Construction of 33 KV Line under EDC Kushinagar

Amount

Work No-1 Part A (Materials Provided by contractor)

33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor

33 KV ‘XLPE’ C/J Kit 3x300mm ST. through

Number Plate

Danger Board with Clamp

Barbed wire

Bolts, Nuts, & Washers

33 KV Polymer Pin Insulator

Polymer 33 KV Disc Insulator 70 KN

Disc fitting B&S Type

Top Channel 125X65X3200 mm with clamps

33 KV V type X-arm

X-arm clamps.

Stay Clamp for ST/PCC Pole with Nut and Bolt by 50x8 mm MS Flat Iron make.

Stay Rod 20x1800 mm

Stay wire 7/8 SWG

MS Earthing Rod 20x2500 mm

P.G. Clamp for DOG

‘E’ Bracket for 33 KV

M.S. Angle Iron 65x65x6mm bracing

33 KV M.S. bracing Angle clamp with nut bolt for ST/PCC Pole with nut bolt by 50x8 mm MS flat Iron make

33 KV. Top channel (125x65mmX3200 mm (10.7 Kg/m)

Guarding Channel/Angle 75x40x3010mm

GI Wire 5 mm 6SWG

Guarding clamp with Bolt & Nuts

F Bracket for 33 KV

Extra angle for cable support

Clamp for extra angle support

Al. paint

Red oxide paint

PART - B- WORK Shifting, Loading Carriage & Unloading of following materials from store centre Gorakhpur to work site

33 KV Line Isolator

33 KV Line Isolator Structure

33 KV ‘XLPE’ Cable 3x300mm²

ST Pole 11 M Long

ACSR Dog Conductor

PCC Pole 9 M

MS angle for structure

Laying of 33 KV 3x300 mm² ‘XLPE’ cable(D/C) by digging pit & making trench in Proper size (1.2M depth x1.2M wide) below ground level by fixing bricks(4½˝) on both side of trench wall and 9˝ brick work at the centre of the trench along the cable. Fixing brick slab on top after filling sand around both the cable including cost of bricks and sand. as per site requirement HDD mathod can be used.

Jointing charge of 33 KV ‘XLPE’ C/J Kit 3x300 mm² Outdoor/ St. through

Laying of 33 KV ‘XLPE’ cable in air after providing 6” dia.M.S. pipe 3m long Complete work.

Special Pipe earthing for 33 KV Jointing Kit.

Extension of 11 mtr ST pole to 13 mtr all materials with work provided by contractor

Labour charges for rising of cable through MS Pipe and jumpering with complete work.

Erection of Single pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (‘V' type cross arm 100 x 50 x 6 mm, clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, barbed wire earthing, etc. complete).

Erection of Double pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete).

Erection of Four pole structure on 9 Mtr PCC Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete).

Erection of Double pole structure on 9 mtr PCC Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, barbed wire earthing, etc. complete) .

Erection of Single pole structure on 11mtr ST. (SP-55) Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories ( 'V' type cross arm 100 x 50 x 6 mm, clamps with bolt and nut, composite polymer pin insulator, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete).

Erection of Double pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) .

Erection of Double pole structure on 11 mtr ST Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) .

Erection of Four pole structure on 11 mtr ST Pole including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) .

Grouting of stay rods (20 x 1800) mm including all work of excavation, cement concrete in size (0.60 x 0.60 x 0.30) m in ratio 1:4:8 cement, sand, 40mm brick ballast) as per drg including back filling, proper ramming etc. Fixing tightening &nozzling of stay wire with stay rod with the poles of required tension.

Chopping of branches of trees of eucalyptus, Neem, Keekar and other kind of trees along the route of the line and disposal of the same at suitable place. (Including existing line)

Guarding between two poles like single poles, double poles, four poles, etc. to guard LT, 11 KV Line telephone and river crossing, road crossing etc. with G.I. wire no. 6 SWG and G.I. wire no. 8 SWG, cutting, fabrication and fixing of guarding channel 75 x 40 x 3010 mm with clamps nut & bolts etc.

Erection of Line Isolator Structure and install Line Isolator and earthing complete work.

Work No-2 Part A (Materials Provided by contractor)

33 KV ‘XLPE’ C/J Kit 3x300mm² Outdoor

33 KV ‘XLPE’ C/J Kit 3x300mm ST. through

Alluminium Paint

Red Oxide Paint

Bolts, Nuts, & Washers

M.S. Angle Iron 65x65x6mm bracing with clamps

Top Channel 125X65X3200 mm with clamps

Polymer 33 KV Disc Insulator 70 KN

Disc fitting B&S Type

Polymer 33 KV Pin Insulator

P.G. Clamp for ‘Dog’

‘E’ Bracket for 33 KV

Stay Rod 33KV , 20*1800mm

Stay Clamp 33KV

Stay wire 7/8 SWG

G.I. Wire 5mm 6SWG

Extra angle for cable support

Clamp for extra angle support

PART - B- WORK Shifting, Loading Carriage & Unloading of following materials from store centre Gorakhpur to work site

ST Pole 11 M Long

STP Pole 9 M

33 KV ‘XLPE’ Cable 3x300mm²

ACSR Dog Conductor

Laying of 33 KV 3x300 mm² ‘XLPE’ cable by digging pit & making soil trench in Proper size(1M depth x1M wide) below ground level by fixing bricks(4½˝) on both side of trench wall and 9˝ brick at the centre of the trench along the cable.Fixing brick slab on top after filling sand around both the cable including cost of bricks and sand. (as per site requirement HDD mathod can be use).

Jointing charge of 33 KV ‘XLPE’ C/J Kit 3x300 mm² Outdoor /Straight Through

Rising of 33 KV ‘XLPE’ cable in air after providing 6” dia.M.S. pipe 3m long Complete work.

Labour charges for inserting of MS Pipe, Rising of 33 KV cable and jumpering complete work.

Special Pipe earthing for 33 KV Jointing Kit.

cost for laying of 3x300 mm² ‘XLPE’ cable with HDPE Pipe for passing of 33 KV Cable under road Crossing in the path of Laying of cable.(HDPE pipe & all related materials with work provided by contractor)

Erection of Single pole structure on 11mtr ST. (SP-55) Pole for converting S/P to D/P including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, bolt and nut, composite polymer pin insulator,Polymer Disc Insulator with fitting, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete).

Erection of Double pole structure on 9 mtr ST Pole for only cable rising including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) .

Erection of Double pole structure on 11 mtr ST Pole for One side O/H and One side U/G line including all works of evocation of pit, pole erection, making plinth for poles 30 cm above, grouting in the ratio 1:4:8 (cement, sand, 40 mm brick ballast), back filling of earth, proper ramming & fitting of all accessories (M.S. angle iron 65 x 65 x 6 mm bracing with clamps, top channel 125 x 65 x 3200 mm with clamps, danger board with clamp, Aluminium paint, red oxide paint, barbed wire earthing, etc. complete) .

M/s Anil kumar singh

ARK ENGINEERING