Loading
Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹7.8 LAdmitted-Finance | -22.88% | ₹7.8 L | L1 | Admitted-Finance |
| 2 | L2₹8.1 LAdmitted-Finance | -20.22% | ₹8.1 L | L2 | Admitted-Finance |
| 3 | L3₹8.3 LAdmitted-Finance | -17.51% | ₹8.3 L | L3 | Admitted-Finance |
| 4 | L4₹8.4 LAdmitted-Finance | -16.85% | ₹8.4 L | L4 | Admitted-Finance |
| 5 | L5₹8.4 LAdmitted-Finance | -16.30% | ₹8.4 L | L5 | Admitted-Finance |
Tender Value
₹10.1 L
EMD Value
₹20,180
Closing Date
6 Apr 2026, 6:00 pmClosed
EE PHED DIVISION NOHAR
EE PHED DIVISION NOHAR
Replacement of old motor pump set for improvement of water supply at various wss sub div. rural rawatsar
2026_PHCJA_548630_1
EE/PHED/DIV/NOHAR/39/2025-26
Open Tender
Civil Works
60 days
RAWATSAR
Please refer Tender documents.
2 documents required · 2 mandatory
₹500
EE PHED DIVISION NOHAR
₹20,180
Yes
7 Apr 2026
26 Mar 2026
7 Apr 2026
26 Mar 2026
6 Apr 2026
26 Mar 2026
This is a percentage-rate BOQ. The schedule below shows estimated quantities and rates. Bidders quote a single percentage above or below the total estimated cost.
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount | Item Code |
|---|---|---|---|---|---|---|
| 15.5 Providing, installation, testing and commissioning of submersible monoblock pump set conforming to IS 8034 and 2 pole motor operating at syncronised speed of speed 3000 RPM, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V 10%, 3 Ph, 50 Hz AC and with water lubricated bearing to accept entire hydraulic thrust. Supply, with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pumpshould have suitable discharge out let as per manufacturer s design. Antithrust stream lined non return valve shall be provided with the pump and minimum 6 m submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm thick shall be provided with each pump etc. complete in all respect as per specification, scope of work and direction of Engineer in Charge of following power rating, suitable for prescribed duty conditions mentioned in TD.5.5.7 15.0 KW (20.0 HP) Discharge 20 to 25 LPS and head 35to 40 M ( 20 HP) | ||||||
| 21.6 Manufacturing, supplying ,lowering, laying and jointing in position to correct line spirally welded SAW /Fabricated MS Pipe having bevelled end plates / coils, confirming to IS 3589-2001 or its latest revision/ amendments, for following thickness and inside diameter, including all taxes (Central and local) ,transportation and freight charges, inspection charges, loading/ unloading charges, including cost of labour and material, specials (Tee, bend etc.), field joints, satisfactory hydraulic testing, disinfection, commissioning etc. complete as per technical specifications and direction of Engineer-in-charge; (excluding earthwork, internal lining and outer coating). Note : Providing and fixing of all requisite specials as per drawing, design and layout are inclusive in RM measurement of the item and shall not be paid separately. 1.6.1 Outer dia of pipe 219.1 mm and thickness 1.6.1.1 2.6 mm | ||||||
| 3Providing and fixing of flanged / plain ended MS Specials made from MS sheet strips of relevant IS specification of approved thickness by welding, lowering, laying, aligning, fixing in position at all level/ depths in trenches complete including all taxes, material, labour, inside lining, outside coating, testing andcommissioning along with pipe line as per technical specifications and direction of Engineer-in-charge.1.15.1 MS pipe specials upto 600mm dia (with minimum 5mm thickness sheet) | ||||||
| 4SITC of Soft Starters with panel supplied by manufacturer conforming to applicable standards with logic inputs & outputs, relay outputs and analogue outputs, plug in I/O connections, display of electrical parameters, state of load & operating time, RS 485 serial link for connections to Modbus.:37 KW | ||||||
| 5 | STAR DELTA STARTER 15.0 KW (20.0 HP) : For 2 motors (1 W+ 1S) I/C- MCCB 100A TPN 25 KA With T/M Based Over Current & Short CircuitProtection (1),Spreaders (2),Extended Rotary Handle (1) , Analog Voltmeter 96*96mm ( 0-500V ) (1), Volt Selector Switch (1) , Analog Ammeter 96*96mm ( 0-60A ) (1), Amp.elector Switch (1), C. T. 100/5A CL 1.0 5VA (3) , Indicating Lights ( Red-1, Yellow -1) (2), Indicating Lights ( Blue - 1 ) (1), Control MCB 6A SP 10 KA C Curve (3) and O/G- MCCB 63A TPN 25 KA With T/M Based Over Current & Short Circuit Protection (2), Power Cont 32A TP AC3 Duty(2), 2 NO+2 NC Aux. Block(2), Thermal Overload Relay (12-18A )(2), Control MCB 6A SP 10 KA C Curve (2), Single Phase Priventer (2), Indicating Lights (Red- 1, Green - 1, Amber-1)(6), Push Button 22.5 ( Red - 1, Green - 1 )(4), Selector Switch 1 Pole, 2 Way (2), Capacitor 440VAC Heavy Duty MPP Type 7.5Kvar (2), S/D Timer(2) | 1 | Each | - | - | BI01010001010000000000000515BI0100001116 |
| 66.8 Providing, lowering, aligning, fixing in position in pipe line at work site, DI D/F Resilient seated (soft seated) Sluice Valves (Gate Valves) , Vacuum tight(bubble tight), straight and pocket less body passage of approved make of following class & dia complete confirfing to BS-EN-1171/ AWWA C-509 and of following specifications: Body & bonnet of Ductile cast iron of grade GGG40/GGG50 as per DIN 1693 or GR SG-400/12 as per IS 1865 or equivalent grade as per IS :3896 part 2-1985 and subsequent revisions, Wedge of same material as body & shall vulcanised rubber lined with EPDM (food grade quality) and seals of NBR Face to face dimensions as per BS 5163-89/ IS 14846/2000 (amended up to date) /Din 3202 F4, Stem/ spindle of SS AISI 316/ 410 Electrostatic epoxy powder(EP-P)/ Fusion bond epoxy ( Non-Toxic- suitable for drinking water) coated with minimum thickness of 250 microns inside and outside,Drilled as per IS 1538. Nut-Bolt confirming to IS:1363 and IS: 1367 (Galvanised steel) Insersion rubber of black EPDM 6mm thick. Suitable support structure as per directions of EIC, Sluice valves including all jointing & jointing material, labour, testing and commissioning along with pipe line as per Technical Specifications and as per direction of Engineer-in-charge. Note: Rates are exclusive of tail piece / dismantling joints and earth work. 6.8.1Manually Operated Resilient Seated Sluice Valves of Class PN 1.66.8.1.3 150 mm dia | ||||||
| 7..---------do------------- 200MM | ||||||
| 8Providing, lowering, laying, aligning, fixing in position CI Foot valves in pipe line as per IS:4038-1986 (amended upto date) suitable for potable water at all level/ depth including all material, labour hydraulic testing and commissioning as per technical specifications and as per direction of Engineer for following sizes:150 mm dia | ||||||
| 9Providing, lowering, laying, aligning, fixing in position CI Foot valves in pipe line as per IS:4038-1986 (amended upto date) suitable for potable water at all level/ depth including all material, labour hydraulic testing and commissioning as per technical specifications and as per direction of Engineer for following sizes:200 mm dia | ||||||
stage.html
html • 0.04 MB
technical_978092.pdf
techsummary_978092.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.57 MB
TD01.pdf
Tender Documents • 0.44 MB
BOQ_978092.xls
BOQ • 0.24 MB
Download all tender documents and submit your bid