Kalidas Marg sthit Awas Sankhya-5A me deemak se shatigrast chaukhat/darwaze badalna evam deemak rodhi upchar karna, shatigrast wardrobe ki marammat karna va anya avashyak civil sambandhi karya.

Dismantling Doors, windows and clerestory window (Steel or Wood) shutter including chaukhat, architrave, holdfast etc. complete and stacking within 50 meters lead of area 3 sqm and below. DSR.No-15.12.1, (Rs-367.2/290.07)

Providing wood work in frame of doors, window, clerestory window and other frames, wrought framed and fixed in posotion with hold fast lugs or with dash fasteneres of reqiured dia & lenght (hold fast lugs or dash fastener shall be paid of separately (Second class teak wood, DSR-9.1.1, (Rs-142949.7/116311.02)

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. Door chowkhats each DSR-14.2.1, Rs-1782.55/1450.37

Treatment of Soil 'under Existing Floors Using chemical emulsion @ One Litres Per hole, 300 mm apart including drilling 12 mm holes and plugging with cement mortar 1 : 2 (1 cement 2 Coarse sand ) to match the exiting floor: with chlorpyriphos/ Lindane E.C. 20% with 1% Concentration. (DSR-2.35.3.1, Rs-310.05/244.92)

Providing and fixing Panelled or Panelled and Glazed Shutter for Door and windows and Clerestory window fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for seprately. all complete as per direction of engineer in charge. (Note- butt hinges and necessary screws shall be paid seprately) Secont class teak wood 35 mm thick shutter, DSR-9.5.1.1, (Rs-4111.95/3248.24)

Providing and fixing Glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood 35 mm thick DSR-9.9.1.1, (Rs-4940.2/3902.52)

Polishing in high gloss/matt finish Melamine clear Polish on wood work in required colour/ wooden shade texture with following process in the Sequence as detailed below. 1-The surface to be polished in rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2-Applying two coats of sealer with spray gun and allowing sufficient drying time for lst coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3-On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface futher smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface in furface allowed to dry for 12 hrs. 4- On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs than this dry surface is again fine wet rubbed smooth, which is futher allowed to dry for 12 hrs. the final melamine polish ia applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of engineer - in- charge. (Final coat to be done in 1 or 2 layers without gap of time.) DSR.N0-13.116), Rs-1360.45/1074.69

Providing and Fixing of Wall to Wall Wooden Almirah with 19mm thick Century Ply Board ISI marked lncluding Laminated Both Side 1 mm thick Sunmica Supirior quality Fixing with Glue and Nails etc S.S.Handle, S.S.Hinges Magnet. Lock etc. Complete work as Per Direction of Engineer in Charge. (Rs-13600)

Providing and placing on terrace ( at all floor levels ) Polyethylene Water Storage Tank. IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for intel, outlet and overflow pipes but without fittings and the base support for tank. DSR- 18.48) Rs-11/8.95)

Providing and fixing gun metal gate valve with C.I heel of approved quality (screwed end) 20 mm dia nominal bore, (As DSR-18.17.1A) Rs-539.95/426.54)