GE (N) P/TOKEN- 02 OF 2021-2022 PROVISION OF CERTAIN LBW, RW AND SPECIAL REPAIR WORKS IN THE AREA OF AGE B/R (CENTRAL) UNDER GE (NORTH) PUNE

Amount

Excavation over areas not exc.1.5 metres deep and getting out in soft /loose soil complete all as specified and directed.

Excavation over areas exc.1.5 metres deep but not exc. 3.0 metres deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth for foundation, sewage line, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exc.1.5 m in depthfor foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in hard/ dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and as directed.

Excavation in post holes ( or similar holes) each n.exc. 0.50 Cum, getting out, returning, filling in and ramming earth or borken rubble mixed with earth around, in layers n.exc. 25 cm thick in hard/ dense soil complete all as specified and as directed.

Removing of excavated material (soil) to distance not exc.50metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Removing of excavated material (soil) to distance exceeding 50m and not exc. 100metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Removing of excavated material (soil) to distance exceeding 250m and not exc.500metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Removing of excavated material (soil) to distance exceeding 1.50 Km and not exc. 5 Km and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

M & L Loose filling with aggregates of gauge 80 to 150 mm of broken bricks in soakage pits, soakage wells complete all as directed.

Material and labour for hardcore broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2 (using 40 mm graded broken stone aggregate) as in foundations, filling, sub base and mass concrete etc. complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 (using 40 mm graded broken stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-1 (using 20 mm graded broken stone aggregate) as in surface channels, benching for manholes and drains complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-2 (using 40 mm graded broken stone aggregate) as in foundation, filling and mass concrete, floor of septic tanks complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in lintels upto 1.5m clear span, seismic and other similar bands, cills, plinth courses, roof kerbs or mud stops, parapets, coping, benching, coping, hold fast blocks, bed blocks/ bed plates, kerbs for interlocking tiles etc. including weathering, slightly rounded or chamfered angles and throating including necessary form work all as specified and as directed.

Material and labour for precast RCC (nominal mix ) (1:2:4) type B-1, (using 20mm graded broken stone aggregates) as in manhole covers, baffle wall including form work/ mould complete all as specified and as directed.

Material and labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns and mass concrete complete all as specified and as directed.

Material labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.50m span complete all as specified and as directed.

Material labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in columns, pillars, piers,posts and struts complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work with fly ash bricks, old size, in one brick thick honeycomb walling, built in cement mortar 1:4 complete all as specified and directed.

Material and labour for 40mm thick PCC (1:2:4) type B1 (using 20mm graded broken stone aggregates) as in DPC to horizontal or vertical including necessary form work complete all as specified and as directed.

Supply and fix for factory made 50 mm thick, 900mmX650mm manhole cover with additional frame for fixing, of precast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) finished the surface even and fare including reinforcement as per manufacturer's design and set in CM 1:4 and handles complete all as specified and as directed.

Material and labour for green marble 18 to 20mm thick (table rubbed and polished) as in skirting/ border/ jamb/cill/floor, laid with cement slurry over and including 10mm thick rendering in cement mortar (1:3), jointed with grey cement slurry mixed with pigment to match the shade of slab complete all as specified and as directed.

Material and labour for 18 to 20mm thick granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and like in cement mortar (1:4) over and including 10mm thick backing coat in cement mortar (1:3), pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting, edge moulding, full curving the edges complete all as specified and as directed.

Labour only for full round moulding to 18 to 20mm thick granite/ green marble slab complete all as directed.

Material and labour for formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any ) of foundation and plinth beam and similar works, vertical or batter etc for rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200 mm thick for fair finished flat, circular surfaces of concrete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves, bands, including supports, overhangs, etc. for fair finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, columns and stanchions, square, rectungular or polygonal for fair finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc.10cm but n.exc. 20cm wide for fair finished surfaces complete all as specified and as directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc. 5cm but n.exc. 10cm wide for fair finished surfaces complete all as specified and as directed.

Material and labour for 2nd class hard wood timber fixed, in scantlings, clean sawn unframed work including dismantling timber scantlings, unframed work, 40 sq. cm and over in section, in any position complete all as specified and as directed.

All as per Srl item No. 38 above but except timber.

M & L for 2nd class hard-wood clean sawn battens, cross sectional area exc. 5 Sqcm and not exc. 15 Sqcm, spaced at 30cm centres to centres fixed with nails complete all as specified and as directed. (NOTE : Measurements shall be taken overall including both battens and spaces. Deductions shall be made only for openings exceeding 0.4 sqm each).

Fixing only for 2nd class hard-wood clean sawn battens, any cross sectional area spaced at 30cm centres to centres fixed with nails complete all as specified and as directed. (NOTE : Measurements shall be taken overall including both battens and spaces. Deductions shall be made only for openings exceeding 0.4 sqm each).

M&L for Eaves/ weather boarding with 20mm thick fibre cement board (non asbestos) and fixed with self drilling and tapping screws of CSK head and joints finished with jointing compound and fiber tape as per manufacturer's recommendation complete of approved arch pattern any size and shape including taking down existing board complete all as specified and as directed. Make: V-Board (Visaka Industries Ltd)/ Everest/ Charminar/ Ramco/ Shera wall

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc.1.5 sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Taking down shutters of any description, area not exc.1 sqm each complete all as directed.

Taking down shutters of any description, area exc.1 sqm and not exc. 2 sqm each complete all as directed.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail, bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed.

Supply and fix for factory made solid Panel PVC door shutter, 30mm thick (style) consisiting of frame made out of MS tubes for top and bottom rails. M.S. frame shall covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail, bottom rail; panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90°) and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawing including fittings complete all as specified and as directed. Make: Rajshri/ Sintex/Duraplast/Accucell

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick wood grain printed PVC sheets and edges will be painted to match with printed sheet, reinforced with mild steel square tube complete all as specified and as directed. Make: Rajshri/ Sintex/Duraplast/Accucell

S & F Factory made fully glazed/wire gauge (single piece Both side) PVC prelam door shutter 29 to 30mm thick consisting of frame made up of MS tube of size 19mm X 19mm (19 guage) for top & bottom rail and in styles. Single piece plain coloured PVC sheets of 5mm thick to be used to cover style & rails. For edges, PVC sheets strip of 10mm thick struck inside with solvent cement. Plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert with PVC solid core board 19mm to 20mm thick. Panel shall be of wire gauge stainless steel wire cloth 0.36mm nominal dia of wire and everage width of aperture 1.40mm, stainless steel wire cloth shall be covered with aluminium XPM in rhombus shape in one piece from top to bottom rail, fixed with self tapping screw not less then 50mm long complete all as specified and directed by Engineer-in-Charge. Make: Rajshri/ Sintex/Duraplast/Accucell

Supply and fix for 150 mm long aluminium anodised, barrel tower bolts of extruded section, fixed with stainless steel screws (conforming to the sample kept in GE office) complete all as specified and as directed.

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, (conforming to the sample kept in GE office) complete all as specified and as directed.

Supply and fix for 250mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

S&F Stainless steel butt hinges 100mm medium weight all as specified and directed. NOTE :- All screws shall be self tapping chrome plated and length of screw not less 38 mm complete all as directed and specified.

Supply and fix for 100mm size mild steel butt hinges, heavy weight, cold rolled and fixed complete (conforming to the sample kept in GE office) all as specified and as directed.

Supply and fix for 100mm size mild steel butt hinges, medium weight, cold rolled and fixed complete (conforming to the sample kept in GE office) all as specified and as directed.

Supply and fix for 75mm size mild steel butt hinges, heavy weight, cold rolled and fixed complete (conforming to the sample kept in GE office) all as specified and as directed.

S&F stainless steel auto close/ hydraulic hinge suitable for shutter of not exc 0.50 sqm area complete all as specified and as directed. Make Prayag Cat No. 5120 or equivalent of makes as per Appx 'A' as approved by GE complete all as specified and as directed.

Supply and fix for 150mm size extruded aluminium alloy handles fabricated type anodised fixed with stainless steel screws complete (conforming to the sample kept in GE office) all as specified and as directed.

Supply and fix for magnetic catch, heavy duty and connecting plate to shutters and frame complete all as specified and as directed.

Supply and fix for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S & F Mild steel work for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. or securing with clips complete all as specified and as directed.

Material and labour for mild steel round bars 10mm dia. and over, as in rungs, steps, cut to length, bent to shape required, including hooking ends complete all as specified and as directed.

Material and labour for mild steel TMT bars, 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. or securing with clips complete all as specified and as directed.

Supply and fix for rolled mild steel section Fe 410-W(Gde-E-250) quality A as in main and cross beams, hip and jack rafters, purlins connected to common rafters and running rails and guides for sliding doors, column posts, wind ties, fixed with angle cleats or other connecting plates, drilled for fixing all as specified and directed.

Material and labour for rolled mild steel Fe 410-W(Gde-E-250) quality-A in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

Supply and fix for mild steel work in tubular trusses, main columns, posts, for structural work including special shaped washer etc. complete using hollow mild steel sections of square or rectangular tubes conforming to IS: 4923-1997 grade St.-240 fixed with angle cleats or other connecting plates complete all as specified and as directed.

M & L for aluminium anidised frame for partition wall, doors, windows, ventilators with one or more rebate including jointing cleats for fixing etc. complete all as specified and as directed.

Supply and fix for aluminium anodised powder coated louvered ventilator with provision of exhaust fan opening with adjustable louvers using ‘Jindal” aluminium section or equivalent make as specified including glass 3mm thick ordinary quality, frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed.

Supply and fix for aluminium anodised three track sliding window with two glazed shutters, one shutter with and including 4mm thick tinted glass of modiguard and one shutter with and including stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing, handle, locks, PVC rubber lining of transparent colour etc complete all as specified and as directed. Catalouge numbers of Jindal company or equivalent make sections : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

Supply and fix for aluminium anodised powder coated three track sliding window with two glazed shutters, one shutter with and including 4mm thick ordinary quality float glass and one shutter with and including stainless steel wire mesh 0.36 mm dia wire and 1.40mm aperture including good quality of bearing, handle, locks, PVC rubber lining of transparent colour etc. complete all as specified and as directed. Catalouge numbers of Jindal company or equivalent make sections : Three track bottom – 20957, Three track top/vertical – 20958,Handle – 20606, Interlocking – 20605, Top and bottom – 20604.

Supply and fix for aluminium powder coated partition using ‘Jindal’ aluminium SP/ DP section or equivalent make as specified with 5mm thick tinted glass, PVC rubber beading/12mm thick prelaminated particle board fixed with glazing clips etc./ both complete all as specified and as directed. Sections : SP (Single partition) - 20033, DP (Double partition) - 20034, Glazing clips - 4407

Supply and fix for fully glazed single/ double leaf openable door, using aluminium powder coated sections on door floor spring, pivots, with 4.5mm thick glass in panels fixed with aluminium glazing clips Jindal section No. 19381 and 19352 and PVC rubber beading all around including 1” interlock and handle, two lever door lock, sliding wheel complete all as specified and as directed. Jindal section Nos : Top-19528, Middle – 19575, Bottom – 19530, Vertical – 19526, 1” Interlock (20939), 1” Handle (20602)

Supply and fix for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

Supply and fix (Except sheeting) for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

Material and labour for 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 120gm/ Sqm complete all as specified and as directed.

All as per Srl item No. 79 above but except sheeting

Supply and fix in repairs 0.56mm thick plain, Aluminium sheeting, alloy 31000H4 in ridges, hips, valley gutter, crumple joint, drip and straight flashing (length and girth as fixed) complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Material and labour in repair for 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

Material and labour in repair for 6mm thick asbestos cement, two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts etc. complete all as specified and as directed.

Supply and fix for 6 to 8mm thick sandwitch type polycarbonate sheet fixed with necessary self driven screws on wooden/ masonry surfaces complete all as specified and as directed.

Material and labour for Roof tiles Mangalore pattern interlocking at side joints, laid dry including dismantling of tiles complete all as specified and as directed.

M&L for Roof tiles (Except tiles) Mangalore pattern interlocking at side joints, laid dry including dismantling of tiles complete all as specified and as directed. (Note : Serviceable tiles obtained from dismantled shall be re-used.)

Material and labour for ridge or hip tiles to suit Manglore pattern of roofing tiles, bedded and jointed in cement mortar (1:6) etc including dismantling of tiles complete all as specified and as directed.

Material and labour for 0.90mm thick decorative laminate type 1 of surface finish, colour, pattern and size as approved, fixed with approved adhesive as per manufacturer’s instructions on horizontal and vertical surfaces etc. complete all as specified and as directed.

Material and labour for 18mm thick plywood, grade BWR, type BB, number of ply 9 Nos, fixed with fevicol and nails for working table/ storage almirah, cabinets, cupboards, racks and wall panelling, to the size and pattern as directed including fixing on walls, floors etc.including taking down existing complete all as specified directed.

Material and labour for 12mm thick plywood, grade BWR, type BB, number of ply 7 Nos, fixed with fevicol and nails for working table/ storage almirah, cabinets, cupboards, racks and wall panelling to the size and pattern as directed including fixing on walls, floors etc. including taking down existing complete all as specified and as directed.

Supply and fix 18/19mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Material and labour for 12mm to 12.5mm thick mineral fibre board false ceiling on and including GI powder coated grid work of size 600 mm x 600 mm with using 32.5mm x 23.5mm x 1.5 mm thick main tee, 25 mm x 23.5 mm x 1.28 mm cross tee and 25mm x 23.5mm x 1.2mm angle fixed to wall for false ceiling including necessary supporting hanger with 3.0mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling, suspended @ 120 cm C/C both ways, size of grid shall be 605 mm x 605 mm complete all as specified and as directed. Make :- Armstrong, Diaken, New Age (ACE). Note: Height of ceiling is above 5 metres.

M & L machine cut cudappah stone slab 20-25mm thick as in lintels, shelves, vertical surface over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab or arldite including rubbing and polishing complete all as specified and as directed.

Material and labour 75mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection, floor, hardstanding, courtyard, path laid in alternate bays not exc. 3.0m, finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour 100mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in hardstanding, courtyard, path laid in alternate bays not exc. 3.0m, finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour 75mm thick PCC (1:4:8) type D2 (using 40mm graded broken stone aggregate) as in sub base complete all as specified and as directed.

Material and labour 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded broken stone aggregate) as in sub base floor finishing the surface even and fair complete all as specified and as directed.

Material and labour 40mm thick PCC (1:2:4) type B1 (using 20mm graded broken stone aggregate) as in floor topping finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles of minimum size 300mm x 200mm x 7mm thick as in vertical surface such as dado/ skirting and of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles of size 400/450mm x 300/350mm x 7mm thick as in vertical surface such as dado/ skirting and of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.06sq.m but not exceeding 0.11sq.m as in floor etc., colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), joint free, area of each tile exceeding 0.11sq.m but not exceeding 0.18sq.m as in floor etc., colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for coloured shade vitrified ceremic tiles 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm but not exc. 1.00 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and colour/shade/ pattern as approved by GE over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour for coloured, glazed ceramic tiles, of size 600mm x 300mm x 9 to 10mm thick as in vertical surface, shade/ pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured, non skid ceramic tiles, joint free, area of each tiles not exceeding 0.06Sqm x 7 to 8mm thick as in vertical surface, shade/ pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

Material and labour for machine pressed precast cement concrete coloured interlocking paver block, glossy rubber moulded, of triangular / Zigzag / Haxagone/any shape/design and size as approved, 60mm thick, conforming to IS 15658-2006, M-35 with grey cement and pigments grade in floor/ paths/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including filling the joints with sand complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample.

Material and labour for coloured glossy rubber moulded chequered cement concrete tiles of size 30cmx30cmx 25 to 27mm thick in floor, set, jointed and pointed in neat cement slurry with grey cement and pigment over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

Material and labour for rendering 10mm thick in cement mortar (1:6) on fair faces of brick or concrete surfaces finished fair and even all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces and provn of sagol finish complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces wall finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar on fair faces of brick or concrete surfaces in two layers i.e. Ist layer of 10 mm thick rendering in cement mortar (1:4 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ), second layer mixed with integral water proofing compound as per manufacturer's instructions with second layer, finished even and smooth without using extra cement complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of concrete roof surfaces, mixed with integral water proofing compound @ 3% by weight of cement, finished even and smooth without using extra cement complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces, mixed with integral water proofing compound as per manufacturer's instructions, finished even and smooth without using extra cement with spong finish complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

M&L for raised plastering 20mm thick in cement mortar 1:3 designed with grooves over sloped roof slab mixed with integral water proofing compound as per manufacturer's instructions complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

M & L for Brick Finish Texture having Total Thickness of 2 mm with stamping, colour as approved complete all as specified below and as per manufacturer's instructions:- 1. First coat of COARSE Material (Base Coat - Groove Colour) applied by steel trowel with thickness of 1mm. 2. Second Coat of FINE material (Top coat- pigmented) applied by trowel thickness of 1 mm 3.Third Coat of Protective Water repellant coat clear lacquer coat by Roller. The work shall be carried out up to all heights & all floor levels and as per the directions of the Engr- In- charge. Make: Instakrete Coatings LLP, Pune or equivalent as approved by GE.

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Material and labour for appying one coat of alkali resistant primer on walls/ ceiling complete all as specified and as directed.

Material and labour for applying 1 to 1.5mm thick white cementitious wall care putty on wall/ceiling, filling cracks by crack filler and smoothen surface with sand paper complete all as specified and as directed.

Material and labour for preparation of newly plastered or unplastered surfaces of wall and applying three coats of white wash all as specified and as directed.

Material and labour for preparation of newly plastered or unplastered wall surfaces and applying two coats of oil bound/ acrylic distemper over a coat of alkali resistant priming paint complete all as specified and as directed.

Material and labour for preparation of newly plastered or unplastered wall surfaces and applying two coats of oil bound/ acrylic distemper over a coat of priming paint over a coat of putty to obtain true line to achieve smooth surface complete all as specified and as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic distemper over a coat of primer complete all as specified and as directed

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of acrylic distemper complete all as specified and as directed

Preparation of old treated plastered surface of wall by filling cracks by crack fill paste of Berger or of equivalent make as approved by GE, removing loose paints etc , removing nails etc and making good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

All as per Srl item No. 128 above but two coats of acrcylic distemper

Preparation of old treated plastered surface of ceiling by filling cracks by crack fill paste of Berger or of equivalent make as approved by GE, removing loose paints etc , removing nails etc and making good surface by applying white birla/JK wall putty wherever required, smoothen surface by sand paper and applying one coat of acrcylic distemper complete all as specified and as directed.

M&L for one subsequent coat of acrcylic distemper on ceiling surfaces complete all as specified and as directed.

M&L for complete removal of exisiting finish of exterior paint using steel wire brush, sanding machine, rubbing ivory paper etc and washing , rubbing down, pointing in CM (1:3) if any damaged portion found in the arches on stone masonery upto the height of 10 meters in heritage buildings. The arch on stone masonery shall be finished with brick finishes by applying two coats of exterior apex paint of approved tint in asian paint or equivalent as approved by Engineer-in-charge. The span of arches is 2.5m to 3.00 meter with a rise of 1.5meter in arch, making brick pattern finish using white exterior apex paint to provide a heritage look to the arch masonery complete all as specified and directed. Note :- Rates are deemed to be included for scaffoldings, safety measures required for working on or upto the height of 15 meters vertical or steep slopes.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer complete all as specified and as directed

Material and labour for preparation of old treated plastered or unplastered surfaces of walls and applying one coat of cement base paint complete all as specified and as directed

Supply and fix 5.50mm thick tinted sheet glass, ordinary quality in square, rectangle any size and glazing with and including suitable size rubber beading/ stainless steel pins etc. as in aluminium frames/ shutters complete all as specified and as directed.

Material and labour for preparation of new untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old surfaces of wood and wood based material surface of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and as directed.

Material and labour for preparation of battens, any size and spacing and treated all over (measured overall on one side only, spaces not deducted) with two coats of creosote oil complete all as specified and as directed.

Material and labour for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for one coat using Dr. Fixit Pidicrete URP with one part URP mixed with 1.5 part cement complete all as manufacturer's instruction and as directed

Supply and fix 15mm bore steel water tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fix 20mm bore steel water tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing with all fittings and connections complete all as specified and as directed.

Supply and fix for 500 litres capacity, rotational moulded polythelene water storage tanks (ISI marked) (cylindrical vertical with closed top), hoisted and fixed in postion complete all as specified and as directed.

Supply and fix for 1000 litres capacity, rotational moulded polythelene water storage tanks (ISI marked) (three layer, cylindrical vertical with closed top), hoisted and fixed in postion including 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) including dismantling existing tank complete all as specified and as directed.

Supply and fix bib tap for 15mm bore pipe, chromium plated, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fix stop valves for 15mm bore pipe, with wall flange, fancy type, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fix for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 15mm bore, ISI marked complete all as specified and as directed.

Supply and fix for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 20mm bore, ISI marked complete all as specified and as directed.

Supply and fix for 20mm bore ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and as directed.

Supply and fix Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and as drected.

Supply and fix for 15mm size PVC connection 450mm long including PTMT nuts etc complete all as specified and as directed

Supply and fix for stack clamps made out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm bore pipe complete all as specified and as directed.

Supply and fix for PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

Supply and fix for PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fix for PVC (SWR) pipe 75mm bore single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

Supply and fix for PVC (SWR) bends any radius of 110mm bore with access door complete all as specified and as directed.

Supply and fix for PVC (SWR) bends any radius of 75mm bore with access door complete all as specified and as directed.

Supply and fix for PVC (SWR) branch piece, single Y, equal or unequal with access door for 75mm bore pipe complete all as specified and as directed.

Supply and fix for PVC (SWR) junction single (single 'T') equal or unequal for 110 mm bore pipes with access door complete all as specified and as directed.

Supply and fix for PVC (SWR) vent cowl for 110 mm bore pipe complete all as specified and as directed.

Supply and fix for PVC (SWR) floor/ nahani trap 75 mm dia of outlet, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

Material and labour for PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D2 ( using 40mm graded broken stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore of pipe all as specified and as directed.

Material and labour for 150mm bore RCC pipes, class NP2 laid and jointed with collars and tested complete all as specified and as directed.

Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in PCC (1:2:4) type B-1, smooth finished and reforming benching as required for 150 mm internal dia of pipe complete all as specified and as directed.

Supply and fix for vitreous china, squatting pan, 'Orissa' pattern, complete of size 580 mm x 440 mm, white, with CI 'P' of 'S' trap, front or back inlet and foot rests any pattern, including provision of lime concrete and connections for inlet, outlet, anti-syphonage pipes, etc. complete all as specified and as directed.

Supply and fix in repair for vitreous china, squatting pan, 'Orissa' pattern, complete of size 580 mm x 440 mm, white, with 100mm bore CI 'P' trap long arm of length upto 700mm as per site requiremen, front or back inlet and foot rests any pattern and PVC high level flushing cistern 10 litres capacity, valveless, syphonic action type, white with inlet, ball valve, float and handle including brackets including 32mm dia PVC flush pipe and all necessary fittings, connections for inlet, outlet, anti-syphonage pipes, etc. including making good to floor complete all as specified and as directed.

Supply and fix for vitreous china European type wash down water closet pan, (Pedestal pattern), white including plastic water closet white closed pattern with flat bottom and cover with mild steel chromium plated hinging device and fixing bolts, necessary inlet and outlet connections complete all as specified and as directed.

Supply and fix 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, 32mm dia PVC flush pipe and connections to pipes, making good the disturbed surfaces complete all as specified and as directed.

Supply and fix in repair vitreous China half stall type urinal , white, including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, including 5 ltrs capacity PVC automatic flushing cistern with brackets, 32mm dia PVC flush pipe and discharge pipe, grating and union for discharge pipe complete all as specified and as directed.

Supply and fix vitreous China urinal full stall type, white, including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement paste, grating and union for discharge pipe complete all as specified and as directed.

Supply and fix for vitreous chinaware wash hand basin with pedestal, white, flat back, size 550x400 mm including pedestal, pillar tap, fancy type , cast copper alloy, with capstan heads, chromium plated, cast copper alloy, screwed down high pressure, with or without lettered 'Hot' or 'Cold' and fly nuts screwed for iron pipe for 15mm bore, CP waste coupling, chain and plug, waste fittings, union and PVC waste pipe 32 mm dia of required length and all necessary inlet outlet connections including CI brackets complete all as specified and as directed.

Supply and fix in repair for vitreous chinaware wash hand basin, white, flat back, size 550x400 mm including 32mm dia. chromium plated, CP waste coupling, chain and plug, waste fittings, union and PVC waste pipe 32 mm dia of 90cm long, CI brackets and all necessary inlet outlet connections complete all as specified and as directed.

Supply and fix in repair for 5mm thick float glass looking mirror of size 450mm x 500mm with 6mm thick ply wood back and aluminium powder coated frame complete all as specified and as directed.

Supply and fix, laying and jointing for UPVC pipes (SCH-40) 150mm bore including necessary fittings such as bends, elbows, tees, unions, reducers, clamps, jointing materials etc laid in trenches complete all as specified and as directed.

Demolition of brick work/ precast concrete block walling/ boulder masonary, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

Dismantling of stone slabs, chequered tiles, interlocking tiles of any description or thickness in floor, apron etc., laid bedded and pointed in any mortar complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as directed.

Dismantling battens for tiles, shingles etc. of any size including tiling fillets spaced exceeding 15cm complete all as directed.

Dismantling structural steel work including doors, gates including framed truss etc. complete all as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness sheets including Nainital or similar pattern roof coverings/ galvalume/ aluminium sheeting complete all as directed.

Dismantling of wall/ceiling board/POP ceiling of any description and any thickness including cover fillets/ grid etc complete all as directed.

Supply, laying and testing for LT XLPE UG cable insulated screened PVC bedded galvanised steel strip or wire armoured, heavy duty electric power cables with stranded aluminium conductor 1100 volts grade with cable glands, lugs etc laid in trenches, fixed on wall/ pole including brass cable glands, clamps etc. of size 10 Sqmm 2 core cable complete all as specified and as directed. Note: Excavation and earth work, sand cushioning, brick protection, GI pipe shall be measured and paid separately.

All as per serial item No.188 here-in-before but for 06Sqmm 4 core cable.

Taking down carefully unserviceable point wiring of any description/ type/ size of light/ fan / tube/ power / two way/ bell etc. on TW batten/ conduit/casing caping including removal of batten/ conduit/ casing caping/ gutties/ wooden boards/ switches/ sockets/ regulators/ holders/ ceiling roses/ call bells/ light fittings etc. for taking credit and making good the disturbed surfaces of wall/ ceiling so as to match with the existing finishes complete all as directed. Note: Taking down of seviceable fittings and fixtures shall be measured and paid separatey.

Taking down the existing unserviceable main switch/ cut out/ MCB DBs/ sheet metal enclosure of any type/ capacity/ description as existing at site including MCBs any type/ capacity and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Taking down the existing unserviceable tube light, decorative wall mounted, bulk head, batten aluminium,street light fitting, down lighter any type/ capacity and refixing the same and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLSH copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded cable 1100 volts grade ISI-694 marked through and including heavy duty ISI marked, 20 mm dia rigid PVC conduit of white/ ivory/black colour on pressure patti with welding on channel including all accessories in wall/ ceiling/ chanel etc, with GI terminal sunken boxes 1.2mm thick 60mm deep of suitable size as per site requirement, covered with modular white cover plate with frame suitable for housing modular switches, sockets, regulators etc. including PVC insulated multistranded FRLSH copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor and connecting to the common earth dolly for one light point controlled by one, one way switch 5/6 Amps complete all as specified and as directed.

All as per serial item No.193 here-in-before but point wiring for one exhaust fan/ wall fan point controlled by one, one way switch 5/6 Amps and regulator.

All as per serial item No.193 here-in-before but point wiring for one 3 pin 5/6 Amps socket outlet controlled by one switch on same board.

All as per serial item No.193 here-in-before but point wiring for one 3 pin 5/6 Amps socket outlet controlled by one switch on independent board.

All as per serial item No.193 here-in-before but with FRLS copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded cable 1100 Volt grade ISI-694 marked including PVC insulated multistranded FRLSH copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor for 3 pin 15/16 Amps socket outlet on independent board.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLS copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded flexible bright annealed cable 1100 volts grade ISI-694 marked through and including heavy duty ISI marked, PVC casing caping including all accessories fixed to walls/ ceilings etc., with concealed terminal sunken boxes factory made 16 SWG thick pressed steel of suitable size as per site requirement, covered with modular white cover plate with inner frame suitable for housing modular switches, sockets, regulators etc. including PVC insulated multistranded FRLS copper conductor 1.5 Sqmm (nominal area) single core flexible cable as earth continuity conductor and connecting to metal bodies of luminaires/ fans etc. for one light point controlled by one, one way switch 5/6 Amps complete all as specified and as directed.

All as per serial item No.198 here-in-before but point wiring for one 3 pin 5/6 Amps socket outlet controlled by one switch on independent board.

All as per serial item No.198 here-in-before but point wiring for one bell/ buzzer point controlled by one bell switch 5/6 Amps.

All as per serial item No.198 here-in-before but point wiring for one 3 pin 5/6 Amprs socket outlet controlled by one switch on same board.

All as per serial item No.198 here-in-before but with FRLS copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded cable 1100 Volt grade ISI-694 marked including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor for 3 pin 15/16 Amps socket outlet on independent board.

Supply and fix for lamp holder, PVC body/ polycarbonate type with back plate, brass terminals suitable for batten/ slanting fittings complete all as specified and as directed.

Supply and fix for modular switch, one way 5/6 Amps, 1 module complete all as specified and as directed.

Supply and fix for modular switch, one way, 15/16 Amprs, 1 module complete all as specified and as directed.

Supply and fix for modular bell push, 6Amps, 1 module complete all as specified and as directed.

Suply and fix for bell electric multi music type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

Supply and fix for modular socket outlet multi purpose 2 & 3 pin 5/6 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular socket outlet multipurpose, 3 pin 5/6 Amps and 3 pin 15/16 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular step type electronic fan regulator flush type 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Supply and fix for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed.

Supply and fix for MCB SPN rated capacity 40 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB SP rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB SPN rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for ceiling rose, 3 terminals, PVC/ polycarbonate type, isolated body including PVC box 3" round type complete all as specified and as directed.

S & F highly efficient LED retrofit Lamp 9W used as a ready replacement for existing GLS/CFL of make C&S Cat part no CHANDRA/9W/W or equivalent in BajaJ/Havells/ Crompton all as specified and as directed.

Supply and fix for LED 10 watts batten aluminium extruded with decorative end caps all as per Cat No. BCLSB 10 NW/ WH of make Bajaj, Wipro Cat No. LL20-111-XXX-65-NE, Jaquar Cat No. LGLZ01X010XC or its equivallent model in Havells, Philips as approved complete all as specified and as directed.

Supply and fix for wall mounted LED 18 watts with lumens out put not less than 1800 lumens, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired all as per Cat No. BLRB-DB118 & BLRB 18W CWc of make Bajaj or equvalent of make Philips/ Wipro/ Havells/ Syska/ Jaguar (Cat No. LGLZ01X020XC) as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 18 watts complete all as specified and as directed.

Supply and fix for wall mounted LED 20watts with lumens out put not less than 2000 lumens, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired all as per Cat No. BCLAB 20W of make Bajaj, Cat No. LL20-281-XXX065-ALI of Wipro or equvalent of make Philips/ Havells/ Syska/ Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 20watts complete all as specified and as directed.

S&F ceiling fan (after assembling the same) with fan hook/box, 1200mm sweep BEE 5 star rated, 3 blade ISI marked, white colour, 240 volt AC 50 HZ single phase with hanging rod, conopy set, clamps, bolts nuts and connecting with three core flexible PVC copper conductor cable of size 0.50 sqmm from ceiling rose to fan complete all as specified and directed. Make: Havells Cat No. ES-50 or Bajaj Model No. Kessals 50/ Electra 50 or equivalent of Usha, Orient Electric, Crompton.

Taking down carefully ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same after cleaning dust, oiling, greasing, servicing etc. with replacement of unserviceable PVC insulated PVC sheathed 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal, complete all as specified and directed.

Supply and laying 40mm outer/ 32mm inner dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS- 14930 Pt-II with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less then 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel and connected to main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways with one handle for lifting made out of 8mm dia MS bar, funnel, wire mesh, 20 mm bore galvanized steel tubing (medium grade) for watering, filling charcoal or coke and salt in alternate layers, 15mm bore galvanized steel tubing light grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No.3 of SSR Part-I. (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in quoted rate)

Material and labour for sub main wiring with approved colour coding as per IS with two runs of single core PVC insulated FRLSH cable with multistranded copper conductor of size 4.0 Sq. mm nominal area and drawing through and including non metallic rigid heavy duty PVC conduit and conduit accessories concealed in wall including one run of single core PVC insulated 4.0 Sqmm (nominal area) multistranded FRLSH copper conductor as earth wire connected from DB to DB/ main board complete all as specified and as directed. (Note- Two runs of 4.0 Sqmm, one run of 4.0 Sqmm conductor and one run of PVC conduit will be measured as one unit)

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

L.T Associate

THE SAIRAM CONSTRUCTIONS