SPL REPAIRS TO BLDG NO. TO 28/3 AND 4 AT SOMNATH ENCLAVE IN SUKNA MIL STN AND OTHER SANCTIONED WORKS AT SUKNA MIL STN OF AGE B/R II UNDER GE SUKNA

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, LT under ground cables/ GI pipes for trenches etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning filling in and ramming earth in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good in soft/loose soil complete all as specified and directed.

M&L for earth filling under floors, spreading and levelling in layers not exceeding 25 cm thick and well ramming including watering as required complete all as specified and as directed. Note:- Earth obtained from excavation after cleaning shall be reused in this item.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or broken boulders complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L PCC 1:2:4 type B-1, (using 20 mm graded crushed stone aggregate) as in sunken portion and including demolition complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, wall of drains, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc and setting in mortar joints to match complete all as specified and directed.

M&L for Precast Reinforced Cement concrete 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) in 25 mm thick (measured solid) Jallies or louvers including all mouldings set jointed in CM 1:4 but excluding frame including demolition of existing cement concrete complete all as specified and directed. Note : Precast frame shall be measured separately and paid separately under respective item

M&L for Reinforced Cement Concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, deck slabs and in shelves and the like complete all as specified and directed.

M & L for Reinforced cement concrete ,1:1.5:3, Type A-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Supply only integral water proofing compound complete all as specified and directed.

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and directed.

M & L for brick work with sub class ‘B’, old size brick straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L cleaning the surfaces of sunken floor using wire brush, brooming down and washing down with water to remove dust etc. and including brushing with neat cement slurry @ 0.5 kg / sqm & one coat with acrylic based polymer modified cementitous composite @ 0.50 kg / sqm complete all as specified and directed.

M&L for Brick work with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M & L for 25 mm thick cement concrete 1:2:4, Type B-0 using 12.5mm stone aggregate as in damp proof course to horizontal or vertical surfaces including necessary form work with polythene film 150 micron thick laid on a coat of bitumen primer @ 0.30 to 0.50 kg per Sqm as in damp proof course complete all as specified and directed.

S&F Polythene film, 150 micron thick, laid over and including on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting n.exc. 10 cm in girth complete all as specified and directed.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade over 20 mm thick screed bed in CM (1:6) complete all as specified and directed.

Use and waste of formwork to chullah, soffits of suspended slabs, chajjas, etc such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F 2nd class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 Sq.cm and not exceeding 13 Sq.cm complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkhats complete all as specified and directed. Species of timber :- Gamari (Gnelina arborea) / Chickerassy (Chukrasia Tabularis) / Siris (Albizzia procera) / Kalasiris (Albizzia Odoratissima)

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

Taking down chowkats or frame n.exc 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frame but exc. 1.5 Sqm but not exc. 4.0 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with MDF board and plywood faces panels, commercial type on both side complete all as specified and directed

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S&F factory made solid panel moulded PVC door shutter with particle board core 30mm thick (stiles) with 2 panel design with 2mm thick moulded PVC sheet on, 4 consisting of frame made out of MS tubes for top & bottom rails, MS frames shall be covered with heat moulded plain colour PVC 'C' channel, the front face & 2mm plain colour PVC sheet on back face in frame at site as per specifications and drawings complete all as specified and directed. Make:- M/s Jain Doors Pvt Ltd (Woodify) / M/s Sylvan Plyboard (India) Pvt. Ltd (Sylvan Ply) / M/s Sri Bhawani Plyboard Industry / M/s A-1 Teak Products Pvt Ltd / M/s Vidya Ply & Board Pvt Ltd / M/s SA Plywood Industry (P) Ltd (GLOBE) / M/s Archidply industries ltd

S & F of 150 mm long Aluminium anodised barrel tower bolts, of extruded section complete all as specified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S&F 30mm width, brass continous piano hinges, bright finish or electrogalvanised complete all as specified and directed.

S&F in repair 300 mm, ordinary rat tail rod pattern springs and including roller and roller plate complete all as specified and directed.

M&L chromium plated stainless steel, fancy handle of size 100mm long complete all as specified and directed.

S&F 150 mm long extruded aluminium handles, fabricated type, anodised and fixed complete all as specified and directed.

S&F 150 mm hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed.

S&F in repairs decorative curtain rod of wooden finish powder coated of 25 mm dia including 06 nos. curtain ring per running metre complete all as specified and directed.

S&F in repairs decorative type wooden finish double brackets support for holding curtain rods and corner to be fixed to ends of curtain rod fixing with screws complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe – 290 Gde E -- 165 complete all as specified and directed.

M & L for mild steel TMT bars 6-8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F joints, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Structural steel work of angle, channel etc., confirming to Fe 410 -W (Gde- E- 250) complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including one shop coat of zink chromate primer paint complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S & F Steel ventilator with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

M&L powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

M&L Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and directed as per architectural drawings and the directions of Engineer-in-Chief.

Supply and fix for powder coated aluminium shutter weight 0.55 Kg per meter including necessary joints cleats,rubber beading/glazing clips,rubber neoprean packing handles two nos for each door hinges anodised aluminium snap beading screws etc. complete all as specified.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws of any descriptions complete all as specified and directed.

M&L in repairs for 18/19 mm thick coloured prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination kitchen CB drawer, Cup boards cabinates etc complete all as specified and directed.

S&F telescopic channels powder coated with ball bearing minimum 60 cm long standard width fixed over and including 2nd class hard wood fillet section area exc. 3 sqcm and not exc. 6 sqcm clean swan secured with screws complete all as specified and directed

M&L 50 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in footpath/ hard standing/pavings/plinth protections, finished even and smooth using extra cement including spike rolling to making impression of expended metal, while the concrete is green complete all as specified and as directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L 100 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sunken portion/ laid above PCC sub floor / correction layer /under layer and including demolition of old concrete complete all as specified and directed.

M&L for repair of damaged roof after complete removal existing treatment including padding, cleaning the surface using wire brush brooming down and applying the following treatment all as directed in order of precedence as stated :- (i) Rendering 15mm thick in CM (1:4) on existing roof surface true to level after applying cement slurry @ 3Kg/Sqm. ii) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (Note :- Bituminous primer shall be `TANK MASTIC’ manufactured by M/s STP Ltd or “EMUFALTE” manufactured by M/s Texsa India Ltd) (iii) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.60 Kgs per Sqm reinforced with non-woven polyester febric weight not less than 150gms per Sqm. Polymeric membrance shall be taken to a height of 30cm(minimum) and than inserted inside the groove of parapet wall and shall be finished by a membrance flashing. (iv) Two coats of aluminium paint on APP membrane. Note :- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions.

(ii) A minimum overlap of 100mm and 75mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. iii) APP based polymeric membrane shall be “SUPER THERMOLAY” manufactured by M/s STP Ltd or “ MOPLY FP 3mm” manufactured by M/s Texsa India Ltd & equivalent of Shivam Tar product. (iv) The finished shall be given Aluminium Paint as per manufactures instruction.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

M&L coloured glazed ceramic tiles 450 x 300 x 7 mm thick as in dado / skirting and vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing coat with CM 1:3 including roughening of surface complete all as specified and directed.

M&L 10 mm thick vitrified ceramic tiles light shade (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces / ceiling, racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surface using water proofing compound as per manufacturers instructions finished even and smooth with Neeru Finish complete all as specified and directed.

M & L for 15 mm thick rendering internal wall in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finished the surface even and fair without using extra cement complete all as specified and directed.

M&L 5 mm thick rendering in CM 1:3 on fair faces of brick work or concrete surfaces as in ceiling, chajja, soffits etc, and finished even and fair without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and fair without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L 10 mm thick rendering in CM 1:3 in sunken portion, using water proofing compound as per manufacturers instructions finished even and fair including taking down complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparing newly plastered walls surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of exterior weather coat paint over a coat of primer complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall/ceiling surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of weather coat exterior apex paint over a coat of primer complete all as specified and directed.

M&L finishing walls with acrylic smooth exterior paint of required shade : new work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

S & F 3 mm thick frosted glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F 4.8mm thick glass including tinted/dark film n exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of old decorated wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking up or down for 15 mm bore pipe, steel water tubing including disconnection of fittings from tubing etc complete and making good disturbed surfaces of walls /ceiling etc complete including staking aside for refuse and removal of unserviceable items from site complete all as specified and directed.

Taking up or down for 20 mm bore pipe, steel water tubing including disconnection of fittings from tubing etc complete and making good disturbed surfaces of walls /ceiling etc complete including staking aside for refuse and removal of unserviceable items from site complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs of 110 mm bore PVC (SWR) branch piece, Single (Single ‘Y’) equal or unequal complete all as specified and directed

S & F in repairsof 110 mm bore PVC (SWR) junction Double, (cross ‘T’) equal or unequal complete all as specified and directed

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs kitchen plate rack made out of 1.0mm stainless steel sheet & of size not less than 90cm x 90cmx25cm, standard quality fixed with brass screw complete all as specified and directed.

S&F in repairs vitreous china european wash down water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550x400mm with and including unplasticised 32 mm bore PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, in floors etc, 32mm bore, waste coupling and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repair PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S & F 15 mm bore Stop valves, fancy type chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs 15 mm bore Stop valves/ angular stop cock, fancy type chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F angle stop cock 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, chromium plated long thread with flange complete all as specified and directed.

S & F in repairs of 15 mm bore bib tap long body, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15 mm bore bib tap chromium plated fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F in repairs , 3 hole basin mixer without popup waste system complete all as specified and directed. Make: Jaquar/ MARC/ CERA

S&F in repairs , wall mixer non telephonic complete all as specified and directed. Make: Jaquar/ MARC/ CERA

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for hot water supply complete all as specified and directed.

S&F 75 mm dia Stack clamps out of 50 mm x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors/ trenches etc complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls/ floors/trenches etc complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) 75 mm bore bend with access door, of any radius complete all as specified and directed.

S&F in repairs health faucet 15 mm bore, ABS chromium plated with & including 1.0 mtr chromium plated flexible tube & wall hook including CP nipple and socket complete all as specified and directed.

S&F in repairs bathroom cabinet of size 445x380x95 mm made out of 2mm thick acryllic sheet with internal shelves and openable shutters including 10mm dia aluminium/brass CP rod complete all as specified and directed.

S & F in repairs Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated brackets guards and railing 60 cm long complete all as specified and directed.

S & F in repair sheet glass 5.5 mm thick corner shelf assembly 12cm wide with CP bracket guard and SS railing complete all as specified and directed.

S&F towel rail 20 mm dia & 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repair towel rail 20 mm dia & 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F CP soap dish metal dish, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F 100mm dia stainless steel gratings, doom type, chromium plated, with or without waste hole, fixed to floor trap complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of existing WC floor and including PCC / tile flooring, traps attached to WC, lean concrete, plaster and removing all the debris complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Taking down copper / aluminium concealed point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc., removing materials to store for keeping in safe custody or for taking credit, cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down copper / aluminium concealed sub main wiring complete with all fixture and fittings including cutting chasing as required and making good the disturbed surfaces including finishes to match with adjacent surfaces of walls, floors, etc. complete all as specified and as directed.

Taking down old unseviceable DB with MCB/RCB/Isolator any size and any capacity complete all as specified and as directed.

M&L for point wiring for light points / fan points controlled by one, one way switch with (FRLSH) PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm, with PVC insulated unsheathed stranded copper conductor cable of size 1.5 Sqmm stranded for earth continuity wire, to be drawn in and including , PVC medium grade concealed conduit not less than 20mm dia with modular flush box, modular plate and frame all necessary wall cutting and making good disturbed surface complete all as specified and as directed.

All as per item No 140.00 here-in-before but for 5 pin 15 Amps switch socket combination on independent board with 2.5 Sqmm cable for phase neutral and earth complete all as specified and directed.

All as per item No 140.00 here-in-before but for 3 pin 5 Amps S/Socket pt. on independent board with 1.5 sqmm cable for earth, neutral and phase complete all as specified and directed.

All as per item No 140.00 here-in-before but for 3 Pin socket outlet 5 Amps same board with other switches with cable 1.5 Sq mm size complete all as specified and directed.

S & F Modular type switch piano 6 Amps single pole one way one module complete all as specified and directed.

S & F Modular type switch piano 16 Amps single pole one way one module for 16A independent complete all as specified and as directed.

S & F modular type Socket outlet 6 Amps 2/3 pin combined 2 module complete all as specified and as directed.

S & F modular type Socket outlet 16 Amps-2/3 pin combined 2 module complete all as specified and as directed.

S & F for ceiling rose surface Bakelite 65 x 50mm three terminal complete all as specified and directed.

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole incluing taking down old unserviceable ones complete all as specified and directed.

S & F Switch piano 5 Amps single pole bell push incluing taking down old unserviceable ones complete all as specified and as directed.

S & F modular type electronic fan regulator flush type 230V, AC, 50 Hz not less than 100 W complete with connection complete all as specified and directed.

M&L for MCB SP 6A, 230V, 50 Hz, compatible for DIN rail "C" series In accordance with IS/IEC 60898-1-2002, 240 V, 50 Hz, 10 kA Suitable for Inductive loads complete with connection complete all as specified and directed.

M&L for MCB SP 10A-20A, 230V, 50 Hz, compatible for DIN rail "C" series In accordance with IS/IEC 60898-1-2002, 240 V, 50 Hz, 10 kA Suitable for Inductive loads complete with connection complete all as specified and directed.

M&L for MCB SPN 32A, 230V, 50 Hz, compatible for DIN rail "C" series In accordance with IS/IEC 60898-1-2002, 240 V, 50 Hz, 10 kA Suitable for Inductive loads complete with connection complete all as specified and directed.

M&L for single pole blanking plate for distribution board complete all as specified and directed.

Supply and fix MCB protected POWER UNIT with one 25 amps socket, (incl 3 Pin Plug Top) including MCB DP and starter 25 Amps rating with six module plate and flush PVC box and electrically connecting up fixed complete all as specified and directed. Make Havells cat No- DHDUCDP0253016-25 (25 Amps) OR any equivalent model in Legrand / L & T.

Supply and fixing distribution board (DB) SPN 12 ways, with neutral and earth bus bar 200 A rating 230 Volts, single door, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and as directed by the Engr-in-Charge.

M & L concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L concealed sub main wiring with 2 runs of 4 sqmm main wire along with 1 run of 4 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length. Make of cable:- Havells / KEI / Polycab / RR Kabel Ltd. / HPL Make of PVC Conduit:- Richa Cables / AKG Industries / Harsh Electro Systems / Panasonic (Anchor)

M & L concealed sub main wiring with 3 runs of 6 sqmm main wire along with 1 run of 6 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

Supply and fix in repairs of surface & wall mounted LED decorative bracket light fittings with 9/10 w indoor luminaries with and including Electronic driver and LED lamp, pre-wired including necessary electric connection from ceiling rose to light fitting, conforming to the following specifications: - (i) System Watts/lumens: - 9 to 10 W/Total system lumen not less than 800 Lm. (ii) Housing: - Extruded polycarbonate/engineering plastic (iii) IP rating: - IP 65 (iv) Front cover: - PRISMATIC DIFFUSER. (v) Mounting: - Suitable for wall/ceiling mounting (vi) Finish: - Smooth finish (vii) Lamp: - SMD LED high bright (viii) Heat sink: - As per OEM's design

Supply and fix in repairs recess mounted LED down light fittings square type with 12 w indoor luminaries with and including Electronic driver and LED lamp, pre-wired including necessary cutting of ceiling and making good, electric connection to light fitting, conforming to the following specifications :- (i) System Watts/lumens: - 12 W/Total system lumen not less than 1200 Lm. (ii) Housing: - Extruded aluminium (iii) IP rating: - IP 20 (iv) Front cover: - Acrylic/polycarbonate cover frosted (v) Mounting: - Suitable for ceiling recess mounting (vi) Finish: - Smooth finish (vii) Lamp: - High bright LED (viii) System Efficacy (lm/Watt): - Not less than 100 lm/watt (ix) Colour temperature: - Not less than 5700 K (x) Colour rendering index (CRI): - Not less than 80 (xi) Life: - Not less than 25000 hrs of operation (xii) Optics: - Designed for optimum light distribution (xiii) Control gear: - Inbuilt electronic driver with APFC, PF not less than 0.95, and THD not more than 20% of the standard operating voltage 180-270V Ac, 50 Hz (xiv) Surge protection: - Inbuilt surge protection minimum 2 KV (xv) Heat sink: - As per OEM's design

Supply and fixing in repairs of decorative wall mounted bathroom light fittings complete with moisture proof sealed fittings and not less than 9W high bright LED with B22 socket type complete all as specified and directed by the Engr-in-Charge.

S&F PVC exhaust fan 250mm sweep, nonmetallic blades with louver shutter, single phase heavy duty grey in colour all accessories with the provisioning rag bolts, nuts, washers etc. Any disturbed surfaces of wall shall be making good by cement work/plastering and matching by existing colour white/colour wash as well as writing the MES No with white colour paint including connection complete all as specified and directed by the Engr-in-Charge.

S&F Exhaust fan for ventilating porpose AC single phase 230/240 V of size 300 mm sweep with metal body and metal blades grey in colour complete all as specified and directed.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed. Make : Havell Monza DX Model No. GHWAMGTWH025 or equivalent in V-Guard/ Crompton Greaves/ Usha/ Jagaur

S&F Lamp holder, PVC/ polycarbonate type with cord grip cap suitable for pendate fittings including taking down old unsv ones complete all as specified and as directed.

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficeacy: - Not less than 120 Lm/Watt including taking down old unsv ones complete all as specified and directed.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. (Cat ref LUMILINEPLUSBS20WLED865SPCSS of Havells or Cat ref LDL-20-CDL of Crompton or Cat ref BCLSB 20W WH of Bajaj).

S & F in reapir Surface and wall mounted LED batten 10 watt 2ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 2200 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. (Cat ref. LUMILINEPLUSBS10WLED865SPCSS of Havells or Cat ref LDL-10-CDL of Crompton or Cat ref BCLSB 10W WH of Bajaj).

S & F in repair LED Street Light 20 watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy ≥100 Lm/W, 5 kV Surge Voltage Protection,Operating Voltage range 140 V - 270 V complete all as specified and as directed. (Cat Part No.ENDURAPEARLSL20WLED757SASYTOPCMP of Havells or Cat ref LSTS-20-CDL-M of Crompton or Cat ref ENXT P 24L WH CR PC SD of Bajaj).

S&F in repair of energy saving BLDC ceiling fan without remote Type of motor: - Brush Less DC Motor (BLDC) and Input Power: - 26 to 32 watts with full speed and reduced power consumption with reduced speed technology and RPM: - 340 to 375 rpm and Sweep: - 1200 mm and Air delivery: - Not less than 210 CMM and Colour: - Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge and peed/power contro. (Old unserviceable fan shall be deposited to MES store. Labour cost for the same is deemed to be included in the item rate) complete all as specified and as directed

S&F VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-43 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 250+24 complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as directed. Make: Cat ref 507759 of Legrend/L&T or equivalent.

S&F MCCB 4P 125 Amps 415V ,50 Hz ,breaking capacity 16 KA . Including dismantling taking down unsvericeable one complete all as specified and drected by Engr-in -Charge.

Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead wire of 4 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge.

supply and fixing TV socket complete all as specified and drected by Engr-in -Charge.

S&F PVC conduit 20mm dia (for lan cable/TV cable) complete all as specified and drected by Engr-in -Charge.

M/S GLORIOUS CONSTRUCTION

MS ORIENT ENGINEERING WORKS

SHRI ARUN BHATTACHERJEE

VICKY ENTERPRISES

MS ESSCON

A K ENTERPRISES

M/s T K Das

ASHISH ROY