Construction of 50 Bedded District Hospital Complex and Procurement of Equipment at Khawzawl, Mizoram.

Amount

Earthwork in excavation exclusive of compensation of earth in -(b) Hard Soil ( pick work )

Earthwork in excavation in foundation trenches or drains etc. (not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m including getting out excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres.a) Oridinary Soil

(b) Hard Soil ( pick work )

c) Very Hard Soil ( jumper work )

Earthwork in excavation in foundation trenches etc. not exceeding 2 meters depth including dressing of bottom and sides of trenches and subsequent filling and compaction in 15cm layers as in column foundations, fence posts, etc. and disposal of all surplus soil as directed within a lead of 30 metres.b) Hard Soil ( pick work )

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.b) Oridinary Rock

Providing and laying in position cement concrete of specified grade excluding cost of centering and shuttering - All work upto plinth level:a) 1:1.5:3 (1 cement :1.5 course sand :3 stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding cost of centering and shuttering - All work upto plinth level:(a) 1:3:6(1 cement : 3 course sand : 6 stone aggregate 20mm nominal size)

(b) 1:3:6(1 cement : 3 course sand : 6 stone aggregate40mm nominal size)

Providing and laying in position reinforced cement concrete excluding cost of centering and shuttering , finishing and reinforcement in - (b) 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. “(Note:- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately) a) All works upto plinth level.

b) All works from plinth level upto floor V level

Steel reinforcement for RCC work including straighthening, cutting, bending, placing in position and binding all complete.(b) Thermo-Mechanically Treated bars of grade Fe-500 or more.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :(a) Foundations, footings, bases of columns etc. for mass concrete.

b) Walls including attached pillasters, buttresses, string courses, etc.

(c) Columns, pillars, piers, abutments, posts and struts.

(d) Lintels, beams, plinth beams, girders, bressumers and cantilevers, etc.

(e) Suspended floors, roofs, landings, shelves and their support, balconies and chajjaj,etc.

(f) Staircases (except spiral staircase) excluding landings.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Carriages of earth by Mechanical transport,etc.(b) Earth :-For a lead of 5km

Half brick masonry with first class brick in foundation and plinth in:a) in cement moratar 1:3 ( 1 cement : 3 coarse sand )

Half brick masonry with first class brick in superstructure above plinth level upto floor V level.(a) in cement moratar 1:3 ( 1 cement : 3 coarse sand )

15mm cement plaster 1 : 3 (1 cement : 3 fine sand).

20mm cement plaster 1 : 3 (1 cement : 3 fine sand).

20mm cement plaster 1 : 3 (1 cement : 3 fine sand) finished with a floating coat of neat cement.

Extra for providing and mixing water proofing chemical (latex or equivalent chemical) @ 2kg per bag of cement in -a) 12 mm cement plaster 1 : 3 (1 cement : 3 fine sand).

(c) 15mm cement plaster 1 : 3 (1 cement : 3 fine sand).

e) 20mm cement plaster 1:3 (1 cement :3 sand)

12mm cement plaster 1 : 3 (1 cement : 3 fine sand).

6mm cement plaster 1 : 3 (1 cement : 3 fine sand).

Applying double coated PIDIFIN-2K on the surface of cement concrete for prevention of water infiltration and dampness in water tanks, basement, terraces, etc. ) @1.85kg per sqm.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) c) Granite (general black)

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing Ist class teak wood dressed in frames of chaukhat for doors, windows, clerestory windows fixed in position.

Providing Ist class local wood dressed in frames of chaukat for doors, windows, clerestory windows fixed in position.

Providing and fixing 1st class teak wood panelled shutters for doors etc. including M.S. butt hinges with necessary screws, etc. complete.(b) 35 mm thick.

Providing and fixing readymade door (Masonite or equivalent quality) including M.S. butt hinges with necessary screws complete.(b) 35 mm thick.

Providing and fixing 25mm thick MDF board greenply or equivalent panelled shutters for cupboards etc. including butt hinges, handles, and locking arrangments complete. a) Using MDF board greenply or equivalent.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.)trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Supplying and fixing M.S. decorative railing consisting of top and bottom rails of 40mmx40mm square or circular section at distance of 788mm apart, 30mmx30mm square or circular section decorative intermediate balusters welded to top and bottom rails at 280mm apart. The base of balusters at 560mm apart welded with base plate of 60mmx3mm thick and fixed with cement grouting firmly to concrete section including steel priming and steel painting complete etc.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of 80cm high in staircase, etc consisting of 75mm for rail and post, 63mm for longitudinal intermediate rail and 25mm of vertical section, spacing 125mm interval and as per approval of Engineer-in-charge.

Supplying and fixing pre-painted galvalume roller door shutters of approved make (Dura Ultima or equivalent), made of required size of curtain panel, bottom rail, polyglide, guide channel, bracket, spindle assembly (spindle, spring, drum wheel) and lock system including the cost of providing and fixing complete.(c) Economy roller door shutter

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required. (Glazing to be paid for separately) (b) Anodised

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(b) With glass panes of 5.00 mm thickness.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS: 733 and IS : 1285, anodised transparent or dyed to required shade according to IS : 1868 . (Minimum anodic coating of grade AC 15), fixed with rawl plugs and screws or with fixing clips , or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately ). For fixed portion.b) Anodised

Providing and fixing MDF board walling with necessary screws etc. complete.b) With 17mm thick MDF Board

Providing and fixing brass sliding door bolts (aldrops) bright finished with nuts and screws etc. complete.a) 300 x 16 mm

Providing and fixing bright finished brass two lever mortise door lock with necessary screws, etc. complete.b) Knob type

Providing and fixing Brass Tower Bolts (Socket Bolts) bright finished with necessary screws etc. complete.a) 300 mm

Providing and fixing brass handles with necessary screws, etc. complete a) 150 mm

Providing and fixing CP Brass Sliding Door Bolts (aldrops) bright finished with nuts and screws etc. complete.(a) 300 x 16 mm

Providing and fixing CP brass tower bolts (socket bolts) bright finished with necessary screws etc. complete.(b) 200 mm

Providing and fixing CP brass handles with necessary screws, etc. complete (a) 250 mm

Providing and fixing Curtain Rod with necessary screws & fittings, etc. complete.(a) Bright finished

Providing and fixing Curtain Rope hook with necessary screws , etc. complete.(a) Brass

Coursed masonry with rectangular sized hard stone in foundation upto one storey above and below ground level (b) in cement mortar 1 : 4 ( 1cement : 4 fine sand)including curing, etc. complete.

Back filling behind abutment, wing wall and return wall complete as per drawing and Technical Specification.(a) Gravelly material.

12mm cement plaster 1 : 4 (1 cement : 4 fine sand).

Applying priming coat with ready mixed primer of approved brand and manufacture on plaster surface.a) Ready mix white primer.

French spirit polishing (two or more coats) on new works including a coat of wood filler :

Coloured polished granite slab of size not less than 1200mm x 600mm x 20mm thick in flooring, treads of steps and landings laid over 20mm (average) thick base of cement mortar 1:4 and jointed with white cement slurry including rubbing and polishing complete. (a) General black

Coloured polished granite slab 20mm thick in skirting, riser of steps, dado,vertical face of pedestal etc. laid on 12mm (average) thick base of cement mortar 1:3 and jointed with white cement slurry including rubbing and polishing complete.

Providing and fixing 150 mm bright finished brass floor door stopper with rubber cushion, screws, etc. to suite shutter thickness complete.

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS:15622,of approved make, in all colours and shades, laid on bed of 20mm thick cement mortar 1 : 4 (1cement:4course sand), including the joints with white cement and matching pigments etc.complete.as per design collours.© Double charge

Providing and fixing on wall face SWRPVC soil, waste and vent pipes including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia.

Providing and fixing SWRPVC plain bend of required degree (45°) including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing & laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS:15622,of approved make, in all colours and shades, in skirting/dado, riser of steps, over 12mm thick bed of cement mortar 1:3 (1cement:3course sand), including the joints with white cement and matching pigments etc.complete.© Double charge

Providing and ceramic glazed floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS: 15622 of approved make in all colours,shades, except white,ivory,grey,fume red brown, laid on 20mm thick cement mortar 1 : 4 (1cement : 4 course sand ) including pointing the joints with white cement and matching pigments etc. complete. as per designed colour. ( b ) Matt/Antiscratch

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to e specified by the manufacaturer),of approved make, in all colours, shades wxcept burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12mm thick bed of cemunt mortar 1:3 (1cemeny :3 coarse sand) and jointing with cement slurry @ 3.3kg per sqm,

Providing Trapezoidal Polyester Coated Galvanised Steel Sheets Roofing of any colour of 1.06m width at all levels including fitting and fixing ridging with self drilling , self tapping screws, EPDM washers etc. complete excluding the cost of purlin, rafter and trusses.ii) For 0.50 mm thick :

Providing and fixing G.I steel frame works for ceiling lining consisting of battens 50x25mm fixed over plugs embedded in wall with necessary screws, etc. complete.

Supplying, fitting and fixing PVC board ceiling with nescessary screws etc. complete excluding frame work of base and beading.

Applying priming coat with Top Seal 109hi for waterproofing on roofs etc. , crack bridging etc. on concrete structures .

Applying single coated cement slurry with water proofing chemical (latex or equivalent chemical) in proportion 1 : 4 : 5 ( 1 latex : 4 water : 5 cement ) including cleaning the treated surfaces with brushes etc.

Wall painting with water and weather proof paint (Latex Emulsion base ) on cement works of approved brand and manufacture (ISI/ISO certified) of required shade on new work (two or more coats) to give an even shade .

Applying priming coat with ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) & Plywood.

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works.

Painting with synthetic enamel paint of approved brand and manufacture in all shades on new work (two or more coats).(b) High gloss

Finishing walls with exterior emulsion of required shade on new work (three or more coats) to give an even shade.(b) Premium exterior emulsion like weather shield, weathercote, etc.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (one or more coats)

Diluting and injecting chemical emulsion for post constructional anti termite treatment with Chlorpyriphos/Lindane emulsifiable chemical 20% with 1% concentration.© Treatment of soil under existing floor using chemical emulsion @ 1 litre per hole, 300mm apart including drilling 12mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1cement : 2course sand : 4stone aggregate 20mm size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement complete.(a) 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Honey-comb half brick masonry with first class brick in foundation upto one storey above and below ground level including curing, etc. complete. (a) in cement moratar 1:3 ( 1 cement : 3 coarse sand )

7.5 cm thick brick masonry with first class brick in superstructure above plinth level upto floor two level including curing, etc. complete (a) in cement moratar 1:3 ( 1 cement : 3 coarse sand )

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm uPVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:(a) Orrisa pan with integral type foot rests. (i) White

Providing and fixing vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :(i) White

Providing and fixing chromium plated brass shower rose with 15 or 20mm inlet.(a) 100mm dia CP brass shower rose.

Providing and fixing Health faucet with flexible tube upto 1 metre long and holder of quality and make as approved by Engineer - in - charge..

Providing and fixing White vitreous china wash basin Standard of Parryware/ Hindware/ Cera and equivalent make with R.S. or C.I. brackets, 15mm C.P. brass pillar taps, C.P. brass chain with rubber plugs, 32mm C.P. brass waste of standard pattern, 32mm C.P. brass traps and union complete including painting of fittings and brackets, cutting and making good the walls wherever required.(a) Vitreous China Wash basin size 630x450 mm with single 15 mm C.P. brass pillar taps

(b) Vitreous China Wash basin Compact 450 x 300 mm with single 15 mm C.P. brass pillar taps

Providing and fixing vitreous china tall pedestal of Parryware/ Hindware/ Cera and equivalent make for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick asbestos sheet ground fixed to cleats with C.P. brass screws and washers.

Providing and fixing C.P. brass towel rail with two C.P. brass brackets to wooden cleats with C.P. brass screws.a) 750x20mm size..

b)600x200 mm size

Providing and fixing toilet paper holder.

Providing and fixing liquid soap container with C.P. brass lid and brackets to wooden cleats with the same materials etc complete.(a) Glass container with CP lid and bracket

Providing and fixing soap dish fixed with C.P. brass screws.

Providing and fixing on wall face SWRPVC soil, waste and vent pipes including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia.

(b) 75mm dia.

Providing and fixing SWRPVC plain bend of required degree ( 87.50° ) including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia.

(b) 75mm dia.

Providing and fixing SWRPVC plain bend of required degree (45°) including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia.

(b) 75mm dia.

Providing and fixing SWRPVC bend with access door of required degree including jointing with rubber lubricant/cement solvent complete.(a) 110mm dia SWRPVC bend with access door.

(b)75mm dia SWRPVC bend with access door.

Providing and fixing single equal SWRPVC plain junction of required degree ( T-junction ) .(a) 110x110x110mm.

(b) 75x75x75mm.

Providing and fixing single equal SWRPVC plain junction of required degree with access door (T-junction) .a) 110x110x110mm.

Providing and fixing SWRPVC plain junction of required degree with access door (Y-junction) including jointing with rubber lubricant/cement solvent.a) 110 mm Y-junction of SWRPVC with access door.

Providing and fixing SWRPVC socket including jointing with rubber lubricant/cement solvent.a) 100mm dia socket

Providing and fixing ventilation cowl including jointing with rubber lubricant/cement solvent complete.(b) 75mm SWRPVC vent cowl

Providing and fixing W.C. connection bend type (siphon) (SWRPVC) including jointing with rubber lubricant/ solvent cement.

Providing and fixing uPVC multi floor trap with floor trap grating including jointing with rubber lubricant/ solvent cement complete.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.(a) Sintex or quivalent

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work. © 25mm dia nominal bore.

Providing and fixing G.I. pipe complete with G.I. fitting including trenching and refilling etc. (external work).For External Connection :-(b) 20mm dia nominal bore

(c) 25mm dia nominal bore

(d) 32mm dia nominal bore

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid seperately).

Making connection of G.I. distribution branch with G.I. main 25mm to 40mm nominal bore by providing and fixing Tee including cutting and threading the pipe etc. complete.

Providing and fixing brass stop cock of approved quality.b) 20mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) .b) 20mm nominal bore

Providing and fixing brass bib cock of approved quality.b) 20mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.(b) 20mm dia nominal bore Internal work - Exposed on wall

(d) 32mm dia nominal bore

Extra for concealed in brick and RCC works by making chases upto 7.5x7.5cm in walls and making good the same after housing pipes, etc.(b) 20mm dia nominal bore

Making connection of CPVC pipes distribution branch by providing and fixing equal Tee with jointing, testing complete including cutting and making good etc.(b) 20mm dia nominal bore

(d) 32mm dia nominal bore

Providing and placing in position electric water pump of approved manufacture including connections to G.I pipes etc. complete with accessories.(b) 750 watts

Providing and fixing brass bib cock of approved quality.(b) 20mm nominal bore

Providing & Fitting Cap for end pipe etc. complete .(b) 20mm

Providing and fixing CPVC Ball valve/ Globe/Stop & Waste valve/ Boiler drain etc. Complete.(b) 20mm nominal bore

Making connection of Astral CPVC pipes distribution branch by providing and fixing Elbow 90o with jointing, testing complete including cutting and making good etc.b) 20mm dia

Providing and fixing CPVC Ball valve/ Globe/Stop & Waste valve/ Boiler drain etc. Complete.b) 20mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.(d) 20 mm nominal bore.

Making connection of Astral CPVC pipes distribution branch by providing and fixing Male Adaptor (Brass) with jointing, testing complete including cutting and making good etc.b) 20mm nominal bore

Making connection of Astral CPVC pipes distribution branch by providing and fixing Female Adaptor (Brass) with jointing, testing complete including cutting and making good etc.b) 20mm nominal bore

INTERNAL ELECTRIFICATIONS LIGHTING AND POWER WIRINGS Wiring in looping system with PVC wire sheathed standard copper conductor/wires as per IS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexible wire stranded copper running inside PVC casing & capping (Gr-II) of different sizes fixed, surface on the wall/ceiling/floor as per convenience including junction box having required numbers of ways from control switch to the light point etc as required: A. TO A LIGHT POINT : (a) One point controlled by one switch (B) Short point

(C) Medium point

(D) Long point

(b) Two points controlled by one switch

B. TO A WALL FAN POINT: (C) Medium point

Wiring in looping system with PVC wire sheathed standard copper conductor/wires as per IS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexible wire stranded copper running inside PVC casing & capping (Gr-II) 25x12mm fixed, surface on the wall/ceiling/floor as per convinience including junction box having required numbers of ways from DB to the power plug/socket 15/16A point etc. as required :- (D) Long point

Wiring in parallel system with PVC wire sheathed standard copper conductor/wires as per IS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexible wire stranded copper running inside PVC Casing & capping (Gr-II) 20x12/25x12/32x12/38 40X15/20mm dia' fixed,surface on the wall/ceiling/floor as per convenience including junction box having required numbers of ways from Main to Sub-Main/DB/Sub-Main/DB to SDB/SDB/Switch boards/SDB to switch boards as required:- (A) 2X2.5 sq.mm

(B) 2X4sqmm

(C) 2X6sqmm

Wiring in parallel system with PVC wire sheathed standard copper conductor/wires as per IS:694(1990) and Flame retardant low smoke & Halogen (FR-LSH)1100 voltage graded copper flexible wire stranded copper running inside PVC Casing & capping (Gr-II)25/30/38mmx15mm dia' fixed,surface on the wall/ceiling/floor as per convenience including junction box having required numbers of ways from Main to Sub-Main/DB/Sub-Main/DB to SDB/SDB/Switch boards/SDB to switch boards as required:- (C) 4X6sqmm

(D) 4X10sqmm

LIGHTING FIXTURES AND FANS Supplying of all types of CFL/FL Ceiling mounted mirror optics/fibre cover/industrial type surface type with electronic ballast/ballast, condenser /electronic filter etc.in complete as follows:- a) Recess Mounting luminaires 2X36W FP-L HF MIRROR OPTICS AS SERIES mirror optic luminaire with electronic ballast suitable for AS/GB/POP ceiling. (Havells/ Phillps/Gromton/Bajaj)

b) Surface mounting luminaires 2 X 36W FP-L HF MIRROR OPTICS P5 (SURFACE) mirror optics luminaire with P5 Paralite louvre (Havells/ Phillps/Gromton/Bajaj)

c) Recess Mounting luminaires 2X18W FP-L HF MIRROR OPTIC - CABIN LITE P5 RECESSmirror optic luminaire with P5 paralite louvre for CFL/FP-L. (Havells/ Phillps/Gromton/Bajaj)

Supplying of all types of CFL and FL types FC tube in complete as follows:- CFL Curvy 15W (SP) B22,E27 Base Havells/Equivalent

Supplying,fitting and fixing angle Holder including connection etc, as required

Installation, testing & commissioning of pre-wired flourescent Light fittings of all types, with all accessories and tubes etc, directly on ceiling/wall, including supplying and fixing of ball and socket arrangement,2 Nos' down rod of 20mm diameter X 1.6 mm thick steel conduit pipe upto 30 cm length,painting and wiring the down rod and connection with 1.5 sqmm PVC insulated copper conductor single core cable etc, as required.

Supplying of pre-wired wall fan as per IS:374 (1979) in a set includ-ing socket type, canopy, AC wall fan machines,socket etc. in completed as folows:- Bracket wall mounting fan 400mm sweeps Mist air Ultra/Stiker High speed ISI marked

Installation, testing & commissioning of ceiling fan and regulator, including wiring the down rod of standard length (upto 30cm) with 2X1.5 sqmm PVC insulated copper conductor single core cable etc, as required.

E:03:00: LOAD LINE,MAIN DISTRIBUTION BOARDS,SWITCH BOARD ETC. SWITCH BOARD AND SWITCHES Supplying and fixing of Modular switch board of the following sizes/modules on surface/recess including PVC/Steel boxes,modular plate and necessary switches,plug/socket, and fan regulators etc. with necessary painting if necessary A. ONE MODULE (1) 1 S

B. TWO MODULES (13) 2 S

C. THREE MODULES (33) 3 S

D. FOUR MODULES (53) 4 S

E. SIX MODULES (76) 6 S

(91) 3 S + 1 Soc + 1 Bkp

F. EIGHT MODULES (128) 8 S

(156) 4 S + 1 Soc + 1 Bkp

Supplying and fixing of all types and ratings MCB’s RCCB’s etc 240/414V,50hz AC supply in the existing MCB DB complete with connection, testing and commissioning etc in complete. (1)5-32A SP MCB L/G Series

(36) 63 Amps' rating,FP, MCB Isolator

Supplying and fixing of different ways Maniature Circuit breaker(MCB) Distribution board(DB) single phase SP & N/Three Phase TP&N economy type with sheet metal,Acrylic cover Phosphatised powder painted, Bus Bar, Neutral link, earth bar anf din rail conforms to IS:13032 .IS:8623, BS:5486 240/415 volts, 50 Hz, AC supply on recess/surface including inter-connection,painting etc. in completed. (20) 8 ways (8+24) MCB DB TP&N D/D

(21) 12 ways (8+36) MCB DB TP&N D/D

LOAD LINE DISTRIBUTION BOARDS WITH MCCBs( out-going with MCBs) 6)12-ways MCB DB TP&N Loadline duobleDoor vertical suitable for G-frame MCCB (without MCCB)

EARTHING AND LIGHTNING ARRESTOR 51) Providing and fixing of 8 SWG Copper Wire on surface or in recess for loop earthing alongwith the existing surface/recess conduit/sub-main wiring/cables etc.as required

55) Supplying and drawing of 1.5 sqmm PVC sheathed copper conductor for loop earthing in the existing surface/recess steel/PVC conduit/PVC cassing & capping/wood batten alongwith others wires as required.

13) Advance maintenance free earthing of different dia,length and wall thickness copper/Galvanized bond electrode provding masonery enclosure with cover plate having locking arrangment and waterpipe, etc. ( but without charcoal or coke and salt ) complete as required.(a) Advance maintenance free earthing 48mm 2 meter length 3.2mm wall thickness copper bond with 2 bags back filling compound electrode (b) 40mm dia G.I pipe medium class-3mtrs (c) Funnel G.I nuts & through bolts, washer- set-1 (c) Locking arrangement,with hings cover plate No-1

LIGHTNING ARRESTOR (04) Providing & fixing of lightning conductor finial, made of copper five finger system with 85mm diameter 3mm thick base plate including holes etc completed.

(59)Providing & fixing of copper tape 20mmx3mm thick on parapet or surface of wallfor lightning conductor as required ( for vertical run )

(60)Providing & fixing of copper tape 20mmx3mm thick on parapet or surface of wallfor lightning conductor as required ( for horizontal run )

(61)Rivetting,sweating and soldering of copper/G.I tape ( with another copper/ G.I Tape base of the finial r any other metallic object ) as required

(65)Providing & fixing of testing joint made of 20mmx3mm thick copper strip 125mm long with 4 Nos of Tinned brass bolts,nuts,check nuts and spring washer etc.complete as required

A.FIRE HYDRANT(WET RISER) Fire Hydrant System: Supply (laying) of M.S milt steel black pipe C. Class including with welding cutting, erecting and all accessories like reducer, tie rod, band, tee, join, socket, elbow, flanged, rubber gasket, nut & bolt, anchor false nut, 1”G.I angle strip and also painting with red enamel paint and primer coat etc SITC of 80 mm dia. Pipe in R/m

SITC of Butter fly Valve complete with all accessories. IS mrkd SITC of Single headed landing Hydrant Valve (G.M) IS mrkd

SITC of RRL Hose pipe with M/F coupling (G.M) IS mrkd

SITC of short branch pipe (G.M)

SITC of Hose cabinet (750 x 600 x 250) 18 SWG thick M.S fabric

Overhead tanky(2000)ltr with all fitting accessories required

SITC of 2 way fire brigade inlet connection 63mm dia.Build in

B.FIRE ALARM SYSTEM SITC of 8 Zone Digitl Addresable microprocessor based fire alarm panel with 12v/15Ah battery and in build battery charger make:AGNI

SITC of photo electric multi detector with base plate. Make : Appolo/S.Sensor

SITC of manual call point with base plate. MAKE: AGNI.

SITC of hooter / sounder MAKE: AGNI

SITC of Wiring Laying of fire alarm system with 2cr x 1.5 sq mm copper cable, PVC PIPE wall mounted wih all accessories(Approx Estimate.After Completion)

FIRE EXTINGUISHER S/F of fire extinguisher type CO2 4.5 kg complete with all accessories.

S/F of fire extinguisher type ABC 4kg complete with all accessories.

S/F of fire extinguisher type mechanical foam 50L complete with all accessories

Sinage of fire exit and entry and other fire sign as per this project

S/F of fire bucket round bottom type,enamel painted white in side. Handle with mounting bracket rate to included fire bucket and stand fabricated

LUMPSUM - CENTAGE CHARGES Service connection for three phase

Northeast Consultancy Services

S.K. Construction

Brahmaputra Infrastructure Ltd.

BABIE CONSTRUCTION & CONSULTANCY SERVICES (BCCS)

VRC Constructions (I) Pvt. Ltd.

M/S BERIWAL CONSTRUCTIONS