REPAIR/MAINT TO FLOORING, ROOFING JOINERY AND CEILING INCLUDING SANITARY FITTINGS TO THE MANASBAL UNDER GE 970 EWS.

Amount

Taking down chowkhat with shutters (without taking off shutters from the frame) exc. 1.50 Sqm but n exc. 4 Sqm each complete and all as specified.

Taking down chowkhat with shutters (without taking off shutters from the frame) n exc. 1.50 Sqm each complete and all as specified.

Taking down shutter of any description exc. 1 Sqm and n exc. 2 Sqm each and refixing in same opening by making good complete and all as specified.

Taking down shutters of any description exceeding 1 Sqm and n exc 2 Sqm each complete and all as specified and directed.

S&F plain , solid , straight chowkhat and frames , wrought , framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints in 2nd class Hard wood complete all as specified.

M&L for Pressed steel frames for doors size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F factory made 35 mm thick 2nd class Hard Wood of plain framed panelled shutter ( two panels) with panels of timber flat on both sides feather edged), or of veneered particle board medium density or particle board with commercial face complete all as specified.

S&F 35mm th 2nd class soft wood for Glazed skeleton shutters for door open rebated and prepared to receive glass gauge etc. (with sash bars) edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc. size of members of shutter as specified in SSR Part- I section -8 clause 8.23 (b).

S&F 30mm th 2nd class soft wood for Glazed skeleton shutters for door open rebated and prepared to receive glass gauge etc. (with sash bars) edges of framing plain, chamfered or rounded , fitted with cuts and mitred beads for securing glass etc. size of members of shutter as specified in SSR Part- I section -8 clause 8.23 (b).

Factory made solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified.

S&F 200 mm long aluminium tower bolt, complete and all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy all as specified

S&F MS 100 mm size butt hinges medium wt. of cold rolled complete and all as specified.

S&F Butt hinges 100 mm long, stainless steel for PVC door shutter comlete all as specified.

Aluminium handles, cast type anodised150mm size complete all as specified

Aluminium handles, cast type anodised125mm size complete all as specified

S&F Mild steel pressed handles, oval type, stove enamelled black 150 mm size complete all as specified and directed all as specified

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, with glazing bars complete all as specified

Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, without glazing bars complete all as specified

Steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified.

S&F mild steel wire cloth galvanized 0.56mm normal dia of wire and average width of aperture 1.18mm complete and all as specified.

S&F in repairs mild steel wire cloth galvanized 0.56mm normal dia of wire and average width of aperture 1.18mm complete and all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm in each panes complete and all as specified.

S&F in repairs 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 Sqm in each pane including hacking out of glass panes complete and all as specified.

S&F MS Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for largegates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified

M&L for PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in hold fasts, complete all as specified.

S&F in repair 2nd class Hard Wood Plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads cross sectional area exc 13 sqcm and n exc 25 Sqcm complete all as specified.

S&F in repair 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work , fixed with screws all round complete all as specified.

S&F in repair 18/19 mm thick decorative block board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cup boards with 6mm thick teak wood lipping, fixed with screws all round complete all as specified.

S&F in repairs Continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps 30mm (when open).

Hasp and staple 150 mm size, safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate, fixed with screws in repair complete all as specified.

S&F in repair Mild steel 300mm long, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

Preparing new surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

Preparing new steel & iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide /zinc chrome primer complete all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises.

Demolition of brick work built in cement or cement lime mortar complete.

Brick work with sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete.

Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete.

Rendering 10 mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete.

Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished fair & even complete.

Rendering 15 mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces, mised with water proofing compound @ 3% by weight of cement, finished fair and even complete all as specified and directed.

Supply only water proofing compound, complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate in leveling course, benching etc, finished even & rough to receive cement mortar screed bed complete

M&L for Non skid ceramic joint free coloured tiles 300 x 300 x 7 to 8 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete.

Glazed ceramic coloured tiles 300 x 200 x 6 to 7 mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick screed bed or bedding layer in CM (1:4) complete all as specified.

Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper in approved colour/shade over a coat of chalk whiting primer after preparation of surfaces complete all specified.

Preparing new plastered or unplastered surfaces of ceiling and applying two coats of white wash complete all as specified.

Preparing new plastered or unplastered surfaces of wall and applying three coats of white wash incl preparation of surface complete all as specified.

S&F in repair harrison curtain rails of anodised alluminium alloy with fixing brackets, stops rollers etc complete all as specified.

S&F in repairs Anodised aluminium snap grid frame work for false ceiling all as specified size of Grid 605 x 605mm complete all as specified.

M & L in repairsGypsum10mm thick plaster of paris celing (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or over metal frame work and reinforced with GI wiremesh (Fillets, metal frame work and GI wire mesh paid separetely) complete all as specified.

Dismantling of corrugated or semi corrugated sheets as in roof coverings complete all as specified.

M&L in repairs for fixing 2nd class hardwood plain fillet, squar rectangular or triangular in section, clean swan, secured with nails or brad section exc 6 but not exc 13 Sqcm scantling complete all as specified.

M&L for preparation of new or old surfaces of wood or wood based materials of any description and girth, not otherwise described and treated with two coat of creosote oil complete all as specified.

M&L for Second class hard-wood in scantlings, clean sawn, timber fixed, complete all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self screws or 'J'/'L' hook complete all as specified.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwes or 'J'/'L' hook as specified complete all as specified.

S&F in repairs Door closer aluminium (extruded section body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

S&F in repairs brass Mortice lock, 4 levers, vertical type, size 100 mm of Make : Godrej or equivalent, complete all as specified.

Supply and fix in repairs steel rolling shutters ( thickness of laths 1.25 mm), push pull or manual type with out ball bearing including top cover, anchoring rod, hasp and staple, and one shop coat of primer; erected in position complete including taking down all as specified.

M/S LUCKY BUILDERS

M/S B S CONSTRUCTIONS

M/S MOHAMMAD YOUSUF RATHER