SPECIAL REPAIR TO BLDG NO P 26 OR MD ACCN P 44 OTM ACCN AT RLT AND PROVN OF TILING BLDG NO P 32 PATHWAY WITH CHEQURED TILES AND CERTAIN MINOR WORKS AT AKHNOOR UNDER GE NORTH AKHNOOR

Amount

LOCATION : FSD AREA AKHNOOR (i) Determining of SBC by manual boaring 100mm dia bore hole up to 6 mtr depth and performing SPT as per IS-2131 of 1996 collection of disturbed/undisturb soil sample take for test. In test case of gravely strata as refusal the open pit of 2 mtr depth if bldg work as directed by Engr-in-Charge and submission test report in triplicate. (ii) Conducting of necessary as test per relevant IS-Code/NBC 2005/SP-36 on all collected samples including the following: (a) Atterberg limits (Liquid limit, Plastic Limit and shrinkage limits) (b) Natural moisture content (c) Wet and dry density of soil. (d) Soil partical size distribution. (e) Triaxial shear test. (f) Shrikage test. (g) Consolidation test. (h) Specific grevity test for sand and rock. (j) Crushing strength test. (k) Premeability test. (l) Chemical analysis of ground water sample. (m) Free soil index. (n) Chemical analysis of soil. (iii) Submission of report of soil investigation along with photograph in pentuplicate duly annotated

(iv) Submittion of soil investigation report shall be with recommendation of type of foundation and SBC of soil at a suitable depth from AGL. SBC of soil at a depth of 1500mm & 2000mm shall also be workout for each bore hole. Water table if encountered during excavation shall also be reported for each bore hole along with soil profile.Expensive soil if encountered during excavation shall also be specified. Nos of holes for SBC = 16 Nos 6 mtr depth of each i.e.total 16x06 = 96 RM

LOCATION : SUNDERBANI (i) Determining of SBC by manual boaring 100mm dia bore hole up to 6 mtr depth and performing SPT as per IS-2131 of 1996 collection of disturbed/undisturb soil sample take for test. In test case of gravely strata as refusal the open pit of 2 mtr depth if bldg work as directed by Engr-in-Charge and submission test report in triplicate. (ii) Conducting of necessary as test per relevant IS-Code/NBC 2005/SP-36 on all collected samples including the following: (a) Atterberg limits (Liquid limit, Plastic Limit and shrinkage limits) (b) Natural moisture content (c) Wet and dry density of soil. (d) Soil partical size distribution. (e) Triaxial shear test. (f) Shrikage test. (g) Consolidation test. (h) Specific grevity test for sand and rock. (j) Crushing strength test. (k) Premeability test. (l) Chemical analysis of ground water sample. (m) Free soil index. (n) Chemical analysis of soil. (iii) Submission of report of soil investigation along with photograph in pentuplicate duly annotated

(iv) Submittion of soil investigation report shall be with recommendation of type of foundation and SBC of soil at a suitable depth from AGL. SBC of soil at a depth of 1500mm & 2000mm shall also be workout for each bore hole. Water table if encountered during excavation shall also be reported for each bore hole along with soil profile.Expensive soil if encountered during excavation shall also be specified. Nos of holes for SBC = 07 Nos 6 mtr depth of each i.e.total 07x06 = 42 RM

Surface dressing not exceeding 15cm deep in soft/loose soil complete all as specified & directed.

Taking down old treatment incl paddding, removing existing bitumen felt treatment incl brushing,cleaning top surfaces of roof slab, broming etc complete all as specified.

Rendering 15 mm thick cement plaster with cement mortar(1:4) on fair finishes of brick work or concrete surface of roof slab all as specified.

Cement concrete tiles size 250x250mm, 22mm thick machine pressed over 15 mm screed in cement and sand mortar 1:6 set jointed and pointed in neat cement slurry in roof floors and cut and polished with mixture of white & grey cement in equal portion and no pigment complete, all as specified.

Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg/Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 4.0 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints and changes in direction should be covered with cement mortar 1:3 mixed with SBR latex @200ml/bag of cement and curved before laying of membarance. (c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrance and dusted with dry sand @ 0.50 to 1 Kg/sqm.

Note : (i) Roof treatment work shall be carried out through approved manufacturers only. (ii) If Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (iii) Covered fillet in PCC 1:2:4 type B0 using 12.5 mm graded crushed stone aggregate of required radius shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6).

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings, complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws, complete all as specified & directed.

Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specifed & directed.

15mm thick rendering in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces finished even and smooth without using extra cement, complete all as specified & directed.

10mm thick rendering in cement mortar 1:6 on other than fair faces of brick surfaces, finished even and smooth without using extra cement, complete all as specified & directed.

5mm thick rendering in cement mortar 1:3 on concrete surfaces of chajjas, upward fascias, ceiling and similar items, surface finished even and smooth without using extra cement, complete all as specified & directed.

Preparing of newly plastered surfaces of walls (plastered or unplastered surfaces) and applying two coat of oil bound distemper (white/tinted) over one coat of primer complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of white wash, complete all as specified & directed.

Preparing new surfaces, plastered or unplastered walls and applying two coats of cement base paints over one coat of primer all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash, complete all as specified & directed.

Repairs to balcony/Facia and soffit of chajjas etc by taking down old rendering 20 to 25 mm thick to match with the existing thickness in CM 1:3 and hacking clearly the edges and corners smooth and rounded for new plastered area exceeding 30sqm cm in width or girth complete all as specified.

Preparation of new plastered surgaces of wll & applying two coats of appex over a coat of primer complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) , complete all as specified & directed.

PCC (1:2:4) type B-2 100mm thick (using 20mm crushed stone aggregates) as in floors etc complete all as specified.

Machine pressed precast concrete interlocking paver block any shape and size conforming IS 15658-2006 of 60mm thickness M-35 grade over a layer and including 25mm thick sand cushioning complete all as spd and directed.

Demolition of reinforced cement concrte of any description & any in position not other wise specifically provided for kitchen shelves and chimney etc.

Reinforced cement concrete type B-1 (1:2:4) using 20mm graded aggregate as in kitchen shelves.

TMT reinforcement bars 10 mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer -in-Charge.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Green marble work 18mm to 20mm thick (table rubbed and polished) in steps of staircase/kitchen platform and like in cement morter 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade of green marble including 15mm thick screed bed/base in CM 1:4 roughening/cleaning to existing surface of old concrete floor by pickin sweeping clean and washing down with water to remove dirt/dust and brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and as approved by the GE/Engr-in-charge.

Roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust etc.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified & directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) of Gde BIIa area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4 complete, all as specified.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) of Gde BIIa area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:4 complete, all as specified.

Glazed ceramic tile 300 x 200 x 06-7mm thick (coloured) conforming to IS:13712 of 1993 on vertical surfaces such as dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed in cement and sand mortar 1:3 complete, all as specified.

18-22 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. (Size of Kota Stone slab shall be 52 cm x 52 cm).

Ditto all as per item No 37 here-in-before but in skirting/dado complete.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Taking down chowkats or frames of door/window/ventilators with shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Pressed steel frames (factory made) of size 125mmx66mm made out of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, bottom of each frame to be welded with 02 Nos. 25x25x3mm angle iron projecting 10cm on either side and PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate for filling of hollow portion, complete all as specified & directed.

Pressed steel frames (factory made) of size 105mmx60mm made out of 1.25mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, bottom of each frame to be welded with 02 Nos. 25x25x3mm angle iron projecting 10cm on either side and PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate for filling of hollow portion, complete all as specified & directed.

35mm thick factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified & directed.

30mm thick 2nd class hard wood (Sal/Hollock), glazed and skeleton shutters (factory made), open rebated and prepared to receive glass or gauge etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., size of members of shutters as specified in clause 8.24 (a) of SSR Part-I, complete all as specified & directed.

150mm ordinary rat tail rod pattern door spring including roller and roller plate of mild steel and fixed to wooden/steel door frame, complete all as specified & directed.

Butt hinges, medium weight, cold rolled, mild steel 100mm long, complete all as specified & directed.

Butt hinges, medium weight, cold rolled, mild steel 75mm long, complete all as specified & directed.

Aluminium handle, cast type, anodised, 150mm long, complete all as specified & directed.

Aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long, complete all as specified & directed.

100mm size Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified & directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, 250mm long, complete all as specified & directed.

Small fittings such as bracket of any type, latch and hinge blocks, shaped door and window stops and the like including all necessary labour, article not exc. 200 cucm each of 2nd class hard wood, complete all as specified & directed.

Steel windows/ventilator (Box type) factory made with double shutter (wire gauged shutter and glass/glazed shutter) wire cloth and glass panes shall be measured and paid separately of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete with two coats of synthetic enamel paint over one coat of red oxide primer all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh no 1/1 to 1/3 .

Mild steel framed work as in grills, gratings, grame work for eve boards etc. with ends of bars shouldered and or reveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 grade-E-165, complete all as specified & directed.

Mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified & directed.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

3mm thick figured glass pin head type and glazing with oil putty or wooden beads in squares not exc. 0.5 Sqm in each pane, complete all as specified & directed.

Floor door stopper 150mm length of aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor complete all as spd.

19/20mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber framed work as in cup board shutters, shelves etc., complete all as specified & directed.

2nd class hard wood (Sal/Hollock) plain, solid, straight chowkats/frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, with one or more rebates, complete all specified & directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet 5mm thick to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete as specified & directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified & directed.

20mm dia curtain rails of wooden texture, anodised aluminium alloy with fixing brackets, stops, rollers etc., complete all specified & directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified & directed.

50mm thick PCC 1:3:6, nominal mix, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in bays not exc 2 Sqm each, surface finished even and fair without using extra cement including filling of 6mm thick joints with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three part of sand by weight, complete all as specified & directed.

Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified.

Taking up or down steel tubing and connections, 20 mm bore fixed on walls, floors or ceiling etc complete all as specified and as directed by Engineer-in-Charge.

Ditto- all as per item No. 68 here- in- before but 15 mm bore.

20mm bore tubes, medium grade, galvanised with and including all fittings fixed to walls, floors, or ceiling or laid in floors etc complete all as specified and as directed by Engineer-in-Charge.

Refixing old steel tubing and connections in new or old position on walls, ceiling or floors etc of size 20 mm bore after cleaning including provn of new fittings all as directed by Engineer-in-Charge.

Ditto- all as per item No.70 here in before but 15mm bore.

Ditto- all as per item No.71 here in before but 15mm bore.

Bib taps, 15mm bore, cast copper alloy, with crutch or butter fly handle, screwed down, screwed for iron pipe, or brass ferrule, fixed in repairs, complete all as specifed & directed.

Stop valves, cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., fixed in repairs, complete all as specifed & directed.

Ditto- all as per item No.75 here in before but 20mm bore.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long, fixed in repairs, complete all as specified & directed.

Vitreous chinaware squatting pan, 'Orissa Pattern' size 580mm x 440mm with integral foot rests, white, with ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, fixed in repairs, complete all as specified & directed.

PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified & directed.

Towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, fixed to walls, complete all as specified & directed.

Stainless steel gratings 100mm bore size fixed with cement motar.

Plate rack made of stainless steel 0.8mm thick overall size 750mmx600mm complete all as specified.and directed.

Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm, fixed in repairs, complete all as specified & directed.

Ditto all as per item No 84 here-in-before but 75mm bore.

100mm bore sand cast iron soil waste and vent pipes ISI marked in any length with or without ears fixed in repairs to walls clamps and cement joints complete all as specified.

Ditto all as per item No 86 here-in-before but 75mm bore.

Ditto all as per item No 86 here-in-before but 50mm bore.

Cast iron cowl of 50mm bore, complete all as specified & directed.

Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, bore of pipe 75mm, complete all as specified & directed.

Sink with draining board made out of stainless steel 1.00 mm thick sheet for kitchen with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm with bowl size 410 mm x 330mm x 160mm supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge. Note : The Sink shall be ISI marked.

Demolition of brickwork or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified.

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:4 complete all as specified and as directed by Engineer -in-Charge

Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified and as directed by Engineer -in-Charge

Ditto all as per Srl item No. 95 here-in-before, but except bricks.

Supply only integral water proofing compound, complete all as specifed & directed.

Dismantling wall & ceiling board (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as specified & directed.

Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including 4 mm thick non asbestos designer ceiling board of size 600x600mm duly finished with three coats of white wash, complete all as specified & directed.

Dismantling structural steel work in framed truss n exc 10m in any section and shape.

Rolled mild steel work in roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W grade-E-250, including dismantling old mild steel angle, purlins complete all as specified & directed.

Sunken Floor treatment :- Providing and laying of water proofing treatment to sunken portion by applying cement slurry mixed with acralic based polymer modified cementitious composite compound of make as approved including demolation and filling of sunken floor. (a) First layer of slurry of cement @ 0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours. (b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/ Sqm his layer allowed to air cure for 4 Hours. Note : Concrete for sunken slabs shall be mixed with WP comounds as manufacturdrs instructions before carrying out water proofing treatment the sunken slab /dampeness is seen in ceilig below, then treatment is again carried out to RCC slab and it is again tested ( Water proof compound rate is superatly)

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar, internal dia of pipe 150mm, complete all as specifed & directed.

Concrete bed to 150mm bore drain pipes including packing under, and haunching against the sides of pipes after they are laid in cement concret 1:3:6 (Nominal mix) type C-2 using 40mm graded stone aggregate and tested, complete all as specified & directed.

Salt-glazed stoneware drain pipe, grade ‘A’ internal dia of pipe 150mm, laid in trenches and jointed, complete all as specified & directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching, internal dia of pipe 150mm, complete all as specified & directed.

Dismantling boarding (eve board) any description fixed in any position with nails.

Excavation in trenches n.exc 1.5m in width and n.exc 1.5m in depth and getting out in any type of soil for laying pipe line complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick with soft/loose soil as directed by Engineer-in-Charge.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified & directed.

Hardcore of gauge n exc. 63mm, deposited, broken bricks, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified & directed.

Cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregates) as in foundation filling and mass concrete complete, all as specified.

PCC (1:2:4) type B-2 100mm thick (using 20mm crushed stone aggregates) as in floors etc complete all as specified.

Plain cement concrete type B-1 1:2:4 (using 20 mm graded stone aggregates) as in copings including weathering, slightly rounded or chamfered angles and throating and necessary form works, all as specified .

Mild steel rolled work as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other coving, running rails and guides) and hanging; also fastening and fixing complete, conforming to grade Fe 410-W (Gde-E-250) Quality-A, all as specified.

Mild steel, plain, black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. all as specified.

Taking down carefully, copper / aluminium conductor unserviceable / perished point wiring (any type) for light/ fan/ light socket or power socket etc complete with fittings such as switches, sockets, ceiling roses, pendant holders, bracket holder, light fittings, regulators etc, including making good to disturbed surfaces of wall/floor etc, complete, all as specified & directed.

Taking down carefully unserviceable main switches, distribution boards of any type/size from their position including making good to disturbed surfaces of wall etc, complete all as specified & directed.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 1.5 Sqmm drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one light/fan point controlled by one way switch, complete all as specified & directed.

All as per Srl item No. 119 above but for one 3/5 pin 5 Amps socket outlet on same board .

All as per Srl item No. 119 here-in-before but for one 3/5 pin 5 Amps socket outlet on independent board.

All as per Srl item No. 119 here-in-before but one light point controlled by two numbers two way switches.

Point wiring with multi stranded FRLS PVC insulated unsheathed copper conductor cable single core of 2.5 Sqmm drawn drawn into and including PVC concealed conduit 'ISI marked' of 20mm dia medium grade as required, fixed in concealed surface of wall/ceiling including cutting chases as required, terminated in MS sunken box suitable for housing of switches, socket, regulator etc, covered with 3mm thick bakelite 'hylam' laminated sheet cover complete with all accessories including single core FRLS PVC insulated unsheathed multi stranded copper conductor cable of 2.5 sqmm for earth continuity conductor (green colour) and connected to earth dolly for one 3/5 pin socket outlet 15 Amps independent, complete all as specified & directed.

Notes for Srl Item No. 119 to 123 (i) Unit rate includes for cutting chases whereever required and sinking for boxes, making good to walls / floors etc., complete, including white wash / colour wash as directed. (ii) Uniform coding of wiring i.e red / yellow / blue for phase black for neutral and green for earth is to be maintained.

Switch socket combination, two in one, 6 pin type, 5 & 15 Amp, flush type universal, complete all as specified & directed.

Ceiling rose surface type, bakelite 65mmx50mm, 3 terminals, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole one way, complete all as specified & directed.

Switch piano flush type 5 Amps 240 Volt, single pole two way, complete all as specified & directed.

Bell push flush type, one way 5 Amps single pole one way, complete all as specified & directed.

Switch socket combination, two in one, 5 pin type, 5 Amp, flush type universal, complete all as specified & directed.

Socket outlet two in one, 5 pin type, 5 Amp, flush type, complete all as specified & directed.

Fan regulator, deluxe socket type (electronic step type) for 1200/1400 sweep AC ceiling fan including taking down old unserviceable fan regulator, complete all as specified and directed.

Bell, Ding Dong AC. 230 volts, single pole, complete all as specified & directed.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified & directed.

LED lamp in white colour of 15 watt, base Cap B-22, complete all as specified & directed. Make : Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya/ Havells

Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 02 ways double door type, ISI Marked including blanking plates where required & making good the disturbed surface of wall complete all as specified and as directed by Engineer-in-Charge.

MCB single pole, 240 volts of rating 6-32 Amps, all as specified and as directed by Engineer-in-Charge.

MCB single pole and neutral, 240 volts of rating 40 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge.

New generation energy saving and environmental friendly long life LED street light of 20W made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection and impact resistance of IK07 including GI bracket made of 40mm dia light grade GI tube 1.2 metre bend to shape with 02 nos FI clamp of 32x4mm with nuts, bots, washers, making connection with PVC copper conductor cable of appropriate size including taking down old unserviceable fittings, complete all as specified & directed. Make : Havells Cat Part No. ENDURA CITYLITEPLATSL 20W LED757SASYBOPC or equivalent of Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Energy saving 10W LED bulk head luminaires, IP-65, oval shape, surface mounted with all other accessories prewired and making connections with copper flexible twisted twin cord of appropriate gauge and length,230v, 50Hz including taking down old unserviceable fitting including taking down old unserviceable fittings, complete all as specified & directed. Make. Havells, Cat Part No.RUGBYNEONFT10WLED 760SSYMBOPC or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Surface & wall mounted, LED tube light fitting, 20W, glare free, smooth light distribution, 230v, box type, epoxy powder coated CRCA sheet housing with reflector cover channel, aesthetic looking end cap and HPF LED driver with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size, complete all as specified & directed. Make. Havells, Cat Part No. ENDURALINEARNEOBS 22WLED 865SPCWH or equivalent in Philips/ Crompton/ Bajaj/ Wipro/ Syska Led/ GE Lighting/ Surya

Taking down existing ceiling fan of any size and refixing the same after repair of building including provision of three core flexiable copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan, complete all as specified & directed.

Preparation of old painted surfaces of ceiling fan by scrubbing, cleaning with sand paper/wire brush etc making good surfaces and painting by applying two coats of whitensynthetic enamelled first quality paint over a coat of red oxide zinc chrome primer using spray gun in situ including filling cavities with filler and marking Srl No SM No / MES No with black paint, complete all as specified & directed.

Panel board fabricated of 2mm thick MS sheet of size 1.20 mx 0.80m x0.25m with opeaning of front door in two halves made of particle board (door opening shall be not less than 150 degree) having full hylem sheet inside door cutting/making holes for entry of pipes/cables, fitted with hinges and bolts for door lock. The panel of door shutters, fixed with steel hinges including 2 coats of good quality paint internally and externally by spray machine including dismantling of KWH (energy) meters and DB 4 Way box including MCB/TPN/SPN/SP and refixing the same complete and including wiring complete with FRLS insulated 6 Sqmm multi stranded and unsheathed copper cable all as specified.

Water heater storage type Geyser, electrically operated of capacity 25 Ltrs, 5 star rated vertical type rated power 2 KW with thermostat,safety valve, temp change regulator and mounting on wall by grounting nuts, bolts etc and making good distrubed surface complete including connecting outlet/inlet pipe line vent pipe etc all other accessories, all as specified and directed by Engineer-in-charge.

1100 volt grade heavy duty cable PVC insulated stranded aliminium conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspened by insulating hangers not more than 1 meter apart including 4mm suspension wire one twin core cable of size 10 sqmm complete all as spd.

25mm 3-layer PP-R Polypropylene random copolymer pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings complete all as specified.

Ditto all as per item No 147 but size 20mm bore. Note: Rate are inclusive cutting chases and making good disturbed surfaces.

Single phase exhaust fan double ball bearing heavy duty motor with protective bird guard of size 300mm sweep, 230 Volt 50Hz the frame of exhaust fan shall be fixed through rag bolts of suitable size including nuts, bolts and washer and connecting up with three core flexible copper stranded conductor cables from fan to ceiling rose complete all as specified and directed by Eng-in-charge.

Cutting in position existing GI pipe both side for taking branch connection supply and insertion of required fitting (20mm bore) including earth work of required size including all packing material & other fittings & fixtures for making the joint leak proof complete all as spd.

M/s Sekinder Paul Sharma