GMC CSIR MBSA - CIVIL

Amount

SUBHEAD - A

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc. and removal of form for:removal of form for: Shelves (Cast in situ)

Centring and shuttering including strutting, propping etc. and removal of form for:removal of form for: Edges of slabs and breaks in floor and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-mechanically Treated bars

Brick work with common burnt clay F.P.S. bricks (non-modular) of class designation 75 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. bricks (non-modular) of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above floor V level for each four floors or part thereof by mechnical means by lifting material using mobile crane.

Half brick masonry with common burnt clay F.P.S. bricks (non-modular) of class designation 75 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 Cement : 4 coarse sand)

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means by lifting material using mobile crane.

Providing and fixing 18mm thick gang saw cut mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Rajnagar plain white marble / Udaipur green marble /Zebra black marble. Area of slab over 0.5 sqm

Providing and fixing 18mm thick gang saw cut mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.5 sqm

Providing edge moulding to 18mm thick marble stone counters,Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Marble work

Extra for fixing marble / granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc .including rubbing and polishing of cut edges.

Floor polishing on masonry or concrete floors with wax polish of approved brand and manufacture after entire cleaning of floor.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Sal wood

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202(Part I). On one side only

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing 19 mm thick commercial board for making storage cabinet, almirah or providing shelve/partition etc wherever required including fixing wooden margins on exposed edges with necessary screws,adhesive etc as per direction of Engineer InCharge.

Providing & Fixing 6mm thick commercial plywood in pannelling, partitions,almirahs etc with nails, adhesives etc complete

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality. 1.0 mm thick.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : Kiln seasoned and chemically treated hollock wood. 50x12 mm

Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with wooden adhesive of approved quality and screws/ nails on the edges of the Pre-laminated particle board as per direction of Engineer-in-charge.

Providing and fixing drawer upto 15 cm depth in the cupboard with 12mm thick ply in base and sides including necessary handles/knobs and 20x25mm wooden runners fixed with screws complete including complete painting. NOTE : Overall plan area of the drawer shall be measured:

Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842, including top cover of 6 mm coir veneer board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc. all complete.

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia. (heavy type)

Providing and fixing Bamboo jaffery/ fencing consisting of superior quality 25 mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-charge.

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc., complete. Overall width 35mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door wt up to 36 to 80 kg and door width from 701mm to 1000mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing Mortice lock with handles complete set including necessary screws etc. complete (Godrej Model no. NEH 06 1CK 20cm Zinc Alloy or equivalent)

Providing and fixing chromium plated brass handles with necessary screws etc. complete:100 mm

Providing and fixing aluminium sheet on existing door shutters (bathroom and W.C. doors) using adhesive/nails etc.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing 30mm thick factory made PVC flush door shutter consisting of panel of Hollow PVC Profile of 24mm thickness, consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm inserted inside the hollow section of styles, top and bottom rails and two 19mm x 19mm M.S.tubes inserted horizontal inside the hollow profile section at an equal distance from top and bottom of door and fixed with hollow profile section using 3mm thick Plain PVC sheet using screws. Hollow PVC profile shall be llipped with 10mm (5mm x 2) thick x 24mm width on styles and rails using solvent cement. The inner panels shall be laminated with 5mm thick termite proof, water proof and fire retardant plain PVC sheet using solvent cement on both the sides of the panel etc. complete as per the direction of Engineer in charge, manufacturer's specification and drawing.

Providing and fixing 18mm thick Celuka PVC Ply, wherever required in kitchen cabinets/cubboards for PVC shelf/partition/shutters of required size and also for supports of Shelf/partition etc. The front side of all the edges visible in the shelf/partition etc are to be lipped by 18mm wide and 1mm thick PVC sheet using solvent cement etc. complete as per direction of Engineer-in-charge and manufacturer's specifications. (Piano hinges for shutters will be paid for seperately)

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube.

Removing carefully and refixing of Steel glazed/wire mesh window shutters after repairing, welding, grinding and adjusting in position including provision of MS hinges/friction hinges etc. as required to complete the job in all respect for smooth and effort less functioning of steel glazed window shutters.

Repairing of Steel glazed/wire mesh door shutters by providing strip of MS sheet at bottom style/ cut-piece of M.S flat etc as required including misc. welding work, grinding and adjustening of door shutter in position for smooth and effort less functioning of steel glazed doors.

Creating opening for provision of air conditioner in M.S. glazed windows/ventilators by cutting the window's main frames and grill & re-adjusting the main frame members as per the requirement/A.C size by welding work & grinding work for making the modified M.S glazing smooth. Work also includes providing & fixing M.S. frame of appropriate section in the final A.C. opening created as per above, so that window glass pane may also be fixed over it, in case air conditioner is removed.

Extra for creating Air conditioner opening as per above, but at junction of angular M.S.glazed window/ventilator.

Repair of jammed window or door shutter by grinding /welding work for its smooth functioning.

Welding M.S. hinge/handle/stopper etc on M.S.door shutter (cost of hinge/ handle/stopper to be included)

Providing & fixing galvanised M.S. wire gauge of Average width of Aperture 1.4 mm both sides with wire of dia 0.63 mm for doors,windows and ventilators at all heights, fixed with steel ribets or by welding etc including removing the existing old wire mesh complete as per the direction of EIC.

Providing, welding and fitting godown lock heavy-type on M.S. wire mesh entry/exit door shutter including dismantling of existing unfunctional godown lock.

40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1mm to 4mm nominal size laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume including cement slurry etc. complete :Ordinary cement without any pigment.

Extra for laying terrazo flooring on staircase treads not exceeding 30 cm in width including cost of forming, nosing etc.

Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1 : 4 ( 1 cement : 4 coarse sand) : 25 mm thick

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622 , of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints. Size of tile 600 x 600 mm

Providing and fixing Ist quality digital rectified ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality digital rectified ceramic glazed tiles/vitrified tiles for repairing work or piece work in toilets/kitchens/ wash areas/rooms etc. including dismantling of backing existing plaster in any required quantity ( for qty upto 0.50 sqm or less) conforming to IS : 15622 of thickness as per manufacturer's specification, matching to existing laid tiles of approved make in all colours, shades except begundy, bottle green, black of any size(30x30 to 60x60cm) as approved by Engineer-in-Charge in floor/skirting/and dados over 12 mm thick bed of Cement Mortar 1:3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified digital glazed ceramic floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing on wall face un plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. 75mm diameter

Providing and fixing on wall face un plasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Bend 87.5 75 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Reducer 110 mm X 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.Single tee with door 110x110x110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Bend 87.5 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Cowl 110mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

12 mm cement plaster of mix : 1:6 (1 cement : 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement : 6 coarse sand)

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 mtr. lead. With cement mortar 1:4(1cement :4 coarse sand)

Rough cast plaster upto 10m height above ground level with a mixture of sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over and including the fresh plaster in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 Coarse sand) coarse sand) and top layer 10mm cement plaster 1:3 (1 cement : 3 fine sand) mixed with 10% finely grounded hydrated lime by volume of cement.Ordinary cement finish using ordinary cement

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1mm , of approved brand and manufacturer, over the plastered wall surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including priming coat with cement primer

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade . Old work (one or more coats)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade: one or more coat on old work

Applying priming coat :With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work

French spirit polishing :One or more coats on old work

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives (Apex ultima or equivalent) of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including base coat of exterior wall primer @ 0.83 ltr/ 10 sqm). Note: Actual consumption may vary as per manufacturer's specification.

Re-lettering with black Japan paint of approved brand and manufacture.

Renewing glass panes, with putty and nails wherever necessary: Float glass panes of thickness 4 mm

Renewal of old putty of glass panes (length)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc.complete as per directions and approval of Engineerin-charge. The elevational area of the scaffolding shall be measured for payment purpose.The payment will be made once irrespective of duration of scaffolding.

Demolishing cement concrete including disposal of material within 50 metres lead as per direction of engineer in charge. 1:3:6 or richer mix

Demolishing R.C.C. work including stacking of steel bars and disposal of unserviceable material within 50 metres lead:

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: Of area 3 sq. metres and below

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: Of area 3 sq. metres and below

Dismantling tile work in floors,walls and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles upto10 mm. (Entire backing mortar/plaster to be removed i/c making good the base/brick surface, if got damaged)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling G.I. pipes (external work / internal concealed) including excavation and refilling trenches after taking out the pipes, including stacking of pipes within 50 metres lead :15 mm to 40 mm nominal bore

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, including stacking of pipes within 50 metres lead :Above 40 mm nominal bore

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes, lead at site within 50 metre lead: Upto 150 mm diameter

Dismantling of flushing cistern/washbasin/WC/sink etc. of all types (C.I./PVC/Vitrious China) of any size including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction and of approved size and design/ shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with coarse sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan ( Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, Parryware/Hindware/Cera. White Vitreous china Orissa pattern W.C. pan.of size 580x440mm with integral type foot rests

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P.brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall. Size 450x300x150mm

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P.brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall. Size 600x450x200mm

Providing and fixing white vitreous china pedestal type (European type/wash down type) water closet pan.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings and fixtures complete. 10 litre capacity - White

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white

Providing and fixing PVC fittings complete for the PVC cistern of superflow or parryware make.

Providing and fixing PVC cistern fittings complete for dual flushing 2-in-1 cisterns resting on wall hung EWC. (parryware or superflow)

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan. White solid plastic seat with lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings: Flat back wash basin of size 550x400mm.

Providing and fixing under counter oval shaped coloured vitreous china wash basin of size 550x400mm with C.I/M.S brackets, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms

P/f 32mm CP brass waste of standard pattern in wash basins/sinks.

P/f 50mm CP brass waste of standard pattern in wash basins/sinks.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32mm dia.

Providing and fixing 100mm sand cast Iron grating for gully, floor or Nahani trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (appx. size 1.2m x 0.90 m) and of required shape and size with approved polished wooden moulding frame and 6 mm thick hard board backing :

Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe

Providing and fixing soil, waste and vent pipes : 75 mm dia. Sand cast iron S&S pipe

Providing and fixing plain bend of required degree. 100 mm. Sand cast iron S&S

Providing and fixing plain bend of required degree. 75 mm. Sand cast iron S&S

Providing and fixing single equal plain junction(with door) of required degree.100x100x100mm. Sand cast iron S&S

Providing and fixing single equal plain junction (with door) of required degree. 75x75x75mm. Sand cast iron S&S

Providing and fixing terminal guard: 100mm. Sand cast iron S & S as per IS - 1729

Providing and fixing terminal guard: 75mm. Sand cast iron S & S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet. Sand Cast Iron S&S

Providng and fixing CP brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arangement of approved quality colour and make. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less thant 390gms.

Providing and fixing PTMT Shelf 440 mm long, 124 mm width and 36 mm height of approved quality, colour and make, weighing not less than 300gms (Prayag or equivalent) .

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes as per BIS specification,weighing not less than 60gms (Prayag or equivalent)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 40 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 50 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. (internal work). Concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall. 15 mm dia nominal bore

Making connection of G.I./CPVC distribution branch with G.I./CPVC main of following sizes by providing and fixing tee, union etc including cutting and threading the pipe or with adhesive etc. complete :25 to 40 mm nominal bore

Replacement of tank nipple G.I/CPVC of size 20/25 mm dia. in water storage tank.

Replacement of tank nipple G.I/CPVC of size 32/40/50 mm dia. in water storage tank.

Fitting of broken G.I/CPVC water supply line of size 15/20/25 mm dia. by providing and fixing necessary nipples/sockets/unions etc as required in the broken water suppy line for its rectification.

Fitting of broken G.I/CPVC water supply line of size 32/40/50 mm dia. by providing and fixing necessary nipples/sockets/unions etc as required in the broken water suppy line for its rectification.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) with provision of union & nipples in the existing line near gate valve. 50 mm nominal bore. Make Leader (ISI) or equivalent

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) with provision of union & nipples in the existing line near gate valve. 40 mm nominal bore. Make Leader (ISI) or equivalent

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end ) with provision of union & nipples in the existing line near gate valve. 32 mm nominal bore. Make Leader (ISI) or equivalent

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 20mm nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 15mm nominal bore.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work). 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work). 20 mm nominal bore

Providing & fixing CP brass bib cock of approved quality conforming to IS: 8931. 15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. a) 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

Providing and fixing swan neck C.P. brass close hole basin mixer of approved quality and make, weighing not less than 1.970 kg. a) 15 mm nominal bore of standard back type

Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40gms.

Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks

Providing & fixing CP brass extension nipple for fitting of bibcocks, angle valves etc.

Supplying and fixing of CP brass cap for bath fittings of approved quality ( heavy duty)

Providing and fixing CP brass grating of approved quality and colour (heavy duty).Cicular type 100mm NB

Grouting of sunken area floor trap in toilet/kitchen with neat cement punning after proper cleaning to make it leakage proof and water tight.

Providing and applying M-seal on joint of C.I/G.I pipes/PVC tanks etc. for arresting the leakages.

Providing and placing on terrace of multistoried building upto floor 9 level, polyethylene water storage tank as per ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Make Sintex or equivalent

Providing and fixing in position rectangular C.I cover with frame for man-holes. The weight of cover and frame to be not less than 23 kg and 15kg respectively.

Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5kg.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Supply of jhulla for cutting trees in shafts, repairs of the pipes and other repairs works upto the height of 25 meters including 04 labours for holding jhulla with all the safety measures and tools as directed by Engineer -In -Charge.

Disposal of Building rubbish / malba / similar unserviceable, dismantled or waste material by mechnical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer in Charge, beyond 50 mtr initial leads, for all leads including all lifts involved.

SUBHEAD - B

PVC (steel wire) connection pipe with brass unions. 45 cm length : 15 mm nominal bore

Heavy-type brass face (for repair of bib-cocks, concealed, angle valves etc.)

Washer (upto 8mm thickness) - for repair of bibcocks/anglevalves/ mixers/concealed etc)

Washer (for repair of Ball cock/syphon of flushing cistern of WC).

PTMT Ball cock with Epoxy coated aluminium rod & L.P./ H.P.H.D.plastic ball.15 mm nominal bore, 105 mm long, weighing not less than 138 gms

Flushing Cistern handle (Superflow/parryware).

Lid (cover) of polyethylene water storage tank as per ISI : 12701 with suitable locking arrangement. For tanks upto 20,000 litre capacity. Make Sintex or equivalent.

M.S.oxidised casement stays (straight peg type) with necessary screws etc. complete.300 mm weighing not less than 200 gms.

M.S. oxidized handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete (best make of approved quality) : 50 mm

50 mm cup board or wardrobe knob with nuts complete.

Aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc.

Aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. Twin rubber stopper

Aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc.: 300x16 mm (Heavy)

Aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc.: 250x10 mm

Aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.:125 mm

Magnetic catcher in cupboard / ward robe shutters including fixing with necessary screws etc.(Best make of approved quality. Double strip (horizontal type)

Plastic letter boxes made of injection moulded ABS plastic,ultraviolet stablised colour, water proof, inbuilt lock system ,rust and termite proof of 305x260x95mm size complete in all respect fitted as per the direction of Engineer in charge.

SUBHEAD - C

Routine general and preventive maintenance works to be carried out through manpower deployed at site for various misc. day to day jobs as mentioned in Annexure - I

SUBHEAD - D

Buy back of dismantled kitchen, toilet flush door shutters including all the fittings i.e. tower bolts , sliding door bolt etc.and taking the same out of campus .- Of area less than 3.0 sqm.

Buy back of old M.S. door frames upto 2 sqm obtained after dismainting works etc.

Buy back of old M.S. windows with frames upto 1.0 sqm, obtained after dismainting works etc.

Buy back of old corroded railing pipes of 50mm dia NB as received at site after dismantling works.

Buy back of old corroded railing pipes of 25mm dia NB as received at site after dismantling works.

Buy back of old M.S. curtain rods 20mm dia. as received after dismantling works.

Buy back of old broken M.S. wire mesh received during its replacement with new one.

Buy back of unfunctional godown lock and taking that out of campus.

Buy back of GI pipe with fittings, obtained from dismanting work and taking that out of campus. 15 mm to 25 nominal bore dia.

Buy back of GI pipes with fittings, obtained from dismantling work and taking that out of campus. 32 mm to 65 nominal bore dia.

Buy back of CI pipes with fittings otained from dismantling work and taking that out of campus .

Buy back of dismantled old C.P/PTMT towel rail 600 mm long and taking them out of campus.

Buy back of dismantled old PTMT shelf 440 mm long and taking them out of campus.

Buy back of old broken plastic seat covers of EWCs obtained during replacement with newones.

Buy back CP brass sanitary fittings such as short /long body bib cocks, concealed stop-cock, angle valve, basin mixer etc. dismantled from toilets and kitchens. 15 mm nominal bore

Buy back of old swivelling shower rose and taking that out of campus

Buy back of old existing PVC connection pipes 45 cm long

Buy back of old dismantled brass face obtained from bib-cocks, angle valves, concealed, mixers etc.

Buy back of cistern internal old dismantled fittings complete

Buy back of cistern old dismantled ball cock 15mm.

Buy back of dismantled flexible waste pipe of wash basin/sink.

Buy back of dismantled gun metal gate valve with C.I. wheel of size 50 mm nominal bore.

Buy back of dismantled gun metal gate valve with C.I. wheel of size 40 mm nominal bore.

Buy back of dismantled gun metal gate valve with C.I. wheel of size 32 mm nominal bore.

Buy back of dismantled ball valve (brass) with plastic floats of size 25mm nominal bore.

Buy back of dismantled ball valve (brass) with plastic floats of size 20mm nominal bore.

Buy back of dismantled ball valve (brass) with plastic floats of size 15mm nominal bore.

Buy back of old/broken polyethylene water storage obtained after its replacement with newone from terrace of multistoried building upto floor 9 level, after dismantling the tank's existing connections etc.

Buy back of old broken lid/cover of polyethylene water storage tank obtained after its replacement with newone from terrace of multistoried building upto floor 9 level.

Buy back of broken Plastic letter boxes of 305x260x95mm size complete in all respect fitted as per the direction of Engineer in charge.

Buy back of old corroded/twisted iron drain jallies covers-main gate etc.

Buy-back of broken C.I cover with frame of size 600mm x 450mm

deepa engg co

SWAGATAMA ENTERPRISES