COMPREHENSIVE PETTY REPAIRS TO CERTAIN BLDG INCL PLASTERING, FLOORING , BRICK WORK, ROOFING AND OTHER CONNECTED B/R WORKS FOR ZONE A AGE B/R I UNDER GE (N) BIKANER.

Amount

Demolition of brick work built in cement mortar complete all as specified and directed by engineer in charge.

Demolition of cement conc. In ground floor and paving not exc. 15cm thickness (below or above GL) incl any type of floor finishes/topping complete all as specified and directed by engineer in charge.

Demolition of reinforced cement conc.as in chhajas, parapets etc. not exc. 15cm thickness complete all as specified and directed by engineer in charge.

Dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises as per directed by Engineer-in-Charge.

Demolition of lime conc. of any desc.and in any position not other wise specified complete all as specified and directed by engineer in charge.

Dismantling Asbestos cement Corrugated sheets in roof covering complete all as specified and directed by engineer in charge.

Dismantling plain or corrugated steel / transulecent sheeting any gauge, pattern, thickness incl nanital or similar pattern complete all as specified and directed by engineer in charge.

Dismantling one way Jaffri including taking as under of battens in trellis all as directded and as specified by Engineer in charge

Taking down cement plaster (any thickness and incl tiles if any) on brick or stone walls incl.raking out joints hacking for key scrubbing down with water etc.

Taking down chowkhats or frames not exc. 1.50sqm each but with shutter (w/o taking of shutter from the frame ) including Windows /ventilators complete

Taking down chowkhats or frames exc. 1.50sqm and not exc 4 Sqm each but with shutter (w/o taking of shutter from the frame )

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening including repairs and easing/adjustment to existing shutter complete.

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and romoving to store complete all as specified and directed by engineer in charge.

Taking down door shutter of any desc exc 2 sqm and romoving to store complete all as specified and directed by engineer in charge.

Taking down shutters of any description (Aluminum ) and refixing in same opening after carrying out necessary repairs , securing rails ,tightening scews ,hinges etc complete all as specified and directed by engineer in charge.

Taking down Aluminium door including chowkhat if required and repair the same including repair of rubber bedding , aluminium clip, adjustment of glass repair of floor spring or hydraulic door closer with oiling or greesing etc including adjusment of horizontal or middle style.complete all till the staisfaction of engineer-in-charge

Taking down aluminum windows including frame if required and repair the same including repair of rubber bidding,aluminum clip,adjusment of glasses,repair of floor spring or hydraulic door closer with oiling or greesing etc.ajusment of horizontal, vertical or middle style . complete all as till the satisfaction of Engr-in-charge.

Dismantling of existing false ceiling boards (fiber,pulp,insulation,mineral etc.) complete.

Hacking out old broken glass (any thickness size quality or desc.)from wooden frames or stone conc. or brick surroundsglazed with putty or fixed with beads complete all as specified and directed by engineer in charge.

Taking up or down steel water tubing 15mm dia and connection ,incl all fittings complete all as specified and directed by engineer in charge.

Taking up or down steel water tubing 20mm dia and connection ,incl all fittings complete all as specified and directed by engineer in charge.

Dismantling Rotational Moulded plyethyelene water strogr tank of capacity exc 250 lit but not exc 500 lit complete all as specified and as directed by Engineer-in-Charge.

Dismantling Rotational Moulded plyethyelene water strogr tank of capacity exc 500 lit but not exc 1000 lit complete all as specified and as directed by Engineer-in-Charge.

Dismantling structural steel work including doors,gates but excluding framed trusses complete all as specified and directed by engineer in charge.

M&L for RCC pillarrs in Pcc 1:2:4 type B-1 set in cement mortar 1:4 moulded 100 x 100mm x 75cm long precast complete fixed and specifed and as directed by Enginer-In-Charge.

M&L for Providing cement concrete RCC jalli 35mm thick type B0 1:2:4 using 12.5mm graded aggregate (measured solid) including all mouldings but exc frame complete all as specified and directed by engineer in charge.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed by engineer in charge.

M&L for Brick work with sub class B bricks straight or curved on plan to any radius in half brick walls built in CM 1:4 parapet complete all as specified and directed by engineer in charge.

M&L brick work with fly ash bricks straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed by engineer in charge.

M&L for Rendering 15mm thick on fair faces of brick or conc. Surfaces in cement mortar 1:6,even and smooth w/o using extra cement complete all as specified and directed by engineer in charge.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4. (Note: Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location)

M&L for Rendering 5 mm thick on fair faces of conc. Surfaces in cement mortar 1:3,even and smooth w/o using extra cement as on ceiling complete all as specified and directed by engineer in charge.

M&L 15 mm thick rough cast plaster in Cement mortar 1:4 consists of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with course sand and cement in the ratio of 1:1:1 complete all as specified and as directed by Engineer-in-Charge. Note: The rate quoted shall be deemed to include for necessary use and waste of form work if required and nothing extra shall be paid on this account).

Supply only liquid water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

M&L Providing PCC 1:4:8 as in sub base/mass concrete type D-2 using 40mm graded stone agg complete all as specified and as directed .

M&L for 40 mm thick PCC type B-1 ( 1:2:4) 20mm graded aggregate as in pcc flooring as in surface finished with out using extra cement complete all as specified and directed by engineer in charge.

Supply only 3mm thick glass 38mm wide glass dividing stripps laid in design as directed by Eng-in-charge

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

All as per item 38 above but on vertical surface over 10 mm thick rendering in CM (1:4) complete all as specified and directed by engineer in charge.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

All as per item 40 above but on vertical surface over 10 mm thick rendering in CM (1:4) complete all as specified and directed by engineer in charge.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

All as per item 42 above but on vertical surface over 10 mm thick rendering in CM (1:4) complete all as specified and directed by engineer in charge.

M&L for 10 mm thick Vitrified colored tiles of size n.exc. 0.36 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces.(Note:The contractor shall have no claim on difference what so ever on shade /colour of tile). Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

Ditto as per Serial item 44 above but with 10 mm thick in CM 1:4 as on vertical surface complete all as specified and directed by engineer in charge.

M&L for 10 mm thick Vitrified colored tiles of size exc. 0.36 Sqm but not exceeding .0.42 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces.(Note:The contractor shall have no claim on difference what so ever on shade /colour of tile).complete all as specified and directed by engineer in charge. Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

Ditto as per Serial item 46 above but with 10 mm thick in CM 1:4 as on vertical surface complete all as specified and directed by engineer in charge.

M&L for 10 mm thick Vitrified colored tiles of size exc. 0.42 Sqm but not exceeding .1.00 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces.(Note:The contractor shall have no claim on difference what so ever on shade /colour of tile).(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

Ditto as per Serial item 48 above but with 10 mm thick in CM 1:4 as on vertical surface complete all as specified and directed by engineer in charge.

M&L for Glazed ceremic tiles white 450X300mmX7mm thick coloured,set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

M&L for Machine cut kota stone slab 18 - 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl.rubbing and polishing laid over 15 mm thick cement screed base in CM 1:6. The joints shall be 20mm wide filled with cast in situ tarrazo with white marble chips of size up to 6mm.(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

Ditto all as per item No 51 above but in skirtings laid over 10mm thick backing layer in CM 1:4 complete all as specified and directed by engineer in charge.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L Sand stone slab 25-35mm thick set jointed and pointed self faced punched dressed laid as in chhajas, sunshade and man holes covers set in cement mortar 1:4 incl.making chases in wall complete all as specified and directed by engineer in charge.

M&L Granite 20 mm thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite over 15 mm thick screed bed of CM 1:6 complete all as specified and directed by engineer in charge.

M&L Rendering 10 mm thick on fair faces of brick /stone patti or conc. Surfaces in cement mortar 1:4 even and smooth w/o using extra cement as on roof slab mixed with liquid water proofing compound of Dr FIXIT/Sikka complete all as specified and directed by engineer in charge.

Preparing surface and cleaning of concrete slab by wire brushing and aplying evenly a tack coat of industrial bitumen 85/25 @ 1.70 Kg per sqm including cleaning surfaces complete all as specified and as directed by Engr-in-chanrge

150 micron polythylene sheet supplied and fixed complete all as specified and as directed by Engr-in charge

M&L for Lime conc. terracing as specified in roof treatment complete all as specified and directed by engineer in charge.

Extra over lime conc. Terracing for top surface trowelled smooth incl cement mixture to make homogeneous paste.

M&L for 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in bands/coping ,benching and the like incl form work complete all as specified and directed by engineer in charge.

M&L for 6mm thick asbestos cement corrugated sheets in roofs, walls fixed with L-type or cranked hook bolts complete all as specified and directed by engineer in charge.

M&L for Asbestos cement two piece adjustable ridge 6mm thick fixed with Lor J hooks / coach screws complete all as specified and directed by engineer in charge.

M&L for rolled section /tubular section as in main and cross beams , purlins , rafters ,posts where connected to common rafter and running rails etc conforming to Fe- 410-w complete all as specified and directed by engineer in charge.

M&L for steel Work in tubular trusses including special sahped washers etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St. 240 complete all as specified and directed by engineer in charge.

S&F 2mm thick glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and directed by engineer in charge.

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified. (Note - Color Sand/or as approved By Garrision Engineer)

M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.(Note - Color Sand/or as approved By Garrision Engineer)

S&F in repairs 12 mm mineral fiber insulation board tiles of size 600mmx 600mm fixed in snap grid complete Make:- Armstrong,Bison and equivalent

S&F in repairs anodised aluminium snap grid frame work of size 605 x 605mm for false ceiling including necessary notching. The snap grid shall consist of anodised aluminium main/cross tee of size 36.5 x 25 x 1.4mm weighing 0.24Kg/RM and 23.5 x 26.4 x 1.4mm weighing 0.191 Kg/RM respectively. The main and cross T section shall be jointed at junction crossing with anodised aluminium angle bracket of size 15 x 15 x 1.5mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washers. The snap grid shall be supported at ends all along with wall with anodised aluminium angle of size 40 x 25 x 2mm wieghing 0.36Kg/RM fixed to wall with suitable arrangements and providing 12mm thick mineral fiber board in grid and applying two coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and as directed by Engr-in-Charge

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest or as approved ) designer ceiling conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with holding down bolts suspenders and adjusters

S & F in repairs stainless steel tubular curtain/drapery rod 25 mm dia ( in length as directed) with & including pair of projecting type fancy stainless steel brackets fixed at both ends with PVC rawl plug & steel screws on wall/beam complete all as specified and as directed .

S&F 1.25 mm thick Pressed steel frames of size 125mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.complete all as specified and directed by engineer in charge.

S&F 1.25 mm thick Pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.complete all as specified and directed by engineer in charge.

S&F Flush Shutters 30 mm thick , solid core construction, with block board core and plywood face panel , commercial type on both side complete. Including edges of door covered with teak bid and makng provision for fixing mortice lock and hinges complete.

S&F 2nd class hard wood 35mm thick plain framed panelled factory made shutter two panels with lock rail and panels of 9mm BWP commercial ply or 12mm veneered partical board with veneered veneering on both side .size of rails as pes IS-1003 kiln seasoned and chemically pressure treated comp all as specified.

S&F 2nd class hard wood glazed and skeleton shutters 35mm open rebated and prepared to receive glass, gauze etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I section 8, clause 8.20 (a) supplied and fixed to chowkats complete all as specified and directed by engineer in charge.

S&F 25 mm thick Flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed by Engineer-in-Charge.

Prelaminated partical board 19/20mm medium density ,prelaminated with one side with decorative choice laqmination and other side balancing with white lamination , stitched with20 mm thick wooden bead all around fixed with screws as in shelves to kitchen almirah and cub board fixed in repair complete all as specified and directed by engineer in charge.

S&F 12 mm thick plywood, 5 ply grade BWE, type BB fixed with screws to timber frame work with 0.9mm decorative laminate type 1 of surface finish, colur and pattern as approved fixed with approved adhesive as per maker,s instructions complete all as specified and directed by engineer in charge.

S&F in Repairs 10 mm thick plaster of paris ceiling ( gypsum anhydrous) to flat surface over 2 nd class soft wood fillets, or mental frame work and reinforced with GI wire mesh and reinforced with GI wire mess ( fillets, metal frame work and G.I wire mesh paid separately). complete all as specified and as directed .

Ditto as per srl item 82 above but on curved surface complete all as specified and directed by engineer in charge.

Ditto as per srl item 82 above but with and including any sunk or raised moulding complete all as specified and directed by engineer in charge.

S& F in Repairs Moulding of gypsum anhydrous boards of any design fixed to edges of walls complete all as specified and as directed by Engineer-In-Charge.

S&F in repairs designer blocks of gypsum anhydrous boards fixed to ceiling at apening not exceeding 0.20 Sqm complete all as specified and as directed by Engineer-In-Charge.

S&F factory made mild steel Window box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F Steel ventilators or windows fixed type with glazing bar.(Making good and fixing of windows with P.C.C 1:3:6 Type C-2 included in the item) complete all as specified and directed by engineer in charge.

S&F framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe290 Gde -E-165 complete all as specified and directed by engineer in charge.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification.

S&F anodised aluminum door window frames /shutter ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as specified. .

S&F powder coated aluminum door window frames/shutter ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as specified. .

S & F in repair aluminium glazing clip with rubber gasket of suitable size and thickness as required at site for fixing glass in aluminium door/windows complete all as specified and directed by Engineer-in-Charge.

S&F in repair sheet glass 5.5 mm thick ordinary quality & glazing with rubber gasket in squares exc 0.5sqm in each pane as in aluminium door/window complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodised barrel tower bolt of extruded section of 150mm complete all as specified and directed by engineer in charge.

S&F mild steel butt hinges medium weight cold rolled mild steel of 100mm complete all as specified and directed by engineer in charge.

S & F in Repair Piano Hinges mild steel ,bright finish width of flaps open in 40mm all as specified and directed by engineer in charge

S&F Aluminium handles cast type anodised of 150mm complete all as specified and directed by engineer in charge.

S&F mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with and incl. A minimum of 6bolts and nuts four on bolt plate and two on staple plate of 250mm long complete all as specified and directed by engineer in charge.

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 150mm complete all as specified and directed by engineer in charge.

S&F mild steel pressed handles oval type stove enamelled black of 150mm complete all as specified and directed by engineer in charge.

S&F in repair 300mm mild rat tail rod pattern springs including roller and, roller plate and welded to chowkhats and taking down old unservicabale spring, complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge.

S&F as in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by engineer in charge.

S&F Sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane complete all as specified and directed by engineer in charge.

S&F in repair MS steel window handles (left/right) fixed to steel windows including reveted / welding if required complete all as specified by Engineer- in - Charge.

M&L for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed by Engineer-in-Charge.

S&F in repair Hasp and staple 100mm safety type,Aluminium anodised,withmild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified by Engineer- in - Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete.

S&F anodised aluminum American handle cast type 200mm for doors complete all as specified and directed by engineer in charge.

S&F anodised aluminum handle cast type 100mm collapsible type complete all as specified and directed by engineer in charge.

S&F anodised 75mm size butt hinges , type C21 extruded aluminum alloy ISI marked complete all as specified and directed by engineer in charge.

S&F 100 mm long Butt hinges extruded aluminium alloy , with galvanised mild steel hinge pin, anodised, type B-21, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium anodised, barrel tower bolt of extruded section, size 150 mm, complete all as specified and as directed by Engineer-in-Charge.

S&F anodised aluminum handle cast type 100mm complete all as specified and directed by engineer in charge.

S & F in repair for door closer hydraulically regulated , designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 KG and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass 4 lever mortice lock, vertical type size 100mm suitble for existing aluminium door complete all as specified and directed by Engineer-in-Charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover, govering pivot made of brass other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge.

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets,complete all as specified and directed by engineer in charge.

Attending complaints of rolling shutters of any type any height and anylength making functional by providing greasing oiling , welding etc.including taking down rolling shutters or hood if required complete all as specified and as directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by engineer in charge.

S&F Ball bearing for rolling shutters complete all as specified and directed by engineer in charge.

S&F 15 mm bore tubes medium grade galvanised with all fittings and fixed to walls or laid in floors complete all as specified and directed by engineer in charge.

S&F 20mm bore tubes medium grade galvanised with all fittings and fixed to walls or laid in floors complete all as specified and directed by engineer in charge.

S&F Rotational moulded polythene ISI marked water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 500 ltrs complete all as specified and directed by engineer in charge.

S&F Rotational moulded polythene ISI Marked water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs complete all as specified and directed by engineer in charge.

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm complete all as specified and directed by engineer in charge.

S&F in repairs stop valves cast copper alloy chromium plated fancy type/concealed type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by engineer in charge.

S&F in Repairs Bib taps cast copper alloy with crutch or butter fly handle screwed for iron pipe for 15mm bore dia of pipe fixed in repair complete all as specified and directed by engineer in charge.

S&F in repairs bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by engineer in charge.

S&F in Repairs Bib taps standard of PTMT any colour high pressure screwed for iron p[ipe and fixed of 15mm fixed in repair complete all as specified and directed by engineer in charge.

S&F in repairs pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F Stop valve cast copper alloy (concealed type) with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair.

S&F in Repairs Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous china wash down water closet Orissa pattern white padestal pattern of size 550x440mm including integral foot rest excluding flushing cistern and flush pipe) incl. P or S trap comp all as specified and fixed in repairs. Make Parryware/Cera/Hindware

S&F in repairs PVC flushing cisterns 10 ltrs capacity including flushing pipe and connections complete . Make : CERA ( CAT No: B1010108 , or equivalent in Parryware ,Jaquar, Hindware as approved by Eng-in-Charge .

Plastic water closet seat cover white/coloured ,closed pattern with flat bottom pattern and cover and mild steel chromium plated or aluminium hinging device fixed in repair complete all as specified and directed by engineer in charge.

S&F in repairs wall hung water closet ( size 510x365x380 mm) of superior quality including all fitting fixtures concealed cistern complete all as specified and as directed Make : Jaquar , cera , parryware . Note: Brick work and tilings shall be paid under separate item

S&F in Repairs water closet pedestal patteren white or coloured ( as approved by Engr-In-Charge) make: Cera CAT No.- S1013113 ( CRISTY Single Piece suite P or S trap incl Seat cover) or equivalent in Hindware ,jaquar,parryware) as approved by Engr-In-Charge.

S&F in rerpairs Table top WHB Cat Part No: -S2020106 Cera Cloister or equivalent in approved makes including pop Up waste Coupling fixed complete all as specified and as directed by Engineer In Charge.

S&F in rerpairs Counter shunk WHB Cat Part No: - CERA S2030102 450x350 mm OVAL or equivalent in approved makes including pop Up waste Coupling fixed complete all as specified and as directed by Engineer In Charge.

S&F wash hand basin vitreous china size 550x400mm white flat back as approved by GE ,waste,chain plug,pvc connection, pvc waste pipe comp all as specified fixed in repair

S&F viterous China urinal half stall type white including CP spreader, waster pipe etc complete all as specified and directed by engineer in charge..

PVC connection of PTMT nuts 15x600mm long fixed in repair.

S&F PVC connection of PTMT nuts 15x450mm long fixed in repair complete all as specified and directed by engineer in charge.

S&F kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers and waster, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and conneting union to pipe overall size 915mm x 460mm bowl size 410 x 330 x 160mm

S&F Chromium plated soap dish complete all as specified and directed by Engineer-in-charge.

S&F Vitereous china wash down water closet pan (Pedestal pattern) white including trap bolts etc complete including connections to drain and anti siphonage pipe.

S&F in repairs health faucet with 1 mtr long tube and hook and knob al as specified and directed by Engineer-In-Charge. Cat Part No BEA 40 of Prayag/jainko/sakti

S&F CP toilet paper holder fancy type complete all as specified and directed by Engineer-in-charge.MAKE: JAQUAR OR EQUIVALENT as approved by Eng-in-Charge .

S&F Towel ring of cast copper alloy chromium plated fixed and repair ( CAT PART NO: BA-02 , MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

S&F in repairs Towel Rackstainless steel with and including hangers Make: Jaquar CAT No. AQN 7781A or equivalent inHindware, parryware) as approved by Engineer In Charge.

S&F two way angle cock of cast copper alloy chromium plated fixed and repair ( CAT PART NO: 7211 , MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

Waste pipe 32mm for WHB with coupling fixed in repairs.complete all as specified and directed by engineer in charge.

S&F in repairs Central hole basin mixer for hot and cold water brass chromium plated screwed down with long sunk and fly nuts screwed for 15 mm dia (( CAT PART NO: 7250, MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

S&F in repairs 15 mm bore wall mixer with telephone shower arrangement make :- Jaquar Cat Part No. CON-267KN or equivalent in Hindware, Jaquar,Parryware) as approved by Engineer-In-Charge.

S&F in repairs stainless steel peg set of 06 pegs foldable or fixed complete all as specified and directed by Engineer-In-Charge.

S&F chromium plated cockroach trap (150mm x 150mm) with or without waste hole flat border. Make Parayag, CAT No: FT-30M or Equivalent in Hindware Jaquar, Parryware) as approved By Eng-In-Charge.

S&F in Repairs Overhead shower 200x200m square shaped single flow with and including shower arm 400x25x25 mm square shaped for wall mounted showers . Make: Jaquar CAT Part No.:- OHS-35497,SHA-455L400 or Equivalent in Hindware, Parryware as approved by Engineer-In-Charge.

Waste pipe 40 mm for SINK with coupling fixed in repairs complete all as specified and directed by engineer in charge.

S& F in repair internal fitting of PVC low level cistern as per existing pattern to make the PVC low level cistern fully functional complete all as specified and as directed by Engineer- in - Charge.

Supply and fixing 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed.

Supply and fixing 75 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, laid in trenches or floors, fixed in repairs, complete all as specified and as directed.

Supply and fixing 50 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.

Supply and fixing 100 mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.

Supply and fixing 75mm bore cast iron, sand cast, soil, waste & vent pipe (ISI marked), in any length with or without ears fixed with cement joints, fixed to walls, fixed in repairs, complete all as specified and as directed.

S&F in repairs stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 50mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

S&F in repairs stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 75mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

S&F in repairs stack clamp made out of MS flat 50mm x 5mm and 16 mm dia round iron stays, including bolts & nuts, securing ends of stays to walls or roof for 100mm bore pipe including two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified & as directed.

S&F in repairs 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

S&F in repairs 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified & as directed.

S&F in repairs 100mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.

S&F in repairs 75mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified & as directed.

Supply and fixing cast iron cowl for 50 mm bore CI pipe complete all as specified.

M&L for extra over cast iron pipe & fitting 100mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.

M&L for extra over cast iron pipe & fitting 75mm bore providing lead joints in lieu of cement joints complete all as specified and as directed.

S&F in repairs cast iron floor trap of 100 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.

S&F in repairs cast iron floor trap/nahani trap of 75 mm bore, with grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4), complete all as specified & as directed.

S&F in repair PVC (SWR) floor trap plain 75mm dia with PVC grating including jointing with solvent cement complete all as specified and directed by Engineer- in - Charge.

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 110mm as in rain water pipe complete all as specified and directed by engineer in charge.

S&F PVC(SWR)single socketed in any length with rubber ring joint laid in floors of 110mm as in rain water pipe complete all as specified and directed by engineer in charge.

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 75mm complete all as specified and directed by engineer in charge.

PVC(SWR)single socketed in any length with rubber ring joint laid in floors of 75mm complete all as specified and directed by engineer in charge.

PVC SWR branch piece single equal or unequal 110mm with owl access complete all as specified and directed by engineer in charge.

PVC SWR branch piece single equal or unequal75mm with owl access complete all as specified and directed by engineer in charge.

S&F PVC SWR S trap laid and jointed to 110 mm bore PVC pipes complete all as specified and directed by engineer in charge.

PVC(SWR) bends any radius 110mm. With owl accesscomplete all as specified and directed by engineer in charge.

PVC(SWR) bends any radius 75mm. With owl access complete all as specified and directed by engineer in charge.

S&F in repair pvc cowls , 75 mm dia complete all as specified and directed by engineer in charge.

Cutting chases,pinning in making good to facing where requried and pointing in cement mortar 1:3 to ends or edge of landings,steps,cills,sunshade,shelves, lintel etc. tubes or concealed conduit etc. and making good, cutting not exc 10 cm girth complete all as specified and directed by engineer in charge.

Preparing new decorated surfaces plastered/unplastered by brooming down etc and applying two coat of distemper oil emulsion on walls inner site including cornices pilasters etc complete all as specified.

Preparing old finished surfaces of walls including cornices, pilasters etc and applying one coat of distemper oil emulsion, white or tinted as directed by the Engr in Charge.

Preparing surfaces of plaster or unplaster new and applying two coat of ccement based paint complete all as specified and directed by engineer in charge.

Preparing old decorated surfaces treated with cement base paint of walls cornices pilaster etc and applying one coat of cement base paint (Ist quality) in plain pattern on walls complete all as specified.

Preparing surfaces of plaster or unplaster new and applying two coat of white wash on walls complete all as specified and directed by engineer in charge.

Ditto all as per item no 198 abovee but as on ceiling complete all as specified and directed by engineer in charge.

Preparing surface of wood of any desc over 10cm width ot girth and applying two coats of synthetic enamel paint complete all as specified and directed by engineer in charge.

Preparing surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by engineer in charge.

Preparing surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by engineer in charge.

Dismantling Old scantling over 40 sqcm in section framed work in any position.complete all as specified and directed by engineer in charge.

Dismantling Old scantling fillets,rail,posts,rafters,purlins, etc under 40 sqcm framed work in section in any position complete all as specified and directed by engineer in charge.

Cutting to existing kota stone/dholpur flooring including minor repairs and polishing complete

N.K. CONSTRUCTION COMPANY

ALPHA ENGINEERING COMPANY

M/S ASHRAFI CONSTRUCTION CO