SPL REPAIR TO BOUNDARY WALL AT FOL GROUP OF 54 COY ASC (SUPPLY ) TYPE C UNDER GE (WEST) JABALPUR

Amount

Taking down cement plaster etc on brick walls/ concrete (ceiling) surfaces of any descriptions including racking out joints, hacking for keys, scrubbing down with water and disposal of unserviceable materials to out side of MD land complete all as specified & directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete including removal of debris to out side MD land complete all as specified & directed.

Dismantling of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar ficings, dressed stone work and pre-cast concrete articles complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in any type of soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated material exc. 50 m but n exc 250 m, depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) Type D-2 using 40 mm graded crushed stone aggregate as in foundation, filling, mass concrete and sub base of floors, path/ paving etc complete all as specified & directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, rough finished surface of concrete, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. ( Note : Reinforcement shall be measured and paid for separately against relevant items of BoQ)

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions,rough finished surface of concrete, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed. ( Note : Reinforcement shall be measured and paid for separately against relevant items of BoQ)

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. , rough finished surface of concrete, complete all as specified and directed.

M&L for RCC M-25 (Design Mix) using 20mm graded stone aggregate as in lintel beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. ( Note : Reinforcement shall be measured and paid for separately against relevant items of BoQ)

M&L for brick work with sub class 'B' fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified & directed.

M & L for PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in bed block complete all as specified and directed.

M&L for 15mm thick rendering in CM (1:6) on fair faces of brick work , finished even and smooth without using extra cement complete all as specified & directed.

M&L for mild steel TMT bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia and over, as in stirrups, spacers and binders for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel work conforming to Fe-290 Gde E -165 as in posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc; flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed.

S&F galvanised Mild steel concertina coil of 600 mm dia of approved type/make as approved by GE, for laying on y shape angle fixed on boundary wall etc complete all as specified and directed.

S&F, Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

M&L for preparation of new surfaces of iron/ steel of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer as approved by GE complete all as specified & directed.

M&L for prepration of new plastered surfaces of walls and applying two coats of cement base paint over & including a coat of cement base primer complete all as specified & directed.

Schedule of credit amount of Rs 70275.00 to be deducted during AOC

M/s PARASRAM MULCHANDANI (BID ID -3085737)

Tiki Water proofing Co (BID ID -3076052)

J.P ENTERPRISES (BID ID -3091755)

M/S Modern builders (BID ID -3087326)

M/s Ram Associates (BID ID -3091879)

New Era Engineers (BID ID -3091903)