C/O toilet block near Comber mere bridge Nallaha ( SH C/O Civil work and WS and SI )( UNDER SHIMLA SMART CITY )

Amount

Earth work in excavation for structure in all depths as per drawing and technical specification for rural roads August 2004 clause 305.1 including setting out, construction of shoring abd bracing, removal of stumps and other deleterious materials and disposal in all leads and lift including dressing of sides and bottom and back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiseling and wedging out rock (where balsting is prohibited) all earth work in cutting/ excavation including rock excavation shall be carried out true to lines grades, side slopes, width , camber super elevation and level as shown on the drawings or as directed by the Engineer-in-charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified dimension or as directed by the Engineer-in-Charge. If the foundation of the structure is in an area with stagnant water or water is met with in the excavation due to spring seepage rain and other causes it shall be remove by suitable diversion bailing out or pumping as directed and the area of the foundation or embankment shall be kept dry. All the surplus excavated earth to be dumped at dumping site(dumping sites will be arranged by the contractor on his own cost).Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be dully compensated by him at his on cost in all cases. including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing form work with steel plates 3.15mm (Three point one five milimetre) thick welded with angle iron in frame 30x30x5mm (thirty into thirty into five milimetre)so as to give a fair finish i/c centring, shuttering, strutting and propping etc. with wooden battens and bailies in all heights or propping and centring, below supporting floor to ceiling not exceeding 4mtrs(four metres) and removal of the same for in situ- reinforced concrete and plain concrete work including carriage of materials in all leads and lifts as per the direction of Engineer-in- charge. (a)Foundation footing basis of columns etc. and mass concrete.

(b)Flat surfaces such as soffits of suspended floors, roofs, landing and the like. Floors etc. up to 200mm(two hundred milimetre) in thickness.

(c) Columns, pillars, posts and struts:- Square rectangular or polygonal in plan.

(d) Beams, cantilever, girders and lintels e) Sides and soffits of beams, beam haunchings, cantilvers, bressumers and lintels not exceeding 1 Mtr.(One metre) in depth in all heights from floor.

(e) Edges of slabs and breaks in floors and walls: Under 20 cm.(twenty centimetre) wide.

Providing and laying cement concrete 1:5: 10(One cement:five sand: ten graded stone aggregate 40mm (forty milimetre)nominal size)and curing complete including carriage of materials in all leads and lifts as per the direction of Engineer-in- charge. ( a) Foundation and plinth.

Providing and laying cement concrete 1:6: 12(One cement:six sand: twelve graded stone aggregate 40mm(forty milimetre) nominal size)and curing complete excluding cost of centring and shuttering including Mixing & Vibrating charges including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( a) Foundation and plinth.

Providing and laying cement concrete work 1:1½:3(One cement:One & half sand: three graded stone aggregate 20mm(twenty milimetre) nominal size) and curing complete excluding cost of form work including mixing & Vibrating charges and reinforcement for reinforced concrete work including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a)Foundation footings bases of columns and the like and mass concrete.

(b) Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level.

(c) Columns, pillars,posts and struts upto floor two level.

Providing mild steel/tor steel reinforcement for RCC work i/c bending, binding & placing in position including cost of binding wire complete up to all floor level/all heights including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( a) Tor steel.

Steel work welded in built up sections, trusses and framed work including cutting hoisting fixing in position and applying a priming coat of red lead paint including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm(One point six six milimetre) to two milimetre) thick in eaves board. Facia/ soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-Charge (Base members of steel work shall be measured & paid for separately) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing 0.60mm (zero point six zero milimetre)thick pre-painted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm dia metre with pre-painted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in super structure above plinth level including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) Cement Mortar 1:6(One cement:six sand) Second Class Bricks.

Half brick masonry in common burnt clay building bricks in Super structure above plinth level including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) Cement Mortar 1:4(One cement:four sand) Second Class Bricks.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.( i)2nd class deodar wood

Providing and fixing paneled glazed or paneled and glazed shutters for doors windows and clerestory windows including black enameled iron butt hinges with necessary screws including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.(a)40mm(forty milimetre) thick( i) Ist Class Deodar Wood.

Providing and fixing M.S. grills of required pattern in wooden frame of window etc. with M.S. flat square rounded bars with round headed bolt & nuts and screws including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a)Plain grill .

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)300x20mm (three hundred into twenty milimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)125mm (One hundred twenty five milimetre)

(ii) 75mm (Seventy five milimeter)

Providing and fixing aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a)150x10mm (One hundred fifty into ten milimetre)

(b) 200 x 10mm (two hundred into ten milimetre)

Providing 40x3 mm(forty into three milimetre) flat iron hold fast 40cm(forty centimetre) Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm.(thirty into ten into fifteen centimetre) (i) 1:3:6 (One cement : three sand: six graded stone aggregate 20mm(twenty milimetre) nominal size)

Providing and laying Duro stone vetrified tiles Nitco or equivalen(600x600mm) (six hundred into six hundred milimetre) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm(twelve milimetre) thick cement mortar 1:3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. (NITCO

Providing and laying Duro stone vetrified tiles Nitco or equivalen (300x300mmx 8mm)(three hundred into three hundred into eight milimetre) in grey/coloured of required shade in skirting risers of steps and dados on 12mm(twelve milimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying granite stone in walls 20mm(twenty milimetre) (average) thickness base of cement mortar 1:3 (one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) 20mm(twenty milimetre) thick

Cement concrete flooring 1:2:4(One cement:two sand:four graded stone agg.20mm(twenty milimetre) nominal size) laid in one layer finished with a floating coat of neat cement including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.(a)40mm(forty milimetre) thick.

6mm(six milimetre) thick cement plaster to ceiling in cement mortar 1:4(one cement:four sand) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

15mm (fifteen milimete)cement plaster in single coat on rough side of brick/ concrete /stone walls for interior plastering up to all floor level /heights i/c arises internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth in cement mortar 1:4(one cement;four sand) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

15mm(fifteen milimetre) cement plaster in single coats as pattern on cornior coat 10mm and finishing coat 5mm thick on fair side of brick masonry/stone masonry/concrete walls for interior/exterior/ plastering upto floor two level including arrises,internal /exterior rounded angles,chamfers and/or rounded angles not exceeding 80mm(eighty milimetre) in girth and finished even and smooth including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( a)Cement Mortar 1:4 (one cement:four sand).

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) Readymixed paint brushing wood primer pink

Painting two coats (excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering & stopping including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. a) With enamel paint other than white.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly leaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimetre) thick (unconsolidated) bed dry brick/stone aggregated 40mm(forty milimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing plinth protection 50mm (fifty milimetre) thick in cement concrete 1:3:6(One cement: three sand: six graded stone aggregate 20mm(twenty milimetre) nominal size) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) 20mm(twenty milimetre) nominal bore

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) 15mm (fifteen milimetre)nominal bore

Providing and fixing vitreous China wash down,water closet squatting pan (Indian type W.C pan) size 580mm (five hundred eighty milimetre)(Earth work, bed concrete, foot rest and trap to be measured and paid for separately) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Orrissa Pattern

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(one cement : one sand) (Seat and over to be measured and paid for separately)including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) Angle Indian Universal closet

Providing and fixing 10.00/12.50/15.00 litres(ten point zero/twelve point five zero/fifteen point zero litres) vitreous China low level flushing cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15mm (fifteen milimetre) nominal size brass ball valve with polythene float, C.P. Brass andle, unions and couplings for connections with inlet, outlet and overflow pipes, 40mm(forty milimetre) dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing vetreous china Hindware or equivlent in white shade flat back small No.50001 with auto cistern urinal bowl pattern including connecting the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.( i) Flat back type of size 430x260x350mm (Four hundred thirty into two hundred sixty into three hundred fifty milimetre).

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) Flat back(i) 550mm x400mm (five hundred fifty milimetre into four hundred milimetre).

Providing and fixing G.I./M.I Union of following sizes (where not included in the items including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) 32mm (thirty two milimetre)

Providing and fixing P.V.C. waste pipe flexible (Coil type)length not less that 800mm(eight hundred milimetre) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( i) 32mm(thirty two milimetre) dia

Providing and fixing C.P Brass bib tap with Capstan head including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a)15mm(fifteen milimetre) dia

Providing and fixing C.P Brass pillar tap with Capstan head including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (a) 15mm (fifteen milimetre) dia

Providing and fixng angle cock prismatic type with flange including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing PVC connection with brass unions including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. a) 450mm(four hundred fifty milimetre) length ( i) 15mm(fifteen milimetre) nominal bore.

Providing and fixing cast iron floor trap of self cleaning design with sand cast iron screwed down or hinged grating without vent arm complete including cost of cutting and making goods the walls and floors including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) 100mm One hundred ten milimetre) nominal diameter.

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) 100 mm One hundred ten milimetre)dia.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( i) 110mm (One hundred ten milimetre)dia

Providing and fixing PVC door T ISI marked including fixing with approved adhesive etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( i) 100mm (One hundred milimetre)dia

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)150 mm(One hundred fifty milimetre) dia.

Construction of man hole with RCC top slabe in 1 : 2 :4 ( One cement : two sand : four graded stone aggrigate ) 20 mm(twenty milimetre) nominal size foundation concreate 1:4:8 (One cement : four sand : eight graded stone aggrigate ) 40 mm (forty milimetre)nominal size , in side plastering 15 mm (fifteen milimetre) thik with cement motor 1:3 (One cement :three sand)finished with a floating coat of neat cement and making channels in cement concreate 1:2:4 (one cement : two sand :four graded stone aggrigate ) 20 mm(twenty milimetre) nominal size finished smooth complete including curing complete and testing the same :- In side size 800x800 mm and 500 mm(eight hundred into eight hundred milimetre and five hundred milimetre) deep including CI cover with frame light duty 455mm x 610 mm(four hundred fifty five milimetre) internal dimension total rate of cover and frame to be not less then 38 kg (thirty kilogram) with 200 mm(two hundred milimetre) thik walls of brick masonary in cement mortar 1:3(One cement three sand) including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and fixing PVC (finolex) Cowl including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i)110 mm (one hundreded and Ten) nominal size :-

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. ( i)1000 litres(One thousand litres) net capacity tank

Providing and fixing brass full way valve with wheel including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. a) 15mm(fifteen milimetre) nominal bore

Providing and fixing C.P. Zet for water closet (Uropean type) complete including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge. (i) 15mm(fifteen milimetre) nominal bore.

Ranjan Sood

RAJINDER SINGH VERMA