REPAIR AND MAINT TO CERTAIN ROADS AT JALIPA MIL STN UNDER GE (A) BARMER

Amount

M&L for repair to pot holes any depth area not exceeding 1.0 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths etc. cutting around edges to atleast 25 mm in depth, making good by applying tack coat VG-10 at 5 kg per 10 Sqm, putting in premix bituminous macadam well rammed and sealed with binder 9.8 kg per 10 sqm binded with 0.09 cum of stone chipping, 6.3 mm size and again well rammed (including supply of premix binder and sand) with 8 to 12 tonne power roller depth of pot holes not exc. 30mm complete all as specified and directed by Engineer-in-charge.

M&L for preparation of black top surfaces by brushing with wire brushes for removing cakedmud etc, sweping with broomes and finally fanning the cleaned surfaces with gunny bages to remove all loose dirt etc complete all as specified and directed by Engineer-in-charge.

M&L for preparing unsurfaced water bound macadam by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and directed by Engineer-in-charge.

M&L for applying evenly a priming/tack coat with paving bituminous primer VG -10 at 5.00 kg per 10 sqm with the help of mechanical sprayer complete all as specified and directed by Engineer-in-charge.

M&L for applying evenly a priming/tack coat with paving bituminous primer VG -10 at 2.50 kg per 10 sqm with the help of mechanical sprayer complete all as specified and directed by Engineer-in-charge.

M&L for premix bituminous macadam mixed in automatic hot mix plant with paving bitumen VG-40 with 4.5 % by weight of total mix laid by mechanical paver and rolled and compacted to required gradient and camber (consolidated thickness 75mm or less )by , 8-10 tonne capacity power road roller complete all as specified and directed by Engineer-in-charge.

M&L for laying and consoliding bituminous premix asphaltic semi dense concrete 30mm consolidted thickness with 5.5% binder content of paving bitumen VG-40 for 10 sqm area of road inc rolling and compacted to required camber and gradient 8 to 10 tone power rolled (rate shall be included as top finished similar to dense bituminous carpating) complete all as specified and directed by Engineer-in-charge.

M&L for preparing new or old bituminous surfaces of road and marking 2.0mm thick centre lines, stop lines, dashes, arrows etc and the like n exc 10cm wide on roads pavements except zebra crossing with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed by Engineer-in-charge.

M&L for one coat of synthatic enamel paint on old concrete surface including surface preparation of any description (Road side cement concrete kerb stone in ZABRA Pattern) complete all as specified and directed by Engineer-in-charge.

M&L for in repair for identification sign/cautionary mandatory and information sign board area exc 0.60 Sqm and n exc 1.20 Sqm with thickness not less than 3.0mm aluminium composite panel covered by encapsulated lens type retro reflective sheet (grade 3M type II diamond grade of make 3M/dark eye/SNI ) on both side with green base, including writing of necessary letter/symbols of reflective type fixed on and including stainless steel frame of size 25mmx25mm and hang on 50mm dia stainless steel pipe(fabrication work from SS-304 material) of height 2.4 mtr from ground level to top and post embeded in ground with PCC 1:3:6 TYPE C-2 using 40mm graded aggregate of size 45x45x45cm including necessary excavation and earth work and making plateform of size 150x45x30cm with PCC 1:2:4 using 20mm graded aggregate including necessary formwork and covering all exposed surfacess with black colour glazed ceramic tile (joint less) of size (600x300x7mm) / (450x300x7mm thick over and including 10mm thick backing coat in cement mortar(1:4) set and jointed in neat cement slurry and pointed to match the tiles complete all as specified and directed by Engineer-in-charge. Note :- The specifaction of board is held with GE(A) Barmer as sketch. The letters and symbols etc on both side shall be as per site requirement of user and as approved by GE. The size and font of wording/ arrow/ symbols as per direction of Engineer In-Charge.

M&L for repair and fixing stainless steel (Grade 304) railing made of hollow tubes,channels,platesetc.,including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-charge.

S&F in repair aluminium composite panel not less than 3.0 mm thick and including covered both side by encapsulated lens type retro reflective sheet (grade 3 M type II diamond grade of make 3M/dark eye/ SNI) green base, with and including all type and any size of writting letters and symbols of reflective type complete all as specified and directed by Engineer-in-charge.

S&F cat eye solar two side reflective type of metal body aluminium stud body alloy of size 110mm x 120mm x 20mm with PMMA strip lens reflector of suitable size fixed with and including stud of suitable size as per manufactures instructions complete all as specified and directed by Engr-in-charge.

S&F solar cat eye aluminum alloy shall (100% water proofing design according to IP 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono crystalline solar panel 2.4V/ 0.3 watt one NI-cd rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc complete all as specified and directed by Engineer-in-charge.

S&F metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed by Engineer-in-charge.

S&F in repair smart solar tubular dealineator of 1mtr height, model No DA-112 of material polycarbonate ABS and battery 1.2 V including embedding in PCC 1:2:4 (150x150x300mm) type B-1 complete all as specified and directed by Engineer-in-charge.

S&F in repair Outdoor Polycarbonate Convex Mirror size of 100 CM outer dia with 130 Degree + actual viewing angle, equipped with adjusting swivel and mounting bracket for infinite adjustment including embedding in PCC 1:2:4 size (450x450x600mm) type B1 including demolition of old PCC, mounted over 75mm dia stainless steel pole of appropriate height and adjustable arrangment complete all as specified and directed by Engineer-in-charge. Make : Road Star/Star Safety/Dark eye or equivalent as approved by GE.

Dismantaling Stone slabs and tiles laid dry or laid dry and pointed of any description or thickness in floors, aprons etc. complete all as specified and directed by Engineer-in-charge.

Demolition of concrete in ground floors and paving n exc 15cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-charge.

M&L for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and directed by Engineer-in-charge.

M&L for 300mmx300mmx10mm thick non-skid polka dots endura parking floor paver tiles with grey cement and pigment, over and including 15mm thick screed bed in CM (1:4), set jointed & pointed in neat cement slurry in floors complete all as specified and directed by Engineer-in-charge.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) as in sub base finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L for sand filling 25mm thick under floors or in foundations inc. watering and consolidation complete all as specified and directed by Engineer-in-charge.

M&L for 80 mm thickness machine pressed precast interlocking paver block any shape and size conforming to IS - 15658-2006 of M-40 grade with grey cement and no pigment complete all as specified and directed by Engineer-in-charge.

M&L for 100 mm thick cement concrete1:1.5:3 nominal Mix M-20 using 40mm graded crushed stone aggregate as in floor, sub base etc complete all as specified and directed by Engr-in-charge.

M&L for PCC 1:4:8 type D-2 (40mm graded crushed stone aggregate) as in foundation, filling, floor sub base and mass concrete complete all as specified and directed by Engineer-in-charge.

GEMRARAMCONTRACTOR (BID ID -3168729)

M/S LAXMAN CONSTRUCTION COMPANY (BID ID -3172969)

M/S HARIOM CONSTRUCTION COMPANY (BID ID -3168296)

M/s godara infratech and power industries (BID ID -3167866)