Shifting of Chief Engineer (E/Z) Officer RWD at Miao, Changlang district under RWD Jai-rampur Division, Arunachal Pradesh

Amount

Sub-Head :Type -II Quarters - 20Nos, Type-I - 6Nos & Bachelor Barrack - 4Unit

SH: Earth Work: Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m.

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH: Concrete Work: Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

SH: R.C.C. work.: Reinforced concrete work in foundations, footings, bases of columns etc. andmass concrete excluding cost of centring, shuttering and reinforcement in : a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surfac

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth an

Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surfa

Reinforcement of RCC work including bending, binding and placing in position complete. (b) Cold twisted bars.

SH: Brick Work: Brick work with best available local bricks in foundations and plinth in cement mortar 1:3 (1 cement :3 fine sand).

Extra for brick work with best available local brick in superstructure above plinth level upto floor two level.

Making plinth protection with 2nd class bricks on edge in cement mortar 1 : 6 (1 cement : 6 fine sand) over 7.50 cm bed of dry bricks aggregate 40 mm nominal size rammed consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1 : 2 (1 cement : 2 fine sand).

Construction brick masonry manhole with 2nd class bricks in cement mortar 1:5 (1cement : 5 fine sand) RCC slab with 1:2:4 mix ( 1 cement:2coarse sand:4 stone single 20mm nominal size). Foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1:2:4 mix ( 1 cement : 2 Coarse sand : 4 stone aggregate 20 mm nominal size) nearlly finished complete as per standard design. a)inside size 90 x80 cm and 45 cm deep including Cl cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg, (weight of cover 23kg and weight of frame 15 kg).

Making soak pit 2.5 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mm dia 1.8 m long complete as per standard design.

SH: Wood Work: Centring and shuttering including strutting, propping etc and removal of form work for : (A) Foundation, footings, bases of columns etc. and mass concrete.

(B ) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

(C) Lintels, beams, girders, bressumers and cantilevers etc.

(D) Column, pillars, posts and struts etc.

Providing and fixing flush door shutters, decorative type, core of black board construction with frame of 1st class hard wood and well matched 1st class teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. (

Providing approved best availlabe local wood(class-II) work in frames of doors, windows clerestory windows and other frames, wrought framed anhd fixed in position.

Supplying and fixing fully glazed shutters made out of best available hard wood for windows and clerestory windows using 7.5 kg/sqm 3 mm thick glass panes including applying one coat of approved wood primer. a) 35 mm thick in

Providing and fixing soft wood 'EVE' board 25 mm thick and 225 mm wide including painting two coats complete as directed.

Providing and fixing MS door latch with necessary screws etc complete. a) 300 x 20 x 6 mm

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. (a) 125 mm.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete. a) 150 x 10mm

b) 250 x 10mm for Doors

c) 100 x 10 mm for windows & Ventilators

Providing and fixing MS Hooks and Eyes.

Providing and fixing aluminum butt hinges anodised, transparent or dyed to required color or shade with necessary screws etc complete. a) 125 x 75 x 4 mm

b) 125 x 63 x 4 mm

SH: Steel Work: Steel work in Built up tubular trusses including cutting, hosting, fixing in position and applying a priming coat of approved steel primer welded and bolted includingspecialshaped washers etc complete (welding to be paid separately).

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flate, square or round bars with round headed bolts and nuts of by screws.

Providing and fixing 38 mm thick wire gauge shutters using galvanized mild steel wire gauge of IS Gauge designation 140G with wire of dia 0.56 mm for doors, windows and clerestory windows including anodized aluminium butt hinges with necessary screws

Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless screws etc. to side hung windows as per direction of Engineer-incharge complete.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. a) G.I. Pipes

SH: Floor: Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a) 75 mm thick

White glazed tiles 5mm. Thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1:3 (1 cement :3 coarse sand) painted with white cement slurry. a) Size of tile 1000X1000mm

SH: Drain: Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete.

SH: Roofing: Providing corrugated GI sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8mm dia with bitumen and GI limpet washers filled with white lead complete, excluding the cost of purlins, rafter and trusses.

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete. a) 0.80 mm thick GI sheet

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

SH: finishing: 15 mm cement plaster 1 : 3 (1 cement : 3 fine sand) on the rough side of single or half brick wall.

20 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying one coat of distemper primer of approved brand and manufacture on wall surface.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade.

Applying priming coat consisting of a mixture of red lead, white lead and double boiled linseed oil in the ratio of 0.7 Kg : 0.7 Kg : 1 Litre on wood work complete.

Painting (two or more coats) with suprior ready mixed paint for wood work ............

Applying priming coat with ready mixed genuine red lead paint of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting one or more coats with superior quality ready m.ixed paint for steel work of approved brand and manufacture in all shades on old work to give an even shade.

SH: Water supply: Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work). (a) 15 mm nominal bore

Providing and fixing brass bib cock of approved quality. (a) 15 mm nominal bore

Providing and fixing brass stop cock of approved quality. (a) 15 mm nominal bore

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality)complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing toilet paper holder.a) CP Brass

Providing and fixing CP brass shower rose with 15 mm or 20 mm dia inlet. b) 150 mm dia

CP brass towel rail

Providing and fixing 100mm sand cast iron grating for gulley, floors or nahni trap

Providing and fixing on wall face asbestos cement soil, waste and vent pipes including jointing with spun yarn soaked in bitumen and cement mortar 1 : 2 (1 cement : 2 coarse sand) complete. a) 100 mm dia

SH: Sanitary installation: Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or Strap, 12.5 Litre high level Cl flushing cistern (of approved make) with fittings RS or Cl brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

Providing and fixing CP brass waste for wash basins and sinks. (b) 40 mm dia

Providing and fixing MI fisher union for wash basin and sinks.a) 40mm dia

Providing and fixing sand cast iron(spun) soil, waste and vent pipes. a) 100 mm dia

Providing and fixing sand cast iron heel rest sanitary bend. (a) 100 mm dia

Cost of Haulage Excluding Loading and Unloading

Loading and Unloading of Cement or Steel by Manual Means and stacking.

Loading and unloading of stone boulder / stone aggregates / sand / kanker / moorum. (Placing tipper at loading point, loading with front end loader, dumping, turning for return trip, excluding time for haulage and return trip)

SH: INTERNAL ELECTRIFICATION & INSTALATION for Type-II Quarters - 20Nos, Type-I Quarter = 6 Nos & Bachelor Barrack = 4 Units: Wiring for light point with 1.5 Sqmm PVC insulated copper conductor cable in the surface conduit i/c painting etc as reqd. Short point

Medium point

Long point

Wiring for fan point with 1.5 Sqmm PVC insulated copper conductor cable in the surface conduit i/c painting earthing the regulator etc as reqd (Medium point)

Wiring for 3 pin 5 amp. Plug point 1.5 Sqmm. PVC insulated insuted copper conductor cable in surface i/c providing and fixing of 3 pin 5 amp. Socket outlet and 5 amp Tumbler/Piano type switch, earthing the third pin(Short point)

Wiring for 3 pin 15 amp. Plug point with 2.5 Sqmm. PVC insulated copper conductor cable in surface conduit i/c providing and fixing of 3 pin 15 amp. Socket outlet and 15 amp. Tumbler switch earthing third pin, painting etc. as required(Long point)

Wiring for circuit wiring with 2 x4 Sqmm. PVC insulated copper conductor single core cable in surface conduit i/c painting etc.

Supplying & fixing of ceilling rose on the existing wooden board i/c connection etc as reqd.

Supplying and fixing fancy wall bracket of anodised alluminium 12 mm dia fixed with brass bracket holder i/c conductor where required.

Supplying & fixing of brass batten angle holder i/c connetion etc as reqd.

Wiring for call bell point with 1.5 Sqmm. PVC insulated copper conductor cable in the surface conduit i/c painting etc as reqd.

Supplying & fixing of call bell & ball push suitable for AC/DC 1 ph 230V complete etc as required.

Wiring for Submain with 2X2.5 Sqmm PVC insulated copper Conductor single core cable in surface conduit i/c painting etc as required.

Supplying and fixing standard fan clamp suitable for fixing the 40 mm dia G.I Pipe for suspension on ceiling fan as required.

Providing & fixing of 60A metal clad TP & N switch fuse unit 415/500v with rewirable fuse i/c drilling holes on the board connection earthing the body etc as required.

Providing and fixing earth conductor for earth electrode with 4.06mm dia G.I wire in 1.5 mm dia earth electrode as required.

Supplying and fixing 4.06 mm dia GI wire on surface for recess for leap earthing as required.

Supplying of G.I pipe 40mm dia for 3.2 mtrs long for house service(Bracket complete with bend & clamps)

Pvdg. & fixing of 25x5mm strip in 40mm.

Supplying of 3 Pin socket 5 Amp

Supplying of 3 Pin socket 15 Amp

Supplying of switch 5 Amp

Supplying of Fan regulator

Supplying and fixing 18"x12" Teak wood board hings types locking arrangement including painting as required.

Supplying and fixing 10"x12" Teak wood board hings types locking arrangement including painting as required.

Supplying and fixing 8"x10" Teak wood board hings types locking arrangement including painting as required.

Supplying and fixing 7"x4" Teak wood board hings types locking arrangement including painting as required.

Supplying and fixing 4"x4" Teak wood board hings types locking arrangement including painting as required.

Providing PVC pipe for condute line-

PVC small round box

Providing and fixing Metal clead D.B 250 volt 15 Amp four way including drilling holeson the board, connection earthing the body etc as required. 2 Way

Supplying and fixing of 25/32 mm PVC casing caping along with the accessories on surface i/c,painting etc as required.

Supplying & fixing fan complete with box and other accessories suitable for 250/240v 50 Hz. 1ph for A.C supplying as required.

Supplying of G.I pipe 40mm dia for 3.2 mtrs long for house service(Bracket complete with bend & clamps)

LED 14 WATT watts with all accessories.(Havels make)

MCB box 6way

Isolator 40 Amp

Supplying & fixing MCB Switch 10 Amp.

Supplying & fixing of MCB suitable for 5-15 amp. For operating 230 V AC

Supplying of 6 Sqmm WPTC

Supplying of 1 phase Energy meter.

Change over 200 Amp

Earthing with Cu. Earth plate 600 mm x 600 mm x 3 thick i/c accessories & providing mansory inclosures with cover plate having locking arrangement & watering pipe etc. ( But without charcoal or coke salt) complete as required.

Supply of Cu earthing wire 1 mm.

Supplying of G.I earthing pipe.

Extra for using charchol

SUPPLY OF FURNITURE FOR TYPE-II QUARTER - 20 NOS, TYPE-I - 6 NOS & BACHELOR BARRACK - 4 UNIT: COT{SINGLE}

WRITING TABLE WITH DRAWER

WATER FILTER

CENTRE TABLE

MEAT SAFE

PLASTIC CHAIR with cushion

Plastic Chair

Dinning Table

Retaining Wall:

Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work.) (i) Ordinary soil (A) Manual Means (Depth upto 3 m)

Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and Technical Specification (a) Square Rubble Coursed rubble masonry( first sort )

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and Technical Specifications Coursed rubble masonry (first sort )

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specifications

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification (A) Granular material

Security Chainlink Fencing

Providing Security fencing Wall having height 1.90mtr with RCC pillar of size 0.20mtr x 0.20mtr @2.00mtr center to center, brick panel walls 1.00mtr height. And chain link fencing 0.90mtr. Ht. with iron angle post 50x50x6mm size bend at 45° and bend portion 0.30 mtr. lenght with 3 rows of barbed wire at top(total length of angle iron is1.2mtr.+0.30 mtr.)

Septic Tank for 100 Users - 1No

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Providing and laying cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in : a) Foundations and plinth

Brick work with best available local bricks in foundations and plinth in cement mortar 1:4 (1 cement : 4 fine sand).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in : (a) M20 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size).

12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Neat cement punning.

Reinforcement of RCC work including bending, binding and placing in position complete.a) Tar/ TMT steel

Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.a) 100 x 100 x 100 mm

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. a) 100 mm dia

Providing and fixing terminal guard : 100 mm. (a) Sand cast iron S&S as per IS - 1729.

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes

Centring and shuttering including strutting, propping etc. and removal of form work for: a) Foundation, footings, bases of columns etc. and mass concrete.

b) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

Carriage charge of Cement & Steel from Tinsukia (Qnty as per TC)

Carriage charge of Sand from nearest quary at Joypur (in Assam) (Qnty as per TC)

Carriage charge of bricks from brick field in Margerita in Assam (Qnty as per TC)

Loading and unloading of stone boulder / stone aggregates / sand / kanker / moorum. (Placing tipper at loading point, loading with front end loader, dumping, turning for return trip, excluding time for haulage and return trip)

Loading and Unloading of Cement or Steel by Manual Means and stacking.

RCC Over Head Water Tank for 43000 Litres - 1No

Earth work in excavation in foundation trenches not exceeding 1.50 m width or 10 Sq.m. on plan or drains not exceeding 1.50 m in width or 10 Sq.m. on plan including dressing of sides and ramming of bottoms, lift upto 1.50 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a) O/Soil

b) Ordinary Rock (with or without blasting)

Providing and laying in foundations and plinth cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in a) M20 (1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement. a) M20 (1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20 (1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement: 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding C<l§t of ce\itring and shuttering' and reinforcement with M20 (1 cement: 1.5 coarse sand: 3 stone aggregate 20 mm nominal size).

12 mm cement plaster 1 : 3 (1 cement: 3 fine sand).

Reinforcement of RCC work including bending, binding and placing in position complete.

Centering and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete.

e)Column, pillars, posts and struts etc

d) Lintels, beams, girders, bressumers and cantilevers etc.

b) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Providing and fixing normal gauge HD polythene pipes of approved quality/complete with special flange compression type fittings (of approved make) including trenching and refilling etc (external work).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of appr ved steel primer using structural steel etc . . d ' as require . b) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

MAITUNGTIKHAK