Civil Works

Amount

Dismantling , removing and carefully stacking Floor finish & dadooing walls in cement mortar with Mosaic Tiles / Glazed Tiles / Clay Tiles / Cuddapah Slabs etc., complete complying with standard specification and as directed by the departmental officers at site of work.

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means

Brick work in following Cement Mortar 1:6 (One cement and Six sand) using best quality Fly ash Brick of size 230x110x70mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing, etc., complete complying with standard specification and as directed by the departmental officers. Brick work shall be done as per IS 2212-1991 adopting English Bond generally. other type of bond shall be done as directed by the Executive Engineer in charge.

In Ground floor

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Jet Black with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M.sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigmentsetc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M.sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with white glazed tiles of size 600x600x8mm best approved quality, colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Brick Jelly Lime Concrete 1:2:5 using 40mm brick jelly in Lime Mortar 1:2 using limestone and sand

Plastering with Cement Mortar 1:3 (One Cement and Three P.Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing Country Wood Frames for DOORS WINDOWS VENTILATORS and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors.

Manufacturing and supplying of 35mm thick solid core block board flush double leaves shutters with teakwood ply veneering on both sides hot pressed bonded with liquid phenol formaldehyde resins and external lipping by TW around rebate cutting etc as per IS 2002 part I of 1991 including TW lipping of size 35 x 12 mm including labour charges for fixing all furniture fittings and specials. The flushshutters should be ISI specification and got approved by the Departmental officer before fixing. Alu. fittings of 6" tower bolt -1 no, 4" tower bolt - 1 no, door stopper- 1 no, Aldrop - 1 no , hinges 6 " - 3 nos., ornamental lock and handle etc complete as directed by the departmental officers.

Supplying and Fixing of Wood Polymer Composite (WPC) door with solid door frames extruded with size 75mmX50mm. The Inner core made of rigid WPC compound with minimum shore hardness of 55, and Bulk Density 750Kg/cub.Mt. The frame shall be fixed to the wall using 10X10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screws to be provided for each vertical members,Door shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of Specified Design which is approved by engineer-In-Charge. Both side of the shutter shall have rough sugar texture finish, laminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550Kg/Cub.Mt moulding the thickness remains 25mm(+/-1mm) etc complete as per the direction of the departmental officers.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of teakwood colour of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The ventilatore should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Providing and Applying high build exterior waterproof coating for external wall, parapet & Chajja, which is single component, cold applied, Reactive Acrylate copolymer technology. Apply one base coat of universal elastomeric exterior waterproof coating @0.25L/m2 and 2nd coat with Acrylic emultion top coat which can be tinted to any colour @ 0.17L/m2, including 2 coats DFT will be min. 170 microns, The material having followed technical properties: Attains hairline crack bridging up to 2 mm as per EN 1062 part 7, Elongation of >100 % as per ASTMD 412; Tensile strength 2.50 Mpa per ASTM D 412, including priming the surface with 1 coat of Efflorescence resistant penetrating primer dilute with water in the ratio 2:1 spreading at the rate of 0.125 l/m2 in the SSD condition. The finished cost to include surface preparation, making coving at Junction, treatment of cracks completely as per specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Polishing the teak wood door with two coats of Melamine polish to wood surface as per direction etc., complete should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of neceSORy PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of “U” clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers

Supplying, laying and jointing UPVC pipes of Class 5 (having working pressure of 10 kg/ sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting, and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3(2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by executive Engineer before use on works. - Internal water supply - above ground level.

20 mm dia UPVC Pipe

25 mm dia UPVC Pipe

32 mm dia UPVC Pipe

50 mm dia UPVC Pipe

Supplying and fixing in position UPVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the UPVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

50mm dia UPVC Elbow

40 mm dia UPVC Elbow

32 mm dia UPVC Elbow

25 mm dia UPVC Elbow

20 mm dia UPVC Elbow

50mm dia UPVC Bend

40 mm dia UPVC Bend

32 mm dia UPVC Bend

25 mm dia UPVC Bend

20 mm dia UPVC Bend

50mm dia UPVC Tee

40 mm dia UPVC Tee

32 mm dia UPVC Tee

25 mm dia UPVC Tee

20 mm dia UPVC Tee

50mm dia UPVC Coupling

40 mm dia UPVC Coupling

32 mm dia UPVC Coupling

25 mm dia UPVC Coupling

20 mm dia UPVC Coupling

50x40mm dia UPVC Reducer

25 x 20 mm dia UPVC Reducer

40 x 32 mm dia UPVC Reducer

32 x 25 mm dia UPVC Reducer

50x40 mm dia UPVC Reducer Elbow

25 x 20 mm dia UPVC Reducer Elbow

40 x 32 mm dia UPVC Reducer Elbow

32 x 25 mm dia UPVC Reducer Elbow

50x40 mm dia UPVC Reducer Tee

25 x 20 mm dia UPVC Reducer Tee

40 x 32 mm dia UPVC Reducer Tee

32 x 25 mm dia UPVC Reducer Tee

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

40mm dia GM Gate Valve

32mm dia GM Gate Valve

25mm dia GM Gate Valve

Supplying and fixing in position 150 x 100mm “P” or “S” stoneware gully trap ‘A’ grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing position CI Nahani Trap of size 100x75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M.sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia “B” class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing in position 15mm dia brass CP screw down tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

160mm dia PVC soil / waste pipe

110mm dia PVC soil / waste pipe

75mm dia PVC soil / waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

160 mm dia PVC Tee

110 mm dia PVC Tee

75 mm dia PVC Tee

160 mm dia PVC Tee with single door

110 mm dia PVC Tee with single door

75 mm dia PVC Tee with single door

160mm dia PVC bend

110mm dia PVC bend

75 mm dia PVC bend

160 mm dia PVC Elbow

110mm dia PVC Elbow

75 mm dia PVC Elbow

160 mm dia PVC Elbow with door

110mm dia PVC Elbow with door

75 mm dia PVC Elbow with door

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 5.5mm thick mirror of following size , Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) Size :600 x 450 mm / 500 x 400mm / 1000 x 780 mm.

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The towel rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 100mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position GI unions of heavy duty of approved quality and good variety of various sizes inluding necessary cutting and threading of GI pipes for jointing the union and providing two coats of painting with good variety and approved quality of synthetic enamel paint over one coat of primer in case of pipe line above ground level / one coat of tar in case of below ground level for both internal and external water supply arrangements, etc., complete complying with standard specifications. (The GI unions should be got approved by Executive Engineer before use on works).

50mm dia

40mm dia

32mm dia

25 mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

160mm dia

75mm dia

110mm dia

Supplying and fixing of Granite Sink of size 600 x 600 x 250mm.including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Providing and fixing Stainless Steel health faucet rate is including the cost of materials, labour etc., complete as directed by the departmental officers.

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five M.sand] using best quality of Fly Ash Bricks of 230 x 110 x 75mm with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

Inspection Chamber of Size 0.60 x 0.60 x 0.60m (average depth)

Inspection Chamber of Size 0.60 x 0.60 x 0.90m (average depth)

Providing, mixing, laying polymer based water proofing treatment for the sunken toilet by applying cement based, flexible,water proofing compound confirming to IS:2645,to a thickness of 1mm of the prepared surface of the roof slab/floor slab as per specifications mentioned above providing cement mortar 1:3, water proofing over plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate inclusive of preparation of surface,which includes cleaning of surface polymer mortar curing,labour,tools and equipment,etc., Rate inclusive of cement and sand required for the treatement, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45 cm for drip pipes etc., complete.

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two Crushed Stone Sand and Four aggregate) using 6 to12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trowel, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Supplying and fixing in position SFRC manhole covers with SFRC frames (Heavy duty) of following sizes of best approved quality as per standard specification etc., complete compying with standard specifications

Size of 60x60cm

Supplying and erecting multistage open well submerssible pumpset of 2HP capacity with 50mm delivery pipe suitable for open well / sump driven by 3 phase power supply with necessary tying rope and bed arrangements. The rate inclusive of supply and erecting star-delta starter with suitable underwater cable from starter to motor.

SS Weighing Scale - 500 kg

Suppying and fixing Cold Room - Chiller of Dimensions (Mtr) Ext 2.5 (D) x 3.04 (W) x 2.44 (H) Ambient Temperature + 40 Deg C Room Temperature + 2 to + 8 Deg C Refrigeration systems and model RUAH 1014KP – 1 No- ODU + IDU R404a Gas Total refrigeration capacity 10000 BTUH x 1 No Power.

Suppying and fixing Cold Room - Freezer of Dimensions (Mtr) EXT 2.5 (D) x 3.04 (W) x 2.44(H) Ambient Temperature + 40 Deg C Room Temperature (-)20 deg C Refrigeration systems and model RUAL0914KP – 2 Nos – ODU RUAL0914KP – 2 Nos -IDU Total refrigeration capacity 9000 BTUH/Hr x 2 Nos

Suppying SS Rack - 4 Tire of Size: 45" X 24" X 60" of SS 304 Grade Materials

Suppying SS Pallets Size: 45" X 24" X 10" SS 304 Grade Materials

Supplying SS Weighing Scale - 300 kg

Supplying SS Two Sink Unit of Size: 45" X 24" X 34"+6" Sink Size: 18" X 18" X 12" SS 304 Grade Materials

Supplying SS Drain Table of Size: 45" X 24" X 34"+6" SS 304 Grade Materials

Supplying SS Onion & Potato Bin Size: 48" X 24" X 42" SS 304 Grade Materials

Supplying SS Work Table With 1U/S Size: 45" X 24" X 34"+6" SS 304 Grade Materials

Supplying Table Top Model Veg Cutting Machine With Blades 5 Nos

Supplying 20ltr Tilting Grinder 2HP Motor and 3 Phase of Brand approved by Executive Engineer

Supplying Instant Pulverizer 3HP Motor and 3 Phase of Brand approved by Executive Engineer

Supplying Masala Pulverizer 3HP Motor and 3Phase of Brand approved by Executive Engineer

Supplying SS Coconut Scrapper Standing Model 0.5HP Motor and Single Phase of Brand approved by Executive Engineer

Supplying 30Kg Potato Peeler 2HP Motor and 3Phase Supply of Brand approved by Executive Engineer

25Kg Dough Kneader 2HP Motor and 3 Phase Supplyof of Brand approved by Executive Engineer

Supplying SS Masala Trolley 12 Hole SS 304 Grade Materials

Supplying SS 304 Chinese 2 Burner Gas Range Size : 48" X 27" X 30" +18" SS 304 Grade Materials

Supplying SS Single Sink Size: 24" X 24" X 34"+6" Sink Size: 18" X 18" X 12" SS 304 Grade Materials

Supplying SS 304 Double Burner Gas Range Size: 48" X 24" X 24" SS 304 Grade Materials

Supplying SS Single Range Size: 24" X 24" X 24" SS 304 Grade Materials

Supplying SS Bulk Range ( Two Ring Burner) Size: 30" X 30" X 18" SS 304 Grade Materials

Supplying LPG - Bratt Pan 150Ltr SS 304 Grade Materials

Supplying SS Four Burner Range Size: 36" X 36" X 30" +6" SS 304 Grade Materials

Supplying SS Work Table With Sink Size: 45" X 24" X 34"+6" Sink Size: 18" X 18" X 12" HT SS 304 Grada Materials

Supplying SS Rolling Table With Top Granite Size: 45" X 24" X 34"+6" SS 304 Grada Materials

Supplying SS Dosa Dawa - Gas Model Size: 48" X 27" X 34"+6" SS 304 Grada Materials

Supplying SS Batter Trolley Size: 18" X 24" X 34" SS 304 Grada Materials

Suppling and fixing MS 500ltr Steam Boiler - Gas Model Steam boiler inner made of 12swg SS sheet and outer double Jacketed made out of 6 & 8mm MS sheet. The steam boiler consist of the following accessories. Per hour steam evaporation 127 Ltr. Steam Pressure 0 to 2kg . Gauge glass assembly ,safety valve, drain valve, water inlet& out let and valve for steam out Let. Per hour steam evaporation 126 Ltr Boiler Fittings 1. T78 Burner full set -2Nos 2. 3/8x3/8 Copper tube 3 feet length 3. 3/8x3/8 Nc Valve =2no,s 4.1⁄2” Gas pipe with fiƫngs 5. 1⁄2” dummy

Supplying SS Cooking Vessel single jacket 150ltr Capacity

Supplying SS Cooking Vessel Double jacket 100ltr Capacity

Supplying SS Steam Operated 200 Idly Box with Stand Outer Body and Inner Body made of SS 16swg 304 Grade. Door Made Of SS 16swg 304 Grade. Steam Controlled by Valve Operation . With Stand made of SS Angles and Square pipes with Adjustable nylon knob.

Supplying SS Pot Rack - 3 Tire Size: 48" X 24" X 60" SS 304 Grade Materials

Supplying SS Drainage Grating - 3Layer System Size: 24" X 12"

Supplying and erecting Gas Line Work MS 1/2" C Class Tada Pipe and all Fittings 1. L Fittings 2. T Fittings 3. Unions 4. On/Off Valves 5.Meter, Painting Work, Laying and Fixing Work.

Supplying and erecting SS 3/4" dia SS Steam line Pipe with fittings 1. SS Elbow 2. SS Hex Nipple 3. Union 4. Ball valve 5. Pipe line Welding work

Supplying SS 202 Exhaust Hood with filter 0.8mm thick sheet Size: 69' X 36'' X 20"

Supplying GI Duct for Exhaust 22swg 3'x2' duct size .

Supplying Support angle and Frames as per site conditions as approved by Executive Engineer

Supplying 10 HP Blower 3 Phase supply

Supplying MS Blower Stand as per site conditions as approved by Executive Engineer

Supplying Motor Starter of specifications as per site conditions as approved by Executive Engineer

Charges for Commisioning of complete Exhaust System as per site conditions as approved by Executive Engineer

Supplying GI Duct for Fresh Air system 22swg 1.5'x1.5' duct size as per site conditions as approved by Executive Engineer

Supplying 7.5HP Blower 3 Phase supply of brand approved by Executive Engineer

Supplying Aluminium Cooling Grill as per site conditions as approved by Executive Engineer

Charges for Commisioning of complete Fresh Air System as per site conditions as approved by Executive Engineer

B. SANKARAAN (BID ID -1376388)