SPL REPAIR TO BLDG NO. T-628 T-629 T-650 T-817 and T-820 INCLUDING REPLACEMENT OF EXISTING UNSERVICEABLE ASBESTOS SHEETS TO PPGI SHEETS IN THE AOR OF AGE BR-I UNDER GE A SURATGARH AT SURATGARH MIL STN

Amount

Dismantling asbestos cement corrugated or semi corrugated sheets as in roof covering complete all as specified and as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to all, th self tapping screws.tapping screws complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to ll, fixed with self tapping screws complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismentling unframed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and directed

M&L for steel work as in tubular/Square trusses, purlins, post including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 including painted with one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed by Engineer-in-charge

Taking down and erection Fixing only Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Note:- Refix the same rafter after raising ht. of bldg complete all as specified and as directed

M&L for preparation of new steel surfaces over 10cm in width or girth & applying two coats of synthetic enamel paint over a coat of red oxide zinc crome primer complete all as specified and as directed

M & L for preparation of old steel surfaces of any description not otherwise described over 10 CM width or girth and applying one coats of synthatic enamel paint complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and as directed.

M&L brickwork with fly ash bricks, straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks complete all as specified and directed by Engr-in-Charge.

All as per item No.11 here-in-above but except bricks all as specified .

Taking down cement or cement lime plaster wall and ceiling including in patches, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

M&L for rendering 15 mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of newly plastered surfaces of wall & applying two coats of Interior emulsion paint by Roller or Air Spray over 1 mm thick wall care putty (Multipurpose mixer shall be used for uniform and proper mixing of putty) complete all as specified and as directed by Engineer-in- charge.

M&L Complete removal of existing treatment and preparation of old decorated (platered or unplastered) of wall by Vacuum based sanding machine, removal of nails etc including filling of cracks and applying two coats of Interior emulsion paint by Roller or Air Spray incl over a layer of 1 mm or as required ( Multipurpose mixer shall be used for uniform and proper mixing of putty) of wall care putty, on plastered surfaces,prepara-tory to distempering complete all as specified & directed by Engineer -in-charge.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of newly plastred surfaces of wall,by Vaccume based sanding machine, and applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer by Auto Roller over 1 mm thick wall putty, including necessary scffoldings complte all as specified and as directed.

Material and labour for complete removal of existing treatment from old decorated plastered surfaces of wall by Vaccume based sanding machine, removal of nails etc & filling cracks/hole with putty, and finally washing with watering and applying two coats of exterior emulsion acyrlic weather proof antifungal paint over a coat of exterior grade primer by Auto Roller over 1 mm thick wall care putty, including necessary scffoldings complete all as specified and directed by Engr-in-Charge.

M & L providing cement concrete type B1 1:2:4(20 mm graded aggregate) as in lintels upto 1.5m clear span, copings, bed plates (block),cills, steps and other bands, parapet and railing upto 60cm height complete all as specified and directed .

Taking down Chowkats or frames exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as specified and directed .

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F Pressed steel frames 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed .

S & F Factory made single extruded WPC ( Wood polymer composite) Solid door/window or other frame /chowkets of size 45 mm x 70 mm compessing of virgin PVC polymer of k value 58-60 (suspension grade) calcium carbonate and natural fibre (eood powder /rice husk /wheet husk ) and non toxic additives (max. toxicity index of 12 for 100 grm ) fabricated with miter joint after applying pvc solvent cement and screwed with fully body threaded star headed ss screwed having min. frame dencity of 750 kg/cum screw withdrawal strenght of 2200 N(face) and 1100 N (edge) min. compessive strenght of 58 N/mm2 , modules of elasticity 900 n/mm2 and resistance to dpread of frame of class A cat. with property of being termite / borer proovf , water/ moisture proof and fire retardant and fixed in position with ms hold fast / lugs /ss dash fsterner of require dia and length complete all as per Engr in Charge.

S & F powder coated Aluminium anodised doors frame for doors, window/ventilators with one or more rebates including joining cleats for fixing complete complete all as specified and as directed.

S & F powder coated Aluminium anodised window and ventilators shutters side hung type without sash bars of aluminium section weighing 0.55 Kg/m including necessary joining cleats glazing clip, ruber neoprane packing, anodised aluminiun snap beading, screw anodised aluminium fitting such as peg stays 150mm long (01 Nos), hinge type B-21, 100 mm long (02Nos), suitable hadle and 100 mm long tower bolt, complete all as spd. & dierected.

M&L 4 mm thcik sheet glass ordinary,quality in squares exc 0.5 sqm each pane fixed to aluminium doors/ window/ventilator with beading & glazing clips complete all as specified & directed by Engr-in-Charge.

M & L Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staple staples complete allas per requirement complete all as specified and as directed

M&L Anodised aluminium silhouette snap grid with size of grid 605x605mm frame work for false ceiling incl. Hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and Providing and fixing PVC Gypsum Board 8 mm thick in ceiling fixed with screw as per manufacturers instructions including demolition of boarding, ceilling board with fram work complete all as specified.

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L Hard core of Broken bricks of gauze not exc 63 mm deposited spread and levelled in layers not exc 15cm thick watered and rammed to a true surface complete all as specified and as directed

M&L for 75 mm thick PCC (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in sub base, finished fair and even complete all as specified and directed by Engineer-in-charge.

M&L factory casted 60mm thick(Red/Yellow) machine pressed cement concrete interlocking (rubberised) paving blocks M-35 having compressive strength not less than 350 Kg / Sqcm using grey cement and no pigment and of shape hexagon/ triangular / zigzag / I-shaped / Three-X etc as directed conforming to IS 15658-2006, laid over & including 25mm thick sand cushion (local tibba sand), laid dry, joint filled with dry sand complete all as specified and directed by Engineer-in-Charge.

M& L for 50mm thick PCC 1:3:6 type C-1 (Using 20mm graded crushed stone aggregate) as in plinth protection finished even and fair without using extra cement complete all as specified and directed

Dismantling, floor, hearth or wall tiling including CM bedding (but not backing), removing rubbish off the premises complete all as specified and directed

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar (1:6) complete all as specified and directed by Engineer-in-charge.

M&L for non skid ceramic joint free coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) complete all as specified and directed by Engineer-in-charge.

M&L for Glazed ceramic tiles in vertical surface of 600x 300x 7 mm thick on vertical surface such as dado, skirting etc, set in tile adhesive conforming to IS-15477-2019 type-2 and thickness as per manufacturer instruction of approved make complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in any mortar complete all as specified and as directed.

M & L Granite (of any type) tiles 20mm thick in steps, jambs,pillers, window cill, cooking platform, etc machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and 15mm thick cement sand screed bed complete all as specified and as directed.

Taking down old unserviceable cooler stand of any size & any type fixed at cill level of windows at Ground & First Floor of building on external face of walls and making good the disturbed portion complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, cooler stand 12mm sq guard bar, framework of water tanks and similar works of quality Fe 290 (Gde E-165) etc complete all as specified and directed by Engineer-in-charge.

S&F as in repair stainless steel curtain rod (drapery rod), 25 mm dia fancy type with fixing brackets, stops, rollers, ends/finales etc complete all as specified

S&F of 20 mm outer dia CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings with all connected items in walls/ceiling or laying in floors including taking up or down 15mm bore steel tubing and connections with fittings such as stop cock bib cock etc including cleaning for refixing or removal complete all as specified and directed by Engineer-in-Charge

S&F of 25 mm outer dia CPVC pipes SDR 13.5 & Plain CPVC SDR 11 fittings with all connected items in walls/ceiling or laying in floors including taking up or down 20mm bore steel tubing and connections with fittings such as stop cock bib cock etc including cleaning for refixing or removal complete all as specified and directed by Engineer-in-Charge

M&L 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint complete jointed with adhesive fixed to walls/laid in trenches fixed with and including requisite Number of bend, single T, clamps made out of flat iron 25x4mm including Dismantling exisitng drain pipe, jointed in cement mortar and taking out of trenches, if required complete etc. (measured overall as fixed along the centre line over fitting and accessories) complete all as specified.and as directed by Engineer-in-charge.

M&L 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint complete jointed with adhesive fixed to walls/laid in trenches fixed with and including requisite Number of bend, single T, cross T, vent cowl, clamps made out of flat iron 25x4mm including Dismantling existing pipe and taking out of trenches, if required complete all as specified and as directed by Engineer-in-charge.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate complete all as specified and directed by Engineer-in-Charge.

S&F as in repair Vitreous China bowl urinal half stall white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) white including providing & fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with & including 60 mm long brass screws, pointing around urinal back in cement, with & including PTMT grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia inlcuding urinal spreader complete all as specified and directed by Engineer-in-charge.

S&F as in repairs countertop vitreous china wash basin white flat back size 550 x 400mm size excluding taps, waste chain and plug and porcelain stopper but including brackets and cutting for piinning in ends of brackets or cracking but inclusive of fixing of waste pipe.

S&F as in repair Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like duroplast seatcover, rag bolts, gel gasket etc. complete in all respect all as specified.

S&F as in repair10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as reqd complete all as specified and directed Engr-in-Charge.

S & F as in repair looking mirror 45 cm x 150 cm beveled edge mounted on 5 mm thick AC building board or commercial plywood and fixed to wooden plugs with CP brass complete all as specified and directed Engr-in-Charge.

S&F as in repair PVC connections 15mm size with PTMT nuts of length 600mm long complete all as specified and as directed

S&F as in repair grating doom CP 100mm dia of platedwith waste hole complete all as specified and as directed

S&F as in repair Towel Rail 600mm long of CP fixed with and including Chromium plated brass screws and wooden/plastic cleats.(Minimum weight 190gms) complete all as specified and as directed

S&F as in repair plantex platinum stainless steel 304 grade paper holder with mobile phone stand (chrome finish) complete all as specified and directed by Engineer-in-charge.

S&F as in repair chromium plated Soap dish holder including chromium plated brass screws and plastic cleats complete all as specified & directed by Engineer-in-Charge.

S&F as in repair hand faucet chromium plated complete all as specified and directed by Engineer-in-charge.

S&F as in repair 15mm dia bib taps, cast copper alloy fancy type chroimium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F as in repairs angle valves chrome plated fancy type 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-charge.

S&F as in repair Rotational moulded polyethylene water storage tanks white colour in tripple layers (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I (1000 Ltrs Capacity) including Ball brass valves 20 mm bore, high pressure,with polythene float & flynut complete, including Dismantling old water tanks

S&F as in repair 15mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including of all fitting complete all as specified & directed by Engineer-in-Charge.

S&F as in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including of all fitting complete all as specified & directed by Engineer-in-Charge.

Excavation in trenches n exc 1.5m wide and n exc1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in trenches incl spreading, levelling, watering, & well ramming in layers not exc 25cm thick complete all as specified and directed, in soil.

Removing excavated materials n.exc 50m & depositing where directed at a level n.exc 1.5m above from starting point complete all as specified in soil.

M&L PCC 1:3 :6 type D2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed

M&L PCC 1:2:4 type C-1 (using 20mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for PCC (1:2:4) type B1 (Using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed

Extra for forming fair finished drains & channels 30cm inner girth in cement concrete using extra cement including forms moulds etc complete all as specified and directed. (Inner girth only measured) complete all as specified and as directed

M&L for precast reinforced cement concrete type B1, 1:2:4 using 20mm graded stone aggregate in cover slabs (for manholes,soak/septic well etc), water (tank/drain) cover, shelves, landing and similar articles with plain faces incl necessary moulds and setting in CM 1:4 complete including demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-charge. Note :-(reinforcement shall be measured and paid separately)

M & L DWCPE (SN8) pipe 180 mm (OD) / 163 mm (ID) as per IS-16098 (Part-II) ( laid in trenches on bed to required shape including all necessary accessories/fitting / jointing/ rings, jointing and testing complete all as specified including 100 mm thick PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in concrete bed to drain/DWCPE pipes including forming cradles in after they are laid and tested complete for 180mm bore pipe and including demolition of sewage pipe all as specified and as directed.

Demolition of reinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L Providing precast reinforced ce-ment concrete(type B0 1:2:4,12.5mm graded concrete) in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in cement mortar 1:4 complete with joints to match all as specified and directed by Engr-in-Charge.

M&L Mild steel TMT steel reinforcement bars 10mm dia and over cut to length, bent to shape required incl cranking, hooking ends and binding with and including MS wire(annealed) not less than 0.9mm dia complete all as specified and directed.

Taking down carefully or drawn out from conduit, existing copper / aluminium point wiring for light, fan, bell, socket, power point etc complete including fixture and fittings such as switches, sockets, ceiling rose, pendent holder, light fittings, top sheet covers, fan regulators, MCB, DB, lamp, earth plug etc (excluding MS sunken boxes) and making good the disturbed surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge.

All as per serial item No.83 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on the same board with other switches.

All as per serial item No. 83 here-in-before but for One 3 pin 5 Amp socket outlet one light point controlled by one switch on independent board.

All as per Srl item No. 83 above, but wiring with cable of cross sectional area 4 Sqmm (nominal area) multi-stranded copper conductor FRLSH, PVC sheathed cable 1100 Volts shade for one switch socket combination 3 pin,15/16 Amps on independent board including 4 Sqmm PVC insulated multistranded unsheathed copper conductor wire as earth continuity to common earth dolly.

S&F Modular switch piano 6 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular switch piano 15/16 Amps single pole, one way, 01 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket 2 / 3 pin, 6 Amps, 230 volts, combined 2 Module complete all as specified and directed by Engineer-in-charge.

S&F Modular socket outlet 2/3 pin 06/16A, 6 pin,2 module, 230 Volts grade complete all as specified and directed by Engineer-in-charge.

S&F Modular electronic fan regulator suitable for ceiling fan 2 Module, 1200mm / 1400mm sweep, socket size, rotary type complete all as specified and directed by Engineer-in-charge.

S&F as in repair sheet metal plug & socket DB, SP, with a two pin and earth plug with socket, 230 Volts with & including one MCB SP ‘C’ Curve 10 kA, 20 Amps complete all as specified and directed by Engineer-in-charge.

S&F Lamp holder, insulated body with back plate etc complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose surface bakelite 65mmx50mm with two or three terminal complete all as specified and directed by Engineer-in-charge.

S&F as in repair flush mounting factory made SPN DB 8 way, 240 Volt, Double door, IP-54 protection, IK-09 with metal door with 100 Amps copper bus bar, with neutral bar, earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F as in repair flush mounting factory made TPN DB 4 way, 415 Volt, Double door, IP-54 protection, IK-09 with metal door with 200 Amps copper bus bar, with 02 neutral bar, 02 earth bar and cables ties for cable management fully insulated bus bar complete all as specified and directed by Engineer-in-charge.

S&F as in repair MCB 40-100 Amps, four pole, 415 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F as in repair MCB 40-63 Amps, SPN, 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F MCB 6 to 32 Amps, Single Pole 240 Volts, 10 KA, ‘C’ Curve, complete all as specified and directed by Engineer-in-charge.

S&F Energy efficient decorative ultra slim, prewired, lumiline 10 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W010/Crompton Cat Part CCS-103-10-65-SL-DP-NWH/Wipro Cat Part D531065 or equivalent cat part of Make as specified in Appendix "A".

S&F Energy efficient decorative ultra slim, prewired, lumiline 20 watt LED light fitting (Day cool light), batten type with drive & polycarbonate housing including tube rod and all accessories prewired fixed on wall / hanging complete all as specified and as directed by Engineer-in-charge. Make : Havells Cat Part No.:- LHEXAZP7PN1W020/Crompton Cat Part CCS-103-20-65-SL-DP-NWH/Wipro Cat Part D532065 or equivalent cat part of Make as specified in Appendix "A".

Supply and fixing LED lamp minimum 3 star rated 10W LED B-22 base complete all as specified and directed by Engr-in-Charge with following specifications (a) Lumen system efficacy of lamp should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 45°C (d) Power factor : Minimum 0.90 (e) CRI : Morethan 80

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

Supply, fixing and testing in repair LED Street / Security light fitting of 30 Watt, 5700K - 6500 K (including LED drive and internally prewired) complete with body robust, corrosion resistant, superior finish and without any cracks or through holes, made in a single piece by high pressure die cast aluminum alloy. The luminaries shall be monolithic construction totally enclosed dust and water proof with IP -65 / 66 protection as per IS - 10322-1982(Part -I) with latest amendments and input voltage range 140 - 300 V, AC, frequency 50 - 60 Hz ,P.F should be more than 0.9 with Total Harmonic Distortion THD(I) less than 15% ,cool white colour and lamp starting time should not be more than 10 second including 10 KV surge protection in built or external. Driver should be constant current constant voltage driver. Driver should have high voltage withstanding capacity upto 300 V, AC. Driver should also have double phase protection, no load , open circuit and short circuit protection .LED light fitting should be suitable for ambient temperature from -10 degree Centigrade to 50 degree Centigrade and humidity level 10% to 90 % RH. Covers should be polycarbonate/toughened glass to ensure minimum IP 65 degree protection. Cover should not degrade due to heating and ageing. The efficiency of LED luminaries system shall be more than 100 lumens per watt and must be certified by the LM-79 test report and including connection for street light from pole box with 1.5 Sqmm, 3 core PVC insulated stranded copper conductor FRLSH cable, 1100 Volts grade ISI marked including addition / alteration in bracket (if required) for fixing light fitting complete all as specified and directed by Engineer-in- charge. Havells cat Part LHETAVU7PA7J030/ Crompton cat part No TRP-415-30-57-SL-LM-NBK/ Wipro Cat part No- D923065

S&F as in repair street light bracket made out of 32mm dia GI pipe light grade 1.20m long , bent to shape at 120 degree angle from vertical fixed along pole with and dirlling holes including required number of clamp made out of Flat iron 25mm x 6mm with nuts, bolts ,washers etc. duly painted with two coats of aluminium paint including any addition / alteration (if required) for fixing street light complete all as specified and as directed by Engineer-in-charge.

S&F in replacement Sub main wiring complete with 2 single core 6 Sqmm (Nominal area) multi stranded copper conductor PVC insulated unsheathed cable FRLSH drawn in and including heavy duty PVC conduit ISI marked not less than 25mm dia concealed including single core multistranded copper conductor 6 Sqmm size cable as earth continuous wire drawn in same conduit complete all as specified and directed by Engineer-in- charge Note : Two runs of 6 Sqmm single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with fittings shall be measured as one length.

S&F HDPE DWC pipe inner dia 50mm and outer dia 63mm for laying in cable laid in trenches complete all as specified and as directed

S&F as in repair Galvanized iron tubing, 40mm bore light grade, ISI marked, including all fittings and laid in trenches / under road / drains, fixed to poles / walls with required numbers of clamps made out of 25x3mm flat iron, bolts, nuts and washers for protection of LT electric cable complete all as specified and as directed by Engineer-in-charge. Notes :- (i) Excavation & earthwork shall be measured & paid for separately under respective items of BOQ (ii) Cost of flat iron clamp if required is included in the unit rate of this item. Nothing extra shall be paid on this account. --------------------------------------------------------------------

BANSAL BROTHERS (BID ID -3465563)

S.K BUILDERS AND ENGINEERS (BID ID -3470596)

PACHAR BROTHERS (BID ID -3466785)

godara construction company (BID ID -3466513)

AK CONSTRUCTION (BID ID -3466756)

M/S Shree Ram Enterprises (BID ID -3471852)

PAREEK AND COMPANY (BID ID -3465635)

MAHIPAL CONSTRUCTION COMPANY (BID ID -3466245)

SRI SAI CONSTRUCTION COMPANY (BID ID -3471640)