Repair/Renewal of furniture at Military Station Abohar

Amount

TABLE 900 X 600mm with and without Drawer : Removing the exising UNSV top of table 3' X2' with / without drawer and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing of UNSV legs of table 3' X 2' with and without drawer and S&F of new legs as existing of Ist class hard wood .

Removing of UNSV long rails of table 3' X 2' with and without drawer and S&F of new long rails as existing of Ist class hard wood

Removing of UNSV side rails of table 3' X 2" with/without drawer S&F of new rail as existing of Ist class hard wood

Removing of UNSV drawer of table 3' X 2' with drawer and S &F new drawer as existing alongwith chromium plated knobs all as per drg.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

TABLE CENTRE : Removing the existing u/s top of table centre & S&F of new top of size 900x450mm made out of prelaminated (one side) particle board 18/19mm thick including 4mm thick TW beading around.

Removing of old u/s legs of table centre S&F of new legs as existing of Ist class hard wood

Removing of u/s long rail of table centre S&F of new rails as existing of Ist class hard wood

Removing of old u/s short rail of table centre and S&F new short rail made out of 1st class hard wood as shown in the drg

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain glossy finish on all the exposed surfaces.

TABLE BED SIDE (MAP) :Removing the existing u/s top of table bed side S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing of u/s side and replacing the same with one side teak faced prelaminated particle board

Removing the u/sdrawer and S&F new drawer made out of prelaminated partcile board and 12mm thick commercial plywood as specified in drg .

Removing the u/s back plywood , S&F new 6mm thick BWR grade plywood commercial as existing.

Removing the u/s legs and S&F new legs made out of ms square 18mm pipe with appropriate size screws and matching with black colour with other legs.

CHAIR DINING : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

All as per item No 17 but Rear legs

All as per item No 17 but Front rai

All as per item No 17 but Rear rail

All as per item No 17 but Side rail

All as per item No 17 but Back Wooden

All as per item No 17 but Stiffner

Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat and 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge. (For chair 0.40x0.39 = 0.156 Sqm)

Removing old u/s pvc seat from existing chair dining and S&F new PVC seat single piece 3mm thick weight not less than 0.39 Kgs with holes having 4 x 10mm thick ribs moulded all as specified in drg and as directed.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

CHAIR EASY : Removing the u/s front legs , S&F new front leg as existing of Ist class hard wood

All as per item No 27 but Arms

All as per item No 27 but Front rail

All as per item No 27 but Rear rail

All as per item No 27 but Side rail

All as per item No 27 but Top/Bottom rail Back frame

All as per item No 27 but Side rail back frame

Removing of existing cane cleaning of cane holes and recanning with 2 mm wide new plastic cane for seat 3.5 mm wide cane for borders of chair all as specified and shown on drg and as directed by Engr-in-charge. (For chair Seat 0.51x0.45=0.2295 Sqm) (Back 0.43x0.34=0.1462 Sqm) Total 0.3757 Sqm

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

PEG TABLE : Removing the existing u/s top of peg table , S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

All as per item No 36 but long rail

All as per item No 36 but short rail

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

TEAPOY : Removing the existing u/s top of Teapoy S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

All as per item No 41 but stiffner

All as per item No 41 but long rails

All as per item No 41 but short rails

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces.

SIDE BOARD : Removing of u/s back , S&F new back of side board with 6mm thick BWR grade commercial ply wood as existing and as per drg.

Removing the existing u/s shutter, S&F new shutter as existing made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The shutter shall be fixed with 4mm thick TW edging all round as per drg and fixed with aluminium anodised knob with ball spring catch.

Removing the u/s leg , S&F new leg as existing of Ist class hard wood

Removing of u/s drawers, S&F new drawers made out of 12mm commercial plywood and fixed with aluminium anodised knob all as per existing and shown on drg.

Removing of U/S shelves from side board and S&F new shelves as per existing shape & size made out of 18mm thick particle board one side teak faced.

Removing of U/S side of side board and S&F new side made out of 18 mm thick prelaminated particle board as per existing shape & size

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces including inside of shutter

TABLE DRESSING LADIES :Removing unsv back ply of mirror and S&F new 6mm commercial plywood to back of mirror as per existing shape and size as per drg

Removing unsv wooden member and S&F new TW member for holding mirror alongwith mirror frame alround as existing.

Removing unsv top of box and S&F new top made out of 19mm thick Prelaminated particle board one side teak shade to the top of table dressing ladies all as per drg with 4mm thick TW edging.

Removing unsv alluminium channel and S&F new 12x22mm Aluminium channel for sliding glass all as per drg

Removing unsv leg and S&F new leg as existing of Ist class hard wood

Removing unsv mirror and S&F new looking mirror of 5mm thick all as per drg and as existing

Removing unsv knob and S&F new aluminium anodised knob to drawer

Removing unsv drawer and S&F new drawer all as per existing size made out of 12mm thick commercial plywood.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

TABLE DINING 6 PERS : Removing the existing u/s top of Table and S&F new top made out of 18/19mm thick prelaminated particle board one side decorative teak shade and balancing white shade to the other side. The top shall be fixed with 4mm thick TW edging all round all as per drg.

Removing the unsv legs and S&F new legs as existing of Ist class hard wood

Removing the existing u/s top rail and S&F new rail as existing of Ist class hard wood

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

BED PLY WOOD TOP :Removing unsv plywood and beading of head board and S&F new teak veneered decorative plywood 4mm thick to both sides of the head board including fixing 6mm thick teak wood beading all round and as exising and as specified in drg .

Removing unsv plywood and beading of foot board and S&F new teak veneered decorative plywood 4mm thick to both sides of the foot board including fixing 6mm thick teak wood beading all round and as exising and as specified in drg .

Removing of unsv long rail & S&F new long rail made out of well seasoned teak wood as per existing shape & size

Removing of unsv support short rail and S&F new short suport rail made out of TW as existing and as per drg.

Removing of unsv legs and S&F new leg made out of well seasoned teak wood as per existing shape & size and as shown on drg.

Removing unsv ply wood top and S&F new ply wood 12mm thick commercial BWR grade with appropriate size MS screws 08 Nos as exising and as specified in drg

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces

SOFA SET 4 / 5 SEATER :

S&F cushion cover only of size 530x560x100mm cloth tapestry superior quality , colour, pattern and quality as approved by GE/Engr-in-Charge. Each cushion cover shall be provided with one side openable zip.

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces to sofa set 5 seater .

Preparing the old polished wooden surface for polishing with suitable sand paper & applying one coat of french polish to obtain a glossy finish on all the exposed surfaces to sofa set 4 seater

CHARPOY GI/IP: Removing of old unservicable existing elbows and S & F new GI elbowsThree way 32mm dia ISI Mark all as specified & directed

Removing of old unserviceable broken checknuts and S & F new GI check nuts for 32mm GI pipes ISI Marked all as specified & directed

Removing of existing unseviceable long rails from Charpoy GI pipe and S & F new long rails made out of GI pipe 32mm bore medium grade as per existing shape & size complete as specified & directed .

Removing exsting damaged short rails and fixing short rails to charpoy after conversion from retrieved old long rails duly threaded at both ends and fixing the same as per exsting shape & size complete all as directed .

Removing exsting damaged legs and fixing legs after conversion from retrieved old short rails duly threaded at one end and another side welding with 3mm thick MS sheet base and mild steel brackets of required size, shape for fixing MNF set all as shown on drawing and as directed .

M & L for welding to broken / cracked joints of charpoy GI pipe 32 mm dia (i.e) short rail, long rail, legs etc) by gas welding as per existing design rest all as specified and directed by Engineer-in-Charge.

Removing exsting unserviceable plywood from charpoy GI pipe and tightening entire frame and supply and fix 12mm thick plywood of BWR grade commercial of size 1980 x 900mm (Make : Archid /century /Greenply) fixed with flat head nut of size 5mm dia 60mm long, bolt with washer (Total 06 Nos per charpoy) including drilling holes in ply and steel frame of charpoy . Rest all as specified and directed by GE/Engr-in-Charge.

Chair Varandah : M & L for repair / fixing of broken parts of chair varandah by welding (Gas Welding) as existing with 20mm dia MS Conduite pipe where ever required as directed.

M & L for preparation of surfaces and painting of chair varandah with two coat of synthetic enamel paint white as specified and directed.

Removing of old exsting cane and recanning of chair varandah with new 4mm width 0.60mm thick cream colour plastic cane of approved quality as specified in drg and as directed.

Removing of old unserviceable PVC seat and back from chair varandah and S&F new PVC seat and back 4mm thick weight not less than 1.85 Kgs for both seat and back having 4 x 10mm thick ribs moulded complete all as specified and as directed by Engineer-in-Charge Make: Amko/Cello/Harmony

Supply and Fix new hard rubber shoes superior quality (as approved) of required size to chair varandah as directed.

REPAIRS TO CHAIR CB STEEL WITH ARMS AND WITHOUT ARMS: Removing of old unserviceable back frame of chair CB steel with arms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable seat frame of chair CB steel with arms and supply and fix new seat frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of seat duly welded and also making holes to seat frame centre to centre by drilling machine for fixing seat frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable hand rest and supply and fix new hand rest made out of well seasoned teakwood with required size screws. The hand rest shall be french polished with black colour all as specified, directed and as shown on drawing.

Removing of old unserviceable back frame of chair CB steel with out arms and supply and fix new back frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of back duly welded and also making holes to back frame centre to centre by drilling machine for fixing back frame with steel pipes by required size screws for extra support as directed.

Removing of old unserviceable seat frame of chair CB steel with out arms and supply and fix new seat frame made out of seasoned teakwood duly canned as per trade pattern. The chair shall be fixed with FI 3mm thick 14 X 25mm clips 02 Nos each on either side of seat duly welded and also making holes to seat frame centre to centre by drilling machine for fixing seat frame with steel pipes by required size screws for extra support as directed.

M & L for preparation of surfaces and painting of chair CB Steel With Arms with two coat of synthetic enamel paint Olive Green. All as specified and directed.

M & L for preparation of surfaces and painting of chair CB Steel With out Arms with two coat of synthetic enamel paint Olive Green. All as specified and directed.

ALMIRAH LARGE STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah Large steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah large steel. S&F new CP handle 150mm long as approved and directed.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

ALMIRAH MEDIUM STEEL WITH SHELVES: Removing unsv legs of almirah and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from almirah medium steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV 3 way locking device. S&F complete new locking device of same shape & size as existing and as per drg.

Removing of UNSV handle from almirah med steel. S&F new CP handle 150mm long of approved make.

Removing of old UNSV locks. S&F new brass lock 6 levers to almirah as approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

TABLE OFFICE OFFICER: Removing unsv top of table and S&F new top to table office officer steel made out of 18mm thick preleminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office Officer steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office Officer steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE OFFICE CLERK STEEL: Removing unsv top of table and S&F new top to table office clerk steel made out of 18mm thick prelaminated particle board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table office clerk steel and S&F new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Removing of UNSV locks from table office clerk steel and S&F of new brass locks of 6 lever with duplicate key of approved quality as approved by GE/Engr-in-Charge.

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as specified and directed by Engineer-in-charge

TABLE 3' X 2' WITH DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Removing of old UNSV drawers from table 3' x 2' steel and S&F of new drawers made of 1.00mm thick sheet of same shape & size as existing.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 2' WITH OUT DRAWER STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

TABLE 3' X 3' STEEL: Removing unsv top of table and S&F new top to table steel made out of 18mm thick prelaminated board exterior grade with 6mm thick teak wood beading edging alround the top.

Repairing frame of table with new 25mm square MS tube of 1.6 mm thick by arc welding where ever required as directed by Engr-in-Charge

Material & labour for painting to the frame of table with one coat of synthetic enamel paint olive Green all as per specified.

LOCKER BED SIDE STEEL : Removing unsv legs of locker and S&F new legs made out of 1mm thick MS sheet as existing by welding / revitting as per drg and as directed.

Removing of unsv shelves from locker bed side steel. S& F of new shelves made of 1.00mm thick MS sheet of same shape & size as existing

Removing of UNSV hasp and staple of locker and S&F new hasp and staple of same shape & size as existing and as per drg.

Removing of UNSV handle from locker bed side steel. S&F new steel handle 100mm long of approved make.

Removing of old UNSV hanging rod S&F new hanging rod CP of 20mm dia to locker approved .

M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed by Engr-in-Charge

CHAIR EXECUTIVE REVOLVING STEEL:

Removing old unsv seat of chair executive and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

Removing old unsv back of chair executive and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

Taking out old unsv castors wheel from executive chair and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

CHAIR WRITING STEEL:

(a) Taking out old unsv cantilever type MS frame from chair and S & F new cantilever type ms tubular frame made out of 25mm x 10mm sec as per existing size and shape complete all as specified and as directed by Engr-in-Charge

(b) Removing old unsv seat of chair steel and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(c) Removing old unsv back of chair steel and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

(d) Removing unsv armrest and S&F new one piece armrest made of black integral skin polyurethane with MS insert to the chair as existing with appropriate size bolt and nuts as specified and as directed.

CHAIR COMPUTER:

Removing old unsv seat of chair computer and S&F new seat made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

Removing old unsv back of chair computer and S&F new back made out of 12 mm thick hot pressed ply wood upholstered with fabric & moulded polyurethane foam with PVC lipping all around all as existing and as directed

Taking out old unsv castors wheel from chair computer and S & F new twin wheel castors as per existing size and shape complete all as specified and as directed by Engr-in-Charge

Removing unsv gas lift and S&F new gas lift of 100mm stroke length and gas pressure of 300n force as existing.

PAINTING OF STEEL FURNITURE: M & L for de-rusting, denting, scrapping, filling with putty including preparation of old steel surfaces and applying two coats of synthetic enamel paint of required colour internally and externally by spray painting complete all as specified and as directed :-

Side rack steel 3 spaces

Trestle store room steel

Rack steel 1830x760x1905mm

Rack 6 tier steel

Almirah Large Steel with shelf. All as shown on drg. MS Plane black sheet shall be of 1.00 mm thick. Shutter shall be fixed with steel chorimium plated handle six levers locking device keys in duplicate foe each Almirah. Lock shall be of Make Godrej or any equivalent with prior approval of GE. All exposed steel surfaces shall be spray painted with two coats of synthetic enamel olive green colour over a coat of red oxide primer. Shade of paint shall be as directed by the Engr-in-Charge.

Almirah Medium Steel. Over all size of the Almirah shall be as drawings. 1.00mm thick MS sheet shall be used for manufacturing the frame and shelf of the Almirah. Three way locking system shall be provide with shutters. 125mm long steel handle shall be provide with door leaf. All fitting/fixtures shall done accordance with standard works manship. All steel surfaces internal/external shall be painted with OG colour with two coat over a coat of primer with spray machine. Rest all as per drg.

Bed Hard 6'x3' steel in lieu of Bed hard with MNF Set. All as shown on drg. Pipe shall be of 25mm x 65 mm rectangular MS pipe (18 guage) Top shall be of 12mm thick BWR phenol bonded commercial ply (unpolished) places on top of 25 x 25mm supports. Middle supports shall be of 25 x 25 mm (18 guage) 04 Nos equal distance pipe in line with bottom of 25 x 65 mm section. Frame work of 38 x 38mm MS square pipe (18 guage) shall be used for frame of head rest & foot rest. All exposed wooden surfaces shall be frenched polished. The steel members shall be painted with two coats of synthetic enamel paint (in black) over a coat of red oxide primer. Rest all as per drg. Mattress & Pillow shall be as per the sample approved by GE.

Chair Dining (JCO/OR) . Overall size of the chair dining shall be as per drg. 1st class TW well seasoned shall be used for making the frame of chair. New PVC seat 3 mm thick PPCP 3 mm thick not less than 0.39 Kgs seat Make – AMCO, Cello, Comfo & Equitant shall be used. All fittings & fixture shall be done accordance with standard wk manship. All wooden surfaces exposed to view where placed in position shall be French polished to view where placed in position shall be French polished with high glossy finish. Rest all as per drg.

Chair executive medium back adjustable, in lieu of Chair revolving steel with arms. Chair executive medium back adjustable, Godrej, Model: DIXON 2 DIXON 2 LEATHERITE TAPESTRY

Chair Verandah . All as shown on drg. Over all size shall be 460mm long, 600mm wide and 760mm high legs shall made if 20mm dia mild steel conduit of wall thickness 1.6mm slanting 70mm horizontally for a vertical height of 355mm at front upto seat level. The horizontal distance between legs at seat level shall be 450mm and between bottom of legs shall be 600mm. The seat frame with back seat shall be of continuous 20mm dia mild steel. Conduit of wall thickness 1.6mm Cane plastic 4mm wide should be used in canning in Godrej Pattern PVC toes shall be provided to bottom of legs shown on drg. All steel surfaces exposed to view when placed in position shall be painted with two coats of white enamel painting over a coat of primer after preparation of surfaces as directed by engineer in charge.

Locker bed side Steel. 1.00 mm thick MS black sheet to be used for locker steel, shelves and portion to be provided as per drg. All joints /welding /fixing shall be done in accordance with the standard workmanship and specification. Shutters shall be provided with chorimium plated handle and 3 way locking device of Godrej pattern as approved by GE . All steel surfaces shall be spray printed with two coats of 1st quality synthetice enamel paint over a coat of red oxide primer internally /externally after preparation of surfaces as per drg as directed by Engr-in-charge, Note : The steel locker is not required to be fixed in the exisitning wall as shown on drg.

Table Bed side. Over all size shall be 550mm L x230mm W x 510mm H. Side, Top of table bed side shall be made cut of 19mm pre laminated particle board of Teak face. 6mm thick commercial ply wood shall be provided at back side and shelf shall be made out of 12mm thick commercial ply wood. 4mm thick TW edging shall be provided in the front of the sides. All wood & particle board surfaces exposed to view when placed in position shall be French polished in good look. Rest all as per drg.

Table Centre. All as shown on drg. All wood shall be of 1st class teak wood. Top shall be made of 19 mm thick pre-laminated particle board having one side in natural teak colour. All wood surfaces exposed to direct vision when placed in position shall be given high Frenchm polish. Hard rubber rings shall be screwed to the bottom of legs. Rest all as shown on drg.

Table Computer in lieu of Table office clk steel. All as shown on drg. 18mm thick pre-laminated particle board and 4mm thick teak wood beading duly polished must be used for making table computer 25mm square MS Pipe (18 gauge) shall be used where required. All frame work shall be of 1st class hard wood teak duly French polished surface of timber shall be French polished.

Chair Writing Map in lieu of Chair writing . All as shown on drg. Frame shall be made out of 25 x 10mm section MS tubular frame cantilever type powder coated. It shall be scratch and weather resistant. Both hand rest section to have slop towards front. Back foam shall be designed with contoured lumber support for extr comfort and 12 mm hot pressed plywood upholstered with fabric and moulded polyurethane foam with PVC lipping all round fabric shall be contained the following material in various colours Acrylic, polyester, poly, propylene.

N.R.Builders