GE 874/EWS-55/2020-21

Amount

B/R Portion

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Taking down cement plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Dismantling of timber scantling 40sqcm and over in section unframed work, as in any position, complete all as specified.

Demolition of brick or stone masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles all as specified.

Walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4, complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface not exceeding 40mm to face stones (lime and sand stone) and dressing of face beds and joints, complete all as specified.

2nd class soft wood as in scantling, clean sawn, timber framed and fixed in position with nails complete all as specified and directed.

Second class softwood as in scantling, clean sawn fixed in position but except wood complete, all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, all as specified and directed.

0.63mm thick galvanised corrugated mild steel sheeting with Zinc coating of 120 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with coach screws and washers in roof, walls etc complete all as specified and directed.

Fixing only galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with new coach screws with bitumen washers, in roofs, walls etc complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed.

Hard core of broken stone/boulders of gauge exc 63mm deposited spread and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

Plain cement concrete 1:2:4 type B-2 (using 20mm graded crushed stone aggregates) as in hardstanding / pavements of flexural strength 40 kg/sqcm in field using 400 kg of cement per cumic meter thickness concrete 25 cm or less (150 mm thickness), laid in panels and finishing the surface even and fair without using extra cement including use of formwork and making joints and rounding or chamfering exposed edges complete all as specified and directed.

RCC type B1 1:2:4 (using 20 mm graded aggregate), as in slab supported on walls, beams and columns in floors, roofs, landing balcony, canpoies, deck slab and in shelves and the like complete all as specified.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

Form work to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work complete all as specified & directed by Engineer-in- charge.

Form work to edges of concrete flats, breaks in floors, openings in concrete walls. Floors, and roofs and RCC/PCC bands in walls, horizontal or sloping, and similar work complete all as specified & directed by Engineer-in- charge.

PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation, filling mass concrete/surface channels and drain complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified.

Extra for forming fair finished drain or channel over 30cm inner girth upto 55cm in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified.

40mm thick PCC (1:2;4), type B-0 using 12.5 mm graded crushed stone aggregate as in sub base for laying floor finishes such as tiles etc complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 20mm thick screed bed in cement mortar 1:6 complete.

Machine cut kota stone slab as in riser of steps, skirting, dado and pillar, 20-25mm thick laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished even and smooth without using extra cement including filling the joint with mastic filling comprising 3 parts of sand & 1 part of heated bitumen 85/25 grade (by weight) all as specified.

PCC 1:2:4, nominal mix, type B-1, using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified & directed.

Rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick work finished even and smooth (without using extra cement) complete all as specified and directed.

Rendering 15mm thick in Cement Mortar 1:4 on other than fair faces of brick work or stone work surfaces finished even and smooth (without using extra cement) complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails (in floor etc).

20mm thick, second class soft wood boarding, planed one side, with butt joints and fixed with nails in facia, eaves boarding,(except flooring and skirting) complete all as specified and directed.

All as per item No. 30 Abobe but except boarding.

Two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new or previously untreated steel surfaces of any description with mordant solution including washing and cleaning etc not otherwise described, over 10cm width or girth, complete, all as specified and directed by Engr-in-charge.

One coat of synthetic enamel paint including preparation on old galvanised steel surfaces complete, all as specified and directed.

Two coats of synthetic enamel paint over a coat of pink primer on new wooden or plywood surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete, all as specified.

One coat of synthetic enamel paint including preparation on old painted wooden or wood base surface of any description, not otherwise described over 10cm width or girth, complete, all as specified and directed

Preparation of new plastered surface of walls including cornices plaster etc, and applying two coats of cement base paint over a coat of approved primer, complete all as specified and directed.

Preparation of old plastered or unplastered surface of walls including cornices plaster etc, and applying one coat of cement base paint complete all as specified and directed.

Taking down chowkhats of frame exc 1.5 sqm and n. exc 4 sqm each with shutter (without taking off shutters of the frame), complete all as specified.

Taking down chowkhats of frame n.exc 1.5 sqm each with shutter (without taking off shutters of the frame), complete all as specified.

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

30mm thick flush shutter solid core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc.supplied and fitted to chowkats, 30mm thick shutter as specified in SSR Part -I section -8, clause8.24 (b) for window etc complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, ISI marked complete all as specified.

Mild steel butt hinges, medium weight, cold rolled, 75mm long, ISI marked complete all as specified.

200mm long Aluminium alloy, anodised, barrel tower bolts of extruded section ISI marked.

125mm long Aluminium alloy, anodised, barrel tower bolts of extruded section ISI marked.

250mm long aluminium alloy, anodised, sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section and fixed, all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets.

Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples fixed in repair, complete all as specified.

Plain fillets, rectangular or triangular in section clean sawn, secured with nails or brads 3sqcm & not exceeding 6sqcm, second class soft wood (Kail) complete, all as specified.

Plywood BWR type BB( Nos of ply-5 Nos ) fixed with nails to timber frame /existing ceiling and wall lining (As applicable ) 6 mm thick complete all as specified and directed.

E/M Portion

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings, removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Points wiring for one light point/fan/socket point controlled by one switch with 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including PVC casing and capping (ISI marked) including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

Point wiring for 3 pin socket outlet 5 Amps on same board controlled by one switch with 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi strand flexible cable and 1.5 sqmm FRLS insulted un-sheathed copper conductor single core multi stranded flexible cable as earth lead (using colour coding) in and including cable 1100 volts grade including casing and capping (ISI marked) including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover including cutting chases to wall making good the distrubed surfaces to match with the existing specification complete all as specified.

All as per description all as per item No. 55 here in before, but for 3 Pin socket outlet 5 Amps point on Independent board, with cable 1.5Sqmm size, insulated copper conductor cable 1100 volt grade with continuous PVC insulated copper conductor cable of 1.5 Sqmm, complete all as specified and directed.

All as per description all as per item No. 55 here in before, but for 3 Pin socket outlet 5 Amps point on Independent board, with cable 2.5Sqmm size, insulated copper conductor cable 1100 volt grade with continuous PVC insulated copper conductor cable of 1.5 Sqmm, complete all as specified and directed.

Decorative LED batten for surface and pendent application. Anodized extruded aluminium housting high transmisitivity diffuser, high lumen output of VIVA MINI LED Luminaires (4FT) of 20 Watt connecting up with twin core twisted flexible copper conducter cable of suitable size complete all as specified and directed.

LED light fittings 1X9 W bulk head luminaires etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230 volt 50 HZ make Havells, Bajaj, Phillips complete all as specified and directed.

Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified.

Ceiling rose, PVC/poly carbonate, isolated body three terminal complete all as specified and directed.

Switch Socket combination 2 in 1, 5 and 5 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

Switch Socket combination 5 in 1, 5 and 15 Amp flush type universal controlled by one switch (ISI Marked) complete all as specifed and directed.

Socket outlet 2 in 1, 5 pin, 5A, flush type universal, all as specified and as directed. Make:Havells/Anchor

Rectangular boards/ blocks 30x25x4cm depth closed recessed, complete all as specified and as directed by Engr-in -charge.

Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 ways with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/lEGRAND/SSK

1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 16Sqmm, complete all as specified and directed.

House service bracket (hook type), complete, with 3m long GI pipe 40mm dia medium grade, two Nos 90 degree bend, MS hook and guy or stay, complete all as specified.

RCBO, singal pole and neutral 240 VOLT 50Hz 10 Ka, 6/32AMPS all as specified and directed. Make havelles CAT part NO DHCEACSN2030006 to 32/Legeands/PHilips.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI medium grade water pipe 20mm dia with funnel all as shown in electric plate No. 03 of 2009 SSR Pt-I and testing on complete including earth work in any type of soil, PCC 1:2:4 as in eartig pit CI pit cover 5.5mm thick common salt charcoal all as specified.

Lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

Supply and fixing in replacement LED lamp energy saving 9W LED lamp 6500 K Make Suriya or equivalent in Crompton greaves, Bajaj

Supply and fix Voltage stabizler for automatic operation, single phase naturally air cooled indore type & designed for input variation between 110 v to 190 V with output voltage stabilzed at 23 V with accuracy of plus or minus 2.5 % 4-6 Sec initial delay and capasity 6.6KVa/30 A Make V-Guard model No VGMW1000PLUS OR Equivalent as approved by Engr-in charge.

M/S ASMATULLAH SHAH

POPULARHARDWARESTORE

M/S MANZOORAHMAD LONE

M/S AKHLAQ ENTERPRISES

M/S MATOO INFRASTRUCTURES PVT. LTD.

Bidder Name

M/S ASMATULLAH SHAH

POPULARHARDWARESTORE

M/S WANI CONSTRUCTION AND CO

M/S MANZOORAHMAD LONE

M/S AKHLAQ ENTERPRISES

M/S MATOO INFRASTRUCTURES PVT. LTD.