PROVN TO ADDN ALTN TO BLOCK NO P26 OLD UMRAO COLONY AND CONSTRUCTION OF 01 REST ROOM WITH TOILET AND BATHROOM IN SEWAGE TREATMENT PLANT OF MD ACCN AND ADDN ALTN TO MAIN ENTRY GATE ALONGWITH VISITOR SHED AT MIL STN BIKANER

Amount

Dismantling of Roof tiles of any description or thickness in floor, roof, apron etc laid, bedded and pointed in any mortar complete all as specified and as directed by Engineer-in-Charge.

Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge.

M&L for 10mm thick rendering (screeding) over roof slab in CM 1:6, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished fair & even, complete all as specified and as directed.Note : Supply only integral liquid water proofing compound shall be measured and paid for separately complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing compound ISI Mark complete all as specified and as directed by Engineer-in-Charge.Make: Dr. Fixit or Equivalent.

M&L for cleaning of all loose dirt and dust from roof and priming the surface with one coat of cold applied bituminous primer @ 0.40 litre/sqm and provide a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3mm thick, reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) laid on primed surface complete all as described in Para 11.44.5 of SSR Part-I, complete all as specified and as directed by Engineer-in-Charge. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps.

M&L for Lime concrete terracing in roof with minimum thickness at edge 40 mm and increasing uniformly towards ridges to obtain a chain slope of (1:40) as described in Para 11.27.2 of MES Schedule Part-I complete all as specified and as directed by Engineer-in-Charge.

M & L for 40 mm thick brunt clay brick tiles bedded on cement mortar and joints grouted flush in cement and sand mortar (1:3) mixed with integral water proofing compound IS 2645 : 2003 @ 3% by wt of cement complete all as specified and as directed by Engineer-in-Charge.

ditto complete all as per Item No 7 above but except tiles complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling any type including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the primises complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-Charge.

M & L for coloured Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed by Engineer-in-Charge.

Ditto all as above item 11 but as in skirting/dado over and incl 10 mm thick rendering in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (squar/ rectangular) area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M & L for coloured Glazed ceramic tiles 450mm x 350mm x 7mm OR 300mm x 450mm x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10 mm thick cement plaster in 1:4 complete all as specified and as directed by Engineer-in-Charge.

M & L for 25 mm thick Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in floors to receive finished even and smooth using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for 20-25 mm thick Machine cut Kota stone slab flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and Wax polishing including laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

M & L for 20-25 mm thick Machine cut Kota stone in riser to steps, skirting, dado and pillar etc on vertical surfaces laid over 10 mm thick cement plaster in 1:4 complete all as specified and as directed by Engineer-in-Charge.

Demolition of reinforcement concrete of any description and in any position not otherwise specifically provided for concrete complete all as specified and as directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surface complete all as specified and as directed by Engineer-in-Charge.

Formwork to faces of walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters, buttresses, etc.; vertical or to better complete all as specified and as directed by Engineer-in-Charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roof slabs and shelves, sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but not exc. 10cm widecomplete all as specified and as directed by Engineer-in-Charge.

M & L for design mix M-25, using 20mm graded stone aggregate in slabs supported on walls, beams & columns and shelves and the like complete all as specified and as directed by Engineer-in-Charge. (reinforcement to be measured separately)

M & L RCC design mix M-25, for walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed by Engineer-in-Charge.

M&L for 16 to 18mm thick Granite (of any type) machine cut slab of approved shade (table rubbed and mirror polished) with true & uniform joints as in steps, jambs, pillars, window cills, cooking platforms & like and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed (bedding layer) in CM 1:4 with cement slurry @ 3 Kg/Sqm complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1 Sqm but not exc.2 Sqm each and refixing in the same opening after necessary easing, repairs, adjustment etc. complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames not exc. 1.50 Sqm each but with shutter (with out taking of shutter from the frame ) and making good the surface of walls as per existing with cement mortar complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames exc. 1.50 Sqm each but n.exc 4 Sqm with shutter (with out taking of shutter from the frame ) and making good the surface of walls as per existing with cement mortar complete all as specified and as directed by Engineer-in-Charge.

Taking down shutter of any description exc. 1sqm but not exc.2 sqm each complete all as specified and as directed by Engineer-in-Charge.

S & F for pressed steel frames of size 125 x 60 mm with one or more rebates including necessary fixing lugs hinges, locks trike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

S & F for pressed steel frames of size 105 x 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

S & F for pressed steel frames of size 75 x 60 mm with one or more rebates including necessary fixing lugs hinges, locks strike plate etc (thickness of sheet shall be 1.25mm) and making good the plaster of wall in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

Cutting holes in brick walls in cement mortar exc half brick but not exc one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed by Engineer-in-Charge.

S & F for bands, straps, supports or stays for rain water, ventilating pipes, including bolts, if required, hooks and pintal hinges, large hasp and stapals, chains hand made sliding bolts, clamps, hold fast,wall ties, hooks for hanging fans, plain angle cleats for securing purlins to woods trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articals conforming to Fe 290 Gde-E-165 complete all as specified and as directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C-1 (using 20mm Graded Stone Aggregate) as in fixing Holdfast, Plinth courses, bed plates, string courses, coping, filling of chowkhats etc., complete all as specified and as directed by Engr-in-Charge.

S & F 2nd class HW 35mm thick factory made panelled shutters with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS-1003 (Pt-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

S & F 2nd class HW 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc (w/o sash bars) complete all as specified and as directed by Engineer-in-Charge.

S & F of 30 mm thick glass fibre reinforced plastic (FRP) door frame confirming to IS:14856-2000 of required colour and specification, Make, made with fire retardant grade unsaturated polyester resin moulded to 3 mm thick FRP laminate for forming hollow rails and stiles with suitable second class hardwood timber blocks inside at required places for fixing of fitting cast monolithically with 5 mm thick FRP laminate including fixing to frames, complete all as specified and as directed by Engineer-in-Charge.manufacturers specification and drawings.

S & F of 30 mm thick glass fibre reinforced plastic (FRP) paneled coor shutter confirming to IS : 14356-2000 of required colour and specification, Make, of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness, the laminate door frame mouded with fire retardant grade unsaturated polyester resin and chopped strand Mat (CSM). Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all the three legs. The frame shall be covered with fiberglass from all sides. MS stay flat Iron 25 x 3 mm shall be provided at the bottom steady the frame, complete as per direction of Engr-in-Charge, manufacturer’s specification and drawings.

S&F rubber gasket of 2.5mm thickness (minimum) and width 60mm, fixed with steel screws or black nails with plate washers to wooden doors to cover the gap between door and floor complete all as specified and as directed by Engineer-in-Charge.

M & L stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.

M & L stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S & F for 100 mm long powder coated Aluminium Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and as directed by Engineer-in-Charge.

S & F for 150 mm long, aluminium, powder coated, barrel tower bolts of extruded section complete all as specified and as directed by Engineer-in-Charge.

S & F for 150 mm size aluminium powder coated handles, cast type, anodised complete all as specified and as directed by Engineer-in-Charge.

S & F for 100mm size butt hinges, medium weight cold rolled mild steel complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs stainless steel Peg Set of Six of standard size (not less than 300mm long) fixed to wall with two rawl plugs and chromium plated brass screws complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part No. BEA-30 of Prayag or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F iron body capsule door closure of best quality for glazed & skeleton door shutters, standard size, conforming to the sample kept in GE’s office, complete all as specified and as directed by Engineer-in-Charge.

S & F for 300mm long aluminum alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed by Engineer-in-Charge.

M&L for complete removal of existing treatment on wooden surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer including finishing with wooden putty after preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing new surface of wood of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

M & L preparation of old steel surfaces of any description, over 10 cm in width or girth, and applying one coat of synthetic enamel paint incl preparation complete all as specified and as directed by Engineer-in-Charge.

S & F for 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S & F for 4mm thick pin headed sheet glass, ordinary quality and glazing with oil putty in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work or stone boulder masonary of any description in and any position built in cement mortar or cement lime mortar complete all as specified and as directed by Engineer-in-Charge.

M & L Brick work with fly ash brick, straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

M & L Brick work with fly ash bricks (Half brick), straight or curved on plan exc. 6 m mean radius built in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

S & F GI tubing 15mm dia medium grade with all fittings and fixed to wall, floor and ceiling complete all as specified and as directed by Engineer-in-Charge.

Fixing only of old steel GI tubing, 15mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

S & F for GI tubing 20mm dia medium grade with all fittings and fixed to wall, floor and ceiling complete all as specified and as directed by Engineer-in-Charge.

Fixing only of old steel GI tubing, 20mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed by Engineer-in-Charge.

S & F for GI tubing 25 mm dia medium grade with all fittings and fixed to wall, floor and ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Fixing only of old steel GI tubing, 25 mm bore and connections in new or old position (walls, ceiling, floors etc) complete all as specified and as directed by Engineer-in-Charge.

M&L for 18mm thick Medium Density Fibre board, exterior grade, ISI marked, veneered with decorative face veneers one face, fixed to timber framework with screws, as in cupboard shutters, shelves, Kitchen cabinets, drawers and similar works, complete all as specified and as directed by Engineer-in-Charge.

S & F 30 mm wide continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and as directed by Engineer-in-Charge.

S&F butt hinges of size 75mm, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-12 complete all as specified and as directed by Engineer-in-Charge.

S&F 100mm size extruded brass handle, fabricated type polished complete all as specified and as directed by Engineer-in-Charge.

S&F mild steel magnet catcher of best quality with mild steel striking plate fixed with screws, conforming to the sample kept in GE’s office, complete all as specified and as directed by Engineer-in-Charge.

S & F 100 mm hasp and staple brass incl bolt to hinge plate and fixed with screws safety type complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 15 mm bore bib tap, brass, chromium plated, long body, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, including CP brass wall flange, complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4906A1’ of ‘Parryware’ / Cat Part No. ‘F2002152’ of ‘Cera’ / Cat Part No. ‘CQT-23047’ of ‘Jaquar’ / Cat Part No. ‘9208’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs 15mm bore Angle stop valve, brass, chromium plated, fancy type, screwed down, high pressure with capstan head, screwed both ends for iron pipe or for union, including CP brass wall flange, complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4907A1’ of ‘Parryware’ / Cat Part No. ‘F2002201’ of ‘Cera’ / Cat Part No. 'CQT-23059’ of ‘Jaquar’ / Cat Part No. ‘9210’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs 15mm bore two way Angle stop valve, brass, chromium plated, fancy type, screwed down, high pressure with capstan head, screwed both ends for iron pipe or for union, including CP brass wall flange,complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4943A1’ of ‘Parryware’ / Cat Part No. ‘F2002211’ of ‘Cera’ / Cat Part No. ‘9211’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs wall mixer, telephonic type, brass, chromium plated, fancy type, with capstan head handles with lettered 'hot' and 'cold', screwed down high pressure, including CP brass wall flanges and necessary extension nipples screwed for 15mm bore pipe connection, complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4916A1’ of ‘Parryware’ / Cat Part No. ‘F2002401’ of ‘Cera’ / Cat Part No. ‘CQT-23281UPR’ of ‘Jaquar’ / Cat Part No. ‘9275’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Centre hole mixer for mixing hot & cold water for wash hand basin, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe suitable for 15mm bore, complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4914A1’ of ‘Parryware’ / Cat Part No. ‘F2002461’ of ‘Cera’ / Cat Part No. ‘CQT-23167B’ of ‘Jaquar’ / Cat Part No. ‘9250’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Wall mixer for Kitchen sink, cast copper alloy, with dual capstan heads, chromium plated, screwed down high pressure, with lettered 'Hot' & 'Cold' with shaped CP brass nipples screwed for 15mm bore connections complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘G4935A1’ of ‘Parryware’ / Cat Part No. ‘F2002511’ of ‘Cera’ / Cat Part No. ‘CQT-23309’ of ‘Jaquar’ / Cat Part No. ‘9255’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Shower rose, round type, brass, chromium plated, Fancy type, 100 mm dia (minimum) with or without swivel joint, with & including CP brass arm and wall flange, fixing to steel pipe of 15mm bore or union complete all as specified and as directed by Engineer-in-Charge. Make : Cat Part No. ‘T9809A1’ of ‘Parryware’ / Cat Part No. ‘F7010212AB’ of ‘Cera’ / Cat Part No. ‘BOS-87’ of ‘Prayag’ or equivalent in makes mentioned in Appendix ‘B’ here-in-after.

S&F in repairs Soap dish, brass, chromium plated, heavy duty, fixed to wall with plugs with brass cadmium plated screws, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Towel ring round brass chromium plated with round flange fixed on wall with PVC rawl plug & cadmium plated brass screws complete all as specified and as directed by Engineer-in-Charge. Make :- Cat Part No 'ACN-1121BN' of make 'Jaquar' or equivalent in makes mentioned in Appendix 'B' here-in-after.

S & F as in repair, gun-metal, of 20 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

S & F as in repair, gun-metal, of 25 mm globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge.

Disconnecting & taking down the existing unserviceable water tank and Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top), ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I and as directed engineer-in-Charge.

S & F 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/40mm- 690 gms/50mm-1240 gms) complete all as specified and as directed by Engineer-in-Charge.

S&F sink with drainage board made of stainless steel 1mm thick for Kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brackets, bedding in cement mortar on to brick wall, connecting union to pipe, overall minimum size 1143mm x 510 mm with bowl size 510mm x 405mm x 203 mm including 40mm dia waste pipe of polythelene of low or high density, 40mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete all as specified and as directed by Engineer-in-Charge.including taking down old unserviceable sink with fittings.

S & F for waste pipe 40 mm for SINK with coupling complete all as specified and as directed by Engineer-in-Charge.

S & F as in repair, PVC flexible connections 450mm long 15mm dia with brass flange nuts & washers complete. Make: Prayag/Polytuf or equivalent as approved by Engr-in-Charge.

S & F as in repair, 75 mm dia CI floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed by Engineer-in-Charge.

S & F stainless steel grating suitable for 100 mm dia bore fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

S & F stainless steel grating suitable for 100 mm dia bore with hole fixed with white cement with outer square frame, complete all as specified as directed by Engineer-in-charge .

Demolition in concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed by Engineer-in-Charge.

M & L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in lintel upto 1.50m clear span, cills, steps, seismic and other similar bands, plinth courses , strings courses, lacing courses, parapets and railings upto 60 CM in height, copings, kneelers, apex stone, bed plates, kerb stones provided for including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engineer-in-Charge.

M & L for 75mm thick PCC 1:3:6 C2 using 40 mm graded stone aggregate as in plinth protection laid in panels and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed brick aggregate as in Sunken portion, surroundings of WC seats and similar works, complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick masonry or concrete surfaces of walls in Sunken portion, mixed with integral liquid water proofing compound as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note : Supply only integral liquid water proofing compound shall be measured and paid for separately.

M&L for removal of loose concrete and cleaning the surfaces and filling the cracks with Polymer modified mortar using Dr Fixit Pidicrete URP or other equivalent product as approved by GE and thereafter applying two coats of Dr Fixit Bathseal WPC or other equivalent product as approved by GE in Sunken areas complete all as per manufacturer’s instructions, complete all as specified and as directed by Engineer-in-Charge. Note : Where contractor desire to use equivalent product of Dr Fixit Pidicrete URP and Dr Fixit Bathseal WPC, he shall submit the technical literature of equivalent products to establish the equivalency of products to the entire satisfaction of GE and both products shall be of same manufacturer as approved by the GE.

Dismantling of cast iron drain pipe of 100mm bore, jointed in CM and taking out of trenches or floors, if required, complete all as specified and as directed by Engineer-in-Charge. Note :- Excavation & earthwork shall be measured and paid separately.

Supply and fixing 100 mm bore cast iron, soil, waste & vent pipes in any length with or without ears, spun pipes, ISI marked, fixed with cement joints, laid in trenches or floors, complete complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100 mm bore cast iron, soil, waste & vent pipes in any length with or without ears, spun pipes, ISI marked, fixed with cement joints, fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

Ditto as per item no- 100 but except pipes complete all as specified and as directed by Engineer-in-Charge.

Dismantling of cast iron drain pipe of 75mm bore, jointed in CM and taking out of trenches or floors, if required, complete all as specified and as directed by Engineer-in-Charge. Note :- Excavation & earthwork shall be measured and paid separately.

Supply and fixing 75 mm bore cast iron, soil, waste & vent pipes in any length with or without ears, spun pipes, ISI marked, fixed with cement joints, laid in trenches or floors, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 75 mm bore cast iron, soil, waste & vent pipes in any length with or without ears, spun pipes, ISI marked, fixed with cement joints, fixed to walls, complete all as specified and as directed by Engineer-in-Charge.

Ditto item no 104 but except pipes complete all as specified and as directed by Engineer-in-Charge.

Dismantling and disconnecting of existing CI soil vent pipe 50 mm bore fixed to wall,laid in trenches incl all fittings & accessories.complete all as specified and as directed by Engineer-in-Charge.

S & F 50 mm dia Cast Iron soil waste & vent pipes in any length with or without ears, with cement joints but fixed to walls with & including fixing clamps complete all as specified and as directed by Engineer-in-Charge.

Ditto item no 107 but except pipes complete all as specified and as directed by Engineer-in-Charge.

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 75 mm pipe complete all as specified and as directed by Engineer-in-Charge.

Extra over cast iron pipe and fittings if lead joint is provided in lieu of cement joint for 100 mm pipe complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 100 mm dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 75 dia branch piece single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs 75 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 100 mm bore CI bends (any radius), diminishing pieces or tapers (larger bore measured) without oval access door complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs 100 mm bore CI tee (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs, 100 mm CI bends (any radius) with duck's foot or heel rest complete all as specified and as directed by Engineer-in-Charge.

S & F as in repair, 100 mm cast iron sanitary connection socket in fit WC out-let complete all as specified and as directed by Engineer-in-Charge.

S & F for cast iron vent cowls 100 mm dia complete all as specified and as directed by Engineer-in-Charge.

S & F for cast iron vent cowls 50 mm dia complete all as specified and as directed by Engineer-in-Charge.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof for 50 mm bore complete all as specified and as directed by Engineer-in-Charge.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 75 mm bore complete all as specified and as directed by Engineer-in-Charge.

S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays. Including bolts and nuts and securing ends of stays to wall or roof 100 mm bore complete all as specified and as directed by Engineer-in-Charge.

Taking down PVC pipes and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc.,including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and as directed by Engineer-in-Charge.

S & F for PVC (SWR) 100 mm dia single socket in any length with rubber ring joints fixed to wall incl SS clamp complete all as specified and as directed by Engineer-in-Charge.

S & F for PVC (SWR) 100 mm dia bend of any radius fixed to wall complete all as specified and as directed by Engineer-in-Charge.

S & F for PVC (SWR) 75 mm dia single socket in any length with rubber ring joints fixed to wall incl SS clamp complete all as specified and as directed by Engineer-in-Charge.

S & F for PVC (SWR) 75 mm dia bend of any radius fixed to wall complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs stainless steel drapery rod of 25mm inner dia & 1.6mm wall thickness (in lengths as directed) with & including stainless steel sockets & decorative finial at both ends and pair of stainless steel brackets & stops fixed at both ends with PVC rawl plug & steel screws on walls/beam complete all as specified and as directed by Engineer-in-Charge. Notes : (i) The weight of each bracket shall not be less than 100 gm. (ii) Length of steel screw shall not be less than 65mm.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Corner glass shelving 3-tier of size 300mm, 200mm & 150mm, with CP brass brackets and guard & railing, conforming to sample kept in GE's office, complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, white, size 580x440mm with integral foot rests, ‘P’ or ‘S’ trap, including connection to trap and flushing pipe, antisyphonage pipe etc, making good to floor in CM 1:3, complete all as specified and as directed by Engineer-in-Charge.

S & F PVC valve less, syphonic action type, fluhsing cistern, 10 ltrs capacity, low level, white, with inlet, ball valve, float and handle including 32mm bore PVC flushing pipe, brackets and fixed in repairs including taking down existing flushing cistern of any description complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster/terrazo finish on brick or stone walll etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed by Engineer-in-Charge.

M & L for 10mm thick Rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces,incl water proofing liquid finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for 5 mm thick Rendering in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for rendering 10mm thick in cm 1:4 as setting coat and 5 mm thick in cm (1:4) as finishing coat as in chajja with WPC complete all as specified and as directed by Engineer-in-Charge. Note: - WPC should be measured and paid separately.

M&L for preparation of newly plastered surfaces of wall & chajjas and applying two coats of Acrylic emulsion paint (Exterior grade) of approved shade/tint over a coat of suitable priming paint complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing new plastered or unplastered surfaces of ceiling and applying two coats of OBD over a coat of primer complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing new plastered or surfaces of walls and applying two coats of distemper oil emulsion, white or tinted over & incl a coat of primer over & incl 3mm thick Birla white putty complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of old surfaces by complete removal of existing treatment of walls incl paillars etc. by mechanical equipment like electric wall sander and applying two coats of oil bound distemper using rollers over a coat of primer incl two coats/layer of wall care putty complete all as specified and as directed by Engr-in-Charge.

M&L for complete removal of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applying two coats of Acrylic emulsion paint (Exterior grade) of approved shade/tint over a coat of suitable priming paint on walls complete all as specified and as directed by Engineer-in-Charge.

M & L for complete removal of existing treatment of old painted surfaces old decorated plastered or unplastered surfaces of ceiling and applying two coat of OBD over a coat of primer and wall care putty complete all as specified and as directed by Engineer-in-Charge.

M & L for framed work such as grills, gratings etc. with ends of bars shouldered and or rebated or forged into spikes, framed guard bars etc confirming to Fe-290-Gde-E-165 incl dismantling the same complete all as specified and as directed by Engineer-in-Charge.

Removing building materals etc., (other than spoil payable under items 99 to 102 in Section 3-Earthwork) to a distance 5 km or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed by Engineer-in-Charge.

S&F aluminium frame powder coated of any colour as approved (Thickness of powder coating not less than 50 micron) for doors, windows, ventilators, partitions, with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed. Note : Frame to walls etc shall be fixed with PVC rawl plugs and steel screws of length not less than 75mm at places as directed. Quoted rate shall deemed to include the same complete all as specified and as directed by Engineer-in-Charge.

S&F aluminium window and ventilator shutters, powder coated of any colour as approved (Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws, complete all as specified and as directed by Engineer-in-Charge. Note : Glass and rubber neoprene packing / rubber gasket shall be measured and paid for separately as “Supply only” under respective item of this Schedule.

Supply only 5.0 mm thick Sheet glass, ordinary quality in square n exc 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

Supply only rubber neoprene packing / rubber gasket of required size & profile suitable for glazing etc in aluminium frame work in doors, windows, etc complete all as specified and as directed by Engineer-in-Charge.

S & F 20 mm wide hard wood decorative moulding/beading, machine made with some pattern, fancy type, fixed with nails/adhesive as required complete all as specified as directed by Engineer-in-charge.

M & L for 2nd class soft wood (kail) scantling, clean sawn timber framed and fixed, complete all as specified and directed by Engr-in-Charge.

M&L for anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed by Engineer-in-Charge.

M&L for anti termite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-Charge.

Cutting chases, pining in, making good to facings where required and pointing in cement mortar 1:3, for concealed water tubing etc and maing good, cutting exc 10cm and not exc 20 cm girth complete all as specified and as directed by Engineer-in-Charge.

M & L for 75 mm thick plain cement concrete 1:2:4, type B-2 (using 40mm graded crushed stone aggregate) even and fair w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

S & F rubber moulded machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment (Yellow & reddish) complete all as specified and as directed by Engineer-in-Charge.

S&F Steel Fibre Reinforced Concrete (SFRC) manhole cover and frame, Light duty (LD-2.5 grade designation) of 560 mm internal dia, conforming to IS-12592, ISI marked, fixed in position with cement mortar (1:4)/PCC type B-1 complete all as specified and as directed by Engineer-in-Charge.

Forming jambs, etc. in CM 1:4, to openings (to foregoing item), with stone supplied by MES including cutting, toothings and properly bonding into old work, including facing and pointing (if necessary) to match existing work, complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches for foundation etc not exc 1.5m wide and not exc 1.5 m in depth in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass complete all as specified and as directed by Engineer-in-Charge.

Returning filling in including spreading levelling , atering and well ramming in layers nexc 25cm thick complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated material to a distance nexc 50 m and depositing at a level nexc 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and as directed by Engineer-in-Charge.

M & L for cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass complete all as specified and as directed by Engineer-in-Charge.

M & L for broken stone Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.

M & L for 75mm thick Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in floors and paving, laid in panels and finished even & fair complete all as specified and as directed by Engineer-in-Charge.

M & L for 25mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) and finished even & smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I S.1161-1979 grade St.-240 complete all as specified and as directed by Engineer-in-Charge.

M & L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde- E- 250) quality- A complete all as specified and as directed by Engineer-in-Charge.

M & L Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to GDE Fe410-0 or Fe 310-O complete all as specified and as directed by Engineer-in-Charge.

S & F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with L-type or J-type or cranked hook bolts complete all as specified and as directed by Engineer-in-Charge.

M & L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

M & L for 15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished rough for receiving tiles as in dado complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing new plastered surfaces and applying two coats of cement base paint over a coat of suitable primer on surfaces of walls complete all as specified and as directed by Engineer-in-Charge.

S & F powder coated anodized aluminium snap grid frame work of size 605 x 605 mm for false ceiling including necessary notching. The snap grid shall consist of anodized aluminium main & cross tee of size 36.5 x 25 x 1.4 mm weighing 0.24 Kg/RM and 23.5 x 26.4 x 1.40 mm weighing 0.191 Kg/RM respectively. The main and cross tee shall be jointed at junction crossing with anodized aluminium angle bracket of size 15mm x 15mm x 1.5 mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washer. The snap grid (main/cross tee section) shall be supported at ends all along the wall with anodized aluminium angle of size 35 x 25 x 2 mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and providing 6 mm thick AC boards of Make Everest or euivalent. (designer/ pattern shall be as approved by the Engineer-in -charge) boards in grid fixed as false ceiling grid made of aluminium as per specification incl 6 mm dia MS round bar as in suspension to support snap grid.all as specified and as directed.

M & L for powder coated anodised aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing complete all as specified and as directed by Engineer-in-Charge.

M & L for powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door,hinges, anodised alumnium snap beading, screws etc. complete all as specified and as directed by Engineer-in-Charge.

M & L for powder coated anodised aluminium window and ventilator shutters, fixed type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all as specified and as directed by Engineer-in-Charge.

S & F 5.5mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq.m in each pane complete all as specified and as directed by Engineer-in-Charge.

M & L for 15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished rough for receiving tiles as in dado complete all as specified and as directed by Engineer-in-Charge.

M & L for preparing new plastered surfaces and applying two coats of cement base paint over a coat of suitable primer on surfaces of walls complete all as specified and as directed by Engineer-in-Charge.

M & L for 20 mm thick granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed by Engineer-in-Charge.

M & L roof tiles, Mangolare pattern, interlocking at side joints incl fixing with rendering in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

Removing building materials etc. to a distance of 4 to 5 Km upto the dumping ground as decided by the GE, beyond the lead included in the quoted rates of respective items as per SSR, including loading, unloading and stacking at the destination complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches , n exc 1.5m wide and n exc 1.5m in depth for wall foundation etc or for shaft, well, cesspits, manholes, pier holes etc n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

M & L 40mm thick Damp proof course to horizontal or vertical surface incl necessary formwork with PCC 1:2:4 type B-0 & mixing of water proofing compound as per manufacturer's instructions complete all as specified and as directed by Engineer-in-Charge.

Supply only of integral water proofing powder complete all as specified and as directed by Engineer-in-Charge.

Earth filling under floors or in foundation incl watering, ramming and consolidation complete all as specified and as directed by Engineer-in-Charge.

M & L roughly squared stone lintels, beams, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete n exc 3m in length complete all as specified and as directed by Engineer-in-Charge.

M & L stone for Chajja, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete all as specified and as directed by Engineer-in-Charge.

M & L sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

M & L for design mix RCC M-25 (20 mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and as directed by Engineer-in-Charge.

M & L for design mix RCC M-25 (20 mm graded aggregates) as in columns, pillars, piers, posts and struts complete all as specified and as directed by Engineer-in-Charge.

M & L for design mix RCC M-25 (20 mm graded stone aggregate) in slab supported on walls, beams and coloums in roofs, floors, balconies, canopies desk slabs and in selves complete all as specified and as directed by Engineer-in-Charge.

M & L for design mix RCC M-25 (20 mm graded aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter complete all as specified and as directed by Engineer-in-Charge.

Formwork to sides of pillars, posts, struts, piers,columns, and stanchions complete all as specified and as directed by Engineer-in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, complete all as specified and as directed by Engineer-in-Charge.

M & L for form work to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide complete all as specified and as directed by Engineer-in-Charge.

M & L for Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to complete all as specified and as directed by Engineer-in-Charge.

Ditto but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed by Engineer-in-Charge.

M & L for 5 mm thick cement plaster in CM 1:3 on concrete surface finished even nd smooth complete all as specified and as directed by Engineer-in-Charge.

M & L for three coats of white wash on roof ceiling including preparation of newly plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

M & L 75mm thick PCC 1:4:8 type D2 using 40 mm thick greded stone aggregate as sub base in floors complete all as specified and as directed by Engineer-in-Charge.

M & L 25mm thick PCC 1:2:4 Type-B0 using 20 mm thgick greded stone aggregate as in flooring complete all as specified and as directed by Engineer-in-Charge.

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by Engineer-in-Charge.

M & L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.

M & L Non skid coloured ceramic tiles of size 300x300x7mm thick as in flooring jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 15mm thick screeding/ bedding layer in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

M & L Glazed ceramic colour tiles of size 300x200x7mm thick as in dado/ skirting jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 10mm thick screeding/ bed plaster in CM 1:4complete all as specified and as directed by Engineer-in-Charge.

M & L cement plastering 15mm thick in CM 1:6 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for two coats of distemper oil emulsion on walls on newly plaster surfaces of walls incl preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L cement plastering 15mm thick in CM 1:4 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for two coats of cement base paint over a coat of priming coats including preparation of new plastered surfaces complete all as specified and as directed by Engineer-in-Charge.

S & F Steel windows box type with side hung shutters including projecting type hinges with steel handles and steel pay stay, complete with glazing bars/without glazing bars, dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

S & F box type steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and as directed by Engineer-in-Charge.

S & F M S Guard bars of 12mm square bars welded to steel frame of windows complete all as specified and as directed by Engineer-in-Charge.

M & L preparation of steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exec 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

S & F 3mm thick sheet glass pin headed type and glazing with oil putty in square n exec 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M & L PCC 1:3:6 type C-1 using 20mm graded aggregate as in bed blocks etc for fixing windows, doors frames or other structural section complete all as specified and as directed by Engineer-in-Charge..

S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed by Engineer-in-Charge.

S & F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per complete all as specified and as directed by Engineer-in-Charge.

Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed by Engineer-in-Charge.

M & L for Preparing new or previously untreated surfaces of wood and wood based materials of any decription exceeding 10 cm in width or girth when un-connected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over & including a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

S & F 200mm long alumimium barrel tower bolts extruded section complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs, vitreous china squatting pan “ORISSA” pattern size 580x440mm white with integral foot rests including connection to trap, and to flushing pipe, etc. complete including making good to floor alongwith flush pipe and P-trap complete all as specified and as directed by Engineer-in-Charge.

S & F wash hand basin vitreous china size 550x400mm white flat back including CP pillar tap heavy duty as approved by GE ,waste,chain plug,pvc connection, PVC waste pipe complete all as specified and as directed by Engineer-in-Charge.

S&F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe and all fitting complete all as specified and as directed by Engineer-in-Charge.

S&F PVC low level flushing cistern.valve .less, syphonic action type 10 liters capacity with inlet, ball valve, float and handle with including brackets and PVC bend pipe 90cm long complete all as specified and as directed by Engineer-in-Charge.

S&F Rotational moulded polythene water storage tank cylindrical vertical with closed top hoisted and fixed in position of 1000 ltrs capacity complete all as specified and as directed by Engineer-in-Charge.

S&F Ball valves 20mm bore high pressure of PTMT with epoxy coated alum rod and high density plastic ball screwed for iron pipe complete all as specified and as directed by Engineer-in-Charge.

S&F Bib taps cast copper alloy fancy type with crutch or butterfly handle screwed for iron pipe of 15mm bore complete all as specified and as directed by Engineer-in-Charge.

S&F towel rail 450 mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed by Engineer-in-Charge.

S & F pillar tap cast copper alloy fancy type screwed for iron pipe on both ends of 15mm bore complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs, 15 mm bore chromium plated concealed type stop valves cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified and as directed by Engineer-in-Charge.

S & F Stop cock cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 20mm bore complete all as specified and as directed by Engineer-in-Charge.

S & F Chromium plated 80 mm long shower rose with or without swivel joints, any size, incl fixing to steel pipe or union as in repairs complete all as specified and as directed by Engineer-in-Charge.

S & F 15 mm bore chromium plated angle cock cast copper allay, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes complete all as specified and as directed by Engineer-in-Charge.

S & F PVC connections 15mm size with brass nuts of length 450mm complete all as specified and as directed by Engineer-in-Charge.

S & F galvanised steel tubing medium grade 15mm bore fixed to walls or laid in floors,walls complete all as specified and as directed by Engineer-in-Charge.

S & F galvanised steel tubing medium grade 20mm bore fixed to walls or laid in floors,walls complete all as specified and as directed by Engineer-in-Charge.

S & F galvanised steel tubing medium grade 25mm bore fixed to walls or laid in floors,walls complete all as specified and as directed by Engineer-in-Charge.

S & F PVC (SWR) pipe of 100mm bore fixed to wall or laid in trenches complete all as specified and as directed by Engineer-in-Charge.

S & F PVC (SWR) pipe of 75mm bore laid in floors or trenches complete all as specified and as directed by Engineer-in-Charge.

S & F PVC (SWR) bend any radius of 75mm bore jointed with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S & F PVC (SWR) junction double (Single tee) of size 75mm bore jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S & F PVC (SWR) floor trap plain with grating including jointing with solvent cement of size 75mm outlet complete all as specified and as directed by Engineer-in-Charge.

M & L for 10 mm thick screeding in cement mortar 1:6 on concrete surfaces, finished fair & even including mixing water proofing compound as per manufacturer's instructions complete. (WPC shall be measured separately as supply only) complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing compound ISI Mark complete all as specified and as directed by Engineer-in-Charge.Make: Dr. Fixit or Equivalent.

M&L applying priming coat of cold bitumen primer at the rate of 0.40 Ltrs per Sqm as per para 11.44.5 of MES SSR Part-I incl cleaning and preparing the surface complete all as specified and as directed by Engineer-in-Charge.

M & L APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surfaces by forced application complete all as specified and as directed by Engineer-in-Charge.

M&L for Lime concrete terracing in roof with minimum thickness at edge 40 mm and increasing uniformly towards ridges to obtain a chain slope of (1:40) as described in Para 11.27.2 of MES Schedule Part-I complete all as specified and as directed by Engineer-in-Charge.

M & L for 40 mm thick brunt clay brick tiles bedded on cement mortar and joints grouted flush in cement and sand mortar (1:3) mixed with integral water proofing compound IS 2645 : 2003 @ 3% by wt of cement complete all as specified and as directed by Engineer-in-Charge.

M & L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.

M & L plinth protection 75mm thick PCC 1:3:6 C1 on 75mm thick PCC 1:5:10 E2 on rammed earth complete all as specified and as directed by Engineer-in-Charge.

S&F for 15 mm bore chromium plated with long shank and cup (conncelaed type) stop cock screwed down high pressure, with capstan head, screwed both ends for iron pipe or for union complete all as specified and as directed by Engineer-in-Charge.

M & L for PCC 1:3:6 type C-1 using 20 mm thick greded stone aggregate in chowkhats filling complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches , n exc 1.5m wide and n exc 1.5m in depth for wall foundation etc or for shaft, well, cesspits, manholes, pier holes etc n exc 10 sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:4:8 Type D2 using 40 mm thick greded stone aggregate as in foundations,filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

M&L cement plastering 15mm thick in CM 1:4 on other than fair face of brick work surface finished even & smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete all as specified and as directed by Engineer-in-Charge.

M&L concrete bed to drain pipe in PCC 1:4:8 type D2 using 40mm graded stone aggregate incl packing under and hunching against sides of pipe after they are laid on slope and tested for 150mm dia bore sewer pipe line ( earth work excavation and sewer pipe line will be measured and paid separately) complete all as specified and as directed by Engineer-in-Charge.

Supply and laying salt glazed stoneware pipe confirming to IS 651-1972 in tranches and jointed in cement mortar 1:1 complete all as shown on drawings for 150mm internal dia of pipe ( excavation and earth work measured separately) complete all as specified and as directed by Engineer-in-Charge.

M & L precast cement concrete but in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces Type B1 1:2:4 (20 mm graded aggregate Set in Cement Mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully (aluminium) point wiring complete of any type (batten/ surface conduit or concealed) for light point, fan point, bell point socket point or power point complete with all fitting such as switches, sockets pendants, ceiling rose, round block etc complete and making good disturbed surfaces of wall, floor or ceiling with plaster of tiles or roof treatment etc and finishing the surfaces with distemper/white washing/colour washing to match with the existing surface complete all as specified and as directed by Engineer-in-Charge.

Taking down submain wiring Aluminium/ copper of any size including earth continuity condutor on teak wood or conduit and removing from site and making good the disturbed surface of wall complete all as specified and as directed by Engineer-in-Charge.

Taking down old U/S existing DB TPN 4 way and DB SPN 8 way including MCB/MCCB of any capacity and any size and removing from site and making good the disturbed surface of wall complete all as specified and as directed by Engineer-in-Charge.

M & L for point wiring with and including single core FRLSH PVC insulated and unsheathed stranded copper conductor cable of size 1.5 sqmm 1100 volts grade drawn through and including suitable size of PVC concealed conduit with accessories with laminated top cover fixed on GI sunken box with modular cover plate for housing of switch, socket, regulator etc complete with and including 1.5 sqmm FRLSH PVC insulated and unsheathed stranded copper conductor cable as earth wire and connected to common earth dolly and making good to the disturbed surfaces of wall, floor, ceiling etc to match with exisiting surface complete all as specified and as directed by Engr-in-Charge for the following :-

(a) One Light/fan/ex-fan/Bell/point controlled by one switch.

(b) One pin 5 amps socket point on the same board with other switches complete

(c) One 3 pin 5 amps socket on independent board.

Ditto all as per item No 274 above but with 4.0 sqmm copper wire for 3 pin socket outlet 15 Amp on independent board complete and all as directed by Engr-in-charge.

S&F switch Modular type, 6 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

S&F switch Modular type, 16 Amp, 1 module single pole one way, 230 Volts, Modular type complete all as specified and as directed by Engr- in -charge.

M&L socket outlet 3 Pin 6 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

M&L socket outlet 3 Pin 6/16 Amps modular type, 2/3 pin combined 2 module 230 Volts complete all as specified and directed by Engr-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.

S&F ceiling rose, surface backelite , three terminal AC, 230 volt complete all as specified and as directed by engineer-in-charge.

Supply and fixing fan step regulator modular type,120W -2 module electronic socket type five step controlled 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Supply and fixing Bell push, flush type, 5 amp 230V AC 50 Hz for complete all as specified and directed by Engr-In-Charge.

Supply and fixing Buzzer, Ding Dong AC. 230 volts, single pole complete all as specified and directed by Engr-In-Charge.

Supply & fix LED bulk head ,09W / 10 W, IP65 diacast aluminium housing powder coating finished > 0.9 complete all as specified and directed by Engineer-in-charge. Cat Part no. SSk-BH-9W in make Syska / havell's / Phillips.

Removing and Refixing LED tube light fitting, 1x 20-22 watts, 230 volt, basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver, pre-wired and fixed on walls with all fixing accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by engineer-in-charge.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed by engineer-in-charge.

S&F sheet metal enclosure MCB DB, double door, vertical TPN 4 way with 200 Amps rated busbar complete all as specified and as directed by engineer-in-charge. Make:- Hegar/Legrand/Seimens

S & F double door, sheet metal enclosure, powder coated for MCB DB SPN 8 way fitted with neutral link, earth bar , din rail and 200 amps rated bus bar 230 volt conforming to IS 13032-1991 complete all as specified and as directed by Engr-in-charge.

S & F MCB SP, 5-32 Amps , 240 volts, breaking capacity 10KA complete all as specified and as dircted by Engr-in-charge.

S & F MCB DP,D CURVE 40 Amps , 240 volts, complete all as specified and as dircted by Engr-in-charge.

S&F MCB 63amps, C curve TPN, 415 volts, complete all as specified and as directed by Engr-in-charge.

M&L for submain wiring using 2 runs of single core FRLS PVC insulated, unsheathed stranded copper conductor cable of size 2runs of 6 Sqmm of voltage rating 1100V for Single phase & neutral, drawn in and including concealed PVC conduit of dia not less than 25 mm dia with standard acessories, along with two run of FRLS PVC insulated, unsheathed, stranded copper conductor of size 2x 6.0 Sqmm as earth continuity conductor all as specified and directed(Note-2 runs of single core FRLS PVC cable 6sqmm for Single phase & neutral with Two run of earth conductor as earth and conduit shall be measured as one unit) complete all as specified and as directed by engineer-in-charge.

Taking dowen and refixing tamper proof energy meter electronic type single phase 10-60 Amps current rating single phase 230V AC with electric connection and necessary fixing arrangement complete all as specified and as directed by engineer-in-charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed by engineer-in-charge.

Taking down fan,sealing cable end,dismantling blades and removing fan and blades & refixing ceiling fan of any make, any sweep , keeping side in store in safe custody for painting of ceiling fan complete,in situ with synthetic enamel paint by spraying including filling cavities with filler,one coat after cleaning all dust and reassembling the fan complete including writing MES No at the site complete all as specified and as directed by engineer-in-charge.

Taking down Geyser of any capacity from wall complete all as specified and directed by Engineer-in-Charge.

Refixing of geyser with including fixing arrangement complete all as specified and directed by engineer-in-charge

Excavation in trenches n. exc 1.5 m in depth and not exc 1.5 m width for laying of cable lines etc and getting out in hard/ dense soil complete all as specified and as directed by engineer-in-charge.

Supply and laying Sand coarse dry as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 cm (15 cm under the cable & 8 cm over the cable) and gently punned down to 18 cm thickness complete all as specified and as directed by engineer-in-charge.

Supply and laying bricks (old size) for cable protection by using common burnt clay building bricks, sub-class ‘B’ designation 75 laid dry flat across length of the cable with width of the trenches equal to length of bricks complete all as specified and as directed by engineer-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10sq mm 2 core complete all as specified and as directed by engineer-in-charge.

S&F GI tubing light grade 40mm dia for protection of cable on pole/ wall etc complete all as specified and as directed by Engr in charge.

S&F GI bracket made out of 40 mm bore GI pipe light grade /medume grade, ISI marked, medium grade 1.2m long bent to shape suitable for fixing of street light fitting including with 2 Nos MS clamps made with 40x3mm flat iron, bolts, nuts, washers etc including two coats of synthetic enamel paint over one coat of zinc chrome primer and fixing on electric pole complete all as specified and as directed by Engr-in-charge.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meters below normal ground level connecting to the galvanised earth lead wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanized iron and steel earth wire protected by provision of GI mediumgrade pipe 15mm bore including provision of concrete pit made with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4Kg/Sqm) and frame of angle iron 40x 40x6 mm and handle of 6mm dia MS bar made to shape, GI light grade 20mm bore pipe for watering perforated at bottom, 1.75meter long placed on top edge of earth plate, common salt & charcoal filling with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returing filling in and removal of surplus soil to a distance not exceeding 50 meters all as per electrical plate No -5 of SSR 2009 Part-I and connecting to Lighting protection earth test points all as specifed and directed including testing on completion.

S&f Switch piano flush type single pole, one way 15/20 Amps 230 Volts complete all as specified & directed by Engr-in-Charge.

M&L for socket outlet 2 in 1, 3 Pin, 5 & 15 Amps, 230 Volts t complete all as specified & directed by Engr-in-Charge.

Supply and fixing LED mirror light fitting , type with high out put diffuser 2 feet, 5watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by engineer-in-charge. HAVELLS CAT PART NO-ENDURALINEARNEOBS10WLED865SPCWH/WIPRO CAT PART NO-LL20-111-XXX-65NE3/BCLSB 10 WH

M&L and jointing GI tubes, medium grade 25mm dia in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in trenches complete all as specified and directed by Engr-in-charge .

Supply & Fixed on walls and ceiling or laid in floor/in tranch and jointing GI tubes, 20 mm dia medium grade in lengths with screwed and socket joints together with all galvanised steel fittings such as bends, elbows, tees, union, short pieces, connectors, check nuts, caps, plugs etc fixed complete laid in wall complete all as specified and directed by Engr-in-charge .

Cutting existing steel tubing for alterations or additions done in position without taking down for 100 to 40mm dia pipe (Each cut measured) complete all as specified and as directed by engineer-in-charge.

S&F Gun metal gate valve 20mm bore with iron wheel head screwed both ends for iron pipes complete all as specified and as directed by engineer-in-charge.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6sq mm 2 core complete all as specified and as directed by engineer-in-charge.

NARAYAN SINGH NARENDRA SINGH AND COMPANY