Eklavya Model Residential School (EMRS) at Ardaopur in Dima Hasao District under the Scheme Article 275(I) of the constitution of India during 2019-20 (Electrical Works, Sanitary Ware Fitting and Plumbing, HAVC Works, Fire Fighting Works, Extra Low V

Amount

Supplying, installation, testing & commissioning of following type wall mounted TPN/SPN distribution board of double door type, dust protected (IP-43), duly phosphatizes and powder painted design made out of 16 gauge MS sheet with supplying and fixing following accessories including Nutral bar, Earth bar, Din bar, detouchable gland plate, interconnections, earthing etc. as required. 12 WAY SPN MCB DB (LPDB)

6 WAY SPN MCB DB (LPDB)

4 WAY VTPN MCB DB (MLDB)

12 WAY VTPN MCB DB (MLDB)

12 WAY SPN MCB DB (PDB)

6 WAY TPN MCB DB (UPSDB/LPDB)

8 WAY SPN MCB DB (ELDB)

Point Wiring for Light Point, Fan point / Exhaust fan Points with 2 x 1.5 sq.mm + 1 x 1.5 sq.mm PVC insulated FRLS multistrand wire of 1100 volt grade in surface / recessed 25 mm. dia rigid PVC conduit including cost of rigid PVC Conduit, providing saddles etc for surface conduiting and/or cost of cutting & filling chases for consiled, 6A Moduler type Switch with Metal clad Switch board wiring complete as required. Short Point up to 3 meter Length

Medium Point up to 6 meter Length

Long Point up to 10 meter Length. (More than 10 meter length consider by the meter not by point)

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed 2 mm thick/ heavy rigid ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. Long point up to 10.00 metre. Length.

Long point up to 10.00 metre. Length. With 2 no. 6A switch & 2 no. 6A socket

Long point up to 10.00 metre. Length. With 3 no. 6A switch & 3 no. 6A socket

NOTE: Switch and sockets are internally connected Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed conduit wiring system including and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. mark with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) Long point up to 10.00 metre. Length.

TUBE LIGHT- WIPRO CAT. NO.-LL20-221-XXX-65-NE3

CEILING SURFACE LIGHT_11W WIPRO CAT. NO.-LL20-111-XXX-65NE3

FALSE CEILING LIGHT_15W WIPRO CAT. NO. -LD80-131-XXX-60-XX

WALL MOUNTED LIGHT WIPRO CAT. NO. -LW01-101-XXX-60-XX

TUBE LIGHT- HANGING WIPRO CAT. NO. -WIO921208 + LL13-181-650

STREET LIGHT WITH POLE

SP 30A/30A ACCL

AC STARTER-20A

Premium model 4-Star 1200 mm Sweep Ceiling FAN (ORIENT PSPO make / Usha make/ CROMPTON make/ Havells/ ATC/ V GAURD make)

Supplying, installation, testing & commissioning of following sizes of Exhaust fans suitable for 300 mm. dia. 230volt, 50Hz 1400 RPM single phase A/C supply and complete with all standard accessories such as motors blades and louvers, shutters etc.

Providing & fixing of GI Ladder type Cable Tray suspended from the ceiling for Power Cabling of following sizes complete as required including 10mm dia tie rod, 25 X 25 X 6 ISMA, 10 mm dia bullet type anchor fustner, cutting the wall etc. as required. 50 mm x 450 mm x 50 mm X 2.15 mm Thick

50 mm x 300mm x 50 mm X 2.15 mm Thick

50 mm x 150 mm x 50 mm X 2.15 mm Thick

Fabrication supply and fixing of angle / channel iron brackets / supports of adequate size to support the cables and panels in existing cable trenches including fixing clamps and hard ware metering good the damage etc. as required .( Cable trenches shall be in the scope of building contractor). Contractor should supply the Shop Drawings of Hanging arrangement of Cable Tray.

Supplying, Laying, testing & commissioning of the following sizes of XLPE insulated, multistand Al. & Cu. Conductor armoured cables of 1.1KV grade on the surface of wall or on existing cable trays or Under Ground cable trench complete with fixing hardware etc. as required. 3.5 C x 300 Sq. mm Al. Cable (A2XFY)

3.5 C x 185 Sq. mm Al. Cable (A2XFY)

3.5 C x 70 Sq. mm Al. Cable (A2XFY)

50.00 Sq. mm.3 & 1/2 Core armoured U.G. cable

3.5 C x 25 Sq. mm Al. Cable (A2XFY)

4 C x 16 Sq. mm Al. Cable (A2XWY)

4 C x 10 Sq. mm Al. Cable (A2XWY)

3 C x 4 Sq. mm CU. Cable

Suppling, making, testing & commissioning of end termination with brass mettalic double compression glands suitable for the following sizes of XCPE Al. & Cu. conductor arnoured cables including proper sizes of Al. or Cu.thimbles etc. as required. 3.5 C x 300 Sq. mm Al. Cable (A2XFY)

3.5 C x 185 Sq. mm Al. Cable (A2XFY)

3.5 C x 70 Sq. mm Al. Cable (A2XFY)

3.5 C x 50 Sq. mm Al. Cable (A2XFY)

3.5 C x 25 Sq. mm Al. Cable (A2XFY)

4 C x 16 Sq. mm Al. Cable (A2XWY)

4 C x 10 Sq. mm Al. Cable (A2XWY)

3 C x 4 Sq. mm CU. Cable

Supply, Installation, testing and commissioning of earth electrode as per IS 3043-1987. The rate shall be for complete work like excavation, back filling with salt and charcoal, ramming and consolidation , brick work , cast iron heavy duty cover slab etc. All earth station to be treated suitably to obtain individual earth resistance with in 1 ohms as per requirements of local authorities. This shall also have chamber with funnel arrangement for watering. A) Providing, Making, Testing & Commissioning of earth pits including the cost of 600mm x600mm x 3 mm thick copper plate electrodes, 50mm dia pipe , CI funnel with wiremesh, GI watering pipe, charcoal salt all earth works masonary enclosure with CI frame &cover plate having locking arrangement complete as per IS 3043:1987. Transformer Neutral

DG Nutral

UPS Nutral

B) Providing, Making, Testing & Commissioning of earth pits including the cost of 600mm x600mm x 6 mm thick GI plate electrodes, 50mm dia pipe , CI funnel with wiremesh, GI watering pipe, charcoal salt all earth works masonary enclosure with CI frame &cover plate having locking arrangement complete as per IS 3043:1987. HT Substation, HT Breaker, Transformer Body

DG Body

Panel & BDs

C) Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement 300 mmx300 mmx6 mm hinged cover C.I. earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

LIGHTENING ARRESTER Supply, fitting & fixing of Lighting Finial Arrestor made of 25 mm dia 300 mm long solid G.I. tube having 85 mm dia. single prong at top and 3 mm base plate at bottom complete with fitting & fixing with G.I. nuts & bolts on roof, RCC slab, top of column etc. as specified and directed by the deptt.

Supply and fixing of G.I. strip of size 32mm x 6 mm on parapet of wall for horizantal runs and on wall for vartical runs for horizontal termination lighting arrestor system i/c all fixing hardware soldering sweating of joints complete as required.

EARTHING STRIPS Supplying and laying of the following earthing clamps saddles and fixing bolts in ground including the cost of digging and backfilling with sand and protection as required complete to comply with IS:3043:1987. Rate shall be inclusive of anti-scate washer, spacer clamp for main earth flat, suitable clamping with Cu flats for earth wires etc including terminal crimping type sockets bolts and washeres, etc required for the complete job. a) NO 8 SWG Cu Wire

b) 25 x 4 Cu Strip for UPS, OT & ICUs

c) 30 x 5Cu Strip for Trafo & DG Nutral

d) 32 x 6 G.I Strip for Trafo, DG Body and Pit to Earth Bus

e) 25 x 5 GI Strip for Panels & DB

Out door Oil type 630 KVA, 11kV / 0.433kV Pole Mounted Substation SUBSTATION Supply, Installation, Testing & Commissioning of pole mounted ,12KV,500 KVA , Vector DYN11, Copper wound transformer as per technical specification,SLD and relevant IS and ASEB standard It should comprises of - i) 400 KVA, 11/0.433 KV, DYN-11, Copper wound Transformer - 1 No. ii) 10.00 Mtr length seamless steel tubuler pole type 410 SP 43 as per IS-2713 (Part III) iii) 11KV DO switch - 1 set iv) MS Chaneel of size 100 x50x 6mm x 2.2 mtr - 6 nos. v) 11 KV Lighting arrestor - 1set vi) 11 KV Pin Insulator - 1 set vii) LT Cross arm - 6 nos. viii) 100 mm dia GI pipe for earthing - 6 nos. ix) 11 KV Disk insulator - 12 nos. x) Hardware fitting for above disk insulator xi) Gaang Operated switch - 1set xii) 11 KV Danger board - 2 nos. xiii) 6 SWG Copper wire-30KG xiv) Pole Clamp - 12 nos. xv) Cable termination Box, MS Nuts & Bolts, etc all complete The rate shall include the following job : SITC of the equipment Testing of equipment as per specification and relevant IS at Manufacturer's Factory. Delivery at site. Unloading at site store. Shifting from site store to substation room including removing the packing. Assembling the equipment if required. Testing of breaker including testing of tripping mechanism, setting of all relays etc. Supply of necessary spares required for commissioning. System study and protection co-ordination setting for HV as required. To Take approval from statutory body if required. To prepare submission drawing and to take approval of consultant at each stage. To prepare & submit as-built drawing and handing over document to end user. xvi) CT & PT combined metering equipment as required 630 KVA,50Hz.11/0.433 KV. Oil filled transformer with Off Circuit tap change.

EXTERNAL ELECTRICAL-DG SETS DOE and other statutory approval of the whole electrical installation will be in the scope of vendor. No extra payment will be made on account of this 1. The DG sets and system offered shall comply to "Environmental Regulations on Engines for Generator Set Application and Generator Sets" issued by Central Pollution Control Board in February 2004 and latest amendments as applicable and other statutory regulation as applicable. 2. The size of exhaust/fuel pipes, ratings of Pumps etc shall be suitable for the DG sets specified and sizes / ratings given are indicative only. These shall be suitable for the DG sets as required and no extra payment shall be made for such changes. Supply, Installation, testing and commissioning of 3 phase 415 volts 50 cycle per second 1500 rpm Acoustic enclosed type Radiater cooled Diesel Generator Sets with AMF Panel as below. The sets shall be suitable for delivering the rated output at 0.8 pf for continuous round the clock operation without interruption for 365 day in a year excepting for scheduled maintenance check. The engine shall include flywheel with guard, air cleaner, blower fan, ventillation louvers, ventilation fans, suction louvers, fuel pump, class A1 electronic governor, electronic fuel injection system, fuel filter, lub oil filter & pump, battery charger, 24 volt batteries of compatible capacity with battery stand and instrument panel comprising of switch with key etc. as required. The alternator shall be separately excited with PMG and continuously rated for DG set ratings suitable for 3 phase 415 volts 50 cycles, 4 wire system and shall be provided with static excitation unit, Alternator insulation shall be class F with temperature rise limited to Class B suitable to withstand tropicalconditions and shall generally comply with BS 5000 and IS 4722. This should be suitable for AMF, syncronisation and auto load management. The overload capacity shall be not be less than 110% of rated capacity for 1 hour in every 12 hours The DG set shall be mounted on a fabricated rigid common base frame with GERB make resilient anti-vibration mountings to provide 98% vibration isolation. The DG set shall include all accessories, fittings, flexible bellows, instruments & standard tool kit complete as per specifications and as required. The quoted rates shall include cost of providing free maintenance as per specification for a period of 1 year from the date of handing over. Including 990 litre capacity day fuel tank as per specifications with all required arrangement. Including the Sutiable AMF Panel as per SLD Capacity -62.5 kVA Make - GREAVES/CUMMINS/VOLVO PENTA Cooling - Water cooled Aspiration - Tourbocharged and after cooled Starting System - 24V ESE Voltage Regulation - ± 1 % Insulation Class- H Enclouser - IP 23 Excitation : Brushless with AVR Control Battery Capacity: 12V with suitable AH AMF Panel Alternator Voltage - 415 V AC, Frequency - 50Hz No. of Pahse - 3, 4 Wire system 62.5 KVA Silent DG set

Supplying ,installation, testing & commissioning of Hi-Path 1120 Digital Communication System equipped with the following: 6 P&T Ports - 16 Extension Ports Auto Call Back , Built-in FAX/DID Built in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non- Block ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Distribution Box 50 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Dedicated EPABX Earthing for trouble free operation ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of UROSET 2005 Analog Hand set ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Constant Voltage Transformer 500 VA ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying ,installation, testing & commissioning of 5 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying ,installation, testing & commissioning of 20 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Wiring for Co - axial Jelly Flooded (Unarmoured) (FINOLEX /RR KABEL /NICCO / ANCHOR make) cable in existing surface conduit wiring system including connection etc as required. Co - axial Jelly Flooded (Unarmoured) RG 6 (Copper)

Supply and Installation of 8-way splitters in die cast Al.casing

Supply and Installation of 6-way splitters in die cast Al.casing

Supply and Installation of 4-way splitters in die cast Al.casing

PLUMBING Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) (a) With 'P' trap

(b) With 'S' trap

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) (i)Economy Single Flush (Cat No.C8090/C8055)

Supplying, fitting and fixing 600mm long CP towel rail of Agmeco make complete as specified and directed.

Supplying, fitting and fixing CP towel ring of Agmeco make complete as specified and directed.

Supplying, fitting and fixing soap dish of Agmeco make complete as specified and directed. (ii) Soap dish pears (Cat.No.TR-0662) / Soap dish square (Cat.No.TR-0663)

Supplying, fitting and fixing CP bib cock 15mm dia of approved brand directed specified. (G.I & C.P. pipes will be measured separately) Agmeco brand (v) Bib Cock Two way with Flange CAT No.CC 00203/CAT No.CN 00203

Supplying, fitting and fixing CP health faucet shower with 1mtr PVC flexible tube and ABS wall bracket of Agmeco make as directed and specified.

Wash basin vitreous china flat back wash basin of size 550mm X 400mm of Hind ware with C.I./MS brackets, 32mm CP brass waste coupler of standard pattern, CP stop cock, C.P. brass chain with plug, PVC flexible pipe, PVC waste pipe including painting of fittings, brackets, cutting and macking good the walls whenever required. White vitreous china flat back wash basin of size 550 mm X 400 mm

Supplying, fitting and fixing Chrome Plated (C.P.) basin mixer complete as directed. Crabtree Frattini make (For VIP use. Prior approval of Chief Engineer PWD (Bldg) must be taken before use) a) Florence. i)Central hole basin mixer without pop-up Cat No.21051 for wash basin

Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately Overall size 610mm x 460mm x 255mm and bowl size of 510mm x 460mm x 254

Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified. (a) Jaquar Make, (i) 32mm (HT/FT) (Cat.No.ALD-705 / 709)

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) Jaquar (iii) 15mm dia( Angular stop cock with long thread )

Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. Agmeco (classic) FLAT

Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) Agmeco brand a) Sink cock casted swivel spout

Providing fitting and fixing Mirror with plastic frame of size 500x400mm complete as directed and specified.

Providing fitting and fixing Glass Shelf complete as directed and specified. (i) Agmeco make, (e) Dolfee (Cat.No.DE-00104)

Providing, fitting and fixing C.P. bottle trap Cera make, 6" for basin etc. complete as directed and specified. (i) Bottle trap 150 mm (6”) (Cat.No.104)

Supplying, fitting and fixing C.P. bib cock of 15mm dia of approved brand as specified and directed. Agmeco make Bib cock with wall flanged Cat. No. - CC 00201/ Cat. No. CN 00201

Supplying, fitting and fixing Chromium plated Stop Cock of approved brand and size as mentioned below as directed and specified. Agmeco brand Concealed Stop Cock

Supplying and fitting fixing polymer pillar cock of Polymer Prayag make (15mm) dia as directed.

Supplying, fitting and fixing C.P shower with bend 15mm dia of Agmeco make with wall flanged as directed. Essco/ Lauret/Jaquar

Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. Agmeco make d) Wall mixer with bend Cat No.1122

Providing and fixing white vitreous china flat back type lipped front urinal basin (of 610 x 310 x 480mm) of Parryware make with CI/MS brackets, with automatic flushing cistern of similar colour and standard flush pipe and CP brass spreader with brass spreader with brass unions, etc. complete including painting of fittings and rackets, cutting and making good the wall and floors whenever required.White

Supplying, fiting and fixing automatic flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) Auto Cistern 10 litre (Cat. No.C61002)

Providing, fitting and fixing Chrome Plated TOILET PAPER holder complete as directed and specified. (b) Agmeco make (i) Cubin (Cat. No.CB-00001)

Providing and fixing chorinated polyvinyle chloride (CPVC) pipes, heaving thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipe. Concealed work including cutting chases and making good the wall etc. 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

Exposed or in trenches 25 mm nominal outer dia pipe

32 mm nominal outer dia pipe

40 mm nominal outer dia pipe

50 mm nominal outer dia pipe

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed. A) G.I. pipe with GI fittings a) TATA / SAIL (Medium) 80mm diameter (Roof Ring)

50mm diameter

40mm diameter

32mm diameter

25mm diameter

B)Upvc pipe with uPVC fittings(Using uPVC high pressure pipe)(Using SUPREME/PRINCE/sfmc/FUSION brand pipe) 160 mm diameter S.W. pipe

200 mm diameter S.W. pipe

Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed. a) 40mm dia

b) 32 mm dia.

c) 25 mm dia.

d) 20 mm dia.

e) 15 mm dia.

Supplying fitting fixing of PVC pipes of 6 Kg/ cm 2 (Supreme/ Prince) or other ISI approved including joining, fitting and fixing with clamps etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surfaces or in trenches. 110mm dia (Internal, Shaft area)

75 mm dia (Internal,vent)

160mm dia (RWP)

110mm dia (RWP)

Supplying fitting fixing 87.5 degree PVC bend of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surface 110mm dia

110mm dia

Supplying fitting fixing 45 degree PVC bend of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surface 110mm dia

Concealed by chiselling or breaking brick wall/ C.C/ R.C.C. and making good to the damages. Concealed by chiseling or breaking brick wall/ C.C/ R.C.C. and making good to the damages. 110mm dia

Supplying fitting fixing PVC single tee with door of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surface 110 mm dia

Concealed by chiselling or breaking brick wall/ C.C/ R.C.C. and making good to the damages. 110mm dia

Supplying fitting fixing PVC cross 'T' plain of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surface 110 x 110 mm dia

Supplying fitting fixing PVC double 'Y' plain of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. In exposed surface 110 x 100 mm dia

Supplying fitting fixing PVC trap (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. 110 mm dia

Providing, fitting and fixing C.P. grating to the floors complete as directed and specified. 110 mm dia

50mm dia grating

Providing, fitting and fixing 110mm dia PVC cowel of ISI make complete as directed and specified.

Supplying, fitting and fixing supreme brand or similar approved P.V.C. pipes of following sizes with all necessary fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fittings, clamps etc. complete at all levels including below G.L. as directed and specified. Exposed or in trenches 63 mm nominal bore

50 mm nominal bore

40 mm nominal bore

32 mm nominal bore

Constructing Inspection Pit inside measurement 450 x 450 x 450mm flush with 100mm dia pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement morter in proportion 1:4 finished with 13mm plaster in proportion 1:2 in side wall and floor. 450mm x 450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Providing, fitting and fixing (600 x 600mm) 90mm thick C.I manhole cover and frame of 25 kg weight as directed and specified.

Providing, fitting and fixing (450 x 450mm) 90mm thick C.I manhole cover and frame of 38 kg weight as directed and specified.

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes 2000 Lt capacity water tank

1000 Lt capacity water tank

Supplying, fitting and fixing Geyser 10ltrs capacity Venus or approved make.

Supply, installation, testing & commissioning of wall mounted type MICROPROSSER BASED air cooled split air conditioning units each complete with full inverter compressor, controls, air cooled condenser, condenser fan unit, integral refrigerant copper piping duly insulated with adequate thickness of Arma Flex insulated material covered with Aluminium Foil and accessories such as refrigerant shutoff valves at compressor / compressors and liquid refrigerant outlet if required, filter dryer, insulated copper piping, cabling, cable tray and tray supports between package unit and air cooled condenser, MS epoxy painted stand for condensor unit, condensate drain piping, vibration isolation pads, including all copper, power / control wiring, and earthing, external wiring, between AC unit starters, unit & condensing units, all system controls-safety, capacity. The unit shall be suitable for 415 ± 10 % volts, 50 Hz, 3 phase AC supply and IP55 Protection. The unit shall be minimum 3 star rated. Make - Hitachi / Diakin 1.5 TR Hi-Wall Split Unit

2.0 TR Hi-Wall Split Unit

For Outdoor unit supporting bracket & Cage made from angle iron/ M.S. Flat duly painted.

Refrigerant copper piping duly insulated with adequate thickness of Arma Flex insulated material interconnecting indoor & outdoor unit including supply of control cable for package unit. (Beyond 3mtr will be measurable)

Condensate Drain Piping : Providing and fixing in position the following pipes cut to required lengths and necessary fittings with insulation.20 mm dia. PVC flexible pipe.

Toilet & Pantry / Kitchen Ventilation System: SITC of Propelar type Exhaust Fan 600 cfm 10 mm SP complete assembly with motor electrical wiring, etc. for toilet ventilation

SITC of Propelar type Exhaust Fan 150 cfm 5 mm SP complete assembly with motor electrical wiring, etc. for toilet ventilation

FIRE FIGHTING FIRE EXTINGUISHERS Providing & Fixing of fire extinguishers with necessary accessories, stand, trolley, etc. Supply, Installation, Fixing of ABC Stored Pressure Fire Extinguisher with built – In pressure Gauge to know the Ready ness of the Extinguisher Squeeze Grip Handle As per IS:13849 with ISI mark (05 kg capacity) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Installation, Fixing of CARBON DIOXIDE Fire Extinguisher confirming to IS: 2878 with ISI Mark, (Extinguisher will be TROLLEY MOUNTED)(2KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

Supply, Installation, Fixing of DRY CHEMICAL POWDER Fire Extinguisher confirming to IS: 2171 with ISI mark and CO2 cartridge will be confirming to IS: 4947 with ISI mark, Powder will be confirming to IS: 4308 with ISI Mark (5 KG) BRAND : FIRESTOP / FIREND / FIRE SHIELD

FIRE FIGHTING RISER & INTERNAL HYDRANT SYSTEM Providing,Fixing,Testing & Commissioning of Mild Steel Black Pipe (IS:1239part-I) Heavy class including cutting, screwing, welding etc. and providing all fittings viz forged steel screwed fitting upto 50mm dia and bolt welded above 50mm dia flanges, bends, tees, reducers, elbow, clamps, hangers etc including cutting holes and chases in brick or RCC walls/ slabs and making good the same to the approval of Engineer-in-charge/ consultant complete including painting with one coat of primer and two or more coats of synthetic enamel paint of approved make and shade including steel work complete as required. (Make:TATA/JINDAL/NEZONE) 200mm ( 6 mm thk IS 3589)

150 mm (Wet Risers - HYDRANT+ ROOF RING)

80 mm (For Landing Valve Connection)

25 mm (For Hose Reel Drum Connection)

Supplying & Fixing,cast iron body Butterfly Valves with matching flanges, rubber insertion, nuts, bolts and washer etc (IS:13095) of following size complete as reqd. (MAKE : KOLEY/KALPANA/AUDCO) Size : 200 mm

25 mm (For Air Realease Valve)

Providing,Fixing, testing &Commissioning of Single Headed Gun Metal ISI Marked oblique pattern Hydrant Landing Valve with 80 mm dia, flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain, twist release lug and all accessories as per IS:5290-19833 (Type-'A') and specifications complete as reequired . (MAKE:ESSEL/WINCO/NEWAGE) 63 mm Single headed Hydrant

Providing RRL Hose with ISI Marked (IS:636) 63 mm dia X15 M long complete with instantaneous type Gun Metal 3 mm dia ISI Marked male & female couplings (IS:903) bound & riveted to hose pipes with copper rivets and copper wire complete as reqd. ( MAKE: NIRMAL RUBBER/NEWAGE) 63 mm RRL Hose 15mtr.length.

Providing & fixing of weather proof hose cabinets fabricated from 16 S.W.G. M.S. Sheet with centre opening full front glass door and locking arrangement, suitable to accommodate one landing valve (Yard Hydrant ), 2nos.15M long hoses and 1 no. Branch pipe with nozzle . The cabinet shall be painted with one coat of primer and 2 or more coats of synthetic enamel paint of approved make & shade and shall be suitably mounted on a raised masonry platform complete as reqd.(Make:self Fabricated) Hose Cabinet (900x600x450)

Providing controlled percolating (C.P.) hose ISI Marked (IS:8423) 63 mm dia X 15 M long complete with instantaneous type Gun Metal 63 mm dia ISI Marked male & female couplings (IS:903) bound & riveted to hose pipes with copper rivets and copper wire complete as required. (MAKE: NIRMAL RUBBER/NEWAGE) Hose reel having 15 mtr. Length

Providing ,Fixing ,Testing & Commissioning of air Release Valve 25 mm Air Release Valve

Providing & Fixing of Gun Metal 63 mm dia Short Branch Pipe with 20 mm dia nozzle, ISI marked (IS:903) complete as required. (Make: ESSEL/WINCO/NEWAGE). GM Branch Pipe

Supplying & Fixing Cast iron body Non Return valves complete with matching flanges, rubber insertion, nuts, bolts and washer etc. (IS:5312) of following sizes complete as reqd. (Make:Koley/Kalpana/Audco) 150 NB

Providing, erection testing, Commissioning of Cast Iron Foot Valve / Y- TYPE or POT TYPE Stainer confirming to IS:4038/1538 complete with flanges, nuts, bolts and washer etc as required 200 mm

Providing ,erection,Testing & Commissioning of Pressure Switch (MAKE:INDFOSS) Pressure Switch

Providing,erection testing & commissioning of pressure gauge 100 mm dia. (0-10Kg/cm2)

Supplying, installing, testing and commissioning of centrifugal mono block/vertical multi stage type Boosting Pump-Motor having bronze / SS impeller with discharge 2280 lpm against 55 mtr. head with 3 phase, 415 V, 50 Hz motor having 2900 RPM, as per site conditions and instructions of site engineer-in-charge including proper fixing, The electrical motor for the pump should comply as per Specification. The scope shall also include necessary coupling, coupling guard, base frame, foundation bolts, RCC foundation, etc. complete Pump - Motor: Discharge: 2280 LPM, Head: 55 mtr.

MCC for Fire Pumps : Design, manufacture, supply ,installation, testing and commissioning of following Fire panel suitable for 415V, 3 phase, 4 wire, 50 hz power distribution system. The panel should be indoor, free standing, floor mounting, sheet metal clad, Cubicle, dead front, dust and vermin proof, compartmentalized design fabricated out of 14 SWG sheet steel complete with Cu busbars, a separate earth bus bar to be provided through out the length of the panel. The incoming and outgoing feeders shall be accommodated in a modular multitier arrangement, adequate size cable alley, painting, earthing numbering, damper plate etc. as required as per specifications and drawings and as per local Fire Authority requirement As per Attached SLD

Test assembly SITC of electronic type water level indicator with LED panel, with probe & all control wiring to operate the system automatic/manual & shall prevent the pump from dry running

Charges for liasoning with CFO and getting all approvals and permissions & NOC 's required for fire fighting at various stages & after completion of the project. (All official and receipted payments would be submitted and Re-imbursed) Taking approval /NOC form CFO

Supply, installation, testing & commissioning of Rubber Bellows on discharge side of pump conforming to EJMA with all hardwares, companion flanges & gaskets, etc. Size : 200 mm

Size : 150 mm

Supply, Installation, Testing, Commission of Intelligent Fire Alarm Control Panel 2 Loop card inbuild,198 Addressable points per loop, total addressable devices 396, Integrated PSU with Battery Charger, Requires network card additionally for networking

Supply, Installation, Testing, Commission of Loop card for Addressable Panels make- MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, Installation, Testing, Commission of Addressable Semi Flush Mounting Resettable (NonBreaking Glass) MCP, Supplied with Special Reset Tool BRAND : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, Installation, Testing, Commission of Addressable Wall Mounting Sounder / Hooter Cum Strobe Brand : MORLEY/FIRELITE/Apollo or equivalent as approved by the Deptt.)

Supply, installation, testing & commissioning of intelligent plug in photo electric Smoke Detectors having features like integral communication, dual LED for 360° viewing angle, walk test with address display etc. UL / LPCB approved, make : HONEYWELL, MORLEY IAS, Model : MI - PSE or equivalent as approved by the Deptt.

Supply, installation, testing & commissioning of Control Module.UL / LPCB approved, make - Honeywell , MORLEY IAS, or equivalent as approved by the Deptt.) with housing box

Supply & fixing of 2X1.5sq. mm. PVC insulated copper Armoured Cable on surface/ recess/ above false ceiling etc. as required. (ISI marked) )

CCTV Supplying installation testing and commissioning of - 1/3" Super HAD colour CCD, Built-in auto iris fixed lens : 3mm, 600TV lines Dome Camera, Min. illumination of [email protected], 12V DC (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of - 1/3" Super HAD CCD, 600 TVL (Colour) / 700 TVL (B/W) IR Dome Camera, Min Illumination 0 Lux (IR LED on), IR Distance 20 m, 3.6 x V/F Lens (2.8 ~ 10 mm), True Day & Night (ICR), 12 VDC (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of - Weatherproof IR Camera, 600 TVL (Colour) / 700 TVL (B/W), 1/3" Super HAD CCD, Min Illumination 0 Lux (IR LED on), IR Distance 50 M, Built in V/F lens 2.8 ~ 10 mm, True Day & Night (ICR), IP 66 (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of - 16 Chanel CIF Real Time DVR,upto 400 (PAL) fps recording rate , Max 4 internal HDD (HDD x 4) , 4 Audio Inputs, 1 Channel Audio Output , DVR-RW (SAMSUNG or equivalent HONEYWELL/PANASONIC make)

Supplying installation testing and commissioning of Hard Disk For DVR 1 TB (SEAGATE / WD make)

Supplying installation testing and commissioning of Power Supply SMPS Based 12V For 16 Camera (PROTEK make)

Supplying installation testing and commissioning of 22" LCD TFT Screen (SAMSUNG / ball / LG / MITASHI make)

Supplying installation testing and commissioning of UPS 1 KVA for Back Up (ball / ELNOVA / APC make)

Supplying installation testing of UTP CAT6 Cable without PVC conduit

Supplying installation testing and commissioning of 24 port L2 PoE Switch

Supplying ,installation, testing & commissioning of Hi-Path 1150 Digital Communication System equipped with the following: 8 P&T Ports - 46 Extension Ports ( non upgradeable Auto Call Back Built-in FAX/DID Built in Voice Guided Direct inward Dialling 3 party Conference In-built Caller ID 100% Non-Block. Supports PRI/BRI ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Distribution Box 50 pairs with Krones ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of Dedicated EPABX Earthing for trouble free operation ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of UROSET 2005 Analog Hand set ( SIEMENS or equivalent as approved by the Deptt.)

Supplying ,installation, testing & commissioning of 2 pair Unarmoured Telephone Cable through existing conduit in surface/ recess system.

Supplying with fitting and fixing of RJ-11 Telephone jack , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supply, installation testing and commissioning of following LAN networks equipments. Patch Cord Cat 6 UTP Gray 2m - Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

BACK BOX -(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

DIGILINKL/ LEGRAND OR equivalent 24 Port 10/100/1000Mbps Layer 3 switch with 2 x 10G Uplink slots and 2 x High Speed stacking transceiver cable slots

6U Rack Loaded SCHNEIDER/ LEGRAND or equivalent

Supplying with fitting and fixing of CAT 6 RJ-45 Computer jack in one module , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

CABLE TV Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Co - axial Jelly Flooded (Unarmoured) RG 6 (Copper)

Supply and Installation of 8-way splitters in die cast Al.casing

Supply and Installation of 6-way splitters in die cast Al.casing

Supply and Installation of 4-way splitters in die cast Al.casing

PUBLIC ADDRESS AND AUDIO SYSTEM Supplying installation, testing, programming and commissioning of Audio equipment, Dual Channel Power Amplifier, 1200W @ 2 ohm, 775W @ 4 ohm, 440W @ 8 ohm per channel

Supplying installation, testing, programming and commissioning of Audio equipment, Rack‐mounted panel with four auto former to provide impedance matching between an amplifier output and constant voltage loud speakers

Supplying installation, testing, programming and commissioning of Audio equipment, Gooseneck or equivalent as approved by the Depts. microphone - 30/ 50 cm hypercardiod/ Cardioids gooseneck (or equivalent as approved by the Deptt.) microphone without base

Supplying installation of Projector ceiling Mount

Supplying, including Installation , Testing , Commissioning & Programming of In ceiling speaker as per Technical specification In ceiling speaker , Driver size - 8 inch , Frequency Range (-10 dB): 50 Hz – 16 kHz ; Coverage : 90° conical ; Sensitivity (2.83V@ 1m) : 97dB(1kHz-8kHz) ; Nominal Driver Impedance: 8 Ohms ; Driver Power Capacity: 25 watt ; 70V/100V Transformer Taps: 6 W, 3 W, 1.5 W, (0.75 W at 70 V only)

Supplying installation, testing, programming and commissioning of Audio equipment, High flexible Speaker cable for power amplifiers up to 1000 watts , Jacket - PVC, ø 0.32 in, black Conductor - Stranded bare copper cables, 140x35 AWG (13AW

CLASS ROOM TABLE AND BENCH (Made of Powder Coated Steel and Laminated HDF Board) Size : TOP BENCH (1200mm X 500mm X 750mm) BENCH (1200mm X 400mm X 450mm)

TEACHER'S TABLE (Made of Powder Coated Steel and Laminated HDF Board) Size (1500mm X 600mm X 750mm)

STORAGE CLASS ROOM (Made of Laminated HDF Board) BACK STORAGE (1350mm X 650mm X 2100mm)

FURNITURE INFIRMARY ROOM (Made of Laminated HDF Board) Size : TABLE (1800mm X 750mm X 750mm) SIDE TABLE (900mm X 400mm X 725mm) BACK UNIT (3300mm X 450mm X 725mm)

TEACHING STAFF'S ROOM TABLE (Made of Laminated HDF Board) (1800mm X 750mm X 750mm)

OFFICE ROOM TABLE (Made of Laminated HDF Board) Size: TABLE (1200mm X 600mm X 750mm) SIDE TABLE (900mm X 400mm X 725mm)

WAITING ROOM OFFICE TABLE (Made of Laminated HDF Board) Size: TABLE (1600mm X 600mm X 750mm) SIDE TABLE (1200mm X 400mm X 725mm)

SIDE TABLE (Made of Powder Coated Steel and Laminated HDF Board)

PRINCIPAL CABIN FURNITURE (Made of Veeneered Plyboard) Size TABLE (2000mm X 750mm X 750mm) SIDE TABLE (900mm X 400mm X 725mm) BACK UNIT (2000mm X 450mm X 725mm)

PRINCIPAL ROOM CORNER TABLE (Made of Veeneered Plyboard)

PRINCIPAL ROOM CENTER TABLE (Made of Veeneered Plyboard)

CONFERENCE TABLE (Made of Veeneered Plyboard) (2400mm X 1200mm X 750mm)

COMPUTER TABLE (Made of Laminated HDF Board) Size (900mm X 600mm X 750mm)

BIO LAB TABLE (Made of Powder Coated Steel and Laminated HDF Board) Size (2000mm X 1200mm)

CHEMISTRY LAB TABLE (Made of Powder Coated Steel and Laminated HDF Board) Size (2000mm X 1200mm)

PHYSICS LAB TABLE (Made of Powder Coated Steel and Laminated HDF Board) Size (2000mm X 1200mm)

TEACHING STAFF'S ROOM & LIBRARY TABLE (Made of Powder Coated Steel and Laminated HDF Board) (1400mm X 1000mm X 750mm)

TEACHING STAFF'S ROOM FILE CABINET (Made of Laminated HDF Board) Size : (1200mm X 600mm X 2100mm)

LIBRARY WORKING TABLE (Made of Laminated HDF Board) Size (1800mm X 1800mm X 750mm)

LIBRARY STORAGE (Made of Laminated HDF Board) Size (900mm X 300mm X 2100mm)

HOSTEL BUNK BED (DOUBLE) (Made of Powder Coated Steel) including Mattress Size (1800mm X 900mm- MATTRESS SIZE)

DINING TABLE AND BENCH ( 10 SEATER) (Made of Powder Coated Steel and Laminated HDF Board) Size (2400mm X 1200mm X 750mm)

TEACHER CHAIR

REVOLVING CHAIR Infirmary Room, Teaching Staff's, Office, Waiting Room, Principal Visitor & Conference

LIBRARY CHAIR & EVERY COMPUTER SYSTEM

AUDIO/VISUAL ROOM TRANING CHAIR

PRINCIPAL CHAIR

HOSTEL STUDY CHAIR

PRINCIPAL & WAITING ROOM 2 SEATER SOFA

M/S Assam Electric Store