down shutters of any description not exc 1 Sqm each complete all as specified and directed

Taking down shutters of any description exc 1sqm but not exc 2 Sqm each complete all as specified and directed

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion & making good disturbed ground embedded in Concrete, brick work, masonry, etc complete all as specified and directed

M&L for PCC type B2, 1:2:4 (using 40 mm graded stone aggregates) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks, straright or curved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work with all quoins arches , pillars etc built in cement mortar complete all as specified and directed.

All as per Srl item No 10 as above but except bricks. Note:-Serviceable bricks obtained from demolition shall be re-used in this item.

M&L for stone walling of random rubble, uncoursed well bonded, bedded and solidly hearted built in cement mortor 1:6 including demolition of rubbled stone masonry with all quoins arches , pillars etc built in cement mortar complete all as specified and directed

M&L for cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, in cement mortor 1:3 cutting not exceeding 10cm girth complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed..

M&L for mild steel TMT bars6mm to 8 mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed..

M&L for precast reinforced cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including demolition of RCC in precast cover slab any thicknes (reinforced) complete all as specified and directed.

M&L for providing precast cement concrete louvers and jallies 35 mm thick, type B-0, 1:2:4 (using 12.5mm graded stone aggregates) set in cement mortar (1:4), (Measured solid), including all mouldings including dismantling of existing jallies of any description complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed or beding layer in cement mortar (1:6) complete all as specified and directed.

M&L for coloured anti skid ceremic tiles 7 to 8 mm thick area of each tiles exc. 0.11 sqm and n. exc. 0.18 sqm (400mm x 400mm joint free (rectified) ) as in floor set & jointed in neat cement slurry and pointed in white /coloured cement to match the colour of tiles laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per Srl item No.19 above but in dado / skirting laid over and including 10mm thick rendering in CM(1:4) complete all as specified and directed..

M&L for coloured non skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed in CM(1:6) complete all as specified and directed.

All as per Srl item No. 21 above but in dado / skirting laid over and including 10mm thick rendering in CM (1:4)

M&L for coloured glazed ceramic tiles of size 600mm x 300mm x 7mm thick,(joint free (rectified)) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry and pointed in white/ coloured cement to match the colour of tiles laid over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for 600mm x 600mm x 8mm to 10 mm thick coloured vitrified tiles in floors set & jointed in neat cement slurry and pointed in white /coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per Srl item No. 24 above but in dado / skirting laid over and including 10mm thick rendering in CM (1:4) complete all as specified and directed.

M&L for mirror polished machine cut Kota stone slab flooring 18mm to 20mm thick laid over and including 15mm thick screed in CM(1:4) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L for Kota stone slab 12mm to15mm thick in skirting laid over and including 15mm thick plaster in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L for 16mm to18mm thick Granite slab of any shade ( table rubbed and polished ) in steps, jambs, pillars, windowcills, cooking plateforms and like in cement mortor 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match shade of the slabs complete all as specified and directed.

M&L for rounding/ chamferring to edges of stone slabss one edge , such as in steps , cooking plateform and other similar situations complete all as specified and directed.

M&L for coloured designer tiles exterior grade ( ENDURA or equivalent ) 10mm thick laid over and including 15 mm thick cement mortor 1:6 set and jointed in floor and pointed in neat cement slurry with grey cement and pigment in floor complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver blocks glossy finished chemically treated any shape and size confirming to IS-15658-2006 size of 60 mm thickness, M-35 Grade with grey cement and pigment including 40mm stone dust cushioning complete all as specified and directed.

M&L for 40mm thick PCC type B-0, 1:2:4 (using 12.5mm graded stone aggregates) surface finished even & smooth using extra cement complete all as specified and directed

S&F glass dividing strips, 3mm thick & inserted in position to confirm to design width of strip 38 mm complete all as specified and directed.

M&L for cement concrete 1:3:6, type C2 (using 40mm graded stone aggregates) as in plinth protection 75mm thick finishing cement concrete surfaces even & smooth without using extra cement including filling of joints with bituminous sealing compound complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in sub base of floor to receive tiles or Kota stone complete all as specified and directed.

M&L for 75mm thick PCC type C2, 1:3:6 (using 40mm graded stone aggregates) as in mass concrete filling complete all as specified and directed.

M&L for rendering 20 mm thick cement plaster in cement mortar 1:6 on stone masonary / other than fair finished surfaces of brick wall finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick cement plaster on wall in cement mortar 1:6 on brick wall / concrete surfaces of finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) including water proofing compound @ 2% by wt of cement complete all as specified and directed..

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed.

M&L for applying three coats of white wash on new ceiling surface including preparation of surfaces complete all as specified and directed..

M&L for applying two coats of synthetic distemper white or tinted on new wall surface including preparation of surfaces complete all as specified and directed..

M&L for applying two coats of synthetic distemper white or tinted on old wall surface including preparation of surfaces complete all as specified and directed..

M&L for two coat of exterior emulsion anti fungal paint over one coat of primer on newly plastered surface of walls including preparation of surfaces complete all as specified and directed.

S&F GI ( cold rolled) snap grid size of 600mm x 600 mm frame work of 24 x 38 x 0.60 mm, Tee Section ( bottom pre coated ) and 24 x 24 x 0.5 mm thick angle rung along the wall incl GI suspenders wire as per manufacturer instruction as in ceiling with and including S & F coloured Non Asbestos designer ceiling cement boards 4 mm thick including dismantling textile coverings including frames (if any) & cover fillets in ceilings (measured flat & not girthed) complete all as specified and directed

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated shets in roofs fixed with L-type or J-type or cranked hook bolts including dismantling of old asbestos cement (corrugated,semicorrugated etc) sheets in roof covering complete all as specified and directed

All as per Srl item No.46 as above but except sheets -ditto- Note:-Serviceable AC sheets from dismantling shall be re-used in this item.

S&F 6mm thick asbestos cement serrated ridge or hip ridge for corugated or semi corugated sheets, fixed with L-type or J-type or cranked hook bolts complete all as specified and directed including dismantling existing damaged AC sheet ridge/hip for corrugated or semi corrugated sheets from roof and taking down carefuly etc.

M&L for second class hardwood in scantlings timber clean sawn framed and fixed including dismantling unframed timber scantlings 40 sqcm & over in section, in any position complete all as specified and directed

M&L for second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed

S&F 105 mm X 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of red oxide primer including cutting holes and making good in PCC 1.2.4 type B1 (using 20 mm graded stone aggregates) including PCC 1:3:6 type C0 (using 12.5mm graded stone aggregates) for filling in pressed steel frame complete all as specified and directed

S&F 125 mm X 60 mm size pressed steel frames for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of red oxide primer including cutting holes and making good in PCC 1.2.4 type B1 (using 20 mm graded stone aggregates) including PCC 1:3:6 type C0 (using 12.5mm graded stone aggregates) for filling in pressed steel frame complete all as specified and directed

S&F mild steel door shutter with MS angle iron shutters frame 35 mm X 35 mm X 5 mm in two panel covered with 1.25 mm thick MS plain black sheet welded to shutter with 2 Nos sliding door bolt of 16 mm dia 300 mm long with locking arrangement, 2 Nos of tower bolt of 200 mm longincluding MS angle iron frame 40mm x40mmx 5mm as in chowkhat with 6 Nos hold fast of flat iron 30mm X5 mm ,200 mm long with bottom flat iron of size 30mmx5mm and 100 mm size 4 Nos butt hinges including necessary cutting, welding, binding as required with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces complete all as specified and as directed. [Single shutters of approx width0.8 to 1.2 m and ht 1.9 to 2.10 M.]

S&F steel window with side hung shutters with glazing bars devetailed or welded, fixed on and including pressed steel frame of size 80mm x 40mm x 1.25mm thick CRCA profile section with box hinges, steel handle, steel peg stay etc including PCC 1:3:6, type C0 (using 12.5mm graded stone aggregates) for filling in pressed steel frame complete all as specified and directed.

S&F steel window with side hund shutters without glazing bars and fixed to steel frame complete all as specified and directed.

S&F fixed type ventilators aluminium powder coated of frame size 50.80X 25.40mm,1.3 mm thick half portion will be fixed with 4mm thick frosted glass and half portion will be fixed with louvers with 4mm thick frosted glass with rubber gasket and aluminium beading ,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.45 mm dia to be fixed over louvers portion only including necessary cutting holes on wall and fixing arrangements complete all as specified and directed. (Note:-Aluminium section thickness shall be1.50 mm)

S&F partly glazed (5.0 mm thick plain / coloured glass) aluminum door in repairs powder coated consisting of frame of 63.50 mm x 38.10 mm size with shutter fixed on frame both side open able on pivotal arrangement with including necessary cutting holes in wall & floor, Door shutter consists of top and bottom rail size is 83 x 44.45 mm , & lock rail size is 100 x 44.45 mm & style of door shutter is 85mmx 44.45 mm with handles 2 Nos in each door , hinges has fitted on frame as required fixed with rubber gasket & aluminum beading any No of panels with aluminum handle , locking arrangemen,floor door stopper including necessary joining cleats , glazing clips and floor springs etc complete, confirming to IS Make - Jindal Aluminum / Man Industries or equivalent as approved by GE. Note:-Thickness of Aluminium Section shall be 2.00 mm)

S&F aluminium windows sliding type three track powder coated consisting of frame bottom with gutter of size min 92.34 X 39 mm,sideand top of size min 92.34X29.70, shutters vertical 39X20 mm,shutter top &bottom of size min 20X39 mm ,shutter interlock min size 39X20 mm with rollers and conceled locking arrangements with 4 mm thick tinted glass with rubber gasket,brush and aluminium beading , ,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.45 mm dia etc including necessary cutting holes on wall and floor and confirming to IS complete all as specified and directed. (Note:-Aluminium section thicknessshall be 1.50 mm)

S&F 35mm thick second class hardwood factory made plain framed, penelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces complete all as specified and directed. Note:- The size of rail and stile as per : IS 1003 (part I), kiln seasoned and chemically pressure treated.

S&F 35 mm thick flush shutters, solid core construction, with block board core and plywood facepanels, commercial type on both sides, complete all as specified and directed(with double or single shutter complete all as specified and directed..

S&F second class ardwood factory made glazed and skeleton shutters 35 mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F second class hardwood factory made 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (with sash bars any numbers), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, for windows and ventilator all as per SSR Part-I clause 8.24 (b) complete all as specified and directed.

S&F 30mm thick second class hardwood factory made glazed and skeleton shutters , open rebated and prepared to receive glass, guaze, etc.(without sash bars), edges of framing plain chamfered or rounded fitted with cut and metered beads for securing glass etc . size of members of shutters as specified in SSR-I , section-8, clause-8.24(b) for windows and ventilator complete all as specified and directed..

S&F factory made Solid PVC prelam door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet single side prelam PVC sheet wood grain printed used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with mild steel square tube complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6mm raised panel design with 4mm thick moulded PVC sheet prelam on the front face & 4mm prelam PVC sheet on back face, supplying & fixing in frame centre core will be PVC batten complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth, 0.46 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F second class hard wood beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc and removing old beads complete all as specified and directed..

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer complete all as specified and directed.

S&F mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed, length of bolt 200mm complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed..

S&F Mild steel barrel tower blots 100mm long, stove enamelled black, with bright bolt complete all as specified and directed..

S&F Mild steel pressed handles,150mm oval type, stove enamelled black complete all as specified and directed.

S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long dia not less then 12 mm with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed..

S&F mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, length of bolt 300 mm . complete all as specified and directed.

S&F Butt hinges of 100 mm size, Medium weight, cold rolled mild steel and fixed complete all as specified and directed.

S&F 100mm Butt hinges, extruded aluminium aloy with galvanised mild steel hinge pin, anodised and fixed complete all as specified and directed.

S&F 75mm size butt hinges medium weught , cold rolled MS and fixed complete all as specified and directed..

S&F door stopper of aluminium alloy body and tongue 150 mm long , anodised fixed in door with screws complete all as specified and directed.

S&F 250 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for PCC 1:3:6, type C1 (using 20mm graded stone aggregates) as in filling of hold fast etc, complete all as specified and directed.

M&L for cutting holes in brick walls in cement mortar or cement lime mortar and stone wall built in lime mortar for inserting holdfasts in exceeding one brick but not exc. two brick wall and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B1 as required complete all as specified and directed..

M&L for preparing surface of wood & wood based materials, steel & iron work, new or old, of any description & girth, not otherwise described & treated with tar or coal tar black paint complete all as specified and directed.

All as per Srl item No. 86 as above but treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc area not exc 0.1 Sqm each complete all as specified and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples, chains, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters;and similar small articles conforming to Fe 290, Gde E 165 complete all as specified and directed.

S&F framed work such as grills gratings, sunshed cover fixed with nut bolts incl,cutting drilling holes etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed baluster, walk ways, railings, framedwork or water tanks and similar work conforming to Fe 290, Gde E 165 complete all as specified and directed.

S&F mild steel for wind ties for roof including securing bolts, posts including all necessary drilling, bolting or riveting, etc & similar work conforming to Fe 290-0, Gde E-165 complete all as specified and directed..

S&F for steel work in tubular trusses or post, purlin and rafters, etc using tubes, pipes, hollow section complete all as specified and directed.

Hacking out old broken glass (any tickness, size,quality or description) from wooden / steel framesglazed with oil putty or fixed with beads complete all as specified and directed.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F for 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed..

S&F in repairs 110mm bore PVC(SWR) pipes single soketed in any length with adhesive jointed fixed to wall including mild steel clamps complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm bore single socketed, in any length with adhesive joints laid in trenches or in floors complete all as specified and directed.

S&F in repairs PVC (SWR) bends 110 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) 110 mm bore junction, single(single 'T') equal or unequal complete all as specified and directed .

S&F in repair PVC(SWR) vent cowl of 110mm dia complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 75mm bore single socketed, in any length with adhesive joints laid in trenches or in floors complete all as specified and directed..

S&F PVC (SWR) pipes 75mm bore single socketed in any length with adhesive joints fixed to walls complete all as specified and directed.

S&F in repairs PVC (SWR) bends 75mm bore complete all as specified and directed.

S&F in repair PVC(SWR) vent cowl of 75mm dia complete all as specified and directed.

S&F in repairs for 75 mm dia PVC ( SWR) floor trap with grating including jointing with solvent complete all as specified and directed.

S&F in repairs 25 mm dia aluminium powder coated droppery rod including brackets complete all as specified and directed.

S&F GI tubing 15 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down 15 mm dia GI tubing and connection complete all as specified and directed. .

S&F GI tubing 20 mm bore medium grade with all fittings fixed to walls and ceilings or laid in floors including taking down 20 mm dia GI tubing and connection complete all as specified and directed. .

M&L for cutting existing steel tubing for alterations or additions (Each cut measured) 15mm /20 mm pipe complete all as specified and directed.

M&L for screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) 15mm/20mm pipe complete all as specified and directed.

S&F in repair PVC float valve assembly including assessories with float valve 20mm dia complete all as specified and directed.

S&F in repair soap dish brass chromium plated fixed to wall with brass chromium plated screw and wooden/ plastic plug complete all as specified and directed.

S&F in repair CP bib taps, cast copper alloy fancy concealed type with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm bore complete all as specified and directed.

S&F in repair angular stop valve , 15mm dia, cast copper alloy,CP fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair concealed stop valve , 15mm dia, cast copper alloy,CP fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions complete all as specified and directed.

S&F in repair Gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed..

S&F in repair bib tap standard of PTMT any colour high pressure screwed for iron pipe of 15 mm bore and fixed (Minimum weight 15mm 90gm) complete all as specified and directed.

S&F in repair pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F in repairs PTMT PVC grating of 100 mm dia complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repair vitreous China WHB white flat back size 550mmx400mm including S&F angle iron brackets, C.P pillar tap fency type 01 No 15mm bore, CP waste coupling, 32mm dia and PVC waste pipe 32mm dia and PVC connection 450mm long high pressure complete all as specified & directed.

S&F in repair vitreous China squatting pan 'Orrisa pattern' size 580x440mm white with integral foot rests any pattern including provn of cement concrete bedding and making connection with & including 'P' or 'S' trap complete all as specified and directed.

S&F in repair vitreous China wash down water closet pan (pedestal pattern), white including white seat cover complete all as specified and directed.

S&F in repair Brass CP bottle traps 40mm bore for wash basins with inlet & outlet screwed for pipe or connections including necessary packing, union & cap complete all as specified and directed.

S&F in repairs vitreous China bowl urinal angle back of size 430mm x 370mm x 340 mm white (min.), with grating & union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) complete all as specified and directed

S&F in repair PVC low level flushing cistern of 10 Ltr capacity including flushing pipe, PVC bend etc. complete all as specified and directed.

S&F in repair 125 mm size brass chormium plated shower rose including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered wall construction hoisted & fixed in position 1000 Ltrs capacity including dismantling water tanks of capacity not exc 1000 Ltrs complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layered wall construction hoisted & fixed in position 500 Ltrs capacity including dismantling water tanks of capacity not exc 500 Ltrs complete all as specified and directed.

S& F in repairs glazed 12 mm thick toughened glass with frosted film on both sides of glass incl. necessary joining cleats and fixing it to walls with all necessary fixing arrangements , glazing clips etc complete all as specified and directed.

S&F in repairs glazed 12 mm thick toughened glass with frosted film on both sides of glass as in sliding door with all necessary jointing cleats and all necessary stainless steel fitments complete all as specified and directed

Taking down copper/aluminum pt wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting ,wooden boards, bell push, call bell,MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor complete all as specified and directed.

Taking down main switch, DB/TPN , AC box of any capacity complete all as specified and directed..

M&L for concealed point wiring with 1.5 Sqmm PVC(FR) insulated, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc/square TW Mica Top blocks at junction for batten holders, ceiling rose etc screws, gutti/roul plugs PVC all as per site requirement including MS sunken boxes made out of ms sheet and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green complete all as specified and directed (Make:–for cable - Havells/Polycab/Finolex):-

For one light, fan point controlled by one switch

For one 5 Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

All as per Srl item No 134 here in before but for power point wiring using with 2.5 sqmm PVC (FR)insulated , unsheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,unsheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and colour coding of cables such as Phase-Red, Neutral-Black and Earth-Green.

M&L for point wiring with 1.5 Sqmm PVC insulated FR, unsheathed, copper conductor stranded 1100 volt grade cable in & incl PVC trunking of size not less than 20mm ISI marked ivory white with all accessories such as tee, bend, joint cover including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.6 mm with earth dolly and PVC laminated hylem/Anchor ISI marked top cover 3.0 mm thick for mounting of switches/sockets/ regulator etc and PVC insulated & unsheathed 1100 volt grade copper conductor, stranded 1.5 sqmm. cable as continuous earth lead complete all as specified and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as specified and directed (Make of wire: – Havells/Polycab/Finolex):-

For one light point or fan point controlled by one switch

For 5Amp independent socket point controlled by one switch

For one 3 pin ,5 Amp socket point with other switch on the same board

All as per Srl item No 136 here-in-before but for power point wiring with 2.5 Sqmm PVC-FR insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

S&F switch piano type flush, single pole, one way, 5 Amp 230 Volt complete all as specified and directed. Make:-Plaza octa series/Anchor Penta White Deluxe/ Havells

S&F socket outlet , 5 pin, 5 Amp flush, 230 Volt complete all as specified and directed.. Make:-Plaza octa series/Anchor Penta White Deluxe/ Havells

S&F switch piano type flush, single pole, one way,15 Amp 230 Volt complete all as specified and directed. Make:-Plaza octa series/Anchor Penta White Deluxe/ Havells

S&F socket outlet 2 in 1, 6 pin, 5/15 Amp , flush type universal shuttered 230 Volt complete all as specified and directed. Make:-Plaza octa series/Anchor Penta White Deluxe/ Havells

S&F ceiling rose, surface backlit, 63.5x48 mm three terminal complete all as specified and directed. Make:-Plaza octa series/Anchor Penta White Deluxe/ Havells

S&F lamp holder pvc insulated with back plate suitable for Angle/Batten fitting with 9 Watt LED bulb complete all as specified and directed. Make:-Plaza octa series/Havells Reo/Anchor

S&F testing and commissioning of MCB SP 6-32 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified and directed. Make:- Legrand/Merlin garin /Schnieder/Havells

All as per Srl item No.144 above but SPN 32- 63 Amps, 240 V

S&F sheet metal enclosure for DB double door, IP-43 when MCBs to be used SPN, 8 way, 240 V with 200 Amps rated bus bar incl TW board of suitable size complete all as specified and directed.. Make:- Legrand/ L&T/Havells

S&F double door metallic sheet metal enclosure for DB double door(IP-42/43) When MCBs to be used SPN 4 ways, 240 V with 200Amps rated bus bar complete all as specified and directed. Make:- Havells/Legrand/ L&T

S&F electronic double space rotary step type 5 speed regulator 120- 280 V complete all as specified and directed. Make:- Plaza octa series/Anchor Penta White Deluxe/Havells

S&F LED TL fitting 20 watt for surface and wall mounted LED batten with ultra slim polycarbonate LED lighting fixture with high lumen output environmental friendly energy efficient complete all as specified and directed. Make:- Havells Cat Part N0 LHEXACP7IN1W020 LED 6500K 4 feet or eqvt in Phillips/CG.

S&F box type LED optic fitting 1x9 Watt 2 feet box type complete all as specified and directed. Make:-Havellls /Wipro/CG

S&F LED Bulk head 13 watt designed for modern homes availave in PIR as well as non PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer complete all as specified and directed. Make:-Havells Cat Part No LHEXCGP7UN5W013 /BAJAJ /CG.

M&L for concealed sub main wiring with 2 single core PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm (FR) drawn in and incl PVC rigid conduit medium grade of size not less than 20 mm dia ISI marked ivory white with all accessories such as tee, bend, joint cover etc PVC insulated, unsheathed copper conductor stranded 1100 volt grade cable of size 6 sqmm cable as continuous earth lead complete all as specified and directed .Make:– HAVELLS/FINOLEX/Polycab

M&L sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FR, 02 runs of 01 Single core of size 4 Sqmm (for main current) drawn in & incl PVC Casing-n-capping of suitable size ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 4 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green ccomplete all as specified and directed. Make:– HAVELLS/FINOLEX/Polycab

Taking down and refixing connecting of Ceiling fan after greasing complete all as specified and directed

m/s shivansh traders