ADDITIONAL AND ALTERATION TO BUILDING NO P-17 AND P-18 AT HALDIA UNDER GE (I) (CGN) KOLKATA

Amount

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed.

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slabs/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 25 mm average depth including saw-cutting of all edges making square shoulders of the cavities complete all as specified and as directed. (All loose unsound and cracked concrete shall be removed out side MD land) (Note: thickness will be measured excluding plaster)

Cleaning loose concrete if any all around reinforcement including from behind the reinforcing bars to give an average 10 mm thick (but not less than 10 mm clear air gap) and cleaning reinforcement of total rust using alkaline rust remover with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washed with water and allowing it to dry complete all as specified and as directed. (Note : - Length of reinforcement bars cleaned of rust all around will be measured for payment.) (Note: thickness will be measured excluding plaster)

Material and labour for providing and applying one coat of Epoxy bonding agent of approved brand. Coverage and specification of manufactures (Mixed density : 1.48 Kg/Ltr, adhesive bond strength to be >2.50MPa) complete all as specified and as directed.

Supply and application of Epoxy Zinc rich primer on the prepared steel surface by brush the primer shall have a minimium specific gravity 1.75 minimum weight film thickness/coat 40 microns and minimum adhesive bond strength with steel is 1.5N/mm2 complete all as specified and directed by Engr-in-charge

Material and labour for new reinforcement bar for structural connection in RCC beam, column, lintel and slab including power drilling holes of appropriate diameter in reinforcement or plain cement concrete to minimum dept of 150 mm and upto 200 mm including power dreilling, fixing the reinforcment in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy catridge etc complete all as specified and as directed by Engineer-in-Charge.

Supply, mixing and application two component structural grade polymer modified reinstatement morter, where local spalling has taken place or shuttering is not possible . The morter can be applying in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications. The mortar should have a minimium compressive strength 12N/mm2 in 1 day and 45N/mm2 in 28 days. Minimum flexural strength should be 8 N/mm2 in 28 days. A modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar to be used @ 6 ltr/bag of cement. The bonding agent should have minimium compressive strength 24N/mm2. Minimum tensile strength 3.5N/mm2, minimium flexural strength 6.5N/mm2 complete all as spd and directed by the Engr-in-charge upto 25 mm average thickness . NOTE:- Cement and sand morter in proportion of 1:2 graded (coarse sand ) with polymer admixed in proportions approved by Engr-in-charge)

Supply and fixed hot rolled medium and high tensile structural steel of grade E 250 quality A conforming to IS 2062: 2011 as in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) complete all as specified and as directed.

Material and labour for wax based white pigmented liquid curing compound, based on paraffin and also white pigmented to substantially increase light reflectance to effectively prevent premature water loss from the concrete both due to heat of hydration and sunlight, confirming to ASTM - C 309-89 Type 2 Class A, apply using low pressure sprayer uniformly on plaster surface, complete all as specified and as directed and as per manufacturer’s instruction. (NOTE:- Scaffolding required shall be measured and paid separately).

Material and labour for plastering 10 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 finished even and smooth without using extra cement including chicken wire mesh and all necessary scaffolding and lifting arrangement for external surface of any height complete all as specified and as directed.

Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:6 finished even and fair complete all as specified and as directed.

Demolition of cement concrete(unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour for Non skid ceramic coloured designer seamless tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm,in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and labour for double charge fully vitrified ceramic tiles 10 mm thick area of each tiles exceeding 0.42 sqm but not exc 1 sqm,in floors etc.set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

Material and labour for cement concrete 1:2:4, type B0 using 12.5 mm nominal size graded crushed stone aggregate, 25 mm thick in sub base for laying tiles, pavings, floorings etc. complete all as specified and as directed.

Material and labour for glazed ceramic coloured designer seamless tiles, 300x450x7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in coloured cement to match with the surface over and including 15mm thick screed in cement mortar 1:4 complete all as specified and directed. .

Supply and fixed in repairs brass chromium plated shower rose 125 mm size, fancy type, with CP brass chromium plated arm 225 mm with or without swivel joints, any size, including fixing to 15 mm bore steel pipe or union complete all as specified and as directed.

Supply and fixed in repair two in one 15mm dia fancy type CP bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipes or for brass ferrule complete all as specified and as directed.

Supply and fixed in repairs15mm dia fancy type angular stop valves cast copper alloy chromium plated fancy type screwed down high pressure screwed both ends for pipe or union fixed complete all as specified and as directed.

Supply and fixed in repair vitreous china wash down water closet pan (Pedestal pattern ) white Wall Hung WC With In Built Jet, PP Soft Close Slim Seat, Hinges, Accessories Set, Size 365x525x400 mm including with P or S trap with plastic closet seat cover white including 10 litres capacity PVC valveless, syphonic action type, flushing cistern, white colour, low level, white with inlet, ball valve, float and handle including brackets duly painted, 32mm dia PVC flush pipe and 600mm connector pipe,closed pattern with flat bottiom and cover and mild steel chromium plated complete all as specified.

Supply and fixed in repair vitreous china Table Top wash basin, white flat back of size 485x370x150mm, excluding tap incl bracket complete all as specified and as directed.

Supply and fixed in repair wall mixture 3-in -1 system with provision for both hand shower and overhead shwer complete with 115mm long bend pipe, connecting legs and wall flange(with hand & over head shwer) telephonic brass CP tap for mixing hot and cold water including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete

Supply and fixed in repair wash hand basin mixture central hole basin mixer without Popup Waste System with 450mm Long Braided Hos Brass CP tap for mixing hot and cold water including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete.

Supply and fixed health faucet with jet spray, 1.5 metre long, cast copper alloy, nickel chromium plated finish, 15 mm bore, 100 mm long with 1.5 metre long stainless steel shower hose and mounting device attached to wall complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15 mm bore of steel tubing and connections, including cleaning for refixing or removal to store or taken on schedule of credit complete all as specified.

Taking up or down 20 mm bore of steel tubing and connections, including cleaning for refixing or removal to store or taken on schedule of credit complete all as specified.

Supply and fixed three layer UV stablised with antymicrobial property fusion welded UPVC concealed pipes 20 mm outer dia ISI marked and fitting including plan upvc fitting and bress threaded upvc fittings and clumping fixed to wall, ceiling or floor , including cutting chases completed all as specified

Supply and fixed three layer UV stablised with antymicrobial property fusion welded upvc concealed pipes 25 mm outer dia ISI marked and fitting including plan upvc fitting and bress threaded upvc fittings and clumping fixed to wall, ceiling or floor including cutting chases ,completed all as specified

Material and labour for cement concrete 1:3:6 Type C1, using 20 mm nominal size graded crushed stone aggregate as in fixing of hold fastsdoor, window, frame or chowkhat including necessary formworks complete all as specified and directed by Engineer-in-charge.

Material and labour for 20 mm thick granite (Pure Black) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like over 20 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including rounding the edges of slab all around complete all as specified and as directed.

Material and labour for repair to Chajjas/Facias not exc 1.0 sqm area at any height of building including necessary formwork & scafolding, plaster on top, side and soffits of chajjas/facias wherever damaged, RCC 1:2:4 type B1 reinforced duly welded reinforcement if required any and necessary surface finished as per existing including all formwork and scaffolding complete all as specified.

Material and labour for repair to Chajjas/Facias exc 1.0 sqm area at any height of building including necessary formwork & scafolding, plaster on top, side and soffits of chajjas/facias wherever damaged, RCC 1:2:4 type B1 reinforced duly welded reinforcement if required any and necessary surface finished as per existing including all formwork and scaffolding complete all as specified.

Supply only liquid water proofing compound confirming to IS2645:2003 complete all as specified and as directed.

Material and labour for preparation of newly plastered surface of and applying two coats of oil bound distemper over one coat of alkali resistant primer over 3 mm thick in two coat wall putty (2 +1 mm) to match the existing surfaces complete all as specified and as directed

Material and labour for Complete removal of existing treatment of wall and painted surfaces and applying two coats of oil bound distemper over one coat of alkali resistant primer over 3 mm thick in two coat wall putty (2 +1 mm) to match the existing surfaces complete all as specified and as directed

Material and labour for preparing new plaster surfaces walls including chajjas, facias etc. and applying two coat of weather proof acrylic exterior paint (100% Acrylic) over a coat of primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Preparation of newly plastered surfaces on ceilings and applying two coats of white wash complete all as specified and as directed.

Material and labour for complete removal of existing finish on walls including chajjas, facias etc and applying one coat of exterior grade putty and two coat of weather proof acrylic exterior paint (100% Acrylic) over a coat of acrylic primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) in any position below or above ground floors, not exceeding 15 cm in depth complete all as specified and as directed.

Supply and fixed rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

Material and labour 75 mm thick plain cement concrete 1:3:6 type C1 using 20 mm nominal size graded stone aggregates finished surface even and fair as in plinth protection all as specified and as directed.

Material and labour for chequered cement concrete tiles, cast in rubber mould, glossy finish of approved colour, general purpose, double layer, size 30 cm X 30 cm X 25 mm thick, with mixture of white and grey cement in equal proportions and pigments, set, jointed and pointed in neat cement slurry in floor including laying over 20 mm thick bedding of cement mortar(1:4) all as specified and as directed.

Supply and fixed towel rail 450 mm long of PTMT fixed with and including chromium plated brass screw and wooden/plastics cleats, minimum weight 170 gms complete all as specified and as directed.

Supply and fixed grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40 gms) complete all as specified and as directed.

Supply and fixed sinks with drainage board made of stainless steel 1 mm thick sheet kitchen or laboratory with plugs, washers and 40 mm nominal size, copper alloy, nickel chromium plated finish waste fittings with including silicone sealant; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipes overall size 915 mm X 460 mm bowl size 410 mm X 330 mm X 160 mm complete all as specified and as directed.

Supply and fixed stainless steel curtain rod made out of stainless steel sheet of grade X02Cr19NilO (304 S2), surface finish No. 4 as per IS 6911: 1992, 25 mm dia including brackets and holders and ring, ball shaped knobs, at bothnend in golden colour etc. complete all as specified and as directed.

Supply and fixed Kitchen stainless steel plate rack of size 900 X 600 X 250 mm, made out of the 1 mm thick stainless steel including necessary fixing / fittings & making good the existing surfaces complete all as specified and directed.

Supply & fix soap dish CP brass fancy type complete all as specified and as directed.

Material and labour for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) of internal dia 100 mm, set in cement mortar complete all as specified and as directed.

Material and labour for concrete bed to drain pipes of internal diameter 160 mm, in cement concrete 1:3:6 type C2, using 40 mm nominal size graded crushed stone aggregate including packing under and haunching against the sides of pipes complete all as specified and as directed.

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

M & L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer in charge.

Material and labour for brick work with fly ash bricks of class designation 7.5 as per IS 12894: 2002, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with fly ash bricks of class designation 7.5 as per IS 12894: 2002, straight or curved on plan any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and as directed.

Taking up cast iron water mains (including all fittings), 80 mm nominal size, with spigot and socket ends and lead joints including burning out joints and recovering lead complete all as specified and as directed.

Supply and fixed PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed by Engineer- in- charge.

Supply and fixed UPVC bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge.

Material and labour for RCC 1:2:4 type B0, using 12.5 mm nominal size graded crushed stone aggregate as in chajjas complete all as specified and as directed.

Material and labour for formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for running welding in repair n. exc 2.5cm in length for plate of thickness not exceeding 6 mm complete all as specified and as directed.

Material and labour for precast reinforced cement concrete 1:1.5:3 type B1, using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) complete with joints to match complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separatly.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including any pattern roof coverings complete all as specified and as directed.

Supply and fixed Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed

Taking down existing treatment of any description and any layer from roof including scraping and roughening old by picking, sweeping clean and washing down complete all as specified and as directed.

Material and labour for 40 mm thick cement concrete, 1:2:4, type B-1 using 20 mm nominal crushed stone aggregate at roof including water proofing compound as per manufacturer'r instruction, finished surface even and fair complete all as specified and as directed.

Material and labour for preparing RCC roof surfaces with wire brush drying and cleaning to remove all foreign materials and washing with water to remove loose particle and providing 10 mm thick cement plaster in CM (1:4) using water proofing compound @ 3 % by weight of cement for filling depression if any to receive water proofing treatment and providing APP modified bituminous membrane water proofing membrane with polyester reinforcement and plain finish of 3 mm thick (not less than 3.8 kg/sqm ± 5% per sqm) consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/Sqm by the same membrane manufacture of density at 25 C, 0.87-0.89 kg/litre and viscosity 70-160 cps over the primer coat the layer of membrane shall be laid using Butane torch application method overlap while torching shall be 75 mm on length and 100 mm width side, all angles & bituminous should sealed with extra care to ensure full bondage all joints including for applying bituminous aluminium paint @ 0.125 Kg / sqm on finished APP surface complete all as specified and as directed by Engineer-In-charge (Note : WPC shall be measured and paid separately)

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed

Supply and fix Aluminium deco grill Cat No DG-104, 10 mm thick ,cut to required size/shape and fixed in position with aluminium beading complete all as specified and directed by Engineer-in-Charge.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area exceeding 2.00 sqm each

Supply and fixed 5.5mm thick sheet glass ordinary quality alongwith EPDM rubber all around the glass edges exc 0.50 sqm in each pane and fixed into aluminium frame work complete all as specified and as directed.

Supply and fixed 5.5mm thick frosted sheet glass ordinary quality alongwith EPDM rubber all around the glass edges exc 0.50 sqm in each pane and fixed into aluminium frame work complete all as specified and as directed.

Supply and fixed stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Demolition of wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness including cover fillets of any description including all snap grids and hanging arrangements complete all as specified.

Material and labour 4mm thick non asbestos cement plain building board fixed to timber frame work with screws in ceiling complete all as specified and as directed by Engineer-in-charge.

Material and labour anodised aluminium snap grid frame work for false ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the ntermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed by Engineer-in-charge. .

Material and labour for Hangers 6mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by mean of ceiling cleats made out of G.I. flat 40x3 mm size long, grid 605mm x 605mm complete all as specified and as directed.

S& fix in repair block board, exterior grade, including sanmica pasting both side fixed with screws to timber frame work in cup board for short area including 40mm dia knob and magnet catch complete all as specified and as directed by Engineer-in-charge.

Taking down carefully the existing aluminium/copper point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets, ceiling rose, fan regulators, lamp holders, call bell, bell pushes any type etc by unscrewing and taken away from site complete and make good the disturbed surface as existing. Note :(i) cost of unserviceable materials will be charged from the contractor against schedule of credit. (ii) Serviceable light fitting shall be kept in safe custody for reuse at site. (iii) Re-fixing shall be measured and paid seperately.

Taking down unserviceable submain wiring any size,complete all as specified and directed.

Material and labour for point wiring with 1.5 sqmm PVC insulated FRLS sheathed 1100 Volts grade copper multi stranded conductor drawn through and including rigid PVC conduit 20 mm dia concealed in walls ,roofs, etc including 1.5 sqmm PVC insulated copper conductor as earth continuity conductor and other accesories such as metal box, sheet cover, screws,nuts etc connecting it to the common earth dolly all as specified for one light/ceiling fan/Exhaust fan / wall fan each controller by one way switch

All as per item no 87 but One light point controlled by two 2 - w a y switches , with cables 1.5 sq. mm size complte all as specified and as directed.

All as per item no 87 but one 3 pin 5 Amps socket outlet on same board controlled by one switch complte all as specified and as directed.

All as per item no 87 but one 3 pin 5 Amps socket outlet independent controlled by one switch complte all as specified and as directed.

All as per item no 87 here in before but with 2.5 sqmm cable copper for 15/ 16 Amps socket outlet on independent board ,including 2.5 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly.

All as per item no 87 here in before but with 4.0 sqmm cable copper for 15/16 Amps socket outlet on independent board,including 4.0 sqmm copper conductor PVC insulated sheathed continuous earth wire and connecting to common earth dolly ( for AC) complte all as specified and as directed.

Material and labour Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/ recessed as required in PVC Conduit conceiled type 2x6.0 sqmm + 1x6.0 sq. mm for earth wire all as specified and directed

Supply and fix LED batten 20 Watt extruded aluminium housing,high power diffuser, slim and integrated design, lumen not less than 2100 lumen polycarbonate, energy efficient fixed to wall/ ceilling and connecting upto ceilling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing complete all as specified and as directed.

Supply and fix LED batten 10 Watt extruded aluminium housing,high power diffuser, slim and integrated design, lumen not less than 1000 lumen polycarbonate, energy efficient fixed to wall/ ceilling and connecting upto ceilling rose with three core twisted flexible 1.5 sqmm PVC copper conductor cable with earthing complete all as specified and as directed.

Supply and fixed high energy efficient LED bulb 9 Watt, incl taking down old one from existing decorative light fittings complete all as specified and directed.

Supply and fixed decorative lamp type led light fitting 9 Watt, wall mounted,brushed nickle finish fixture with opal glass diffuser suitable for 9 W LED light B22/E27 or suitable base, incl taking down old one complete all as specified and directed.

Material and labour Switch Modular type single pole, one way 6 Amp complte all as specified and as directed.

Material and labour Switch Modular type single pole, two way 6 Amp complte all as specified and as directed.

Material and labour Modular Bell push 6A 1 module complte all as specified and as directed.

Material and labour Modular Socket, 6A - 2/3 pin combined 2 module, complte all as specified and as directed.

Material and labour Modular Switch socket combination outlet 2/3 pin 6 amp' flush type combined 3 module complte all as specified and as directed.

Material and labour modular Switch socket combination multipurpose 2/3 pin, 16 amp and one pin, 6 amp controlled by one switch 3 module complte all as specified and as directed.

Supply and fixed Modular Fan step regulator, 120W - 2 module complte all as specified and as directed.

Supply and fixed Modular White cover plate with frame 1/2 M incl taking down old one.

Supply and fixed Modular White cover plate with frame 3 M incl taking down old one complte all as specified and as directed.

Supply and fixed Modular White cover plate with frame 4 M incl taking down old one complte all as specified and as directed.

Supply and fixed Modular White cover plate with frame 6 M incl taking down old one complte all as specified and as directed.

Supply and fixed Modular White cover plate with frame 8 M incl taking down old one complte all as specified and as directed.

Supply and fixed Metal flush box 1/2 module incl taking down old one complte all as specified and as directed.

Supply and fixed Metal flush box 3 module incl taking down old one complte all as specified and as directed.

Supply and fixed Metal flush box 4 module incl taking down old one complte all as specified and as directed.

Supply and fixed Metal flush box 6 module incl taking down old one complte all as specified and as directed.

Supply and fixed Metal flush box 8 module incl taking down old one complte all as specified and as directed.

Supply and fixed ceiling rose 3 terminal PVC/polycarbonate isolated body type complte all as specified and as directed.

Supply and fixed Buzzer, Ding Dong AC. 230 volts, single pole complte all as specified and as directed.

Supply and fixing SP 6-32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complte all as specified and as directed.

Supply and fixing SPN 32 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complte all as specified and as directed.

Supply and fixing SPN 63 amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply and fixing MCCB 4P 63 Amp rating 415V, 16 KA in DB complete with connection testing and commissioning complte all as specified and as directed.

Supply and fix 2 way SPN Double door DB with 200 amps rated bus bar complte all as specified and as directed.

Supply and fix 8 way SPN Double door DB with 200 amps rated bus bar complte all as specified and as directed.

Supply and fix 4 way TPN Double door DB with 200 amps rated bus bar complte all as specified and as directed.

Material and labour Flush type AC starter 6 M with DP MCB and plug top with indictor complte all as specified and as directed.

Supply and fix blank plate of 1 module for switch and mcbs complete all as specified and directed.

Taking down ceiling fan/ exhaust fan, ceiling cable end, dismantling blades any type and any sweep removal to store or taken on schedule of credit complete all as specified.

Servicing of ceiling fan/ exhaust fan incl open all parts, lubrication, cleaning and other necessary job to make smooth run of the item Complete all as specified and directed.

Material and labour for Spray Painting of ceiling/ wall fans and Exhaust fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc.

Re-Hanging ceiling fan, and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Re-Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified and directed.

Fixing only serviceable LED light fitting of any type and any watt retrievied from item No 85 complete all as specified and directed.

Supply & fix single pointed air termination aluminium rod 12mm dia, 300 mm long including 40 mm dia GI pipe of length 1.2 Mtr with clamping, nuts, bolts, base plate , PCC foundation complete all as specified and directed by Engr-In-Charge.

Supply & fix aluminium strip 25 mm x 3 mm complete with saddles and fixing screws for conductor and ground conductor above ground complete all as specified and directed.

Supply and fixed Earthing complete with Galvanised steel earth plate electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the plate by means of GI Bolts & Nuts complete all as per Electrical plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and directed.

Material and labour Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

Supply and fixed Tubes, 'light grad', galvanised 80mm bore with all fitting; laid in trenches complete all as specified and directed.

Taking down, servicing, testing and re-fixing in the same or other location of geyser of any capacity complete all as specified and as directed.

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with light fitting bracket and suitable size GI/aluminium pipe for light fitting at wall complete all as specified and directed.

BHARAT TRADING CORPORATION (BID ID -3167073)

JOTSHNA ELECTRICALS (BID ID -3161068)