SPL REPAIR TO OR TOILET NEAR BLDG No. P-22 AND ADDITION/ALTRERATION TO BLDG No. T-88 INCLUDING PARTITION INSIDE THE ROOM, AT TPT COY ASC TYPE B UNDER GE (W) PATHANKOT

Amount

Sch 'A' Part-I B/R work:- Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, wall, arches, pillars, man-holes, drain etc complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) in ground floors and Paving not exc 15 cm thick (below or above ground level ) and removing the debris outside from defence land complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

S&F pressed steel frames 105 x 60 x1.25 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate including one shop coat of primer and back filling of hollow portion of frame including fixing of hold fast with plain cement concrete type B-0, 1:2:4 using 12.5 mm graded crushed stone aggregate complete all as spd and directed

M&L for brick work with sub class ‘B’ brick (old size), straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed..

All as per srl item No.8 here-in-before but except brick retrived from demolition

M&L for brick work with sub class ‘B’ brick (old size), straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed..

M&L for Brickwork withwith sub class ‘B’ brick, straight or curved to plan in any radius in half brick wall built in cement mortar 1:4 complet all as specified

S&F factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast, including plain/figured glass 3mm thick and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples`etc complete all as per details shown in drawing No CEPZ/C-TD/032/13 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 300mm long Aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminum alloy and fixed complete all as specified and directed.

S&F 150mm long aluminum, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 125mm long extruded aluminium alloy handles, cast type, anodised

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete including welding to steel frames as required at site complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified .

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S&F 15mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick horizontal or sloping for rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

M&L for 18-20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and as directed.

S&F in repair for 15mm bore Stop valves, fancy type, chromium plated with long shank and cup (concealed type),cast copper alloy, screwed down, high pressure, with crutch or above butterfly handle, screwed both ends for iron pipe or for unions and fixed (ISI marked) complete all as specified and directed.

S&F in repair 15 mm bore long body brass CP Bib taps cast copper alloy fancy type with capstan heads (chromium plated),and cup screwed down , high pressure for iron pipe complete all as specified and directed.

S&F in repair 15mm bore dia fancy type, chromium plated angular valves /stop valves, long shank, cast copper alloy, screwed down, high pressure ,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (ISI marked) complete all as specified and directed.

S & F in repair brass chromium plated shower roses 125mm size with or without swivel joints including fixing to steel pipe or union complete all as specified and directed by Engr-in-charge.

S&F in repair Stainless Steel Soap Dish or Soap Holder Dish for Bathroom with fixing arrangement complete all as specified and as directed.

S&F in repair for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe),Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete, including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F in repair CP brass towel ring 20mm dia, fancy type, superior quality, including CP screws and wooden/plastic cleats complete all as specified and as directed.

S&F in repair for 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repairs Vitreous china wash basin, counter sunk of size 550 x 400 mm, including cutting RCC slab counter and engraved the basin including 32 mm bore CP waste coupling long screw thread and 32 mm dia flexible waste pipe incl fixing of taps all as spd and directed.

S&F in repair for for Vitreous China wash basin, white or in matching colour of tiles, flat back, size 630x450mm including brackets, CP brass waste fitting 32 mm dia,PVC waste pipe 750 mm long( Minimum) cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repair for 15mm dia PVC connections 450mm long with PTMT nuts complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over screed bed or bedding layer 20 mm thick in cement mortar 1:4, complete all as specified and as directed.Note :- Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine & size of kota stone shall not be less than 550 mmx550mm .

M&L for machine kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over backing coat 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed. Note :- Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine & size of kota stone shall not be less than 550 mmx550mm .

M&L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over ,15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over ,15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in vertical/dado surfaceetc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over ,10mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for Glazed ceramic Coloured tiles in vertical/dado surface 450mmx300mmx7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over ,10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and directed.

M&L for colored (red/yellow) Machine pressed precast concrete interlocking paver block rubber moulded any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coting having high glossy finish confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey Cement and no pigment including 50mm thick sand cushioning bed complete all as secified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in copings, kneelers, apex stones,bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for 75mm thick plain Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in sub-base to floor finish and complete all as specified.

M&L for 5 mm thick rendering on brick work or concrete surfaces in CM 1:3 as in ceiling of roof slab ,fin, facia, culvert, chajjas, parapet and similar article etc finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in CM 1:6 on other than fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM 1:6 on other than fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) including and mixed with liquid water proofing compound @200ml/bag, on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick plain Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection,and paving 75 mm thicklaid in sloe finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ration 1:2 by weight and complete all as specified.

M&L for preparation of newly plastered surfaces of wall and applying one coat of chalk whitening as primer and applying two coat of oil bound distemper complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Taking down existing roof treatment of any description incl mud phuksha or PCC pedding if any (any no of layers) incl brick tiles , terracing tiles if any including removal to dabries in low laying area exc 1.00 KM but n exc 2.00 KM complete all as directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs or mub stop/ leveling course on existing roof or sunken floor of toilet portion, rounded and chamfered on edges, complete all as spd and directed.

M&L for 20mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth with WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in per bag of cement.

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface @0.30 ltr/Sqm manufactured by the same agency as that of APP by forced application with 10cm side laps and 15 cm end laps complete all as specified

S&F PVC (SWR) pipes 100 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors/walls complete all as spd and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors/walls complete all as spd and directed.

S&F PVC (SWR) bends ISI marked any radius 110mm dia complete all as spd and directed.

S&F in repair 75 mm bore PVC(SWR) floor traps plain with grating and 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.

Dismantling timber scantlings 40sqcm and over in section, in any position as in wooden trusses in framed work of any description complete all as specified and directed..

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying one coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings or PVC sheet in roof including ridges, sunshades or any position etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in sunshades ,roof covering, cladding to wall etc fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall and as in ridge etc fixed with self-tapping screws complete all as specified and directed.

S&F factory made 35mm thick of 2nd class hard wood Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain ,chamfered or rounded. fitted with cut and mitered beads for securing glass ,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, kiln seasoned, chemically pressure treated complete all as specified and directed.

S&F Factory made 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, 2nd class HW rail and style complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F in repair 25mm outer dia stainless steel bright finished ,fancy type decorative drapery rod of thickness 20 gauge with ends caps in (pair) fixed to wall with screws ,PVC gully including all necessary fixing arrangement including taking down old curtain rod complete all as specified and directed.

S&F in repair 15mm bore dia wash hand basin Brass central hole CP mixer for mixing hot & cold water screwed down for iron pipe complete all as specified and directed.

S&F in repair glass corner shelf quarter round with CP brass bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S&F in repair for gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and as directed.

S&F suspended false ceiling system using chicago metallic (E grid) exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 9.5mm thick gypsum tiles (600mmx600mm) laminated with PVC film on the face side and metalised polyester film on the back side with all four edges sealed with PVC film to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) complete all as specified and directed.

S&F in repair Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. Make Jaquar CAT NO Health Faucet SKU ALD-573 or equivalent in any of the make metnioned in list of product.

Sch 'A' Part-I E/M Portion:- Taking down old unserviceable copper/aluminium point wiring (light, fan, socket , power socket and bulk head fittings) on surface wiring on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators and sockets by unscrewing carefully from boards etc and making good disturbed surfaces of walls, as per existing finishes complete all as spd and directed.

M&L for point wiring for one light/one fan controlled by one switch with 1.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H 1100 volte grade cable, with and including PVC rigid concealed conduit (ISI marked) with all fittings including sheet steel/CI terminal box of adequate size including 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly, complete all as specified and directed. Note:- 1. connection of cable with MCBs/switch sockets shall be done through proper size copper /brass thimbles. 2. Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible. 3. Proper colour coud will be used for wiring as per the electrical rule and as directed.

All as per Srl item No 84 here-in-before but for 5 pin 5 amps socket outlet on the independent board controlled by one switch SP, one way 5 Amp, 240 Volts. complete all as specified and directed.

All as per Srl item No 84 here-in-before but for 5 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed.

M&L for point wiring with 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable with in and including PVC concealed conduit heavy duty with all fittings including anodise pressed steel sunken box with bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS-H cable as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface finishing the surface to match with the existingsurface complete all as specified and directed.

S&F switch piano flush type one way 5 amps SP 240 volts complete all as specified and directed.

S&F switch piano flush type one way 15 amps SP 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volts complete all as specified and directed.

S&F socket outlet 2 in 1, 5 pin, 5 and 15 amps flush type 230 volts complete all as specified and directed.

S&F lamp holder/batton holder/angle holder insulated body with bakelite back plate suitable for fittings complete all as specified and directed.

S&F ceiling rose 65 x 50mm three terminals complete all as specified and directed.

S&F ceiling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

S&F in replacement CFLs with LED Lamp, B22 type ,12 watt,complete all as specified and directed.

S&F in replacement energy saving decorative LED box type 20 W, 6500K, cool white, Lumen efficiency 110 lumen/watt, light fitting PVC housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories prewired and making connections with twisted flexible copper cable of suitable size from ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge.

Taking down carefully ceiling fan from the hook including dismantling the blades and minor repair such as replacement of locking pin, reel insulators, bolts, nuts etc and painting one coat of synthetic enamel paint of existing colour including rehanging the same at existing position after cleaning, greasing and connecting up with PVC insulated copper flexible wire of suitable size from ceiling rose to connector of fan complete all as specified and directed by Engr-in-Charge .

M&L for providing/ cutting the round/ square hole of required size in wall finishing the distrubed surfaces as per existing finishes complete all as spd and S&Fing MS ventilating fans Single phase, 230 volts 300 mm or 12” H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side (outer surface of the wall) and connecting with and including PVC insulated copper cable suitable size from ceiling rose to exhaust fan motor and writting MES No. with black synthetic enamel paint 2.0 cm high complete all as spd and directed by Engr-in-charge.

S&F in repair sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair MCB SP 240 volts any rating from 6 to 40 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in repair MCB SPN 240 volts any rating from 6 to 40 amps, 'B' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F energy saving , surface mounted, bulk head luminaire 10 watt with PDC aluminium housing and polycorbonate diffuser with IP 66 protection complete including connecting up with three core twisted flexible suitable size copper conductor cable complete all as specified and directed by Engr-in-Charge.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS-H flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS-H flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S&F in repair bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length not less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

M&L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 05 of SSR -2009 Part I and connecting to existing earth test point complete all as specified and directed or including testing on completion.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Supply, laying and testing in replacement LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sq. mm 2 core complete all as specified

Supply, laying and testing in replacement LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 16 sq. mm 2 core complete all as specified

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth and getting out in soft/loose soil for laying of cable ,pole foundation,stay,laying of pipe etc complete all as specified and directed.

Returning filling in, including spreading ,leveling ,watering and well ramming in layers not exc 25 cm complete all as specified.

Removing excavated soil to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for sand cushioning to under ground cables with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable complete all as specified (Note:-Punned thickness shall be measured and paid)

M&L for brick covering equal to length of bricks as mechanical protection to cable with well burnet sub class ‘B’ bricks laid as directed by the Engr-in-Charge.

S&F GI tubing light grade 50 mm bore for cable protection laid in trenches in road crossing or fixed to wall/Pole including fittings /clamp complete all as specified and directed.

M&L for galvanised steel tubing medium grade,20 mm bore with all fittings and fixed complete to walls and ceiling or laid in floor all as specified

S&F gun metal gate valve with iron wheel head, screwed both ends for iron pipes of 20 mm bore all as specified and as directed.

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 37,091.00 and any other reduction if any from quoted amount.

OMKAR SHARMA AND CO (BID ID -3489603)

BALKRISHAN GUPTA AND SONS (BID ID -3484173)

HARI OM ENTERPRISES (BID ID -3480788)