REPAIR / MAINT OF WATER SUPPLY DISTRIBUTION SYSTEM AT MIL STN FAZILKA.

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundations etc or manholes, cesspits, pipes and cables etc. not exc 10 Sqm on plan and getting out in soft / loose soil all as specified and directed by Engineer - in - Charge.

Removing excavated material n exc. 50m and depositing wheredirected at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers of soft / loose soil not exceeding 25cm thick all as specified and directed by Engineer - in - Charge.

Dismantling/Taking out CI/DI water mains (including all fittings) with spigot and socket ends and rubber gasket joints 150mm bore complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out CI/DI water mains (including all fittings) with spigot and socket ends and rubber gasket joints 200mm bore complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out CI/DI water mains (including all fittings) with spigot and socket ends and rubber gasket joints 250mm bore complete all as specified and directed by Engineer - in – Charge.

M & L for cast iron Fittings for spigot and socket /flanged pipes such as bends (any type, radius and angle) Tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch, ‘Y’ junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs upto 150mm bore pipes all as specified and as directed by Engineer-in-Charge.Make - Electrosteel, Leader,Kirloskar

M & L for cast iron Fittings for spigot and socket /flanged pipes such as bends (any type, radius and angle) Tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch, ‘Y’ junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs for 200mm to 300mm bore pipes all as specified and as directed by Engineer-in-Charge.Make - Electrosteel, Leader,Kirloskar

M & L for DI fittings for DI Spigot and socketed/ flanged pipes like bends (any type, radius and angle) straight, taper, bend, increasing, decreasing double socket etc.) tee pieces single branch “Y” junction double branch, cross collars, caps and plugs etc. complete all as specified. Note for DI Fittings :-The weight of the fittings for the purpose of payment shall be actual weight of the fittings or as specified in IS code whichever is less.

Burning out lead joint in position, including removing old for 150mm bore of pipes complete all as specified and as directed by Engineer-in-Charge.

Burning out lead joint in position, including removing old lead for 200mm bore of pipes complete all as specified and as directed by Engineer-in-Charge.

Burning out lead joint in position, including removing old lead for 250mm bore of pipes complete all as specified and as directed by Engineer-in-Charge.

M & L for run lead joint suitable for CI pipe of 150mm bore spigot and socketed pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

M & L for run lead joint suitable for CI pipe of 200mm bore spigot and socketed pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

M & L for run lead joint suitable for CI pipe of 250mm bore spigot and socketed pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

Dismantling joints of flanged pipes in position, including removing old rubber or fibre board gaskets, bolts, nuts. for 150 mm Bore of pipes.

Dismantling joints of flanged pipes in position, including removing old rubber or fibre board gaskets, bolts, nuts. for 200 mm Bore of pipes.

Dismantling joints of flanged pipes in position, including removing old rubber or fibre board gaskets, bolts, nuts. for 250 mm Bore of pipes.

M&L flanged joint with rubber or fibre board gasket including removing old rubber tighten Joint for 150 mm Bore of pipes.

M&L flanged joint with rubber or fibre board gasket including removing old rubber tighten Joint for 200 mm Bore of pipes.

M&L flanged joint with rubber or fibre board gasket including removing old rubber tighten Joint for 250 mm Bore of pipes.

M & L for tighten Joint with rubber or fibre board gasket including removing old rubber tighten Joint for 150 mm Bore of pipes.

M & L for tighten Joint with rubber or fibre board gasket including removing old rubber tighten Joint for 200 mm Bore of pipes.

M & L for tighten Joint with rubber or fibre board gasket including removing old rubber tighten Joint for 250 mm Bore of pipes.

M&L for cutting of existing road of width not exceeding 750 and n.exc 1.0 deep for laying of water mains and fitting back with excavated soil except road portion shall be made good with cement concrete 1:2:4 typeB1 using 20 mm graded stone aggregate complete all as specified as directed.

M & L for servicing of sluice valve cast iron body by greasing /oiling using necessary tools and plants as required as per manufacturer instructions and proving gland rope of superior quality and rubber gasket/ packing where necessary to stop any leakage of sluice valve of size 80 mm dia to 250 mm dia all as specified and directed.

M&L for leakage of water supply distribution lines 20 mmdia GI tubing by carryout necessary excavation in any type of soil, returning filling , removing, de watering as required, tightening of loose joints including, provision of GI fittings like union sockets,nipple, elbow etc all as required, threading jointing all as directed. Note :- (i) The qouted rates shall be inclusive of earth work excavation in any type of soil. (ii) The qouted rates shall be inclusve of necessary GI fittings and flanges, sockets, clamps, etc as required and nothing extra shall be paid to contractor on this account. (iii) GI pipe of length above 1.o mtr for rectification of complaints shall be measured and paid seperatly under the relavent items.

All as per tem no above but for GI tubing of size 40mm to 50 mm.

All as per tem no above but for GI tubing of size 80 mm.

S & F in repair brass check nuts as per existing size including opening bend portion of valve and refixing the same suitable for CI sluice valve of the 150/200 mm sizes

Supply and fixing in replacement sluice valve flanged type ISI marked (IS - 14846) heavy duty, Class PN 1.6 size 80mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge. Make - L&T, Venus, Leader.

Supply and fixing in replacement sluice valve flanged type ISI marked (IS - 14846) heavy duty, Class PN 1.6 size 100mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge. Make - L&T, Venus, Leader.

Supply and fixing in replacement sluice valve flanged type ISI marked (IS - 14846) heavy duty,Class PN 1.6 size 150mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge. Make - L&T, Venus, Leader.

Supply and fixing in replacement sluice valve flanged type ISI marked (IS - 14846) heavy duty, Class PN 1.6 size 200mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge. Make - L&T, Venus, Leader.

Supply and fixing in replacement sluice valve flanged type ISI marked (IS - 14846) heavy duty, Class PN 1.6 size 250mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge. Make - L&T, Venus, Leader.

S&F "D" Joint with nut and bolt suitable for 80mm bore DI/CI pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

S&F "D" Joint with nut and bolt suitable for 100mm bore DI/CI pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

S&F "D" Joint with nut and bolt suitable for 150mm bore DI/CI pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

S&F "D" Joint with nut and bolt suitable for 200mm boreDI/CI pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

S&F "D" Joint with nut and bolt suitable for 250mm bore DI/CI pipes and fittings complete all as specified and as directed by Engineer-in-Charge.

Dismantling/Taking out steel tubing 20mm bore and connections including fitting complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out steel tubing 25 or 32mm bore and connections including fitting complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out steel tubing 40 or 50mm bore and connections including fitting complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out steel tubing 80mm bore and connections including fitting complete all as specified and directed by Engineer - in – Charge.

Dismantling/Taking out steel tubing 100mm bore and connections including fitting complete all as specified and directed by Engineer - in – Charge.

S & F 20mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 25mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 40mm bore medium grade steel tubes galvanised with all fittings laid in trenches all as specified and directed by Engineer - in – Charge .

S & F 50mm bore medium grade steel tubes galvanized with all fittings laid in trenches all as specified and directed by Engineer - in - Charge .

S & F 80mm bore medium grade steel tubes galvanized with all fittings laid in trenches all as specified and directed by Engineer - in - Charge .

S & F 100mm bore medium grade steel tubes galvanized with all fittings laid in trenches all as specified and directed by Engineer - in - Charge .

Cutting existing 20mm bore tubing for alteration or addition complete all as specified and as directed by Engineer-in-Charge.

Cutting existing 25 or 32mm bore tubing for alteration or addition complete all as specified and as directed by Engineer-in-Charge.

Cutting existing 40 or 50mm bore tubing for alteration or addition complete all as specified and as directed by Engineer-in-Charge.

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 50mm bore complete all as specified and directed by Engineer – in – Charge.Make- Zoloto or Equivalent

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 40mm bore complete all as specified and directed by Engineer – in – Charge. Make- Zoloto or Equivalent

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 25mm bore complete all as specified and directed by Engineer – in – Charge. Make- Zoloto or Equivalent

S & F globe or gate valve with iron wheel head, screwed both ends for iron pipes 20mm bore complete all as specified and directed by Engineer – in – Charge. Make- Zoloto or Equivalent

Supply and fixing in replacement of reflux (Non -return) valve flanged type rating PN 1.6 size 80mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supply and fixing in replacement of reflux (Non -return) valve flanged type rating PN 1.6 size 100mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supply and fixing in replacement of reflux (Non -return) valve flanged type rating PN 1.6 size 150mm bore with necessary gasket, nuts, bolts and washers etc. and jointing including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supply and fixing in replacement of foot valve flanged type of size 80mm bore with necessary gasket, nuts, bolts and washers etc. including testing for leakage complete all as specified and directed by Engineer – in – Charge.

Supply and fixing in replacement of foot valve flanged type of size 100mm bore with necessary gasket, nuts, bolts and washers etc. including testing for leakage complete all as specified and directed by Engineer – in – Charge.

S & F in replacement of rubber type flexible couplings suitable for 7.5 to 15 HP motor pump set etc complete all as specified and directed by Engineer-in-charge.

all as per item No- 64 ( here- in-before) but Suitable for 20 to 25 HP

all as per item No-64 ( here- in-before) but Suitable for 40 HP

M&L cement concrete 1:3:6 type B-1 using 20mm graded stone aggregates on road cutting including necessary form work complete all as specified & directed.

M & L for boring hole across the Road/plinth/hard standing by trench less technology method suitable for 80/100mm bore pipe for 0.4 mpa working pressure for cable passing without damaging Road / Plinth /Floor complete all as specified and directed.

M&L for disconnecting/dismantling of Unsv 3 phase 415 Volt 50 Hz AC Electric motor 5 HP/ 7.5 HP, transportation to Civil workshop and strip opening of worn out/ defective brunt stator winding, services cleaning of stator slots, bearing bushes etc rewinding of stator coils with superior quality of copper enamel wire of existing size and specification including insulating material, varnishing and drying, reassembling, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge. Make of winding wire shall be ATLAS/Devi dayal / BPL (Note - defect libility for motor and pump shall be one year from date of Repair

M&L disconnecting/dismantling and strip opening of worn out/defective Centrifugal pump of capacity 5 HP/ 7.5 H mono block type, taking out unserviceable bush, sleeve & sleeve joint etc repair to Impeller & shaft with proper brass brazing welding & lath work, assembling, testing, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge.

M&L disconnecting/dismantling and strip opening of worn out/defective Centrifugal electric motor of capacity 15 HP/ 20 HP mono block type, taking out brunt stator winding, services cleaning of stator slots, bearing bushes etc rewinding of stator coils with superior quality of copper enamel wire of existing size and specification including insulating material, varnishing and drying, assembling, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

M&L disconnecting/dismantling and strip opening of worn out/defective Centrifugal pump of capacity 15 HP/ 20 HPmono block type, taking out unserviceable bush, sleeve & sleeve joint etc repair to Impeller & shaft with proper brass brazing welding & lath work, assembling, testing, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge.

M&L disconnecting/dismantling and strip opening of worn out/defective submersible electric motor15 HP/ 20 HP , taking out brunt stator winding, services, cleaning of stator slots, bearing bushes etc rewinding of stator coils with superior quality of copper enamel wire of existing size and specification including insulating material, varnishing and drying, assembling, testing and installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge. Make of winding wire shall be ATLAS/Devi dayal / BPL

M&L disconnecting/dismantling and strip opening of worn out/defective submersible pump 15 HP/ 20 HP, taking out unserviceable bush, sleeve & sleeve joint etc repair to Impeller & shaft with proper brass brazing welding & lath work, assembling, testing and installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge.

M&L disconnecting/dismantling and strip opening of worn out/defective Centrifugal electric motor of capacity 40 HP mono block type, taking out brunt stator winding, services cleaning of stator slots, bearing bushes etc rewinding of stator coils with superior quality of copper enamel wire of existing size and specification including insulating material, varnishing and drying, assembling, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge.

M&L disconnecting/dismantling and strip opening of worn out/defective Centrifugal pump of capacity 40 HP mono block type, taking out unserviceable bush, sleeve & sleeve joint etc repair to Impeller & shaft with proper brass brazing welding & lath work, assembling, testing, installing and connected at original location complete all as per specified and directed with entire satisfaction of Engineer-in-Charge.

Supply and fixing the following parts for centrifugal pumping set of capacity 5/7.5 HP

(a) CI Impellar

(b) Brash Bush

(c) Stainless steel shaft

(d) Ball bearing as per existing size & No. SKF/NBC/Worma

Supply and fixing the following spare parts for cintrifugal pumping set 15/20 HP

(a) CI Impellar

(b) Brash Bush

(c) Stainless steel shaft

(d) Ball bearing as per existing size & No.

All as per ser Item No above here-in- before but submersible pumping set capacity 15/20 HP

(a) Gun metal Impeller

(b) Stainless steel shaft

(c) Thrust rod

(d) Distance sleave

(e) Motor Bush

(f) Sealing kit

(g) Thrust plate

(h) Pump coupling stainless with key

(j) Studs & Nuts

Supply and fixing the following spare parts of contrifugal pumping set of 40HP capacity

(a) CI Impellar

(b) Brash Bush

(c) Ball Bearing 6306 SKF/NBC/Worma

(d) Ball bearing No. 7306 SKF/NBC/Worma

S&F in replacement fully automatic star delta starter 3 phase 415 volts, 50 HZ in steel metal encloser type MV with SSP feature suitable for 40HP motor & relay range as recommended by manufacturer etc incl taking out unserviceable startr from existing position complete incl taking down the existing all as specified and directed by Engr-in-Charge Make- Bentex

All as per ser No above but 20/25 HP motor & relay range as recommended by manufacturer

All as per ser No above but 10/15 HP motor & relay range as recommended by manufacturer

DOL starter 5/7 .5HP motor & relay range as recommended by manufacturer

S & F in repalcement of gear box with connecting GI pipe mixer for motor 3 HP motor with mounting bracket with suitable gear ratio as per existing specification

Supply and fixing the following parts for compressor and motor set of capacity 20 HP

(a) air blower

(b) Oil seal

(c) Stainless steel shaft

(d) Oil Suiltable specification

Supply & commissioning of Pumping sets, Monobloc AC three phase voltage rated 50Hz frequency , electric driven, supplied and installed complete 5HP three phase of head 20 mtrs with 150mm delivery line attachment all as specified and directed. Make Crompton/Kirloskar/CRI

M & L for painting of CI/DI pipes of raising mains and delivery lines of 6mtr in length as one job , LT panel, motors, Compressors as one job each item, with one coat of red oxide and two coats of existing colours of blue/black with approved make of paint , and writing of letters with specified colours, size as given by Engr-in-charge

Construction of brick masonry valve pit for Sluice valve all as specified and as per drawing including plastering, PCC in foundation, Excavation and earth work in any type of soil, MS sheet cover 3mm thick sheet with locking arrangement painted with two coat of anti corossive paint over one coats of zinc chrome primer of 900x900x900mm (type 'B').

Cleaning of clear water underground Sump of capacity 1,00,000 Gallons manually by traind and skilled manpower of working in under ground sumps/reservior with suitable T&P and safty equipments, Tools and safty measures. Draining out the contaminated muddy water from the bottem surface of sump and cleaning the side walls with the help of wire brush including removal green fungs leaves and other dust and dirt, scraping of dissolved impurities, removal of surface mud /silt ,cleaning with water and draining out complete unwanted meterial obtained from cleaning as well as apply spray of suitable approved disinfactant chemical on inner surface of the sump safe for human being and two coat spray painting with sky colour water proofing paint and two coats samocem on outer surface and writting the date of cleaning with synthetic enamal paint complete all as specified by Engineer-in-Charge.

Cleaning of Raw water jack well of capacity 20000 Gallons at Filteration plant manually by traind and skilled manpower of working in under ground sump/reservior with suitable T&P and safty equipments, Tools and safty measures. Draining out the contaminated muddy water from the bottem surface of reservior and cleaning the side walls with the help of wire brush including removal green fungs leaves and other dust and dirt ,scraping of dissolved impurities, removal of surface mud /silt ,cleaning with water and draining out complete unwanted meterial obtained from cleaning complete all as specified by Engineer-in-Charge.

Cleaning of inner surface of over head reservior 50,000 Gallons capacity manually by trained and skilled manpower for working in over head reservoir with suitable T&P and safety equipment, tools and safety measures. Darining out the contaminted muddy water from the bottom surface of the over head reservoir, scraping inner surface with the help or wire brush, incliding removal green fungs leaves and other dust and dirt, of dissolved impurties, removal of surface mud/ silt, cleaning with water and draining out complete unwanted material obtained form cleaning as well as apply spray of suitable approved disinfactant chemical safe for human being on inner surface and complete outer surface structure with and two coats spray painting with water proofing paint on inner wall of the tank,and writing the date of cleaning with synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Cleaning of inner surface of over head reservior 1,00,000 Gallons capacity manually by trained and skilled manpower for working in over head reservoir with suitable T&P and safety equipment, tools and safety measures. Darining out the contaminted muddy water from the bottom surface of the over head reservoir, scraping inner surface with the help or wire brush, incliding removal green fungs leaves and other dust and dirt, of dissolved impurties, removal of surface mud/ silt, cleaning with water and draining out complete unwanted material obtained form cleaning as well as apply spray of suitable approved disinfactant chemical safe for human being on inner surface and complete outer surface structure with two coats spray painting with water proofing paint on inner wall of the tank,and writing the date of cleaning with synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

Cleaning the clarifloculator Semi UG sump of diameter; 14.5 meter and depth not exceeding 7.5 meter by removing mud, sediments manually by trained and skilled manpower who working in UG sumps/ reservoir with safety messures, including scraping the inner surface by wire brush, brooms and removing the mud, green fungs, leaves, dust and dirts, draining out complete unwanted materials obtained from cleanning and two coats spray painting with sky colour water proofing paint on Inner surface of wall and two coats samocem on outer surface and writting the date of cleaning with synthetic enamel paint complete all as specified by Engineer-in-Charge.complete all as specified and directed.

Cleaning of bushes and grass, cutting the branches of trees if any over ramps and tappered surfaces of raw water /Over Head tanks and making good surfaces as existing all as specified and directed by Engr-in charge

Testing of water with collecting samples of desired places for every 30 days and producing the samples at govt testing labs by chemical & biological methods and collecting the reports of the same all as directed by Engr-in-charge.

Supply and fix in repairs four pole manual change over switch rating 100 amps,415 volts AC supply, ss enclosure ,installed and fixed on walls, panel all as specified and directed.

Supply and fix in repairs four pole manual change over switch rating 63 amps,415 volts AC supply, ss enclosure ,installed and fixed on walls, panel all as specified and directed.

M&L for removing Beehives of any nos, size and at upto height of 22 mtrs with all safety gear while removing hives with precautions at height and ladders required for climbing will carry, all as directed by engr-incharge.

N.R.Builders

RANDHIR AND COMPANY

m/s G.S. Enterprises

P.K ENTERPRISES