CERTAIN PETTY REPAIR OF E/M COMPLAINT OF INTERNAL ELECTRIC SUPPLY AT PCDA (NC) OFFICE AND RESIDENTIAL COMPLEX AND SPECIAL REPAIR TO TOILET AT PCDA (NC) COMPLEX UNDER GE JAMMU

Amount

E/M Portion: - Charges for attending E/M petty complaint in respect repair/rectification of fault in electric fitting MCB DB's, internal wiring LT Panel and fixture and rectify the faults and replacement of unsv any type of fitting/fixture, MCB's, any type, bakalite sheet restore the electric supply and made the item functionable light point, fan point, socket point 5A/15A, switches sockets, fan regulator, light fixtures any type of lamp, MCB DB's and all electrical acessories and day to day /door to door maintenance, making the points/accessories serviceable in all respect with replacement of any minor parts like small length of wires (not more than 1 mtr) and other connected minor accessories. Work shall also include to check and removal of leakage in service connection / submains of houses all as specified and as directed. The scope also include cutting of existing bakelite sheet to accommodate new wiring acessories all type electric fitting/fixture. (Accessories shall be paid under respective items).

Notes : Any other replacement of major items shall be measured & paid under respective items as supply only. Fixing charge of fitting/fixture and MCB's of any type is deemed to be included in the above item.

(i) Contractor representative/engineer will report to complaint cell for morning and afternoon to collect routine/urgent nature of complaint related to internal electric supply till completion of contract. The work shall be attended by the contractor immediately. The contractor will ensure availability of manpower (two electrician and two helper) equipped with all sort of petty items such as insulation tape, galvanised screws, nuts, bolts, washers etc required to accomplish the job. The contractor will also ensure as availability of every type of requisite T&P items to his tradesman. All routine / urgent job received on job slip will be repaired and got signature of user's and will be deposited to complaint cell within 24 hrs. In case of any delay in attending the complaint more than 12 hrs after handing over of routine / urgent works, the contractor shall be liable to pay the penalty as per the item rate. (ii) Contractor shall maintain the maintenance register showing all daily complaints received and shall maintain job card for attending complaints. The signature of the user shall be obtained on the job card showing the materials used in the work after completion of the job. (iii) If the Contractor did not attend complaints, a penalty of Rs 300/- per day per complaint recovery shall be made from the work done amount. (iv) The MES Department is not responsible for the payment of staff hired by contractor for complaint rates for attending the complaints by the electrician are deem to included in the item for repair i.e. Electrician/Helper, as all the items of CA are to be supply and fixed by the contractor. (v) Proper record (date wise) of complaints received and rectified by the contractor shall be produced for verification at the time of payment of each RAR/Bill. (vi) All the complaint slip, register and connected document will be provided by the contractor without any extra cost. (vii) After any repair the site has to be cleaned and make the surface good.

Supply only switch piano, flush type single pole one way 5 Amp, 240 volts ISI marked complete all as specified and as directed.

Supply only socket outlet 2 in 1, 3 pin, 5 A complete all as specified and directed.

Supply only switch socket outlet combined 5 pin, 5 amp flush type, 240 volts ISI marked complete all as specified and directed.

Supply only switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 volts ISI marked complete all as specified and directed.

Supply only socket outlet 3 pin, 15 Amp, flush type, 240 Volts, 6 pin flush type complete ISI marked complete all as specified and directed.

Supply only switch piano, flush type single pole, one way 15 Amps, 240 volts ISI marked complete all as specified and directed.

Supply only ceiling rose, 3 terminal surface type complete all as specified and directed.

Supply only lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply only bell, AC 230 Volts, single pole complete all as specified and directed.

Supply only bell push flush type single pole one way 5 amp complete all as specified and directed.

Supply only holder any type for batten fitting including taking old one ISI marked complete all as specified and directed.

Supply only MCB SP 6 to 32 Amps, 240 Volt 'B' series complete all as specified and directed.

Supply only SPN 32 Amp rating 240V, 10 KA 'B' curve miniature circuit breaker (MCB) complete all as specified and directed.

Supply only SPN 40 to 63 Amp rating 240V, 10 KA 'B' curve miniature circuit breaker (MCB) complete all as specified and directed.

Supply only stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed.

Taking down old unsv copper/aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden/iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/steel conduit and into existing CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Notes : (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

Description all as per serial item No 18.00 here-in-before but one 5 pin socket outlet, 5 amps on the same board complete all as specified and directed.

Description all as per serial item No 18.00 here-in-before but one 5 pin socket outlet, 5 amps, independent complete all as specified and directed.

Description all as per serial item No 18.00 here-in-before but for one 5 pin socket outlet 15 Amps on Independent board with cables 2.5 sqmm size complete all as specified and directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid / 1.8mm wall thickness ISI marked including new CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note : (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

Description all as per serial item No 22.00 here-in-before but 5 Amp socket outlet on same board complete all as specified and directed.

Description all as per serial item No 22.00 here-in-before but socket outlet 5 Amps independent board complete all as specified and directed.

Description all as per serial item No 22.00 here-in-before but for one 6 pin socket outlet 15 Amps on independent board with cables 2.5 sqmm size complete all as specified and directed.

Description all as per serial item No 22.00 here-in-before but drawn through and including new surface conduit PVC rigid non metallic conduit 20 mm dia for socket outlet 5 amp independent board complete to accomodate the accessories for PVC Gang Box all as specified and as directed.

Description all as per serial item No 22.00 here-in-before but drawn through and including new surface conduit PVC rigid non metallic conduit 20 mm dia for socket outlet 15 amp independent board complete to accomodate the accessories for PVC Gang Box complete all as specified and directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid / 1.8mm wall thickness ISI marked including pressed steel with existing colour terminated boxes of Modular Metal flush Boxes of any way i.e. (1 to 8 way as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:- Note: Suitable Module white cover sheets with frame as specified to be provided in replacement to MS/Galvanised sunken boxes and measured & paid separately as per relevant item. Note : (a) Wiring shall be done by using proper colour coding (b) Earth wire shall be of green colour (c) On RCC roof/celing PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engr-in-Charge.

Description all as per serial item No 28.00 here-in-before but 5 Amp socket outlet on same board complete all as specified and directed.

Description all as per serial item No 28.00 here-in-before but socket outlet 5 Amps independent board complete all as specified and directed.

Description all as per serial item No 28.00 here-in-before but for one 6 pin socket outlet 15 Amps on independent board with cables 2.5 sqmm size complete all as specified and directed.

S&F in replacement Modular switch 1 way 6 A,1 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular switch 1 way 16 A, 1 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Socket, 6A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Socket 6A/16A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Fan step regulator, 120W 1 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 1 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 2 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 3 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 4 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 6 module, 240 volts ISI marked complete all as specified and directed.

S&F in replacement Modular white cover plate with frame 8 module, 240 volts ISI marked complete all as specified and directed.

M&L for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

M&L for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

M&L for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

S&F in replacement MCCB 4 pole, 415 Volt fixed thermal and fixed magnetic setting of cap 125 Amps 16 KA complete all as specified and directed.

S&F in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement of SPN 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing in replacement of SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing in replacement of 415V 10KA 'B' curve TPN 40 to 125 Amp miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning complete all as specified and directed.

S&F in replacement for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and directed.

S&F in replacement for switch piano, flush type single pole one way 15 Amps, 240 volts complete all as specified and directed.

S&F in replacement for socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed.

S&F in replacement for socket outlet 5 pin, 15 Amp, flush type, 240 volts, 6 pin flush type complete all as specified and directed.

S&F in replacement for switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and directed.

S&F in replacement for switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 volts complete all as specified and directed.

S&F in replacement for bell push, flush type single pole, 5 Amp, 240 volts complete all as specified and directed.

S&F in replacement for ceiling rose 3 terminal surface type complete all as specified and directed.

S&F in replacement for lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F in replacement for self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed.

S&F in replacement for LED lights fitting 1x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 volts 50 Hz complete all as specified and directed.

S&F in replacement of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement bulk head luminaries IP65 with opal diffuser 10 watt, 230 volts LED type complete with 10 watt LED Bulb complete all as specified and directed.

S&F in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed.

S&F in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc complete all as specified and directed.

S&F in replacement calling bell Ding Dong / buzzer AC 230 Volts, single pole complete all as specified and directed.

M&L in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sq mm for phase and neutral and one run of 4.0 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note : Wiring shall be done in proper colour coding.

M&L in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 4 Sq mm for phase and neutral and one run of 2.5 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note : Wiring shall be done in proper colour coding.

M&L in replacement for wiring for circuit with proper existing colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 1 run 2.5 Sq mm for phase, drawn through the existing rigid PVC concealed conduit fixed on wall complete all as specified and directed. Note : Wiring shall be done in proper colour coding.

M&L in replacement for wiring for circuit with proper existing colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 1 run 1.5 Sq mm for phase, drawn through the existing rigid PVC concealed conduit fixed on wall complete all as specified and directed. Note : Wiring shall be done in proper colour coding.

M&L for Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion including taking down old unsv earthing complete with galvanised mild steel earth plate electrode complete all as specified and directed.

S&F in replacement unsv wooden/CI Shunken box with new CRCA pressed steel terminal box of size 7X4' including taking down old complete with cemented and patch work complete all as specified and directed.

S&F in replacement unsv wooden/CI Shunken box with new CRCA pressed steel terminal box of size 4X4' including taking down old complete with cemented and patch work complete all as specified and directed.

S&F in replacement unsv wooden/CI Shunken box with new CRCA pressed steel terminal box of size 10X8' including taking down old complete with cemented and patch work complete all as specified and directed.

Supply and fixing in replacement Bakalite hylum sheet 3 mm thick complete with cutting and making size for fixing switches (06 No's each) of size 8''X5'' complete all as specified and directed.

Supply and fixing in replacement Bakalite hylum sheet 3 mm thick complete with cutting and making size for fixing switches (12 No's each) of size 12''X10'' complete all as specified and directed.

Supply and fixing in replacement Bakalite hylum sheet 3 mm thick complete with cutting and making size for fixing switches (02 No's each) of size 5''X5'' complete all as specified and directed.

Supply and fixing in replacement of plug top 15 Amps complete all as specified and directed.

S&F in replacement of vertical distribution board (TP&N) 4 way double door suitable for and including MCCB 125 Amp 16 KA four pole as incomer and out going MCB's and should be IP 43 protected with copper bus bars, neutral links, Earthing bar complete all as specified and directed including taking down old UNSV DB/MCB any type. Note:- (i) Rate includes MCCB four pole 125 Amp, 16 KA, 415 volts with adjustable thermal settings. (ii) MCB's shall be measured and paid separately. (iii) TPN DB and MCCB should be of same make.

S&F in replacement PVC box (gang box) surface mounted heavy duty 3 way complete with socket outlet 2 in 1, 6 pin 5 amp 240 volt along with switch piano 5 amp 240 volt complete all as specified and directed.

S&F in replacement PVC box (gang box) surface mounted heavy duty 3 way complete with socket outlet 2 in 1, 6 pin 5 amp 240 volt along with switch piano 15 amp 240 volts complete all as specified and directed.

Notes: - (i) For Serial No 17 to 82 : The Contractor has to complete the work assigned for above items within 72 hrs failing in which recovery at the rate 25 Rs. per complaint per day. (ii) The MES Department is not responsible for the payment of staff hired by contractor for complaint rates for attending the complaints by the electrician are deems to included in the item for repair i.e. Electrician/Helper, as all the items of CA are to be supply and fixed by the contractor. (iii) Proper record (date wise) of complaints received and rectified by the contractor shall be produced for verification at the time of payment of each RAR/Bill. (iv) All the complaint slip, register and connected documents will be provided by the contractor without any extra cost. (v) After any repair the site has to be cleaned and make the surface good.

Labour for repair/servicing of ceiling fan of any capacity complete with strip opening the ceilling fan for repair/washing/warnishing and removing of old lubricating substance from bearing/bush using Kerosine oil, carrying out fresh lubrication using grease and to make the ceiling fan noise free for smooth functioning, including replacement of worn out/unserviceable minor spare parts split pin, fan body bolts, spring washer, fan rod bolt etc and PVC insulated, unsheathed stranded twin twisted copper conductor cable of size 1.5 Sqmm up to 1.0 M long, assembling the repaired ceiling fan and testing to the entire satisfication of Engineer-in-Charge and depositing in MES Store yard. (Replacement of spares flexible wire etc/rewirding of ceiling fan shall be measured and paid seperately under respective item for material and labour cost.)

Description all as per serial item No. 84.00 here-in-before but for exhaust fan of any type mm sweep complete all as specified and directed.

Description all as per serial item No. 84.00 here-in-before but for wall mounting fan of any size/ type complete all as specified and directed.

Rewinding of ceiling fan, of any make/type and size (1200/1400 mm sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufacturer's specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stator/rotor, connection and testing complete all as specified and as directed.

Description all as per serial item No 87.00 here-in-before but for exhaust fan of any make/type and size complete all as specified and directed..

Description all as per serial item No 87.00 here-in-before but for wall mounting fan of any make/type and size complete all as specified and directed.

Labour for remetalling of worn out shaft of fan, cutting, brazing, machining and polishing to make the shaft suitable for fixing of new ball bearing and fixing ball bearing in replacement of bushing system in ceiling fan and assembling the same and testing to the satisfaction of Engineer-in-Charge to ensure smooth and noise free operation complete all as specified and directed. Note: - Bearing shall be measured and paid separately.

Supply and fixing ball bearing of any size and type, suitable for any type/make/size of ceiling fan complete all as specified and directed.

Description all as per serial item No 91.00 here-in-before but for exhaust fan of any type/make and size complete all as specified and directed.

Description all as per serial item No 91.00 here-in-before but for wall mounted fan of any type/make and size complete all as specified and directed.

Supply, fixing in replacement of capacitor 230 Volt AC 50 Hz, conforming to IS-1709 and rated capacity 2.5 MFD for ceilling fan, Exhaust Fan and Wall mounted Fan complete all as specified and directed.

Description all as per serial item No 94.00 here-in-before but of rated capacity 4.0 MFD for Exhaust Fan complete all as specified and directed.

Supply and connection of PVC insulated, unsheathed multi stranded, three core twisted copper flexible cable of size 1.5 Sqmm as required complete all as specified and directed.

Supply and fixing only bush of suitable size for exhaust fan of any type/size as per existing type complete all as specified and directed.

Description all as per serial item No 97.00 here-in-before but suitable for wall mounted fan of any type/size as per existing type complete all as specified and directed.

Supply and fixing of PVC connector 4 way 6 Amps with connection screws, nuts complete all as specified and directed.

Supply and fixing of PVC clamps with fixing screws for holding capacitor of any type and size complete all as specified and directed.

Supply and fixing of GI/ MS anodized bolts with anodized nuts, spring washers, split pin etc size 50 mm long 10 mm dia half threaded type with split pin hole complete all as specified and directed.

S&F in replacement MS clamp for down rod of suitable size including gromet / reel type rubber pad with bolts, nuts, split pin and washers suitable for housing ceiling fan complete all as specified and directed.

S&F in replacement of ceiling fan down rod 12 mm dia and 30/45 cm long complete with MS Clamp Rubber reel, split pin nut bolts etc complete all as specified and directed.

Supply and fixing in replacement of louver shutter made of MS sheet metal 1.2 mm thick for round base and 0.8 mm thick for flaps, comprising of mounting legs frames made of MS flat strips of size 25mm x 3mm includidng heavy duty rust proof passivated bolts of size 50 mm long 8 mm dia to be fixed on wall at ground/First/Second floor etc complete with using fastener bolt, driling for exhust fan up to 400 mm sweep including taking down old one complete all as specified and directed. Notes: - (i) Rates are deemed to be including charges for hiring any type of T&P ladder, cutter etc. (ii) Contractor shall be responsible for life care of staff deployed for fixing louver shutter.

Cleaning of ceiling fan assembly of any type/size and carrying out two coats of spray painting with first quality synthetic enamelled paint of approved colour, including writing of MES number in black paint complete all as specified and directed.

Description all as per serial item No 105.00 here-in-before but for exhaust fan upto 450 mm complete all as specified and directed.

S&F in replacement PVC canopy set of two pieces for ceiling fans of any size complete all as specified and directed.

Repair to oscillation moving part of wall mounted fan including replacement of all wornout components, bearing, lubrication and assembling complete all as specified and directed.

Repair/Maint/Servicing to AC's of any capacity and model by replacing capillary tubing, gas chargings, rectification of leakage in capillary tubing/Chiller plant/water tanks, condensing coils, repair to wiring, flushing/cleaning, condensing/cooling coils/internal/External unit of split AC, greasing to blower motors, replacement of spare parts, fan belts and make refrigerator/deep freezer/water coolers/AC's in serviceable condition complete all as specified and directed by Engr-in-Charge. Note: - Spare/Gas charging shall be paid separately.

Charges for fixing in replacement of unsv sealed seamless welding compressor unit company manufacturer of any capacity for AC's complete with initial filling/charging of refrigerant gas to meet the requirement complete with vibration rubber pads four no's each nut, bolts etc and testing on full load complete all as specified and directed by Engr-in-Charge. Note: - Spare parts shall be measured and paid separately under respective items. Note: - "Contractor shall be responsible for all replacement of failed compressor and shall be accompanied by certificate from the original compressor to the effect that said compressor has been repaired at their authorised service center. Further, a warranty of 12 months shall be provided on such replacement in writing."

Supply only sealed compressor unit seamless welding company manufacturer with filling of refrigerant gas conforming to ISI as under: -

Split/Window AC 1 Ton Capacity

Split/Window AC 1.5 Ton Capacity

Split/Window AC 2.0 Ton Capacity

Supply and fixing in replacement of unsv/burnt condensing fan motor 1/35 HP single phase 230 volt 50 Hz complete with blade, fan belts for water cooler of capacity 40/80 Ltr and 60/120 ltr complete all as specified and directed.

Supply only condensing fan motor 1/5 HP 1440 rpm single phase 230 Volt 50 Hz with double blade and shaft end with fan belts for windows AC/Split AC conforming to ISI of capacity 1.5/2.0 ton complete with vibration parts etc complete all as specified and directed.

Supply and charging refrigerant 134a/R-22 in sealed compressor unit of refrigerator/deep freezer / water coolers / AC's of any type and capacity after flushing the complete system with carbon tetrachloride (CTC) and vacuumise the complete system with vacuum pump and testing on full load including replacement of filter, strainer complete all as specified and directed.

Supply and fixing in replacement of following spare parts for AC's of any capacity : -

Starting relay

Overload protector

Thermostat switch

Defroz switch

Supply and fixing in replacement of unsv following spare parts of window/Split AC unit of capacity 1.5 to 2.0 ton: -

Starting capacitor 36/40 mfd

Running capacitor 100/120 mfd

PCB of Split AC

Front Grill cover for window AC 1.5 Ton

Condensing fan motor double shaft

Supply and fixing in replacement of PVC flexible branded pipe of 20 mm dia for split AC water drain out complete all as specified and directed.

Supply and fixing in replacement of outer split AC condensing unit complete for split AC 1.5 ton complete all as specified and directed.

Supply and fixing in replacement of inner unit of split AC complete with filters, blower motor etc for split AC 1.5 ton complete with all accessories complete all as specified and directed.

Supply and fixing in replacement of copper capillary tubing 5/8'' for AC connection/repair complete all as specified and directed.

Supply and installation for replacement of automatic voltage stabiliser with back boost relay working range 90 to 290 Volt at 230 Volt of capacity 5 KVA complete all as specified and directed.

S&F in replacement for Socket outlet 5 pin, 5 Amp, flush type complete all as specified and directed.

S&F in replacement for Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified and directed.

Taking down existing UNSV Exhaust fan repair/Maint including replacement unsv spare parts i.e. bearing, bush, PVC connector, PVC clamp, canopy, capacitor, including painting, rewinding of any make/type and size with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfacory RPM as per manufacturer's specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stator/rotor, connection and testing complete all as specified and directed.

Notes :- (i) For Serial No 84 to 125 : The Contractor has to complete the work assigned for above items with in 72 hrs failing in which recovery at the rate 25 Rs. per complaint per day. (ii) The MES Department is not responsible for the payment of staff hired by contractor for complaint rates for attending the complaints by the electrician are deemed to be included in the item for repair i.e. Electrician/Helper, as all the items of CA are to be supply and fixed by the contractor. (iii) Proper record (date wise) of complaints received and rectified by the contractor shall be produced for verification at the time of payment of each RAR/Bill. (iv) All the complaint slip, register and connected documents will be provided by the contractor without any extra cost. (v) After any repair the site has to be cleaned and make the surface good.

B/R Portion: - Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings complete all as specified and directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm complete all as specified and directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20mm complete all as specified and directed.

Refixing only 15mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

Refixing only 20mm dia steel tubing and connections in new or old position including cleaning of old steel tubing complete all as specified and directed.

Taking down chowkats or frames n.exc 1.5 sq.m each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down Chowkats or frames exc 1.5 sq.m but n.exc 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails Mild steel frame shall be coverred with heat moulded plain cover PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail. lock rail and bottom rail on either side and gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site including two No's 200mm tower bolt and bow handle each shutter as per specification clause No 8B 2.1 to 8B.10 and drawing on page No 178 of MES SSR-2020 Part-II complete all as specified and directed.

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube including three no's 100mm stainless steel butt hinges each frame, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F box type steel windows (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes complete all as specified and directed and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3. Notes:- The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 No's MS steel lugs made of 20X5 mm iron flat 200 mm long (iii) PCC block for embedding lugs (iv) Cooler windows where required (v) 10 mm square framed guard bar

Preparation of newly steel surface of any description applying two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, of size 15mm dia bore complete all as specified and directed.

S&F in repairs Bip tap standard of PTMT any colour screwed for iron pipe and fixed (Minimum weight 15mm - 90gms) of 15mm dia bore including necessary fittings complete all as specified and directed.

Supply and fixed in repairs PVC connection 15mm bore size with PTMT of length 600 mm long with brass or PVC nuts and PVC washer complete all as specified and directed.

Supply and fixed in repairs high density polyethylene (HDPE) waste water pipes of pressure rating 6 kgf/sq. cm of bore dia 32 mm and 600 mm minimum length (Adjustable type) complete all as specified and directed.

Cleaning of water storage tank completely by removing all scale dirt/dust of any description complete all as directed at site and writing date of cleaning with synthetic enamel paint including all material and labour of capacity ranging exceeding 250 ltrs and upto and including 2000 ltrs including dismantling and refixing if required complete all as specified and directed.

S&F in repairs CP brass jet spray with flexible pipe not less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and directed.

S&F in repairs PVC flushing cistern 10 ltr capacity ISI marked make should be engraved on the body including flushing pipe PVC 90 cm long, pair of bracket with angle valve and PVC connections etc complete all as specified and directed.

S&F in repair Vitreous china squatting pan 'Orissa' pattern size 580x440mm white, with integral foot rest 'P' or 'S' trap, front or back inlet including connection to trap and to flushing pipe, anti-syphonage pipe etc. complete making good to floor as existing complete all as specified and directed by Engr-in-Charge.

S&F in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts, flush pipe and joints complete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china urinals, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with grating and union for discharge pipe, including PVC waste pipe 32mm of suitable length, CP waste coupling 32mm dia suitable for urinals, PVC connection 15x 450mm long, CP urinal spreader, 15 mm angle valve fancy type chromium plated complete all as specified and directed by Engr-in-charge.

S&F in repairs Vitreous china wash hand basin white, flat back of size 550x400mm with PVC connection (15x450) mm long with PTMT nuts and PVC washer and including cutting for pinning in ends, pair of cast iron brackets and provision of PVC waste pipe 32mm of adequate length, CP waste coupling 32 mm dia of half or full threaded, chromium plated fancy type angle valve 15 mm dia bore and taking down unserviceable wash hand basin complete all as specified and directed by Engr-in-Charge.

S&F in repairs 125 mm dia steel grating fixed in position complete all as specified and directed.

S&F in repair Health faucet with 1 mtr long flexible pipe comlete all as specified and directed.

S&F in repair 75 mm dia cast iron bends any radius diminishing pieces or tapers (large bore measured) fitted with oval access door complete all as specified and directed.

S&F in repair 100 mm dia cast iron bends any radius diminishing pieces or tapers (large bore measured) fitted with oval access doors provided with cement joint complete all as specified and directed.

S&F in repair cast iron 100 mm dia bore pipe, branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval access doors provided with cement joint complete all as specified and directed.

S&F in repair 75 mm dia soil, waste and vent pipes, (sand cast pipes) in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S&F in repair 100 mm dia soil, waste and vent pipes, (sand cast pipes) in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S&F in repairs 100 mm cast iron sanitary connection short connection pipe of length up to 450mm complete all as specified and directed.

S&F in repairs 75mm dia cast iron floor trap with grating including jointing with waste pipe fixed with cement concrete 1:2:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. (Glazed tiles) complete all as specified and directed.

M&L for non skid ceramic coloured designer seamless tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured designer seamless tiles 300x450x7 to 8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in coloured cement to match with the surface over and including 15mm thick screed in CM 1:4 complete all as specified and directed.

Dismantling water tanks exceeding 500 and not exceeding 1000 ltr complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position complete all as specified and directed.

S&F in repair cover of CI oval acess door with bolts and rubber gasket to make it water tight for 100 mm bore CI bends complete all as specifed and directed by Engineer-in-Charge.

S&F in repair cover of CI oval acess door with bolts and rubber gasket to make it water tight for 75 mm bore CI bends complete all as specifed and directed by Engineer-in-Charge.

Demolition of cement concrete of any description and in any position and removing the rubbish from work site complete all as specified and directed.

M&L for preparing surface of sunken slab and applying 15 mm thick cement plaster in CM 1:4 with liquid water proofing compound Pedilite LW plus @ 200 ml per 50 Kg of cement both on floor and wall finished surface even and smooth. The surface shall then be cured and filled with water for 48 hours and allowed to dry then apply APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) laid with 75 mm side overlap and 100 mm overlap on primed surfaces by forced application as per manufacturer's instructions over one coat of industrial bituminious 85/25 grade at the rate of 1.20 Kg/Sqm over the plastered surfaces of sunken floor/wall and applying a course of a coat of binding material with blown type bitumen of grade 85/25 heating to working temperature of 180° C and applied @ 1.2 kg/sqm over bitumen felt and sunken floor shall be filled with graded cinder concrete upto top level to receive to flooring complete all as specified and directed.

bamral builder

M/S INDERPAL SINGH

Bidder Name

Sarbat Construction Co

M/S INDERPAL SINGH

bamral builder