SPL REPAIRS TO BLDG NO. 3/2 HUDSON LINE , BLDG NO P-33 AND P-34 (06 NOS QTR) AT ARJUNGANJ ALONGWITH EXTERNAL SURFACE OF BLDG NO. P-84(MAIN BLOCK) AT HQ CENTRAL COMD UNDER GE(EAST) LUCKNOW.

BOQ ITEM NO. 01 TO 22 COMMON FOR JOBS Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete .

M&L for brick work with old size fly ash bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete, all as specified.

Ditto all as above but except bricks ( bricks recovered from demolition to be used)

M&L for Plastering by using ready mix mixture of thickness 15 mm thick with water proofing liquid and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge.

Repair to plaster by using readymix mixture of thickness 10 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge

Repair to plaster by using readymix mixture of thickness 7 mm and taking down cement or cement lime plaster, raking out joints and preparing plastering the Celing surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-in-Charge

Preparation of plastered surfaces and applying two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, over a coat of 2mm thick putty and primer of required shade and colour complete, as per manufacturer's specification over Complete all as specified and directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area exc 1.5 Sqm but n.exc 4 sqm each all as specified.

Taking down chowkhat or frame with shutter (without taking off shutter from the frame) and area n.exc 1.5 Sqm each all as specified.

S&F 65x100 mm single rebated factory made 100% solid WPC (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum all as specified and directed.

S&F 65x125 mm double rebated factory made 100% solid WPC prelem both side (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum all as specified and directed.

S&F PVC connection of 15 mm bore 600 mm long with brass coupling on both ends of superior quality all as specified.PTMT nuts fixed as in repair.

S&F framed work as in doors, gates or grill of angle or other section with gussset plates, rails, braces etc complete drilled for fixing steel sheetings or other coverings. Doors etc to be prepared for hanging or sliding with and including either hooks or hinges steel hanging door fittings ( exclusive of steel sheeting or other coverings running rails and guides) and hanging also fastening and fixing complete quality conforming to Fe-290W (Gde E-165) quality B complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of red oxide/zinc chrome primer complete all as specified.

S&F kitchen sink with drainage board made of stainless steel 1mm for kitchen with plugs, washers and wastes, including fixing with cast iron cantilever brakkets, bedding in cement mortar on to dwarf wall, conntecting union to pipe, overall mimimum size 915mmx460mm with bowl size 410mmx330mmx160mm including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waster fitting with long screwed shanks and fly nuts, flage end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B0, complete including taking down old unserviceable sink.

Supply only Liquid water proofing compound complete all as spesified and directed.

S&F 15 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down

S&F 20 mm bore GI tubing medium grade with all fittings and fixed complete to wall and ceiling or laid in floors including taking down

Dismantling wrought iron or mild steel work of any description not otherwise provided

S&F in repair 10 Litres capacity PVC valveless syphonic action type flushing cistern low level, white with inlet ball valve float and handle including brackets connection to pipes and fixing of lever if any joint between flushing pipe and socket of WC pan pre-made

BOQ Item No. 23 to 103 for Job No. LSA/DWP/27/SRW/2025-26 M & L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 to any radius complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls, etc any description .

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or mechanical means, including filling depression of scrapped surfaces with putty and and applying two coats of oil bound distemper complete all as specified and as directed.

M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) Applying a coat of fibre reinforced PU primer confirming to ASTM D412 @ 30% water dilution on prepared surfaces and allow to dry. (b) Supply and Applying 2 coats of Hybrid PU based elastomeric single component coating over primer surface @ 10kg /10.76 Sqm total comsumption having below properties:- 1. Elongation - 500%-600% 2. Solid contents - 80%, 3.Tensile Strength - 1.6N/mm2 4. Adhesion to concrete - 2.2N/mm2 5. Initial hardness shore strength - 60Min. 6. Tear Strength - 14Mpa. 7. Total thickness of layer shall be 1.2 - 1.5mm. Note : The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates.

Demolition of concrete of any Description and in any position not otherwise specifically provided for cement concrete reinforced including roof padding, complete all as specified and directed.

M&L PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof kerbs/padding /benching or mud stops, and platform for mounting service tanks, rounded,chamfered on edges including necessary use and waste of from work etc all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, and 4 no. stainless steel butt hinges all as per direction of Engineer-In- Charge.

Supply and Fixed Providing 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER with lamination consisting of Density 650 Kg /Cum Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.complete all as specified and directed by Engr -In - Charge. approved by Engr -in -charge.

S & f powder coated aluminum ventilator ( louvers) shutter with 3.8 mm thick plain / tinted glass consisting of frame of size 63.5 x 44 and shutter sections weighing not less than 0.55 kg/m with locking arrangement as approved fixed including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings with stainless steel wiremesh of 0.36mm including necessary fixing arrangement complete all as specified and directed

S&F powder coated(min thickness of powder coating 50 micron) anodised aluminum window shutter three track sliding type, section having frame size bottom with outer 92x45.5x1.5mm (section code 20617) , top and side 92x31.75x1.5 (section code 20831) & aluminum section of shutter top and bottom size 40 x 18 x 1.5 ( section code 20736) , interlock size 40 x 18x 1.45 (section code 20737), side/ middle size 40 x18 x1.55, (section code 20738) including necessary joining cleats, glazing clips rubber backing, anodised aluminum snap beading screw, anodised aluminum fitting complete as per site requirtement glazing by using 5mm thick plain sheet glass and ss wiremess of dia 0.36mm and aperture 1.4mm thick all as specified and directed. Ref drg no celz/c-td/151 sheet no 1/1 & 2/2 . Note- 1. Glazed shutter glass thickness not less than 5mm and ss wiremess shutter with ss wiremesh as approved by GE is also included. No payment will be made separately. 2. No extra payment will be made for section profiles of higher sizes.

S&F in repair 'E' board everest make 600x600x4mm thick white prelaminated sett embosed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be poweder coated white. The frame work shall comprise of main runner made from 0.33 mm thick GS sheet and of size 24x32x300mm abd soaced at 1200mm centers securely fixed to be structural soffts by approved hangers at 1200 mm maximum centrers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug level and justers and screws etc. The last hanger at the end of each main runner shall not be grater than 450mm from adjacent wall, Flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm center to from 1200x600mm modules cross tee longer than 600mm to be supported independtly. 600x600mm dodules to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee, perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture insturction.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismatling of exisitng tank float including ball valve 20 mm bore high presure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight not less than 210 grams) complete all as directed

S&F 300 mm long MS ordinary pattern door spring "plate type" including roller and roller plate complete all specified and directed.

S&F in repair 25mm dia stainless steel curtain rod, superior quality (weight not less than 300 g/RM) with end brackets and end knobs and fixed to wall with wooden plug/ PVC gully with CP screws and cup washers complete all as specified and directed.

S&F in repair vitreous china Wash hand basin, white, flat back type of size 550x400mm including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10X7.5X15cm, 32mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.(excluding tap, waste chain & plug) complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern) white includig fiximg bolts, seat cover and flush pipe 'P' and 'S' trap, including connection to trap and flushing pipe , antisyphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor complete all as specified and directed.

M&L for premium quality joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 and dismantling of existing tiles complete all as specified and directed.

M&L for joint free glazed coloured GLOSSY tiles, superior quality of size 300 x 450 x 7mm thick/300 x 600 x 7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 and dismantling of existing tiles complete all as specified and directed.

M&F for vitrified Ceramic tiles dark shade 8-10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile over screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:6 as specified and directed by Engr-in-Charge.

M&L Granite 18- 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM 1:4 including moulding (rounding edges) and drilling hole in granite stone for inserting pipe ,dismantling of existing stone slabs etc complete all as directed.

M&L for Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

S&F two(double) legged floor door stopper of aluminum body & tougues with hard drawer steel spring fixed in floor of 100mm complete all as specified and directed..

S & F factory made WPC single extruded 100% lead free ISO certified board of 18mm thick bothside pre laminated shutter for KITCHEN cupboard, Room Cupboard and bathroom cupboard. The laminated shutter should be .12-.14 microne pre laminated side with laminated color and other side same laminated color of density not less than 650 kg / cum manufactured by an ISO 9001:2015 certified company. All the edges shall be covered with 2 mm thick edge moulding tape or 90 degree edge bend finish. The 18mm board should be 100% lead free, water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified.

S & F Stainless Steel handle matte finish fabricated type 150mm long as directed.

S & F Continuous (piano) hinges of size of flap 30mm mild steel, bright finish or elecrogalvanised fixed with screw to timber frame work complete all as specified and directed

S & F Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate for cup board / cabinet shutters complete all as specified and directed

S&F Aluminium anodised barrel tower bolts of extruded section 200mm long complete,

S & F Stainless steel Butt hinges "medium weight" steel 100mm size as directed.

M&L for 300mm aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts fixed.

S&F in repair chromium plated box type toilet paper holder fancy all as specified. make; Plumber/jaquar or equivalent.

S & F in repair for CP bib taps 15mm fancy type long body Chromium Plated cast copper alloy with crutch or butterfly handle complete all as specified.

S & F in repairs 15mm bore, fancy type shower rose,125 mm size chromium plated complete all as specified and directed.

S & F in repairs brass CP wall mixer for mixing hot & cold water with provision for over head shower with arm and long bend pipe and wall flanged screwed down for iron pipe of 15 mm bore size complete all as specified and directed.

S & F in repairs brass CP central hole Basin mixer fixed to pipe of 15 mm bore size complete all as specified and directed.

S & F in repairs brass CP kitchen sink mixer for mixing hot & cold water with provision for over head shower with arm and long bend pipe and wall flanged screwed down for iron pipe of 15 mm bore size complete all as specified and directed.

S&F in repair Pillar taps 15mm bore, half/quarter turn, fancy type, long body, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe including all accessories complete all as specified and directed.

S & F in repair Angle valve cast copper alloy with capstan head chromium plated screwed down high pressure with long shanks and fly nuts screwed for 15mm bore pipe complete as specified.

S&F in repair CP soap dish, superior quality, fixed to plugs with chromium plated (CP) brass screws complete, all as specified and directed.

S & F in repair Gun-metal, globe or gate valves 20mm with iron wheel head, screwed both ends for iron pipe all as specified

S&F long body 15mm bore two-way bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S & F in repairs Tubular Towel Rail 20mm dia. 'D' type, 600mm long of CP fixed with and including Chromimum plated brass screws and wooden/plastic cleats.

S&F CP Towel ring 200mm dia superior quality fixed all as approved.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 550 mm long complete all as specified and directed.

S & F in repair glass corner shelves fancy type 6mm thick 250x250mm size and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

S & F in repair hand shower ( health faucet) with 1mtr flexible tube with wall hook bracket etc complete set of superior quality all as specified and directed by Engineer-in-charge. Make: Parryware or equivalent.

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long ,including demolition of cement concrete (unreinforced) in ground floor and paving n exc 15cm thicknes and below or above ground level complete all as specified and directed

M & L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base etc.including demolition of Cement concrete (unreinforcde) in ground floor and paving n exc 15cm thicknes and below or above ground level complete all as specified and directed

M & L Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in with grey cement & no pigments over Screed bed or bedding layer of mortar 15 mm thick in Cement mortar 1: 4 for laying floor finishes complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Demolition and breaking up drain pipes ( Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 100mm/75mm bore.

S & F PVC (SWR) 110 mm size pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all specified and directed.

S & F PVC (SWR) 110 mm size pipes single socketed, in any length with rubber ring joints,including stack clamps fixed to walls complete all specified and directed.

S & F PVC (SWR) 75 mm size pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all specified and directed.

S&F in PVC (SWR) 110 mm bends, any radius complete all specified and directed

S&F 75mm bore PVC (SWR) bend, any radius complete all specified and directed

S&F in PVC (SWR) 110 mm Tee, equal or unequal complete all specified and directed

S&F 75mm bore PVC (SWR) Tee, equal or unequal complete all specified and directed

M&L PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement

S&F PVC(SWR) 75 mm bore floor trap plan with grating including jointing with solvant cement complete all as specified & as directed.

S&F 110mm bore PVC (SWR) vent cowl, complete all as specified and directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Panel with wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified

S&F for stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples all as specified.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in Chhajjas, cover slab, shelves and similar articles set in CM 1:6 complete all as specified and directed. Note:- Reinforcement shall be measured & paid separately

Demolition of cement concrete(reinforced) such as beam, roof, beams, shelves, manhole cover chajjas and similar suspended work complete all as specified.

Mild steel TMT bars 06 to 08 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work n.exc 200mm thick

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. of Fe-410-W(GdeE-250) quality B to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete

S&F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws all as specified.

S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws all as specified.

Supply only Chain link MS galvanisd fencing, any size or type

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

S&F mild steel angles/flat iron as in fencing post and struts including embeeded in concrete and screwing etc including securing bolts, cutting tops to shape as directed, drilling holes notching for wire, etc complete all as spficied Fe 290 Gde E-165, complete all as specified and directed.

S&F Rolled mild steel as in Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. of Fe-290 (Gde E165) complete all as specified and as directed.

S&F MS Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle of Fe 410-w (Gde E 250) quality A complete all as specified and as directed

Excavating over areas, not Exc 1.5 m deep and getting out in soft/loose soil.

Removing excavated material n .exc 50 m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

M&L PCC 1:3:6 type C2 ( with 40 mm graded agrregate) in Surface channel or drains including necessary form works , stops ,moulds etc complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including necessary forms mould mitred /stopped ends etc

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil

BOQ ITEM NO. 104 TO 165 FOR JOB NO. LSA/DWP//45/SRW/2025-26 M&L Prepration new plastered surfaces and applying three coat of white wash on ceiling all as specified.

S&F for in repair three layer rotational moulded polyethylene water storage tank cylindrical hoisted & fixed in position incl dismantiling water tank complete all as specifed capacity 1000 ltrs.

S&F in repair 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density Plastic ball Screwed for iron pipe and fixed (Minimum weight -210 gms. Make Prayag/Polytuff

Dismantling of stone slabs and tiles of any description or thickness in floors, platform, aprons etc laid bedded and pointed in any mortar

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, all as specified and directed

S&F vitrified ceramic tiles dark shade digital tiles/(double charged), 10mm thick (square/ rectanglar) polished , exceeding 0.18 sqm of each tiles not exceeding 0.38 sqm, in floors etc. laid over 15mm thick screed bed 1:6 , set and jointed in neat cement slurry and pointed in white/coloured cement to match complete all as specified. Make : Somany,/Johnson/Kajariya

M&L Glazed ceramic tiles (coloured) in vertical surfaces 600x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to matchover 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

S&F 75x50mm single rebated factory made 100% solid WPC (Wood Polymer Composit) door frame from 100% lead free ( Single & extruded process) material with dencity not less then 780kg /Cum all as specified and directed.

S&F Factory made 30 mm thick 100% solid WPC (Wood Polymer Composite) solid both side prelem 0.14 micron Flush door shutter wit 10mm deep CNC moulding design of required size comprising of virgin PVC resin of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F 30mm thick factory made solid WPC (Wood plastic composit) moulded glzed door shuter with wire mesh in 08 number of division with brown wood grain texture including SS wire mesh (G-304) 0.36 mm minimum dia of wire and average width of aperature 1.4mm with XPM Aluminium alloy wire cloth of wire shall to be fixed with 15x15 square tube in side rails with screwing 8x28 heat metel zink coated screws can be remove of fix again after changing of wire mesh needed. The density not less then 780kg /Cum shall be as per manufacture instruction complete all as specified and as directed

S&F powder coated alumium glazed window shutter sliding type using 1.30 mm thick aluminium open three track section having size of style & top rails 83x44mm, bottom rils 100x44mm Make jindal/Hindalco including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading screws, anodised aluminium fittings complete and glazing shall be done by using 5mm thick plain sheet glass Make- Modi guard/saint gobin) and stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm all as specified

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F 4.00 mm thick sheet frosted glass and glazing with oil putty/Aluminium beads in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces ground or obsecured to one side complete all as specified.

S&F 18 mm thick solid WPC board of density @ not less than 600kg/Cum one side prelaminated decoratiove teak face and other side white and balancing as in kitchen shelf, shutters etc including chawkats and all fitting accessories etc including dismantling, complete all as specified and directed

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps 30mm (when open) fixed with CP steel screws.

S&F 250 mm long Stainless steel sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolt and sliding bolts all as specified

S&F for Stainless steel barrel tower bolts 200 mm of extruded section and fixed.

S&F for Stainless steel barrel tower bolts 150 mm of extruded section and fixed.

S&F 125 mm size Stainless steel handles fabricated type extruded section ,ISI marked all as specified

S&F 150 mm size Stainless steel handles fabricated type extruded section ,ISI marked all as specified

S&F Butt hinges 125 mm stainless steel hinges medium weight and fixed

S&F 100 mm Stainless steell Butt hinges type B-21 and fixed

M&L for preparation of newly wood based materials of any description over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

S&F in repair. Vitreous china squatting pan Orissa pattern size 580x440 mm white with P or S trap front or back inlet with integral foot rests (excluding flushing cistern and flush pipe ) complete including provision of lime concrete bedding

S&F in repair Vitreous china wash hand basin white angle back size 550x400 mm including 32 mm dia CP waste coupling long screwed shank fly nut flanged end and embedded in lead to waste pipe excluding piller taps complete fixed specified and directed by enginner -in-charge.

S&F 110mm PVC (SWR) junction single (single T) equal or unequal

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or wall all as specified and directed.

S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber rings joints laid in trenches or in floor/wall all as specified and directed by Engineer-in-charge.

S&F 110mm bore PVC (SWR) bends, any radius.

S&F PVC (SWR) bends any radius of 75 mm dia all as specified.

S&F PVC (SWR) 75mm floor trap, plain with grating including jointing with solvent cement

S&F 15mm dia fancy type chromium plated bib taps cast copper alloy with crutch or butterfly handle, scresed down screwed for iron pipe or for brass ferrule and fixed both ends for iron pipe or for unions

S&F in repair 15 mm dia fancy type chromium plated Pillar tap cast copper alloy chromium plated fancy type with capstan head and cup screwed down screwed for G I pipe or for brass ferrule all as specified.

S&F 15mm dia fancy type chromium plated concealed stop/Angle cock for 15 mm bore pipe fixed as in repair

S&F as in repair CP soap dish any type fixed to plugs with chromium plated brass screws all as specified.

S&F CP brass towel rails 20 mm dia and 600 mm long fixed as in repair incl chromium plated brass screw and wooden / cleats

S&F in repairs 32 mm dia Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm 45gms/40mm-60 gms)

S&F in repairs 32mm dia PVC waste pipe approx 900mm long for sink/WHB complete all as specified.

S&F in repairs glass corner shelf assembly consisting of 5.5mm thick sheet glass 250X250mm size fixed with chromium plated brackets as in repairs all as directed.

S&F in repair glass self assembly consisting of 5.5 mm thick glass sheet glass self 12 Cm wide with CP bracket gaurd and railing 60 Cm long all as specified.

S&F in repairs PVC cabinet with mirror and door of size 560X410mm all as specified and directed.

S&F in repairs 125 mm dia CP brass shower rose with or without swivel joints any size including fixing to steel pipe or union add if fixed in repair all as specified and directed.

S&F in repair stainless kitchen plate rack made of 0.80mm thick sheet of size 900x1200 mm and fixed to wall complete all as specified.

Dismantling of Bricks (laid flat or on edge) or brick tiles in floors or roof laid beded and pointed in any mortar ,

M&L cement concrete type B-1, 1:2:4 (20mm graded aggregate) on roof slab all as specified and directed.

M&L for 10 mm thick on fair faces of concrete surfaces in cement mortar 1:3, mixed with liquid water proofing compound finished even and smooth without using extra cement. (Liquid water proofing compound to be measured paid separately) complete all as specified and directed.

M&L for application of high perfomance hybride polyurea elastomeric water proofing coating cold applied, liquid membrane at 1.5 kg/Sqm with an elongation minimum of 500+100% by roller and tensile strength of minimum 11-13 N/mm2 as per ASTM D2370, crack bridging ability minimum of 3 to 4 mm as per ASTM C1305 , Shore Hardness of minimum 70+5 as per ASTM D2240 complete as per directed by Engr-In-Charge. The System shall also include final base preparation including cleaning of the plaster surface etc and applying epoxy primer as approved makes in two coats at a coverage of 0.20 kg/Sqm, etc as per manufacturer specification, complete all as specified and directed. Note:- (a) The work petaining to water proofing treatment shall be executed from authorized applicator through manufacture of which the materials is proposed to be used by the contrator and approved by Garrision Engingeer. (b) The contractor shall upload along with the documents under technical bid (cover-1) 'Memorandam of understanding ' (MOU) with Only one manufacturer mention in the contract, falling which the bid shall be liable to be rejected.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil

M&LCement concrete 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete

S&F mild steel joist, channel, angle, or tee sections as in posts fixed independently, without connection plate, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe-410-W (Gde E-250)

S&F for trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etcof FE410-W (Gde E-250)

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed

M&L for Heritage Natural Stone Grit / Granules finishing white / colour in patches as directed by Engineer- in - Charge consisting of a two component dry granules made of 92% silica natural stone partiles coated with fade resistant priments of coating 0.8mm to 1.20mm to be applied in single coat of primer incl taking down old surface complete all as specified and as directed.

M&L for 15mm thick ready mix mixture of plaster in cement mortar 1:4 on external wall surface with white cement based polymer modified self curing mortar all complete all as specified and as directed.

M&L for complete removal of existing treatment by scraping with mechanical wall sander(having mechanical vacuum mechanism) having RPM not less than 1500,sanding pad of 80 Grit having dia of 7''/9'' to make the surface free from dust,loose paint etc by skilled labour complete all as specified and directed.

M&L for preparation of old plastered surfaces applying 2-3mm wall care putty Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.79 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) paint etc by skilled labour complete all as specified and directed.

M&L for preparation of new plastered surfaces applying 2-3mm wall care putty Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.79 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) paint etc by skilled labour complete all as specified and directed. Note:- The work for periodical services as mention in item No.163 to 165 shall be executed by the contractor as per MOU by the authorized nominated applicator of OEM of the paint, using wall sander machine for scrapping, applying cement based putty with automatic airless spray machine, applying specified primer and paint with full automatice spray paint machine.

Common EnM Items for both Jobs Taking down carefully aluminium point wiring with PVC casing capin and conduit (light, fan, socket or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets as required.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm ( Phase,- Red , neutral- Black) and earth continuity conductor 1.5 sqmm (green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia, ISI marked ivory colour with all conduit fittings / fixing accessories for the following :- (a) One light/ fan (CF & EF) point controlled by one switch.

(b) One bell point controlled by one bell push

(c)One 5 pin socket outlet 6 Amps on independent board controlled by one switch.

(d) One 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm ( Phase,- Red , neutral- Black) and earth continuity conductor 2.5 sqmm (green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 25 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories for 3 pin 16 amps socket outlet point controlled by one switch.

S&FSwitch Modular 6A single pole, one way, 1 module complete

S&F Switch Modular 16A single pole, one way, 1 module complete

S&F Socket, 6A - 2/3 pin combined 2 module complete

S&F Socket 6A/16A - 2/3 pin combined 2 module complete

Supply and fixing Exhaust fan steel body 300 mm sweep working on single phase supply incl. all accessories including electrical connection with required wire complete all as specified.

S&F in repair telephone socket 1 module complete .

Renewal of submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into and including concealed rigid non metallic PVC conduit 20 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes 2x4 sqmm + 1x4 sqmm earth wire complete.

Renewal of 20 amp , single pole and neutral socket outlet, with 2 poleand earth, metal enclosed plug top in powder coated CRCA steel sheet enclosure recess mounted with chained metal cover for the socket outlet with and incl one number single pole 'C' series MCB 16 amp as required.

Supply and fix in repair ceiling rose, internal polycarbonate body complete.

M&L for complete dismantling of split AC / window AC of any capacity by AC mechanic with gas back complete all as specified and as directed.

M&L for refixing of complete split AC / window AC of any capacity by AC mechanic including vacuuminising, leak proof, gas charging, servicing with water pressure jet & jacket complete proper functioning as specified and as directed.

EnM Items For Job No LSA/DWP/45/SRW/2025-26 S&F Modular White cover plate with frame,12 module complete .

S&F Modular White cover plate with frame,8 module complete

S&FModular White cover plate with frame,6 module complete

S&F Modular White cover plate with frame,4 module complete

S&F Modular White cover plate with frame,3 module complete

S&F Modular White cover plate with frame,2 module complete

S&F Modular Metal flush box 12 module complete

S&F Modular Metal flush box 8 module complete

S&F Modular Metal flush box 6 module complete

S&F Modular Metal flush box 4 module complete

S&F Modular Metal flush box 3 module complete

S&F Modular Metal flush box 2 module complete

S&F Calling bell , AC, 230 Volts, single phase complete

S&F bell push , AC, 230 Volts, 1 module complete

S&F Fan regulator 2 module sutitable for BLDC fans complete.

Renewal of decorative wall mounting type pre- wired LED light fitting, 1 x 15 Watt, 230 Volt made of Polycarbonate body including shade, lamp holder, 9/10 Watts LED lamp B22 CDL complete.

Renewal of integrated LED bulk head fitting 10 Watt, IP 66 IK-09 with polycarbonate body duly pre-wired connection with 0.75 sqmm PVC insulated & sheatthed three core flexiable multistd copper conductor cable complete .

Renewal of LED surface mounted batten 20 watt, powder coated die cast/ extruded aluminium Body (Thickness ≥ 1.20 mm) or CRCA sheet >0.5mm and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50 Hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5%), life time of LED minimum 50000 burning hours with 70% of initial Lumen maintained till life ends, CCT 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect including connections with suitable size FRLS, PVC insulated copper conductor cable and earthing etc as required with Minimum 5 year OEM warranty. System lumen efficacy 120 lm/Watt output. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as BIS shall be submitted (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Note:- Heat Sink of aluminium housing such that LED Junction temp shall not rise above 90 degree Centigrade.

Ditto as per item No 201 above but 10 watts and system efficacy 105 lm/watt or above.

Supply & fix recessed mounted 12 watt round LED ceiling lights SMD type with diffuser spring loaded having lumen output not less then 120 luman watt suitable for fixing in 3" juction boxex incl connection colplete.

Taking down carefully ceiling fan of any sweep complete with all accessories, dismantling blades and deposit in safe custody of AGE E/M Yard-II for BER procedure complete .

Renewal of submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable using colour coding drawing into and including concealed rigid non metallic PVC conduit 25 mm dia, medium grade, ISI marked ivory colour along with accessories of nominal sizes 2x10 sqmm + 1x10 sqmm earth wire complete.

Renewal of MCB distribution board , SPN 240 volts, 12 ways powder coated , CRCA steel sheet degree of protection IP 43 -IK 09 with double door, recess mounted having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate, in unused spaces as required.

Renewal of MCB, SP, AC, 240 volt of 06 to 32 Amp capacity "C" Series, ISI marked, incl making connections by using suitable copper lugs as required.

Renewal of MCB, DP, AC, 240 volt of 32 Amp capacity "C" Series, 10 kA ISI marked, incl making connections by using suitable copper lugs as required. Note :- for MCCB's , MCB's, MCB DBs, MCCB's , MCB's, MCB DB's shall be of the same make.

Renewal of MCB distribution board VTPN , 4 way, powder coated CRCA steel sheet suitable for MCCB incomer 125 Amp , 4 way 415 volt degree of protection IP 43 -Ik-09 with reversable double door, recessed mounted having 250 amp insulated tinned copper bus bar , neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plate, in unused spaces wherever required comprising of the following:- Incoming:- one number MCCB, 125 Amp, 04 pole, AC, 415 Volt, 50 Hz 16 KA ( Icu=Ics), thermally adjustable between 70 % to 100 %. Outgoing:- Twelve numbers MCB, SP, AC, 240 volt, 50 Hz, 10 KA, 32 A, 'C' series ISI marked.

Material and labour for earthing with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete.

Supply and fixing ceiling fans 1200 mm sweep, BEE star rated 5 with brush less direct current (BLDC) motor, class of insulation B, 3 Nos blades, up to 90 cm long down rod, canopies, shackels, kit, safty rope, copper winding, power factor not less then 0.9 service value ( CM/M/W) min 6.00, air delivery min 210 cum/min, 350 RPM ( tolerance as per IS: 374- 2019) THD less then 10 % remote unit for speed control and all remaining accessories incl safety pin, nut bolts, washers , tempr rise 75 degree C (max) , insulation resistance more then 2 mega ohm, suitable for 230 V, 50 Hz complete.

S&F Fresh air fan of size 200 mm sweep PVC body complete with louvers connection up incl suitable size three core flexiable copper cable from ceiling rose to Fresh air fan as required.

Supply and fix 35/45W Pressure die cast aluminium housing street light with system lumen of 6300 lm and system efficacy of 140 lm/w, IP-66,IK-10 single piece die cast incl spigot, dia 48-76mm,LED lifetime (L70B50) 75k Hrs with integrated optical cover. Street light should have standalone lighting control system with AUTO ON/OFF based on DUSK/DAWN timings,preset time settings with monthly variations (Jan to Dec), inbuilt real time clock for switching, incleds dimming profile for energy savings,drift not exceedind max 2mins/year, clock retention upto five yeras, auto switching off secondary power for module,dimmable driver based on PWM control, dim to off with high/low voltage cut off with 440V protection for 8 hrs for complete luminiarie incl driver and astro module,surge protection as perIEC 61000-4-5 incl MS Clamps and bracket of 40mm dia and fastener for fixing the light complete.

Cutting walls any type, making holes for fixing of exhaust fan of any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete.

Taking down carefully Geyser of any type and capacity complete with all accessories, dismantling and refixing at same place with new PVC hot series connection pipe after finish of civil work complete .

Taking down electric meter and refixing on new board after rewiring complete.

EnM Items For Job No LSA/DWP/45/SRW/2025-26 Supply and fix in renewal Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends,elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.PVC pipe 25 mm dia for protection of cables complete all as specified.

Supply and fix in renewal of MCB DB SPN 8 way 230 volts, double door type with minimum capacity of 100 Amps rated bus bar including necessary dummy plate and necessary civil works all as specified.

Supply and fix in renewal of MCB SP 230V, 6-32 Amps capacity complete all as specified.

Supply and fix in renewal of MCB SPN 230V, 32-63 Amps capacity all as specified.

S&f in renewal of call bell , ding dong AC single phase 230 volts complete all as specified.

Supply and fixing in renewal of wall/surface mounted integrated batten LED light luminaire of 4ft length with a system wattage of 18 watt , power coated die cast/extruded aluminium body (thickness>1.20mm) or CRCA sheet body (Thickness>-.50mm) and construction as per IS:10322 with driver (Replaceable) as per the reqmt with driver efficiecy >85%, system lumen efficacy 120lm/Watt output, operating voltage AC 140-270 volts, 50Hz, operating temp rang-15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with short and open ckt protection, THD<10%, PF>.95, IP20, CRI>80, Flicker free (flicker should be below 5%), life time (LED & electrical circuitary) of min 50000 burning horus with 70% of initial lumen maint till life ends, CCT 5700 degree K (As per ANSI Bin), SDCM (Std deviation color matching)<3, max power consumption should not more than the specified rating and fixture shall be of relevant BIS standard and std and trade mark cert (TC). Manufactures word kark/name engraved/embossing/screen printing on housing complete in all respect incl connections with suitable size FRLS, PVC insulated copper conductor cable and earthing etc as reqd with min 5 years OEM warrenty. LM79 & LM80 test report from NABL lab for all tests reqd for LED fixtures as BIS shall be submitted. Note:- Heat srink of aluminium housing such that LED junction trmp shall not rise above 90 degree Cel.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

S&F in replacement decorative wall mounted fancy light fitting made up of brass rubi lamp brand Single handed including of bulb of 9-15 watts covered by glass complete all as specified.

S&F LED bed side fitting 3 Watt 3000K 150lm complete all as specified .

Supply and fix in renewal 45W Pressure die cast aluminium housing street light with system lumen of 6300 lm and system efficacy of 140 lm/w, IP-66,IK-10 single piece die cast incl spigot, dia 48-76mm,LED lifetime (L70B50) 75k Hrs with integrated optical cover. Street light should have standalone lighting control system with AUTO ON/OFF based on DUSK/DAWN timings,preset time settings with monthly variations (Jan to Dec), inbuilt real time clock for switching, incleds dimming profile for energy savings,drift not exceedind max 2mins/year, clock retention upto five yeras, auto switching off secondary power for module,dimmable driver based on PWM control, dim to off with high/low voltage cut off with 440V protection for 8 hrs for complete luminiarie incl driver and astro module,surge protection as perIEC 61000-4-5 complete all as specified.

Supply and fixing in replacement of Solar integral AIO streetlight with Aluminium housing, reliable & robust construction with IP65 & IK08 protection. The luminare Lithium /LifePo4 Battery capacity min [email protected] or 20w4.5v pv panel power CRI >=70, System Efficacy >165lm/W, & Minimum Lumen 4000 system wattage should not be more than 25W ± 2%, if wattages increases then the size of battery & panel shall also be increased in similar percentage to maintain equal autonomy of the system. Weight not more than 2.32 kg . The fixture should have in microwave motion sensor &sensor dealy time 18 seconds Life class of LED 50000hrs@ incl clamps ,brackets and nut-bolts and other connected items for fixing the light on wall complete all as specified.

Supply and fix LED gate light of 40/45W LED Postop luminaire with aluminium pressure die-cast mounting spigot & polyester powder coating in addition to a specific weathering resistance treatment, color RAL7011. Non-yellowing transparent Polycarbonate UV-protected round symmetrical diffuser with circular radial pattern for glare-free and even light distribution. High Efficiency long life LED module with efficacy of >100Lm/W, CCT 4000K, and CRI >70. Powered by built-in electronic driver with THD <10%, 4kV inbuilt surge protection, high cut-off at 325V & auto-restart, including 8hrs. protection from 440V (P2P). Suitable for pole mounting having OD of 60 mm and height of 6 meters. Fixture lumen efficacy >4500 Lm, IP66 (no glue), IK05, PF>0.95, Operating voltage range: 140- 277V, complete all as specified.

Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 6 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 6 Sqmm drawn through and including PVC Conduit pipe 25 mm dia with all fittings complete all as specified.

Supply and fixing ceiling fans remote operated complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) with copper winding incl remote complete all as specified.

Supply and fixing of wall fan of 300 mm sweep, 220 - 240 volts, AC, 50 Hz 1330 RPM, 55 Watts power input, air delivery 65 Cum/min with all accessories complete all as specified.

Material and labour Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 connected to earth testing point including necessary excavation, earth work, PCC pit ,RCC cover 1:2:4 B1 with 8 mm dia MS rounds 1.5 kgs, funnel ,watering pipe etc complete all as specified.

Cutting chases in concrete wall/stone for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 20 cm girth and matching wall color.

Supply and fixing Exhaust fan PVC body 250 mm sweep working on single phase supply incl. all accessories including electrical connection with required wire complete all as specified.

Supply and fixing Digital storage water heater (Geyser) Square type of capacity 25 ltrs, 230 volts, power consumtion 230V, vertical type, Rated pressure 5.6 bar pressure rating more than 8 bar suitable for high rise buildings,rust and shock proof ABS Outer body for lomg life,Stainless steel inner tank of 304 grade,65 MPa bar pressure,colour changing lights that change from blue to amber to indicate the hotness of water,automatic shut off including four nos of rag bolts and making the elctrical / water supply connection including testing after installation complete all as specified.

Supply and fix GI Pipe light grade 80 mm dia for protection of cables complete all as specified.

Supply and laying XLPE Insulated armoured electric heavy power cable with aluminium stranded conductor ,1100 volts grade, cross sectional area 50 sqmm x 3.5 core complete all as specified

M &L for Excavation in trenches not exc 1.5 m wide and not exc 1.5m deep for laying of pipe, cable etc and getting out in soft/loose complete all as specified .

M&L for Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified .

M &L for Removing surplus excavated material to a distance not exc 50 meter and depositing where directed at level not exc 1.5m above the starting point complete all as specified.

S&L DWC HDPE Pipe along with all aceessories like socket , bend,couplersetc ISI mark as per IS: 16205 (PART-24) including cutting,jointing,laid in trenches,wall , floor,etc as required 63 mm outer dia and 50 mm inner dia complete all as specified

Taking down of Geyser of any capacity and deposited to AGE E/M Yard.

Taking down of ceiling fan /exhaust fan/wall fan/air freshner of any size and deposited to AGE E/M Yard.