138WE/L-40/2022-23

Amount

Dismantling of wall and ceiling boards (fibre, pulp, insulation. etc) or insulation boards/slabs/blankets, any thickness, including cover fillets all as specified and directed.

S&F of wooden panelling on vertical surface of wall using following specifications complete all as specified and directed (i) S&F Iind class hard wooden gutties of size 25mmx25mmx200mm depth fixed in wall by making holes in brick wall and making good in cement mortar 1:3 (ii) S&F horizontal rummer IInd class soft wood (kali at 120c/c of sectional area exc 13 Sqcm ans n.exc 25 Sqcm clean sawn treated with two coats of creoste oil mixed with good quality pesticide for antitermite treatment. (iii) S&F 1st classsoft wood (Deodar) boardig 12mm to 15mm thick as in wall panelling planed one side wrought and other side celan sawn and applying two coats of good quality varnish on plain surfaces over a coat of primer mixed with good quality pesticide for antitermite treatment on the other side and fixed with screws/nails on wooden runners. (iv) S&F 1st class soft wood (Deodar) decorative beading 40mm wide on top surface of wall panelling including two coats of varnish.

M&L for 7-9mm thick fine fissured teglar RH 99 Tringular and acoustic purpose of size 600x600x15mm thick fixed with dash through fastner bolt of approved quality 04 Nos for per sqm including necessary cutting securing and making good complete all as specified and directed.

S&F Plain glass panes of 3 mm thick glazing with wooden bead in squares not exe 0.5 sqm in each pane for glazed and skeleton shutter

Hacking out old broken glass ( any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads

S&F in repair Toilet Cabinet PVC with mirror and shelves (600x450) etc complete all as directed.

M&L 9mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nail/screws to timber frame work on wall

M&L 9mm thick prelaminated particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with nail/screws to timber frame work on ceiling

M&L for 6mm thick ply wood BWR type BB as in ceiling panelling fixed with nail/screws to timber frame work.

Dismantling timber scantling over 40Sqcm in scetion in any position ( frame work).

M&L for 2nd class soft wood clean sawn as in scantling fixed with nails. (timber framed and fixed)

Dismantling timber in fillets rails posts rafters purlins etc under 40Sq cm in section framed work.

M&L 2nd class soft wood clean sawn as in scantling fixed with nails exceeding 13Sqcm and n.exc 25Sq cmin section

Preparing surfaces of any description not otherwise described over 10 cm width or girth of new or previously untreated wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer

Demolition of reinforced cement concrete any description

M&L pre-cast cement concrete type B-1 (1:2:4) (using 20mm graded aggregate) as in manhole cover slabs set in cement mortar 1:6 including necessary formwork complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

Excavation in trenches n. exc 1.5m wide and n exc 1.5m deep and getting out in soft/ loose soil.

Returning, filling in excavated approved earth in to trenches around pipe etc after laying of pipes and testing complete including watering and well ramming in 25cm layers.

Removing surplus spoil to a distance not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

M&L for Cement concerete bed to drain pipes incl packing under haunching against the sides of pipes after they are laid tested in PCC 1:4: 8 type D-2 using 40 mm graded stone aggregate for bore of pipe 300 mm.

S&F 300mm dia bore (inner dia) double wall corrugated HDPE pipe (SN-8) in any length including all fitting and jointing with eastomeric rubber link and cuppler/other jointing material laid in trenches are in floors all as sfd and directed.

Demolition and breaking up drain pipes 100mm/150mm/300 dia salt glazed ware, (SWG/AC/PVC/NP) or reinforced concrete) set in cement mortar complete all as specified and directed.

Cutting in to existing man holes for connecting new drains, making good to pipes and rendering cutting out existing banching & forming branch channel in cement cocrete 1:2:4 type B-1 smooth finished and reforming benching as required for 150/200mm pipe complete all as specified and directed.

S & F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed including Dismantiling

S & F of 110 mm dia(SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed including Dismantiling

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and directed

S & F of 75 mm bore PVC (SWR) junction single 'T' equal or unequal complete all as specified and directed

S & F of 110 mm bore PVC (SWR) junction single 'T' equal or unequal complete all as specified and directed

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, in-cluding bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connect-ing union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc complete all as specified.

Taking up or down 15 mm dia steel tubing / 16mm 3 Layer PP-R Polypropylene rndom copolymer) and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm dia steel tubing /20mm 3 Layer PP-R Polypropylene rndom copolymer) and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 25 mm or 32mm dia steel tubing/16mm 3 Layer PP-R Polypropylene rndom copolymer) and connections including cleaning for refixing or removal to store complete all as specified and directed.

Supply and fixing 15 mm bore galvanised steel water tubing 'medium grade' with all fittings and fixed to walls, ceiling or laid in floors etc. complete all as specified and directed.

Supply and fixing 20 mm bore galvanised steel water tubing 'medium grade' with all fittings and fixed to walls, ceiling or laid in floors etc. complete all as specified and directed.

Supply & fixing 20mm 3 Layer PP-R Polypropylene rndom copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all fitting and fixed to walls, complete all as specified and directed.

Supply & Fixed 25mm 3 Layer PP-R Polypropylene rndom copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all fitting and fixed to walls, complete all as specified and directed.

Supply & Fixed 32mm 3 Layer PP-R Polypropylene rndom copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc with all fitting and fixed to walls, complete all as specified and directed.

S&F in repair PP-R 20mm Gate valve (brass insert) as per requirment of the site

S&F in repair PP-R 20mm Ball valve (brass insert) as per requirement of the site complete all as specified and directed.

M&L Cutting chases brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends and making good cutting exceeding 20cm girth for concealed water tubing or concealed conduit wiring, etc.complete all as specified and directed.

S&F in repair PVC 32mm dia waste pipes all as specified and directed

S&F in repair Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) of bore of pipe 15mm complete all as specified and as directed.

S&F in reapir 15mm Bib Tap standard of PTMT any colour high pressure screwed for iron pipe/PP-R pipe and fixed (minimum weight 15mm-90Gms/20mm-125Gms Complete all as specified and directed.

S&F in repair 15 mm Bib tap long body with wall flange fancy type chromium plated brass screwd for iron pipe with capstain head complete all as specified and directed

S &F in repairs health faucet, (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25meter long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

S&F Stop valves, fancy type, chromium plated with long shank and cup (Angle valve type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm as in repairs complete all as specified and as directed.

S&F in reapir 15mm dia stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (minimum weight 15mm - 90gm/20mm- 92gms complete all as specified and as directed.

S&F in repair brass Chromium plated shower rose 125mm size with or without swivel joints, including fixing to steel pipe or union as in repairs complete all as specified and directed.

S&F in repair 15mm dia Pipe screwed for iron pipe of bore of pipe Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, all as specified and as directed.

S&F in repair Grating doom 100mm dia of PTMT (minimum weight 25 Gms) complete all as specified and directed

M&L PVC connections 15mm size with PTMT nuts of length 450mm as in repairs complete all as specified and as directed.

M&L PVC connections 15mm size with PTMT nuts of length 600mm as in repairs complete all as specified and as directed.

S&F Towel Rail 600mm long of aluminium fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 270 gms) 20mm dia, D type4, as in repairs complete all as specified and as directed.

S&F in repairs PVC valve less, syphonic action type, white low level flushing cistern of capacity 10 litre with inlet ball valve float and handle including brackets and 32 mm dia PVC flush pipe complete all as specified and directed

S&F in reapir Vitreous china wash down water closet pan (pedestal pattern) white (excluding flushing cistern and flush pipe) and including fixing of the following components viz. pedestal pan with "P" or "S" trap, seat and cover for pedestal pan, flushing cistern, brackets, chain and pull or lever handle, flushing pipe including jointing to socket of flushing rim and connecting pipe to union of flushing cistern, inlet and overflow pipe, anti-syphonage pipe or stopper fixed as in repairs complete all as specified and as directed. Note:- Flushing cistern and flush pipe as required shall be measured and paid for under supply only separately.

S&F in reapir Vitreous china wash basin, white, flat back, size 550mm x 400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and including fixing of the following components viz. pillar taps, waste fittings and union, plugs and chains and connecting upto supply pipes, wastes or traps, screws, plugs, cement mortar and other subsidary materials required for fixing including cutting for and pinning in ends of brackets but exclusive of fixing of supply and waste pipe fixed as in repairs complete all as specified and as directed. Note:-(a) Pillar taps, waste fittings and waste pipes as required shall be measured and paid for under supply only separately.

S&F in repairs Vitreous china squating pan " Orissa pattern, size 580 x 440 mm white, with integral foot rest (excluding flushing cistern and flush pipe) incl P or S trap connection to trap, and to flushing pipe anti syphonoge pipe etc incl making good to floor complete all as specified and directed

Supply only Waste fittings, brass, chromium plated for glazed ware basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed of bore of pipe 32mm complete all as specified and as directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe of bore of pipe 15mm fixed all as specified and as directed.

S&F in Repair Vitreous China Urinal full stall type white (excluding flushing cistern flush pipe and wast pipe) Vitreous China Urinals bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F in reapir waste fittings, brass, chromium plated for glazed ware basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed of bore of pipe 32mm all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. capacity exc 250 ltrs n. exc 500 Ltrs and disconnecting existing tanks shifting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and refixing in position. all as specified and directed.

S&F Soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed

S&F in Repair 15mm Brass CP Mixer for Mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed

S&F Gun metal, globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed of bore of pipe 20mm as in repairs complete all as specified and as directed.

S&F in Repair Single Hole brass CP WHB Mixer cock 15mm dia complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer including balance area complete removal.

M&L for preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of primer including 2mm thick white wall care Putty on wall to obtain smooth finish etc including balance area complete removal.

M&L for preparation of old distemper surface by washing, rubbing down and stopping of distemper and painted surface and applying one coat oil bound emulsion on wall surfaces white or tinted

M&L for preparation of old painted surfaces of wood and wood based materials of any description over 10 cm width or girthnot otherwise described and applying one coat of synthetic enamel paint.

All as per Item No-77 above but on steel surfaces

M&L for complete removal of existing finishes on wall and applying two coats of Appx exterior emulsion paint on wall surfaces complete all as specified and directed

S & F drapery rod 25 mm dia with PVC pipe over MS conduit including curtain rings suitable for 25 mm dia pipe & side cups with brackets including fixing arrangements with drilling holes etc complete of approved quality and colour complete all as specified and directed.

S&F in repair Door closer, hydraulically regulated, designation No 3 universal type suitable, suitable for door shutter of 851 to 1000mm in width and of wight between 61 to 80Kg and fixed door closer, aluminium (die cast) body, all as specified and as directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass, other parts made of mild steel heavy duty and fixed as in repairs all as specified and as directed.

S&F in Repair venetion blind vertical type level or ultima 100mm width of strip with necessary pulling threads aluminium channel along with all arrangement tixed to wall completed all as specified & directed.

Demolition of brickwork or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stonework and precast concrete articles all as specified and as directed.

M&L Precast cement concrete 1:3:6 Type C1 (using 20mm graded stone aggregate ) block masonry with solid blocks exc 10cm in width and setting in CM 1:6

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below and above ground level) and removing the unserviceable materials to a distance not exceeding 100m all as specified and as directed.

M&L for treating the sunken floor with preparing surfaces by brushing with wire brushes for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc applying consisting of the following operation (a) 10mm thick plaster/screed bed in cement mortar 1:3 complete mixed with water proofing compound as per manufactiures instruction complete all as specified and directed ( Note WPC shall be measured and paid separtely) (b) cleaning floor surface by wire brush brooming & removoing dust & shall be painted with a coat of bituminous primer conforming to IS :3384-1986@ 0.3 LTR per sqm uniformily complete all as sfd & directed (c ) After primer the entire roof surfaces applying tack coat of hot blown bitumen grade 85/25 grade conforming to 702- 1988 @ 1.2 kg per sqm over primer (d) Over hot bitumen laying polymeric water proofing membrance consisting of 90 to 100 micorn thick center core of HMHDPE film with standered weight not less than 3 Kg per sqm over entire area laid with 100mm side lap/end lap on prepared surfaces as per manufacture's technical instruction & seal complete all as sfd & directed (e) Again the entire floor surface applying tack coat of hot blown bitumen graded 86/25 grade conforming to IS 702 @ 1.2 Kg per Sqm

M&L for cement concrte 1:5:10 type E2 (using 40mm graded stone agregate) as in sub base etc mixed with 5% liquid water proofing compound by weight of cement or as manufactures instruction including finishing surfaces even and smooth without using extra cement complete all as sfd

M&L 25mm thick PCC 1:2:4 type B-0 using 20mm graded stone aggregate as in leveling course to floor complete all as specified and directed

Dismantling of floor,hearth or wall tiling including cement mortar bedding but not backing and rubbish off the premises.

M&L for Non skid ceramic jointless coloured tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed with white as coloured cement to match over and including 15mm thick screed bed in cement mortor (1:6) complete all as specified and directed.

M&L for glazed ceramic colour tiles in vertical surfaces of size 300x200x7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including rendering 10 mm thick in cement mortor (1:4) on vertical surface as in backing coat all as specified and directed.

S&F powder coated for aluminium anodised window openable fixed type/sliding type weighing not less than 1.35 Kg/RM including 5mm thick glass/wire mesh fixed with rubber gasket. The aluminium member of shutter is 65x40mm along aluminium handle & tower bolt etc complete all as specified.

S&F powder coated aluminium anodized grills with 6x5mm aluminium section having square gap of 100mm thick with fixing rails of channels 12-15mm complete all as directed

S&F powder coated aluminium anodized door/partly paneled and partly glazed with 4.5mm thick plain glass sheet/wire mesh and 12mm particle board interior grade both side laminated and aluminium section weight not less than 0.55 kg/RM with self closing hydraulic door closer & floor spring etc with complete with all fitting all as specified and directed.

Taking down chowckat or frame with shutters (without taking of shutters from the frame) exe 1.5 sqm each but n. exc 4 sqm each any type of door (wooden , aluminium & Steel etc)

All as per item No. 96 above but n. exc 1.5 sqm type of window (wooden , aluminium & Steel etc)

Preparation of old decorated plastered or unplastered wall surfaces and applying one coat of white wash on wall surfaces

Preparation of old decorated plastered or unplastered wall surfaces and applying one coat of Colour wash on wall surfaces

M&L flush shutters 30mm thk, solid core construction, with block board core & plywood face panels, commercial type on both sides all as directed and specified.

M&L Plain solid straight chowkats and frames rebated and put together with glue pinned joints supplied and fixed of second soft wood

S & F Glazed and skeleton shutters rebated and prepare to receive glass gauge, etc., (with sash bars) size of members of shutters as specified in SSR part-I section 8 clause 8.20 (b) supplied and fitted to chowkats, thickness of shutters 30 mm thick of second class softwood

S&F MS flat iron as in hold fast etc and similar work.

M&L PCC 1:3:6 type C1 (20mm gr agg) as in anchoring hold fast etc bed plate etc all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with beading to wooden frames all as specified and as directed.

S&F 300mm Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy & fixed

S&F Aluminium, anodised barrel tower bolts of extruded section and fixed for 200 mm length

S&F Aluminium handles, 150mm fabricated type anodised

S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Aluminium, anodised barrel tower bolts of extruded section and fixed for 100 mm length

S&F Aluminium handles fabricated type anodised for 100 mm long

M&L 75mm thick for PCC 1:3:6 type C-1 as in plinth protection , complete all as specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in sub sub base complete all as specified and directed

M&L for 100mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in floor complete all as specified and directed

Dismantling of steel sheeting any gauge, thickness including Nainital or similar pattern roof covering (corrugated, semicorrugated , etc) sheet in roof covering all as specified and directed.

S&F 0.63mm thick galvanised mild steel sheets with two corrugation side lap fixed with J or L hooks with grade of zinc coating 275

Taking down existing unserviceable/old copper / alluminium point wiring (light,fan,socket,power point ) complete excluding fitting fixtures such as switches ,ceiling roses, pendant/angle holders regulators, sockets etc complete all as specified and directed

Material and labour for concealed point wring complete with stranded copper conductor 1100 V grade cable 1.5 sqmm FRLS with colour coding (Nominal area) PVC insulated (unsheathed) in and including PVC Cassing Capping not less than 20 mm width with sunk in pressed steel terminal boxes of required size not less than 1.6 mm thick factory made and factory painted with stove enameled black paint with top cover 3 mm thick bakelight laminated sheet with brass screws and Cup washers with all assessories including 1.5 sqmm stranded copper conductor cable PVC insulated FRLS in green colour as earth wire connected to common earth dolly complete all as specified and directed

a) All as per item no 118 here in before but for 5 Amp 3 pin socket on same board .

b) All as per item no 118 here in before but for 5 Amp 3 pin socket on independent board .

M & L for point wiring with 4 sq mm PVC insulated, unsheathed single core stranded copper conductor 1100 Volt grade in PVC capping cassing on wall /floor etc with all accessories of suitable size MS/Pressed steel terminal boxes 1.6 mm thk with bakelite sheet cover (hylum) 3mm thick /PVC Gang box for mounting switch, socket, Cup washers complete with all accessories for one 6 pin 15 Amp socket outlet point on independent board including 4 sqmm PVC insulated copper conductor in green colour common earth and connecting to earth dolly all as specified.

S&F switch piano flush button single pole one way 5 Amp, 240 Volts complete all as directed.

S & F switch socket outlet, 2 in 1,3 Pin, 5 Amp 240 volt flush type Complete all as directed.

S&F switch socket combination piano flush button single pole one way 5in 1 ,5/16 Amp, 240 Volts complete all as directed.

S & F ceiling rose, surface Bakelite three terminals including taking down old one. complete all as directed.

S & F 9W LED Bulb including taking down old one. complete all as directed.

S & F 7W LED Bulb including taking down old one. complete all as directed.

S & F 5W LED Bulb including taking down old one. complete all as directed.

S&F lamp holder PVC/ polycorbonate type with back plate suitable for batten fittings including taking down old one complete all as directed.

Supply and fix in replacement Endura Slim Pro Plus 2'x2' Aesthetically designed 2x2 LED Flat Panel which provides soft - light and glare free symmetrical illumination also for POP ceilings 36W Slim type with seperate Driver Model strato2X2Plr36Wled857mod of Make Havells or equivalent in price and quality of Crompton/Bajaj

S&F in replacement of LED single tube light fitting surface / pendent mounting complete with batten for LED tube light 20 Watt with , extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver.

Supply & Fixing in replacement of surface mounted Bulk Head fitting Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs 10 Watt Model: HeXaft10Wled857ssYmBoPC Make - Havells or equivalent in Price and quality of Crompton/Bajaj

Supply and replacement of exhuast fan any type and size with Plastic body 300 mm sweep including taking down the existing exhuast fan and making necessary arrangements for fixing of plastic body 300 mm sweep and connectioning with flexible three core cable from the ceiling rose complete all as directed by the Engineer-in-charge.

Supply and fix in replacement of 1100 V grade heavy duty cable PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed flat of stranded multistranded conductor size 10 sq mm 02 core, complete all as specified and directed by Engr-in-Charge.

Supply & fixing MCCB 200 Amps 36 KA, 4 Pole complete all as specified and directed by Engr-in-Charge.

Supply & fixing MCCB 400 Amps, 36 KA, 4 pole 415 V as per existing complete all as specified and directed.

Supply, fixing, connecting and testing street light LED type suitable for working on 230 volts, 50 Hz, AC of 60 Watts complete all as specified.

Supply and replacement of plug top, 3 pin, 15 amp earth metal clad (ISI marked) as directed complete all as directed.

M&L checking, Inspection, maintanance and servicing complete including replacement of unserviceable spare parts of the DG set (comparising of Engine/ Alternator/ Control panel) of the following capacity for smoth functioning complete all as per manufacturers instructions and all as directed by Engg - In - Charge A. (a) Checking of lubricating oil condition (b) Checking engine for oil, water leakage and correcting the same (c) Checking of all the nut bolts of engine and alternator (d) Checking of all belts and adjust the tenson properly (e) Cleaning of air filters (f) Checking and readjusting the valve clearance (g) Change of Oil/Fuel filters and engine oil if necessary (h) Checking of starter motor battery and charger (i) Checking of cooling system and fuel system (j) checking of all power cables and AVR connections and mounting bolt tightnees of alternator (k) checking the function of AVR genaral checks (l) Checking of control panel meters and gadgets functiong (m) Checking of all control and safety wirings B. (a) Checking of flexible coupling of engine and alternator (b) Cleaning of crank case ventilation pipe (c) Checking of injectors and fuel pump (d) Checking of alternator and carbon brushes of following cap DG sets NOTE (1) Cost of Spares required will be paid and measured separately (2) Servicing/routine check up carried out through authorised service centre of manufacturer (3) Make of spare recommendation by auth service centre of manufacturer. (a) 180 KVA DG Set

M & L for changing /toping up of best quality of engine oil 20W40 type for various type/capacity DG sets including removing of old burnt engine oil from DG Sets complete all as specified and directed . Make:-castrol/veedol/valoline

Replacement of Oil filter element as per existing for following capacity DG Sets make Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. Make- Kirloskar/Mico/TVS. (a) 180 KVA DG Set

Replacement of Air cleaner element (inner and outer) suitable for following capacity DG Sets make Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Replacement of Fuel filter elements(primary & secoundery) for following capacity DG Sets make Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Replacement of fuel pipe with banjo bolt at both side suitable for following capacity DG sets make: Kirloskar/Cummins/Greavescomplete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Repair and replacement of Dynamo Assy for following capacity DG Set Make Kirlosker/ cummins/Greavescomplete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

S&F replacement of automatic voltage regulator(AVR) 24 volt suitable for following capacity of DG Set. Cat Part No F680902000 Make -Kirloskar. (a) 180 KVA DG Set

Supply and replacement of self starter for following capacity DG Set Make Kirlosker/ cummins/Greavescomplete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Replacement of water pump assembly for following capacity DG sets make : Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Replacement of 'V' belt for water pump suitable for following capacity DG Sets make Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Replacement of Fan Hub assembely for following capacity DG set make cummins/Kirloskar/Greaves complete all as specified and directed by Engr-in-Charge. (b) 380 KVA DG Set

Supply and Replacement of lub oil pump suitable for following Capacity DG Sets,make :Kirloskar/Cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Supply and Replacement of thermostate valve suitable for following Capacity DG Sets make Kirlosker/ cummins/Greaves complete all as specified and directed by Engr-in-Charge. (a) 180 KVA DG Set

Supply and fix in Replacement Battery 12 Volt 180 AH (Maint free heavy duty with initial charging, all as specified and directed by Engr-in-Charge

M &L for Removing the fuel injection pump (FIP) & injectors from following capacity of DG sets and carry out servicing and calibration including replacement of injectors nozzles, etc. and refitting the same for smooth and efficient functioning all as directed by Engr-in-Charge. Note :-Repairs will be carried out from authorised workshop of MICO or manufacturer of DG set. (c) 180 KVA DG Set

Material and labour for replacement of battery charger 12 Volt,10 Amp and making all electrical connection testing complete all as directed

Supply and fixing Offload Change over Switch- AC 21 (side handle) in sheet enclosure, 415V AC, 50 Hz, of capacity 200 AMP, TPN complete all as specified and directed by Engr-in-Charge.

Supply and fixing Offload Change over Switch- AC 21 (side handle) in sheet enclosure, 415V AC, 50 Hz, of capacity 320 AMP, TPN complete all as specified and directed by Engr-in-Charge.

Supply and fixing of Digital RPM meter with Hour meter for any capacity of DG Set

Supply and fixing Digital Ammeter (0-800 Amp) capacity

Supply and fixing Digital Voltmeter (0-500 Volt) capacity

Supply and fixing Stainless steel, Grey colour anti-vibration support pads for isolating the DG Set engine and alternator from the mounting frame having weighing capacity upto 400 Kgs each for suitable capacity of DG set complete all as specified and directed by Engr-in-Charge.

Repair /servicing self Starter by S&F including taking out following parts (A) Field Coil (B) Armature Windding (c) Bush (d) Solenoid Switch/(Gear) for following capacity of DG Sets. (b) 180 KVA DG Set

Supply and fixing of Air pipe (Turbo to Radiator) for any capacity of DG Set

Supply and fixing of bty charging alternator (12 volt) with 2 wire system for any capacity of DG Set

Supply and Replacement of battry terminal for DG Sets complete all as specified and directed by Engr-in-Charge.

Supply and fixing battery cable assy. with copper conductor multistranded RED and BLACK colour 2mtr long 21sqmm for connection to self starter unit to Battery unit complete.

Supply & toping up of best quality anti freezing,Inhabitor Corrosion (Coolant ) liquid for DG set at varrious capacity and locations complete all as specified and directed. Make-castrol/veedol/valoline

M&L for Fixing of garden light, CONE - IP65 LED 25 W , Cone series type as a replacement Clear, Milky diffuser die cast pole mounting Make HPL LLEDPCR25W

Supply and replacement of Change over switch 415 Volt in sheet metal inclosure 4 Pole of capacity 400 Amps with connecting acessories complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered wall surface and applyin one coat of cement base paint on wall surface.

R B TRADERS

M/S MUNEER HASSAN AKHON

Rampal Singh Contractor