REPAIRS AND CLEANING OF SEWAGE LINE, MANHOLE AND REPAIRS TO PATH, COMPOUND WALL, GATE FENCING, HARD STANDING DRAIN AND DAY TO DAY/PETTY REPAIR TO MISC B/R ITEMS IN VARIOUS BLDGS AT OTM AND MD ACCN AT THANE UNDER GE (NW) MANKHURD

Amount

Demolition of brick work or stone/boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles complete all as specified and as directed

Demolition of cement concrete ,un-reinforced in ground floors and paving not exceeding 15 centimetre thickness, below or above ground level complete all as specified and as directed.

Demolition of cement concrete ,(reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar , in any internal dia and taking out of trenches if required complete all as specified and as directed.

Demolition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors , aprons etc

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MD land, complete all as specified and directed.

Labour for cleaning /cleaning of blockage of manholes, gully traps, floor traps, vertical soils/ waste pipe of different dia and sewage lines in the area of 31 WEU and NRS Thane under GE (NW) Mankhurd Note: a) The labour (02 nos) will report daily at 0845 hrs on all working days excluding Sunday and holidays at complaint cell centre and attend complaints till 1645 hrs given by Engr -In- Charge . Complaints needs to be cleared within 24 hrs after receiving the complaints . The contractor will deploy requisite labour and supply all T&P ( mechanical Iron rods, knot ropes , bamboo etc) scaffolding ladders any other materials required to clear the blockages at the site without any extra cost .Labour for cleaning of sludge from sewage lines (any dia) to manhole is included in quoted rates. In case any labour does not report to Engineer In Charge for the whole day or found missing more than half an hour on any day, Panel recovery @ RS.860/- per head per day shall be made proportionally from contractor's dues. b) The above item includes conveyance cost of labour with their tools to travel from pocket to pocket to attend complaints including removal of sludge from the site outside MOD land to a distance not exc 5km (The department shall not be liable to provide any kind/form of transportation to the labour). (c) Registers of labour attendance and complaints shall be maintained by contractor at their own cost,which shall be kept in the custody of MES Department(complaint cell) duly signed by contractor's representative ,JE(civil) and Engineer in charge.

Opening cover of septic tank, of size 5 - 15 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position all as directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

M&L in repair hume pipe septic tank for 10 user , designed to carry sewage and sludge water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc. dismantling and removing old Hume pipe connection complete all as specified and as directed.

Taking out old Brick bats and sludge etc. M&L for filled with brick bats of effective depth for soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete all as specified and as directed

M&L reinforced concrete pipes, class NP - 2, 300 mm bore, laid in trenches and jointed complete with collars Complete all as specified and directed.

M&L reinforced concrete pipes, class NP - 2, 150 mm bore, laid and jointed complete with collars Complete all as specified and directed.

M&L for 300 mm thick Concrete bed to drain pipes in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and as directed

M&L for 150 mm thick Concrete bed to drain pipes in cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and as directed

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and as directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed

M&L Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain complete all as specified and as directed.

All as per Serial Item No 17 herein above but PCC 1:2:4 Type B-1 using 20mm graded stone aggregate as in benching, coping including necessary form work complete all as specified and as directed

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 complete all as specified and as directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:6 mixed with WPC as per manufacturer's instruction and finished the surfaces even and smooth without using extra cement including taking down of old plaster complete all as specified and as directed (Note:- WPC will be measured and paid for separately.

M & L for rendering 15 mm thick in CM 1:6 on brick walls or concrete surfaces finished the surfaces even & smooth incl 1mm thick sagol finish including preparation of old surfaces in patches for repairs at any places inside the bldg complete all as specified and directed.(The work will be in carried out in patches as directed)

M & L for rendering 20 mm thick in CM 1:4 on brick walls or concrete surfaceslaid in two layers, Ist layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @ 2% by weight of cement content of finishing layer finished fair and even without using extra cement, including all necessary scaffolding/staging as required including preparation of old surfaces in patches for repairs at any places outside the bldg complete all as specified and directed.(The work will be in carried out in patches as directed)

Supply only integral water proofing compound as per latest IS specification complete all as specified.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) rough finished flat concrete surfaces

M&L fo fair finished flat form work to edges of concrete flats, treads, breaks infloors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work etc.

Cutting into existing manhole,150 mm bore pipe, for connecting new drains making good to pipe and removing cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates, smooth finish and re-forming benching complete all as specified and as directed

Cleaning manhole of size n.exc 1.50 Sqm by taking out sludge in semi liquid/solid stage (incl. all water etc) from inside of manhole of depth not exceeding 1.5 m and removing the sludge to a distance not exceeding 50m depositing in trenches including supply and sprinkling bleaching powder and covering sludge with earth to a thickness not less than 30 cm including all earth work, returning filling, removal of surplus soil & necessary temporary cleaning as directed by the Engineer-in-Charge.

All as per item 28 here-in-before but depth exceeding 1.5m but n.exc 3m deep.

Cleaning of SGSW/PVC pipe lines 100 mm to 150mm bore pipe and removing the blockage by means of rodding with and including bamboo splits/flexible iron wire or concrete malacces rods from manhole to manhole, through pipes from trap to manhole, rendering the system clear and flushing the delogged line with sufficient quantity of water and removing sludge/waste material etc. to a distance n. exc 50 M and burrying in pits and re-filling the same complete all as specified and directed by the Engr-in-Charge. (Note :- The cost for excavation and earth work for pits is deemed to be included in the unit rate).

S&F in repair 110mm bore PVC(SWR) bends any radius with access door complete all as directed

S&F in repair 110mm bore PVC(SWR) bends any radius complete all as directed

S &F PVC (SWR) bends, 75 mm bore, any radius

S&F in repair 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls

All as per item No.33 above, but 75mm bore

S&F 110mm bore PVC (SWR) branch piece single (Single Y ) equal or unequal

S &F PVC (SWR) branch piece,single(single Y) 75mm bore equal or unequal

S&F in repair GI tubing, medium grade, ISI marked conforming to IS -1239 including providing and fixing with all fittings and fixed to walls and ceilings or laid in floors complete including taking down old pipe of any location all as specified and as directed by the Engineer-in-charge for following sizes: Make: Tata, Swastik, Jindal, Prakash, Zenith, Surya (ISI marked) (a)15mm bore

(b) 20mm bore

M&L non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.16 Sqm, as in floors over screed bed or bedding layer of morar 15 mm in cement mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed. MAKE : SOMANY, ORIANT, JHONSON, RAK

M&L coloured glazed ceremic tiles of vertical portion of 300x200x7mm thick on vertical surfaces, skerting/dados etc. over screed bed or bedding layer of mortar 10 mm in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white / coloured cement. MAKE : SOMANY, ORIANT, JHONSON , RAK

M&L for coloured glazed ceramic tiles 300x200x6 to 7mm thick set and jointed in neat cement slurry and pointed with coloured cement as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

S&F in repairs Vitreous china wash down water closet pan “Pedestal Pattern” coloured with wc seat cover coloured closed pattern with flat bottom and mild steel chromium plated or aluminized hinging device including pvc flush pipe and joints etc and connection to drain, flushing, pipe, anti- syphonage pipe, and fixing arrangements with fixing bolts etc ,complete all as specified and directed

S&F in repairs Vitreous China squatting pan “Orissa ” pattern size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe ) including connecting to trap and to flushing pipe, etc including making good to dismantled portion of floors with P:C:C type B-0 complete all as specified and directed.

S & F in repairs Vitreous China Wash hand basin white, flat back, size 550x400 mm size (flat back or angle back type)excluding taps, waste, chain and plug and procelaim stopper but including cutting for and pinning ends of brackets or erecting stand.incl taking down pillar tap complete all as specified and directed

S&F in repairs hand shower (health Faucet) with 8mm dia 1 mtr Long flexible tube & wall hook complete all as specified .

S&F in repairs two way Bib cock long body with wall flange fitted by 15mm bore complete all as specified and as directed

Supply and fixing in repairs 10 litres capacity coloured PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets.

Supply only Plastic water closet seat cover white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device

Supply only CP brass waste fitting for wash hand basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed,32mm.complete all as specified and directed

Supply only 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&Fin repairs 15mm dia of fancy type chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repairs 15mm dia of chromium plated Angle valves, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for and fixed

S&F in repair PVC connection 15mm size with PTMT nuts of 600mm length

S&F in repair Soap dish, vitreous China white, approximate size 160x160x90mm

S&F in repair Brass chromium plated towel rail 20 mm dia 'D' type of 60 cm length between flanges

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

M&L for 100mm thick PCC 1:2:4, type -B-0, using 12.50mm graded stone aggregated as in sub base of sunkun floor and for any other propose in any location mixed with WPC @ 3% by weight of cement, complete all as specified and directed.

S&F in repair PVC floor trap 75mm dia out let including grating connecting jointing to waste pipe with lead jointing and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F cast iron covers and frame grade FG 150, suitable for sewage line manhole cover by making hole if required for members in each manhole and fixed with screws with nut and bolts and washers complete including locking arrangement complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation and paving etc complete all as specified & directed.

M & L Pre-cast cement concrete block masonry with solid blocks Type C1 1:3:6, exc. 10 cm in width and setting in Cement mortar (1:6) mortar, complete.

Ditto --- All as per item No 59 but except PCC blocks

M & l for plain Cement concrete Type B-1 1:2:4 (using 20 mm graded stone aggregate) as in surface channels and drains

M & L for plain Cement concrete Type D2 (1:4:8) (using 20 mm graded stone aggregate) as in surface channels and drains

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

M& L for preparation of new plaster surface of walls including necessary scaffolding and applying two coats of Anti Fungal acrylic exterior emulsion paint over a coat of primer (brand Apex Ultima manufactured by Asian or Equivalent manufactured by Berger as approved by GE) complete all as per manufacturers instructions

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion of concrete and making good disturbed in ground.

S & F in repair mild steel work as in posts or struts of fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, including all necessary drilling, bolting or riveting etc conforming to Fe- 290 Gde E-165 including dismantling of old posts with embeded portion, cleaning and surface preparation etc.

M & L for cement concrete 1:3:6 type C-1, using 20mm grade stone aggregate as in coping, bed blocks and the like including weathering slightly rounded or chamfered and throating as directed including necessary formwork complete all as specified and directed.

S & F Rolled Mild Steel Framed work as in doors or Gates of angle or other section confirming to Fe 410 - S, with gusset plates, rails braces, etc., complete, drilled for fixing of steel sheeting or other covering and hanging and fixing complete including dismantling of existing old framed work of any description

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0

M&L for PVC coated galvanised chain link fencing of wire mesh size 50 mm x 50 mm x 3 mm weighing not less than 2.18 kg/sqm (weight inclusive of PVC coat) and PVC coated line wire etc including fixing line wire to angle iron posts / rails straining bolts with provision of binding wire etc complete all as specified

S&F steel screws bolts (Machine made) made hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with one hexagonal or square nut , exc 5 cm but n exc 10 cm long dia of shank 5 to 10 mm complete all as specified and directed.

Supply and fix Round bars 10 mm dia for securing chain link fencing complete all as specified and directed.

S & F Camouflage painted concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, spring core wire (2.5 mm thick) of high with tape (0.52mm thick) and fixing the same over existing Y-shape angle iron tied with G.I.staple and G.I.clips to retain horizontal, including necessary bolts , all complete.

S & F in repair camouflage painted galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provn of galvanised mild steel wire, staple or steel pins etc complete all as specified and directed.

M&L Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:3:6 type C-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces including demolition of existing RCC cover complete all as specified and as directed

Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M & L for preparation of new steel surfaces of any description over 10 cm in width over girth not otherwise described over a one coat of pink primer over a two coats of synthetic enamel paint complete all as specified and directed

M&L 18-20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling at any description.

M&L Machine pressed precast concrete interlocking paver block Coloured any shape and size confirming to IS 15658-2006 of 60mm thickness, with grey cement and pigment M-35 Grade complete all as specified

M & L for sand cushioning for paver bocks complete including spreading ramming levelling and watering all as specified

M& L Pre Polished Chequered cement concrete tiles 30cm x 30 cm x 20-25 mm thick, set, jointed and pointed in near cement slurry in floors with mixture of grey white cement in equal proportions over screed bed or bedding layer of mortar 20 mm in cement mortar 1:6 complete all as specified and as directed.

Petty repairs to wooden joinery works such as Resecuring or easing and adjusting of doors, tower bolts, handles, windows kitchen cabinets in any size, refixing hinges etc by providing glue nails and screws to the satisfaction of user and rectifying other misc minor carpentary works assigned by the Engineer In charge. (Note : Replacement of builders hardware if required will be provided by the department .) Note item No 1 and 2 : (a) Rep of contractor will collect details of complint from departmant. The contractor will be alloted complaint on daily basis and sufficient resources will be deployed by him/her for completion of day to day comaplaint within 24 Hrs from the time of reporting. Any delay beyond above mentioned time limit suitable penalties as mentioned in relavant clause of Contract. (b) A detailed log of complaints with completion/ non-completion remarks from users/MES will be maintained by the contractor and same will be updated on daily basis in consulatation with Engr-in-Charge or JE detailed by him. (c) The contractor will make suitable arrangment for emergent complaints and will notify auth rep/Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond state time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard. (d) The quoted rated deems to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered CABS,NOFRA,TANAJI,NSB under GE(NW) Mankhurd. (e) The contractor will maintain suitable inventories and range of spares required to meet the complaints as same will be reviewed peridically by Engr-in-charge to streamline complaints disposal system.

All as per Item No 86 abouve but Petty repairs to plumbing/internal water supply works such as repair to leaking bib taps, pillar taps, mixers stop cocks by tightening and providing spindle,washer repairs to float valves, low leveled cistern to the satisfaction of user as assigned by the Engineer In Charge.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing own with water, etc complete all as specified and directed.

Supply only water proofing compound

M& L preparing new surfaces of walls applying two coat of oil bound distemper over one coat of primer complete all as specified & directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

S&F in repairs Stainless steel Friction hinges for Cupboard etc complete all as specified and as directed by the Engineer in charge.

S&F stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperature 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames) not exceeding 1.5 Sqm each complete as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames), exc 1.50 sqm but not exc 4.0 sqm each complete as directed

Taking down shutters of any description, exc 1 Sqm and n.exc 2 sqm each complete all as specified and directed

Taking down shutters of any description, exc 1 Sqm and n.exc 2 sqm each and refixing it in the same opening complete all as specified and directed

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fix New locking arrangement in place of old one and re-fixing the same shuters in existing position etc, complete all as specified and directed

Taking down carefully existing aluminium sliding window shutters,(glass/wire mesh) /frame exceeding 1.5 Square Metre and not exceeding 04 Square Metre each and re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully existing aluminium sliding window shutters, taking down of existing broken 5 mm thick plain sheet glass from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing 5 mm thick plain sheet glass with and including provision of new rubber gasket and re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully existing aluminium sliding window shutters, taking down of existing stainless steel wire mesh from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing stainless steel wire mesh of dia 0.36 mm and average width of aperture 1.40 mm with and including provision of "U" clip, re-fixing the shutters in existing position, complete all as specified and directed.

Taking down existing aluminium joinery of any description (frame/ shutters) with all fittings (but excluding grills) complete all as specified and directed.

M&L for IInd class Hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joint complete all as specified and directed.

S & F,IInd class hardwood 35mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and directed.

S&F for 35 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides and fitted to chowkhats complete all as specified and as directed.

S & F 2nd class hardwood, glazed and skelton shutter, 35mm thick, open rebated and prepared to receive glass, gauze etc, divided into square with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plane, chamfered or rounded, fitted with cut and mitered bead for securing glass, gauze etc, size of member of shutters as specified in SSR Part -I, section 8, class 8.24(a) (Door shutter), supplied and fitted to chowkats all as specified and directed.

S&F for Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F for Factory made solid PVC Moulded door shutter , 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm th. Moulded PVC sheet on the front face & 2mm plain coour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with wood free EPS etc, complete all as specified and as directed.

M&L Preparation of new or untreated painted wood and wooden based surfaces of any description not other wise described over 10 centimetre width or girth and applying Two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M & L for 20 to 25mm machine cut, polished Cuddapah stone slab, in single piece, in window cill, riser of steps, skirting, dado and pillar and similar work, laid over and including backing coat, in CM 1:4, 10 mm thick, jointed with grey cement slurry mixed with pigment to match the shade of the slab including taking down/dismantling old one complete all as specified and as directed

S&F standard aluminum section powder coated in partition / frame and door shutter, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco). Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

S&F in repairs aluminum anodised grill DG- 102 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

Supply only 4.80mm thick glass ordinary quality plain not exc 0.5 Sqm each pane with including wooden/rubber beading or gasket for aluminium section complete all as specified.

Supply 12 mm thick prelaminated particle, board, interior grade, prelaminated both sides with decorative choice laminations, fixed with screws to aluminium frame work complete all as specified.

M & L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

M & L for 12mm Plywood, grade BWP, type BB fixed with screws to timber frame work , fixed with screws to timber frame work including beadings etc, complete all as specified and as directed.

Supply only stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of aperture 1.40 mm , fixed in aluminium windows complete all as specified and directed.

S&F bands, straps supports or stay heavy for large gates, hook and pintle hinges clamps, hold fasts, wall tiles, hooks for hanging fans and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F 100 mm long stainless steel butt hinges fixed with stainless screw

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 250 mm.

S&F in repairs aluminium anodised 20mm dia Curtain rod complete

S&F in repairs aluminium anodised Curtain Brackets suitable to 20mm dia Curtain rod complete

M&L for providing cement concrete type C1, 1:3:6, using 20mm graded stone aggregate as in bed block for hold fast, coping etc including necessary form work complete all as specified and directed.

S/F in repairs brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type.

S&F in repairs wash hand basin, vitreous china white of size 550x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets,32mm waste fitting and waste pipe of 32 mm bore, brass, chromium plated for glazed ware wash basin and 15mm dia pillar taps chromium plated fancy type etc complete all as specified and directed.

S&F in repair low density polyethene pipes (LDPE) 32mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc.

S&F in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore complete all as specified and directed.

Dismantling water pipes (CI/PVC) (any size or pattern ) including all fittings, balance under credit ( measure overall as fixed along the centre line over fitting and accessories ) all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement, complete all as specified and directed.

M&L for PCC 1:2:4, type-B, using 20mm graded stone aggregated as in sub base of floors and for any other propose in any location mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: Supply only WPC will be measured and paid separately.

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

S & F in repairs Vitreous China urinals, half staff urinal, complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

Supply only chromium plated shower roses 125mm size with or without swivel joint including fixing to steel pipe or union etc.complete all as specified and directed.

Supply only soap dish complete all as specified and directed.

Supply only brass chromium plated towel rail 20mm dia 'D' type 600mm long between flanges, with and including chromium plated brass screws etc complete all as specified and directed.

Supply only Toilet paper holder complete all as specified and directed.

Supply only Health faucet with 1 mtr tube & hook complete all as specified and directed.

Supply only two way Bib cock long body with wall flange fitted by 15mm bore complete all as specified and as directed

Supply only CP corner glass with brass bracket screws etc complete all as specified and directed.

Supply and fix in repair 10 ltr, PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC etc, complete all as specified and directed.

S&F in repair for CP concealed stop cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply only CP angle cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply only CP bib tap 15mm bore fancy type with crutch or butterfly handle, screwed for iron pipe or for unions and fixed complete all as specified and directed.

Supply only brass Chromium plated wall mixer for mixing hot and cold water screwed down for iron pipe and fixed 15mm bore fancy type. Make -Jaqur,Prayag polymers Pvt Ltd or equivalent.

Supply only CP pillar taps 15mm bore cast copper alloy, chromium plated fancy type complete all as specified and directed.

Supply only 15 mm bore Stop valves, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed.

Supply only waste fitting of 40 mm bore brass , chromium plated for glazed ware for sink coulpling etc complete all as specified and directed..

Supply only waste pipe fittings for WHB/ sink 32mm bore fixed to wash hand basin/sinks coupling length pipe 0.90 mtrs each complete all as specified and directed..

Supply only 15mm size PVC connection with PTMT nuts 450mm length.complete all as specified and directed.

Supply only stainless steel grating in round shape 100mm dia complete all as specified and directed.

Supply only plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc complete all as specified and directed. Note : A sum of Rs. 28165.00 towards sch of credit shall be deducted to arrive the contract sum.

M/s Mukesh Engineers

Shree Ayyappa Engineering

M/S KHUSHI ENTERPRISES

Anjali Constructions

M/S VISHRANTA CONSTRUCTION

AM ENTERPRISES

cooltech engineering services

sahajanand const co.