Construction Of Sports Complex for Shree Balaram Residential School at Amone Canacona Goa

Clearing grass and removal of rubbish upto a distance of 50 m outside the periphery of the area

Felling trees of girth(measured at a height of 1. m. Above ground level) inluding cutting of trunks and branches removing the roots stacking the serviceable material and disposal of unserviceable material for all leads : Beyond 30 cm and upto 60 cm grith

Beyond 60 cm and upto 120 cm grith

Beyond120 cm and upto 240 cm grith

Beyond 240 cm girth

Surface dressing of ground including removing vegetation in equalities not exceeding 15 cm deep and disposal of rubbish lead upto 50 m and lift upto 1.5 m. Ordinary Rock

Earthwork in surface excavation not exceeding 30 cm depth (but exceeding 1.5 m width as well as 10 sq.m on plan) including disposal of excavated earth beyond work site for all leads lift disposed earth to be leveled and neatly dressed in: Ordinary Rock

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas(Upto any depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : All kinds of soil

All type of ordinary rock including all type of laterite rock, blasting prohibited

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. All kinds of soil.

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. Sand

Moorum

Clearing jungle including up rooting of rank vegetation grass bush wood trees and sapling of girth upto 30 cm. measured at a height of 1 m above ground level & removal of rubbish upto a distance of 50 mt. outside the periphery of the area cleared. (if however, only grass is met with the area will be measured and paid for under item 4001).

Providing anti – termite treatment to buildings conforming to I.S.S. 6113 part II 1971 (revised) including adopting precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals, plants, equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (The payment will be made on plinth of the building. Pre-construction

Post construction

Disposal of moorum/building rubbish/ malba/ surplus excavated earth similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading Complete including Royalty

Filling of the plinth/foundation with outsource earthworks.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in sizes in superstructure from floor I level upto floor V level.

Half brick masonry in cement mortar 1:4 (1 cement : 4 coarse, sand) with bricks of class designation 75 kg/ sq. cm upto floor five level .

Providing and laying Autoclave Aerated cementblocks masonry (Light Weight Foam ConcreteBlocks) with 100 mm thick AAC blocks in superstructure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). Therate includes providing and placing in position 2Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: All works upto plinth level

In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level.

Providing and laying upto floor five level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc. For Encasing the Tree Columns, T-Columns etc proposed for Elevational treatment etc complete (Size 600 mm Dia and 7.5 Mts height) including Walls including attached buttresses pilasters, string courses, independent piers, columns and pillasters coping and the like. upto floor five level.

Centering & shuttering including Strutting, Propping & removal of forms for : Foundations, footings, bases for columns and mass concrete.

vertical surfaces such as retaining walls , return walls, walls (any thk) including attached pilasters, buttresses, plinth and string courses, fillets, etc.

Columns, Pillars ,piers,abutments, posts and strut, square, rectangular, polygon in plan. etc.

Providing and laying upto floor five level precast cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including hoisting and setting in position in cement mortar 1:3 (1cement : 3 Coarse sand) including smooth finishing the exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc. Kerbs, steps and the like at or near ground level

String courses, copings, bed plates, anchor blocks, plain window sills and the like.

Small lintels not exceeding 1.5 m clear span, including coping and the like requiring form work to suspended portions.

Providing & laying damp proof course 40 mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone agg 12.5 mm nominal size).

Making plinth protection 50mm thick of Cement Concrete 1:3:6 (1cement: 3 Coarse Sand: 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry laterite aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded granitic or basaltic stone aggregate 40 m nominal size) excluding cost of centering, shuttering and finishing : In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level.

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering, shuttering, finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size). All works upto plinth level

In walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. upto floor five level.

In beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases upto floor five level.

Providing and laying upto floor five level reinforced cement concrete (1:2:4) in kerbs, steps and the like excluding the cost of centering, shuttering and finishing and reinforcement (1 cement: 2 coarse sand: 4 graded grantic or basaltic aggreate 20mm nominal size.

Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1½ :3 (1cement: 1:1½ coarse sand: 3 graded stone agg 20mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, Footings, Bases for columns

Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Staircases (except spiral staircases) excluding landing

Suspended floors, roofs landings, shelves & their supports

Vertical or horizontal fins individually forming box louvers or projected bands

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates. Cornices & Mouldings

Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de- shuttering and de-centering at all levels, over a height of 3.5m, for every additional height of 1m or part thereof. (Plan area to be measured)Suspended floors, roofs, landings, beams and balconies (plan area to be measured).

Providing TMT steel reinforcement bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) )(Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin-charge. All works upto floor V level. M-35 grade of concrete

Extra for shuttering in circular work (20% of respective centering and shuttering items)

Providing 10 cm drip course at junction of roofs and wall in cement mortar 1:4 (1 cement : 4 fine sand) with bricks of class designation 75 kg / cm2.

Constructing cast-in situ RCC diaphragm wall by providing and laying machine batched, machine mixed, self compacting, ready mix reinforced cement concrete, tramie controlled, of M 30 grade using minimum 400 kg. cement per cum of concrete including providing and mixing required admixtures in recommended proportions as per IS:9103, as approved by the Engineer-in-charge, for achieving 150- 200mm slump, for diaphragm wall having thickness as per approved structural design not exceeding 600 mm, in panels of required depth and lengths as per approved drawing, including constructing necessary guide walls as required and as specified including boring in all kinds of soils and rocks, including working in or under water and / or liquid mud,in foul conditions and pumping or bailing out of water and removing slush, including disposal of earth/ rock / slush etc. for all leads and all lifts, including preparing, providing and re-circulating bentonite slurry in the trench as and when required for all depths, including agitating bentonite slurry during trenching etc., providing and fixing stop ends or form tubes, upto the required depth of diaphragm wall including extracting the same after casting, including chipping off the bentonite adulterated concrete or unsound concrete up to the cut off level for obtaining the sound concrete, dressing undulations on the exposed face of diaphragm wall after excavation by chipping / chiseling etc. including filling the depression/ cavities with sound concrete etc. complete and as directed by the Engineer- in-charge, including providing recess for bearing plates and fixing insert boxes for inclined rock anchors etc. complete as per the specifications and approved design and as directed by the Engineer-in-charge, but excluding the cost of reinforcement and inserts.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in positon. Second class Indian teak wood

Providing and fixing 50 mm thick panelled glazed or panelled and glazed shutters for doors, windows and clerestory window including anodized aluminium butt hinges with necessary screws: First class Indian teak wood

Providing and fixing flush doors shutters commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering and vertical grains or cross bands and face veneers on the both faces of shutters. 35mm thick including anodized aluminium butt hinges with necessary screws:

Extra for providing vision panel not exceeding 0.1 sq.m. in all types of flush doors (cost of glass excluded). Rectangular or square Unit: SQ.M. door area

Providing and fixing bright finished brass door latch with necessary screws etc complete. 300x 16 x 5 mm

Providing & fixing bright finished brass 100 mm. mortice latch & lock & a pair of levers, handles with necessary screws etc. complete (Indian make of approved quality).

Providing & fixing bright finished brass 100 mm. rim latch & lock & a pair of knob, with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing chromium plated brass flush bolts with necessary screws etc. complete. 250 mm

Providing and fixing chromium plated brass handle with necessary screws etc. complete. 125 mm

Provided and fixing 150 mm chromium plated brass floor door stopper with rubber cushion screws etc. to suit shutters thickness complete.

Wood Finish Wood Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wooden styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) and printed matt having wooden textures used along with UV Resistant resin to give the clear texture on the door. The core of shutter will be filled with MR 2nd grade Block Board. The Shutter to be water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories: i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nos iv) Handle 5” - 2 Nos Note: For 35 & 40mm thickness shutters, only frames of 5 x 2 ½ Cross section frames to be used. Shutter Thickness 35mm

FRP (Fiber Reinforced Polymer) Frames with Wood Finish Manufacture, Supply and Installation (with anchor fastener) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) Frame of cross section as per options below with right angle joint and FRP (Fiber Reinforced Polymer) laminate made from 450 grams per sq.mts (gsm) chop strand glass fiber (matt) and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps). The core of frame would be filled with seasoned wood as infill material. The slot of frame for door resting will be of suitable width so as to take specified thickness door. The frame will be water proof as well as mild acid/ alkali resistant manufactured in an ISO 9001- 2015 certified company. Specified Cross Section : 5” x 2 ½ “

Providing and fixing M.S. fan clamp type 1or II of 16 mm dia M.S. bar bent to shape with hooke ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete.

Providing & fixing M.S. round holding down with nuts & Washer plates complete

Providing & fixing bolts with nuts & washer complete.

Providing & fixing M.S. Rivets of sizes in position.

Welding by gas plant (using Ador or ES4B or Deh Secheron make electrodes only)

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality asper grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer. (The item includes cost of material such as cleats,sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick luminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing . The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assemble working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick luminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

Steel work(SAIL, TATA. VIZAG only) riveted, welded sections or bolted sections (ISMB, ISMC, L/T-Sections etc) in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint etc complete. In tees, I-Sections, Channel sections of any size, profile etc and upto any desired height and levels including Y-Columns, T-Columns (Tree column arrangement), base plate with riveted, bolted &/or welded arrangements etc complete.

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. In R.S. Joists

In tees, angles, flats and channels

Providing and fixing of three track standard sectional aluminium windows with three tracks and three shutters sliding windows with tubular frame sections powder coated with pure polyster powder of thickness 15-80 microns with approved standard acessories such as ball bearing rollers concealed lock, 6mm plain clear glass with EPDM beading etc complete

Providing & Laying PCC for Auditorium Floor coprising of 50mm thick cement concrete flooring with under layer of 40 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layers 12 mm thick mix 1:2 (1 cement: 2 graded stone aggregate 6 mm nominal size by volume including finishing etc complete.

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand). 20 mm thick.

Kotah stone slab flooring over 25 mm thick in risers of steps, skirtings, dado & pillars laid on 12mm (average) thick cement mortor 1:3 (1 cement : 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete.

Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. 600 x 600 mm light Shades

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete.. 900 x 900 mm - light Shades

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm . Jet Black

Cherry Red

Providing and Laying Brick finished cladding tiles / stone dado cladding in varying sizes etc complete

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. Dark Shades

Light Shades

25 mm wooden plank tongued and grooved, in flooring including fixing with iron screws complete with Second class Indian teak wood.

Providing and and laying wooden finish /vertified Ceramic floor tiles in planks (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. Wall Ceramic Glazed Tiles : 300 x 600

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing 20mm thick marble slab to urinal partitions with cement complete

Providing corrugated G.I. sheet roofing, fixed with galvanized iron j or 1 hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete excluding the cost of purlins rafter and trusses. 0.63 mm thick sheet - 24 G

Proving ridges or hips of width 60 cm over all in plain G.I. sheet fixed with galvanized iron J or L hooks bolts and nuts 8 mm. 0.80 mm thick sheet.

Providing valleys 90 cm overall in plain 1.60 mm thick G.I. sheet fixed with galvanized iron j or l hooks bolts 8mm dia G.I. limpet and bitumen washers complete.

Providing angular fillets 7.5 x 7.5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone) ggregate 20mm nominal size)

Making khurras 45 x 45cm with average minimum thickness of 5cm of cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate of 20mm nominal gauge) finished with 12mm cement plaster 1: 3 (1 cement: 3 coarse sand) & a coat of neat cement rounding the edges and making and finishing the outlet complete.

Supplying and Providing in position under deck 50mm thk non combustible Glass wool insulation 24 kg/m3 density with white prelaminated polypropelene facing (WMP-50) under the metallic roof complete for sound and heat insulation including cost of GI welded mesh of 75x75x1.60 thk streched over purlin complete. The GI Welded mesh should be primed and painted with min. 2 coats of superior quality ready mixed paint for steel work.

Providing and fixing in position Space Frame structure in Stainless Steel hollow tubular sections including pivoted / hinged joints, etc complete as per detailed Technical specifications

12mm cement plaster 1:6 (1 cement : 6 fine sand)

15mm cement plaster 1: 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall.

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

6mm cement plaster to ceiling 1: 3 (1 cement : 3 fine sand)

Extra for plastering exterior walls of height more than 10m from ground level for every additional height of 3m or part thereof.

Distempering two or more coats with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade.

Providing and applying Synthetic elastomeric coating cum paint of reputed make such as Polysafe or equivalent conforming to relevant IS specification ready to use for bridge structures in saline atmosphere as to avoid salt concentration from marine environment, ultra-violet effects of the sun rays, fungus development and to protect the reinforcement from marine atmoshpheric effects in 3 coats including sand blasting, cleaning the concrete surfaces brushing and applying the polymerbased chemical coating with PRIMER, 1ST COAT and SECOND COAT at an interval of 24 hrs in approved shade and colour including scaffolding etc. (as directed by the Engineer-in-charge) complete with 5 yrs guarantee).

Supplying and stacking of good earth at site including royalty and cariage upto 1 Km (Earth measured in stacks will be reduced by 20% for payment)

Spreading of sludge, dump manure or/and good earth in required thickness (cost of sludge, dump manure or/and good earth to be paid separately).

Trenching in ordinary soil upto a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking sludge at site including royalty and cariage upto 1 Km (sludge measured in stacks will be reduced by 8% for payment)

Supplying and stacking at site dump manure from approved source, including carriage upto 1 km (manure measured in stacks will be reduced by 8% for payment). Screened through sieve of I.S. designation 20mm

Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods ands mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flodding with water , filling with earth if necessary, watering and finally fine dressing, levelling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed , within a lead of 50m lift upto 1.5m complete (cost of sludge, manure or extra earth to be paid for separately).

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately). Holes 60cm dia. and 60cm deep

Half brick circular tree guard in 50 class designation bricks, internal diameter 1.25 metre and height 1.2 metre above ground and 0.20m below ground bottom two courses laid dry and top three courses in lime mortar 1:2 (1 lime putty : 2 surkhi) or cement mortar 1:6 (1 cement : 6 fine sand) and intermedate courses being in dry honey comb masonary as per design complete. With common burnt clay F.P.S. (non modular) bricks of class designation 5.0

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Providing following Plants in the premises: Providing & planting plants as per approval on site with all neceesary supports, pots etc. complete as required a) Ficus Benjamina Bushy king sun loving

b) Ficus benjamina

Galphimia Glauca (Yellow)

Ixora singaporensis (Dark red)

Champa , Chameli, Ratrani,Juhi, Kanher, Kunda, Zhendu, Shevanti, Jai

Musanda (Pink+White +Dark red)

Roses hybrid tea / Roses florabanda

Thuja compacta

Agaves

Arica palm

Pentas lanceolata "Cemea" Yellow

Pentas lanceolata "Cemea" White

HEDGES Golden duranta(Yello)

Acalypha Wilkesiana Tricolour (red)

Mehandi hedge

Providing & fixing (4’) 100 mm sand cast iron grating for gully floor or nahni trap.

Providing & fixing 600 x 120 mm glass shelf with C. P. brass brackets and guard rail complete fixed to wooden cleats with C. P. brass screws.

Providing and fixing toilet paper holder. C.P. brass

Cutting chase in brick masonry walls for fixing 100 mm diameter sand cast iron pipes & making good the same with brick work in cement 1:3 (1cement :3 fine sand)

Cutting chase in brick masonry walls for fixing 50 mm diameter sand cast iron pipes & making good the same with brick work in cement 1:3 (1cement :3 fine sand).

Providing and fixing brass bib cock (heavy) of approved quality : 15 mm nominal bore.

Providing and fixing C.P. brass shower rose with 15 or 20 mm. Inlet: 150 mm diameter

Providing and fixing brass stop cock (heavy) ofapproved quality. 15 mm nominal bore.

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design : 150 x 100 mm size –P or S type

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1: 1 1/2:3 mix (1 cement: 1 1/2 coarse sand ;3 graded stone aggregate 20mmbnominal size foundation concrete 1:1 1/2:3 mix (1 cemet ;1 1/2 coarse sand :8 graded stone agrregate 20mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat ofneat cement and making channels in cementconcrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)neatly finished complete as per standard design. Inside size 90 x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x610mm internal dimensions total weight of cover ad frame to be not less than 38 kg.(weight of cover23 kg).

Inside size 1.2m x 90 cm and 90cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter total weight of cover and frame to be not less than 116 kg. (weight of cover 58 kg).

Extra for depth for manholes : size 1.2 x 90 cm

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Internal work exposed on wall (Medium duty SDR 13.5pipe). 15 mm nominal outer dia. Pipes.

20 mm nominal outer dia. Pipes.

25 mm nominal outer dia .Pipes.

32 mm nominal outer dia. Pipes.

40 mm nominal outer dia. Pipes.

50 mm nominal outer dia. Pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solventcement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 15 mm nominal outer dia .Pipes.

20 mm nominal outer dia .Pipes.

25 mm nominal outer dia .Pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement, trenching, refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe) 32 mm nominal outer dia. Pipes.

40 mm nominal outer dia. Pipes.

50 mm nominal outer dia. Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work. 62.50 mm nominal inner dia. Pipes.

75 mm nominal inner dia. Pipes.

100mm nominal inner dia. Pipes.

150 mm nominal inner dia. Pipes.

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming toIS 8931;1993. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete.(Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91 m internal dia (at bottom) beyond 0.91 m to 1.67 m With Sewer bricks conforming IS : 4885

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing premium quality wall hung type closet including push button concealed flushing system device manually operated, solid seat cover with lid, cascade health faucet and all other fittings and fixtures complete including cuttings and making good the walls and floor wherever required. The water closet shall be of with a basic price not be less than Rs. 10000/-.

Providing and fixing steel Kitchen sink (510x1040 mm bowl depth 225 mm.) bowl size on the kitchen plateform including providing and fixing base coupling, waste pipe etc complete including Providing and fixing swan nack cock of parryware or equivalent approved make for kitchen sink, cleaning and curing etc complete. Make of sink : Nirali

Providing and fixing of any shape over-counter wash basin including Tall Body Basin Mixer, One Aquisense sensor faucet for wash basin with base flange , brass waste coupling, and all other fittings and fixtures complete including cuttings and making good the walls and floor wherever required The wash basin and basin mixer shall be of Parryware/H&R Johnson/Hindware with a total basic price of not less than Rs. 10000/-.

Providing and fixing 100 mm dia weight not less than 100 gms. stainless steel jali (grating) with or without hole for waste pipe of for floor or Nahani trap

Providing and fixing C.P. BRASS Bottle Trap for Wash basin and sink. Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 230mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 260gms.

Providing and fixing Stainless steel towel ring circular shape 200 mm size with a minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and make.

Providing and fixing CP Brass soap Dish Holder of Jaquar Continental make or equivalent of approved quality with fittings etc. complete as directed by Engineer in charge.

Providing and fixing Automatic Soap Dispenser with Glass Bottle 110 mm wide,128 mm high and 132 mm distance from wall of standard shape withbracket of the same materials with snap fittings of approved quality and colour, as directed by Engineer in charge

Providing, checking, storing & fixing Automatic Perfume Sprayer of CERA -6912 or equivalent, fixed to wall / door with concealed CP screws etc. complete as per direction of engineer-in-charge

Providing, checking, storing & fixing solid state, no touch operating, fully hygienic hand drier of ASKON:ASH-VJ or equivalent with double blower continuous repeat usage, time delay, including providing necessary brackets, cable from drier to plug. Plug top key and lock etc. having 3years warranty complete as required.

Providing, checking, storing & installation of basement / Ground level sump pumps for storm water / soil and waste, with suction and delivery from 80 mm to 100 mm dia pipe size, with all connections making suitable foundation and connecting to power supply provided by owner. Piping paid under respective item. (10 cum / hour - at 20 m head , 2 KW ). Set of 2 pumps - 1 Working + 1 standby)

Making connection of CPVC distribution branch with CPVC main of following sizes by providing and fixing tee, including cutting and threading the pipe etc complete. 25 to 40 mm nominal bore

Providing and fixing ball valve of CPVC of approved quality (screwed end). 25 mm dia nominal outer dia pipes

32mm dia nominal outer dia pipes

40mm dia nominal outer dia pipes

50mm dia nominal outer dia pipes

62.5mm dia nominal inner dia pipes

75mm dia nominal inner dia pipes

Providing and fixing CPVC non-return valve of approved quality (screwed end). Horizontal 40 mm nominal bore

Veritcal 40 mm nominal bore

Horizontal 50 mm nominal bore

Veritcal 50 mm nominal bore

Horizontal 62.5mm dia nominal inner dia pipes

Horizontal 75 mm dia nominal inner dia pipes

Providing and fixing soil, waste and vent pipes including M.S. Z bracket. 65MM DIA P.V.C.

75MM DIA P.V.C.

110MM DIA P.V.C.

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 65MM DIA P.V.C.

75MM DIA P.V.C.

110MM DIA P.V.C.

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 65MM DIA P.V.C.

75MM DIA P.V.C.

110MM DIA P.V.C.

Providing, laying and jointing DWC pipes including testing of joints etc. complete : 150 mm diameter

200 mm diameter

250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round DWC pipes including bed concrete as per standard design: 150 mm diameter DWC pipe

200 mm diameter DWC pipe

250 mm diameter DWC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of DWC pipes including bed concrete as per standard design : 150 mm diameter DWC pipe

200 mm diameter DWC pipe

250 mm diameter DWC pipe

Providing and fixing in position heavy duty C.I. manhole cover and frame of required shape and approved quality (120Kg). Rectangular shape 600x450 mm internal dimensions

Providing and laying integral cement basedtreatment (Box type) for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer and consisting of : ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer using rough Shahbad/Kotah stone.

Providing and laying integral cement based treatment (Box type) for water proofing on the vertical surface by fixing specified stone slab 20 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer using rough Shahbad/Kotah stone.

Providing water proofing treatment over the new R.C.C. roofs terrace toilet by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 ( 1 cement : 3 find sand), finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb, cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m.

Design, supply & installation of suspended Spider Glazing system (Frameless glass structural glazing) designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding , other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion ofGlass panel inside the SS channel shall be measured.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality asper grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer. (The item includes cost of material such as cleats,sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels including: a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml. e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in- charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this sub- head. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places. Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL (National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories. (1) Performance Laboratory Test for Air Leakage Test (- 50pa to - 300pa) & (+50pa to +300pa) as per ASTM E- 283-04 testing method for a range of testing limit 1 to 200 mVhr. (2) Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3) Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml. (4) Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm. (5) Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site. (6) Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, desiccants, including primary seal and secondary seal (structural silicone sealant) etc., all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Air gap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by the technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc., all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer- in- Charge.

Providing and placing in position controlled cement concrete of M-40 grade using minimum cement content as 400Kg/cum and max water cement ratio of 0.40 for Prestressed Concrete Girders as per detailed drawings and designs having form finish surfaces including formwork on casting bed and temporary supports as necessary and required, compacting by vibrators, levelling, curing and finishing etc. complete as specified and directed including launching the girders in position using plant and equipment and providing erecting and removing the temporary staging as necessary and required etc. complete as specified and directed excluding reinforcement and placing in position. (Using RMC/Batch Mix Plant, Tansit Mixer and Concrete Pump). PSC M-40 Grade. Using RMC/Batch Mix Plant, Tansit Mixer and Concrete Pump. For solid slab / voided slab super-structure. Floor Height upto 5m. Note: - The quantity shall be measured every floor level and for the height of floor not exceeding 5.0 Mts and not the height of the building in totality for the purpose of quantity measurements and payment. For T-beam & slab including girders etc upto any lift, leads etc

Floor Height upto 5m. Note: - The quantity shall be measured every floor level and for the height of floor not exceeding 5.0 Mts and not the height of the building in totality for the purpose of quantity measurements and payment.

High tensile steel wires/strands including all accessories for stressing, stressing operations and grouting complete as per drawing and Technical Specifications.

Providing and fixing Helical pipes in voided concrete slabs

Designing, Supply & fixing of Storm Resistant Rain Defence Performance Double Bank Louvers made up of Aluminium Extrusion of 6063 T6 alloy tested by AMCA/BSRIA to maintain the pressure drop below 8 mm and the airflow co-efficient should be not more than 0.28 to provide good airflow and excellent Rain defense of Class A. The panel size should be not less than 1200mm * 1200mm and should sustain the wind pressure of 2.0 Kpa. The Elevation should be continuous line with Powder coating finish to stand a warranty of 20 years.

Designing, Supply & fixing of Airfoil Projection (Elevational cantilever projection) comprising of 50mm wide Aluminium hollow circular or square pipes and for an Projection of 1000 mm, module with interconnecting 4 blades of requisite pitch as per design and blade supporting span of maximum 1800 mm to sustain a wind loading of 2.0 Kpa. The blade thickness to be minimum of 2 mm to sustain the wind load with Aluminium outrigger peripheral frame of 6 mm thickness & width of 75 mm. The coating to be in high end Powder coat as per the architectural intent and with warranty of minimum 5 years. The rate shall be inclusive of proper anchorage to the external walls / ACP or structural glazing framework including anchor fasteners, fixtures, hardware, fittings etc complete. The measurements for this items shall be considered as running metre length X total projection upto the outermost point.

CNC CUT PANELS Designing, Supplying, Assembling / fabricating, Installation, finishing, testing and fixing in position of 3mm thick 6063 T6 Aluminium Laser / CNC Cut Elevational Panels (Jali design) of approved make, color, shape, size & design and to have monotonous span without joint as per manufacturers specifications & standards. The product composition to be Aluminium with extended exterior coatings . The assembly to be fixed using 19mm SS 316 (10mm or 20mm), Coloured 22mm Wafer Head Screws, Aluminium rivets etc complete to the satisfaction of the Engineer in charge and as per directions

Providing, fabricating, assembling and erection of Tensile Fabric for Roofing, Walling, Side enclosures, Elevational treatment / Facade works etc and wherever directed by the Engineer in charge of the project comprising of PVDF coated tensile fabric of Type-III fabric having minimum weight of 1000 g/sqm with flame retardant as per particular specification. The rate to comprise of any design, color, texture including artistic design as per directions, craft etc in any size, span, color combinations, theme, design, texture etc complete including PVDF lacquer on both sides. The Colour of the fabric should be white background with design and colors in combination depicting art & muralic type display, Conditional Warranty of 20 years on the fabric, over steel frames with all fittings and fixtures such as Galvanised MS Membrane/ End Plate, Shackles, Rigging Screws, Turnbuckles, swedge, fork, keder rods & galvanized MS strands/ cables with stainless steel end terminals complete as per Drawing/ Detail & as per specifications and as per the instructions of Engineer-in-charge. The Rate includes cost of fabric , shop drawings, forming, cutting, fabrication, hot weld stich of fabric, Transport to the site, assembling and installation with GI cables, hardware, Aluminium flat, EPDM gasket and required accessories wherever required complete including lifts up to all heights, tools and plants, and necessary scaffolding etc. required for all operations in all respect.) The rate shall also include the Supporting Aluminium sectional framework, transomes, mullion sections etc as provided for the items of Aluminium composite Panels, Structural Glazing or other facade work items or structural steel framework as may be required etc complete. The necessary shop drawings shal be prepared by the agency showing the design calculations, loading conditions, resistant to wind loads etc. All tests as required for elevational treatment and facade works shall be included in the rate quoted for the said item. (Note: Actual facade elevational area in Sq. Mts or Surface plan area for walling / elevational works or roofing respectively shall only be measured for payment. The rate quoted for the above item shall be inclusive of Providing, Fabricating, Assembling, painting, hoisting, erecting and placing in position Aluminium sections of size as per design calculations and shop drawings, mullion and transome sections etc complete or MS Built-up section/Tubular Structure ( MS built-up section :-Rolled section & plates confirming to IS 2062 minimum required grade E250,Tubular Structure:- made from Steel hollow sections, ISI marked conforming to IS 1161/4923, minimum required Grade YST 310, in the profile shape as per drawings. Rate to also include special plate connector, pinion joints, Plates, hollow sections etc. using water jet 3-D cutting system for obtaining smooth 3-dimensional curvature, SAW/MMAW/MIG welding process with special plate connectors, pinion joints, plates, hollow sections to all heights, tools and plants and necessary scaffoldings etc. required for all operations involved. The structural members shall be painted with 350 DFT anticorrosive protection coating using Primer cum MIO of approved make with two coat of Epoxy Primer cum MIO 125 microns (each coat) thick and final coat of polyurethane paint 100 microns thick (to be applied in 2 coats). Up to all heights including preparation of the surface by copper slag blasting before application of primer/paint as per SA2.5 standards. The item shall be executed as per approved drawings, Particular Specifications and direction of the Engineer-in-Charge

Providing and fixing Anti-static, Anti-slip even when wet surface, durable, flexible Rubber flooring suitable for GYM/Sports complex of size 500 x 500 mm minimum with thickness of 25 mm should be laid on the top of the PCC in desired pattern or as per the instruction directed by an engineer incharge. Make: Vinex or equivalent.

Providing and fixing Badminton flooring of surface Litchi and Tree Bark of thickness 4.5mm with 100% Pure PVC Abrasion, Resistant Layer Glass Fiber Layer, Hermetic Stable Layer, High Density Foam Mute Shock Absorption over the wooden flooring with marking of proper badminton court dimension with suitable paint. Make: Vinex/yonex or equivalent.

Providing and and laying vitrified floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete - 600 x 600 mm light Shades

Pantry Counter - Providing and erecting pantry counter 2'-0" wide pantry / kitchen counter with cudappa undercarriage frame, 11/2" thk with one side polished and top to be finished with 18 mm thk high gloss mirror polished black pearl granite in the desired shape & size including half round nosing & grooves. The undercarriage frame of the counter shall be in sandwitch cadappa verticals with granite facia of size 6" to be fixed to verticals and top of the counter & nosing with edge polish including a cut-out for sink etc complete as per directions & instructions of the Architect. The rate shall be inclusive of providing & fixing S.S service trolleys below with standard sliding channel sections as per manufacturers specifications for the complete length and height of the counter including including shutters in marine plywood beneath the entire length of the counter including the necessary t.w frame and to be finished with decorative 1.0 mm thk laminate and including As per the directions / to the satisfaction of the Architect.

Providing and Fixing Synthetic Door matting system of LG, Nomad or equivalent make as per manufacturers specifications to match the finished floor level in the adjoining areas

Providing & placing in position Stainless steel perforated Dustbins of standard manufacturers specifications and make etc complete as instructed by EIC. (10" Dia x 14"-H)

Same as above but Providing & placing in position Plastic Dustbins of standard manufacturers specifications and make etc complete as instructed by EIC. (10" Dia x 14"-H)

Providing and erecting in position trap door in 12mm thk BWR IS 303 grade 19mm Thk Plywood to house, A.C. ductable units to be made out of 2" x 11/2" t.w. frame with openable shutter in ply with necessary hinges, tower bolts, locks, painting etc. finished as per the instructions and design.

Providing & Fixing in position Trap doors to house AC indoor ductable units, service trap door made out of 50mm x 38mm aluminum frame and 19mm thk marine ply consisting of openable panels. The shutter to be finished in 1.0 mm thk laminate of approved shade and color, both inside and outside and all wooden members shall be finished in paint.

Supply and Installation of Fire rated Door of minimum 45mm thickness of Godrej or equivalent approved as per standard manufacturers specifications & complying with the relevant sections of B.I.S codes and National Building codes of India. - FD1 - Size = 1000 x 1800mm (Single Leaf) Fire rated steel door (Minimum of Two hours fire rating) with fire rated square vision panel of size 380 mm X 380 mm including SS ball bearing butt hinges, mortice sash lock, SS lever handle with internal thumb turning arrangement, heavy duty type and external key operation including door frame, heavy duty floor spring and panic bar for opening the door of Dorma or equivalent make etc complete.

FD2 - Size = 1000 x 2100mm (Single Leaf) Providing & fixing in position Wooden fire rated door (Minimum of Two hours fire rating) with Vision Panel (Aprox - Door size - 1000 x 2100mm) including SS ball bearing butt hinges, mortice sash lock, SS lever handle with internal thumb turning arrangement, heavy duty type and external key operation including door frame, heavy duty floor spring and panic bar for opening the door of Royal Touch or equivalent approved make as per manufacturers standard specifications etc complete.

Providing and fixing Full ht. double skin Partitions as per specifications including skirting, complete as per the design, drawings and instructions in all respects. The specifications for the said item shall comprise of the following and with varying finishes as mentioned hereinunder: - FRAMEWORK -2"x2" Aluminium section of 16 Gauge verticals at minimum 1' 6"-2'-0" Centre spacing approx and 2" X 1" size Aluminium sections horizontal at 1' 6"-2'-0" Centre spacing approx extra frame below slab soffit for conduit to run above. All verticals secured to ceiling. Measurement of the said item shall be upto the False Ceiling level. SKIN:- Both side with BWR IS 303 grade 19mm Thk Plywood screwed to frame work on both sides with joints as shown or directed. SKIRTING : In the same alignment, 3" high in BWR IS 303 grade 19mm Thk Plywood with a groove finished with laminate / veneer as the case maybe, or as directed by the Architect. The rate shall include providing & fixing t.w. beading all throughout the exposed edges & periphery, sealing all the joints, grooves in finishes, melamine polish to the mouldings & t.w members, complete as per the directions of Architect. All Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically. The finishes for the skinning to be screwed to the framework on both the sides as duly mentioned above shall comprise of the following types: - Both side skins to be finished with 1.0 mm thk Laminate as shown in drawing or as directed by Architect.

Both sides to be directly finished with skin in 12 mm thk approved Gypsum Board to be screewed directly to the Aluminium framing, levelling etc complete. Rate to also include Providing & Fixing Acryllic Emulsion Paint finish to the skin in coats of desired number

Both sides to be directly finished with skin in 12 mm thk approved Gypsum Board to be screewed directly to the Aluminium framing, levelling etc complete. Rate to also include Providing & Fixing approved wallpaper over the skin surface (Basic rate of Rs. 200/ Sq. Fts plus taxes {GST})

Providing and fixing FRAMEWORK in 2"x2" Aluminium section of 16 Gauge verticals at minimum 1' 6"-2'-0" Centre spacing approx and 2" X 1" size Aluminium sections horizontal at 1' 6"-2'-0" Centre spacing approx extra frame below slab soffit for conduit to run above including 12mm thk designer MDF board on both sides including finishing both sides with PU machine polish including all the necessary surface preparations, final finish etc complete of approved shade, colour & texture as shown in drawing or as directed by Architect, including necessary grooves etc complete.

Providing & Fixing Low height Partition as per specifications including skirting, complete as per the design requirements mentioned above, drawings and instructions in all respects with an height of 4'-0" to 4'-6" to be erected in 2" X 2" Aluminium section of 16 Gauge verticals not exceeding 1' 6" to 2' 0" centres and 2" X 1" size Aluminium sections horizontal at floor level / skirting ht, intermediate level & 3'-0" level with 12mm. thk Exterior grade Partical Board skin on both sides of the frame to be screewed to the frame with joints as directed upto a height of 3'-0" to 3'-6" including 5.5mm thk glass with bevelled edges of 1'0" to 1'6" height, including approved frosted film of approved make & design on the glass including soft board panel with felt cloth. The partical board skin to be finished with 1.0mm thk laminatewith t.w. beading all throughout the exposed edges & periphery including fixing the glass with studs, sealing all the joints, grooves in laminate, melamine polish to the mouldings & t.w members, complete as per the directions of Architect. All Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically. All works shall be carried out as per Architectural drawings and the directions of Engineer-in-charge. Both sides of the partition finished with 1.0mm thk laminate, of approved grade as per the drawing including designed grooves etc complete.

Providing & Fixing full height Semi-Glazed partition as per specifications including skirting, as per the design, drawings and instructions in all respects. The specifications for the said item shall comprise of the following and with varying finishes as mentioned hereinunder: - FRAMEWORK - 2"x2" Aluminium section of 16 Gauge verticals, not exceed 1' 6"-2'-0" centres and 2" X 1" size Aluminium sections horizontal at floor level / skirting ht, 3'-0" level and door height at 7'-0" level. All verticals secured to ceiling. Measurement of the said item shall be upto the False Ceiling level. SKIN:- Both sides of the main frame shall be finished with BWR IS 303 grade 19mm Thk Plywood screewed to the frame with joints as directed upto 3'0" level and from 7'0" level to the top upto false ceiling level and including 6 mm thk. clear glass Straight / segmented with bevelled edges including frosted film of approved make & design and drawing to be fixed with t.w moulding all around of approved size & design including grooves, mouldings etc complete as directed by Architect & as shown in the drawing. SKIRTING : In the same alignment, 3" high in BWR IS 303 grade 19mm Thk Plywood with a groove finished with laminate / veneer as the case maybe, or as directed by the Architect. The rate shall include providing & fixing t.w. beading all throughout the exposed edges & periphery including fixing the glass with studs, sealing all the joints, providing grooves in the finish, melamine polish to the mouldings & t.w members, complete as per the directions of Architect. All Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically. The finishes for the skinning to be screwed to the framework on both the sides as duly mentioned above shall comprise of the following types: - One side skin to be finished with 1.0mm thk approved laminate & other side skin with 1.0mm thk approved laminate as shown in drawing or as directed by Architect.

Full Height Fully Glazed partition - Providing and erecting in position full height fully glazed Door in 12mm thk. toughened glass fixed on Patch fittings including top patch fitting, bottom patch fitting, patch lock, Floor spring of approved make for the door and S.S handle 600mm long, 30mm dia for the door including designer decorative frosted film of approved make, shade & design on the glass. AlI damages to the floor work to be reinstated without any extra cost including the cost of other fittings & fixtures & hardware such as spider panels, glass to glass contactors etc complete, necessary holes, joints to be sealed with silicone sealant on all sides complete in all respects etc as per directions of Architect.

Providing and erecting in position full height fully glazed partition in black sectional profiles / Silver Annodized natural Aluminium Modular Glass Partition using standard track section of size 45 mm X 25 mm profile as per manufacturer's standards and specifications and as directed by the Architect including single glazed 10mm thk clear toughened glass to be fixed in the centre of the track section, single door frame size to allow upto 35mm thk door of any type including Glass to glass I, T, L joint and connectors, standard assessories as per manufacturers recommendations & standards, gaskets etc complete. The rate shall include providing and fixing in position Door in same elevation, section, profiles, aluminimum framing system, gaskets and all related fittings, fixtures, hardware etc complete (Partition shall be measured including the door with matching elevation, if any and provided as per the plan), within the same matching framework as provided in the partition system including necessary fitting, fixtures such as locking system, flushed hinges, glass door hinge, heavy duty door closers, floor springs as per requirements, cove profile & skirting etc as per manufacturers recommendations & standards and S.S handle 600mm long, 30mm dia for the door. Rate to also include providing and fixing in position frosted film of approved make, shade & design on the glass. AlI damages to the floor work to be reinstated without any extra cost including the cost of other profiles, hardware, assessories, fittings & fixtures & hardware etc complete, necessary holes, joints between door, glazed partition panels (Glasses) to be sealed with silicone sealant on all sides complete in all respects etc as per directions of Engineer in charge

Providing and fixing Wall & Column Panelling for the existing surfaces to be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6" to 2' c/c to be covered with BWR IS 303 grade 19mm Thk Plywood and finished with approved 1.0mm thk laminate including skirting & band at top in the same alignment with a groove and including teakwood moulding of approved size as shown in detailed drawing or as directed by Architect. {Item shall be operated on all surfaces including fixing above the storage units mounted on exterior walls within cubicles and as an partial enclosure to the exposed Glazing portion} Area Considered in Accountatns Cabin, Superintendent Engineer Cabin, Exce.Engineer Cabin, Libraries

Providing & Fixing designer approved Fabric Panelling of Armstrong, Anutone or equivalent make including approved leatherite, satin or approved fabric of standard width over and 25mm thk glasswool or soft board backing, total thickness as per manufacturers specifications. The NRC to be minimum of 0.9. All around the panelling, decorative teak wood mouldings shall be provided and shall be finished with melamine polish complete as per the instructions of Architect.

Providing and fixing Accoustical Board Panelling for the existing surfaces to be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1' 6" to 2' 0" c/c to be covered with 19 mm thk. plywood boxing with internally 19 mm thick ply support finish and over which with 12 mm thick Acoustic Panels (Feltina 100% Wool Felt) board with a minimum NRC of 0.95 etc complete.

Providing and fixing Wall & Column Panelling for the existing surfaces to be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1'6" to 2' c/c bothways to be directly finished with skin in 12 mm thk approved Gypsum Board to be screewed directly to the Aluminium framing including complete. The finishes for the said item shall comprise of the following: - Providing & Fixing Acryllic Emulsion Paint finish to the skin in coats of desired number (Rate quoted includes Gypsum panelling including paint)

Providing & Fixing Textured Paint finish finish to the skin (Rate quoted includes Gypsum panelling including paint)

Providing & fixing approved wallpaper over the Gypsum surface in paneling, false ceiling or any surface as directed. ((Rate quoted includes Gypsum panelling including wallpaper). (Basic rate of Rs. 160/ Sq. Fts).

Providing & Fixing Mirror Panelling using 6 mm thick mirror of approved make over 19mm 710 BWP grade Marine Plywood backing. The mirror to be fixed with T.W beading of size 12.5mm X 19mm, finished with melamine polish complete as per the instructions of EIC. The rate shall be inclusive of providing & fixing S.S studs of appropriate size & diameter as directed including bevelling for the mirror

Providing and fixing Wall & Column Panelling for the existing surfaces to be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1' 6" to 2' 0" c/c to be covered with BWR IS 303 grade 19mm Thk Plywood backing and finished with 4mm designer, decorative MDF board including coats of duco paint of approved shade, colour & texture including teakwood moulding of 4mm size all around the periphery as directed by Architect

Providing and fixing Wall & Column Panelling for the existing surfaces to be made out of 16 gauge Aluminium framework backing of size 2" X 1" at 1' 6" to 2' 0" c/c to be finished with CNC cut panels of 4mm thk 3D MDF decorative panel of any size, design & pattern such as open jali, engraving etc and including coats of duco paint of approved shade in any colour & texture including necessary cove lighting arrangements with frosted 8mm acryllic sheet backing to be fixed using teakwood moulding all around the periphery etc complete as directed by Architect.

Glazed DOOR : Providing & Errecting in position Fully glazed Single &/or Double leaf Fully Glazed Main Entrance doors of any size & height as per plan & as directed by the Architect including its side fixed glass in 12 mm thk Toughened Glass on Patch fittings for each of the door leaf including top patch fitting, bottom patch fitting, patch lock, Floor Spring etc including all necessar hardware, fittings, fixtures etc of recommended manufacturer such as Dorma or equivalent approved including S.S handle 600mm long, 30mm dia including frosted film of approved make, shade & design on the glass. AlI damages to the floor work to be reinstated without any extra cost including the cost of other fittings & fixtures & necessary hardware, necessary holes, providing & fixing automatic acoustical drop seal on doors, joints to be sealed with silicone sealant complete in all respects etc as per drawings and directions of Architect.

Metal frame False Ceiling of 12 mm thk. Gypsum Board including vertical drop panels. Providing and Fixing 12 mm Thk. Gypsum board on metallic grid, conforming to IS: 2095: :1982. The metallic grid shall consists of the following : Gl Perimeter channels of size 27mm and 0.5mm thk. having one flange of 20mm and another flange of 30mm. Gl intermediate channel of size 45mm 0.5mm thk. With two flange of 15mm each at 4'-0" centre to centre. Gl Hanger of size 1"x1", 0.5mm thk. A 4'-0" centre to centre distance. Gl Cleat and Steel Expansion Fasteners. Ceiling section of 0.5mm thickness having curled wedge of 51.5 mm and two flanges of 26mm each with lips of 10.5mm at 450mm center to center. Connecting clips & 12.5 mm dry wall screws at 230 mm center to center. 'The metallic grid shall be installed as follows : The perimeter channel along the perimeter of the ceiling with screw fixed to brickwall / partition with the help of rawlplugs and screws. The intermediate channels shall be suspended from the ceiling with steel Gl hanger fixed to the slab soffit with Gl cleat and steel expanation fasteners.The intermediate channels shall be at 4'-0" centre to centre distance. The ceiling section placed in a direction perpendicular to the intermediate channel at 1'-6" C/C distance shall be fixed to the intermediate channel with the help of connecting clips and 12.5 mm dry wall screws at 230 mm centre to centre distance. Finally, the 12mm thk. Gypsum boards shall be fixed to the metal frames and the tapered/square edges of the boards shall be finished to a flush joint with requisite filler, paper tapes, finisher and primer suitable for Gypsum plaster boards, (as per recommendations of manufacturers, Indian Gypsum or equivalent) including Acrylic Emulsion Paint of approved make and shade and colour. The rate shall include the cut-outs to be made for light fittings, grills, diffusers, speakers, smoke detectors, sprinklers etc. with provision of the frame along perimeter of the cut outs/ opening with channels/ ply to support the ceiling adequately as per the directions of Architect. The rate shall include necessary shapes, designs, patterns in curvature, sloping, dome, oval & eliptical shaped etc including the necessary provisions of coved lighting scheme etc complete as per the designs, drawings and instructions of the Architect.

Mineral Fibre Board False Ceiling - Providing and erecting false ceiling of Mineral Fiber ceiling Board of approved make with framework, runners, cross runners & suspenders from the existing ceiling as per the manufacturers details and specification and 600X 600mmX 15mm thk tiles of approved design, texture & in microlook pattern including the grids in black / white silhoutte pattern, 15mm as per manufacturers specifications complete including making necessary cut-outs for electrical fixtures, AC diffusers, access etc as per the instructions of the Architect. Approved preminum Tile in Dune RH Microlook or equivalent approved category with black silhouette locking supporting system, 15 mm grid. The rate shall also include Providing & Fixing in position 50 mm high Axiom with all its associated Accessories as per manufacturers specifications & standards etc complete. Rate to also include providing & fixing additional 6mm thk. commercial ply backing on mineral fibre modular false ceiling tiles of support light fitting, speakers, CCTV cameras in grid work wherever directed

Providing & Applying Plaster of Paris Punning up to average thickness of 12 mm thk. on existing walls to proper level & plumb, including Groove Complete as per site conditions & directions of the Architect.

Providing & Applying gypsum Punning up to average thickness of 12 mm thk. on existing walls to proper level & plumb, including Groove Complete as per site conditions & directions of the Architect.

Providing and erecting in position Plaster of Paris Cornices 3" x 3" in size to the false ceiling. Including filling the gaps with POP & painting the same with Acryllic Emulsion paint of approved colour and texture as per instruction of Architect.

Providing & Fixing high end & premim class Roller Blinds of approved make with supporting framework etc of approved shade & colour, opaque eclipse type complete in all respects & working order with triple spring arrangement as per manufacturers specifications & standards & directions of the Competent Authority. The cost towards automation & automatic motorized openings shall be considered in automation estimates, however the roller blinds installed shall have provision for synchronization to automation system. (Basic rate of Roller Blinds shall be Rs. 120 / Sq. Fts plus taxes {GST})

Providing & Fixing Vertical Venetian Blinds 4" wide of' approved make, shade, texture in two colours with supporting framework and assembly complete in all respects & working order with triple spring arrangement as per manufacturers specifications & standards & directions of the Competent Authority.

Providing & fixing pelmet for blinds in 19mm BWR IS 303 grade 19mm Thk Plywood finished with laminate internally as per architects design/details/ instructions. 150 mm X 300mm.

Providing and fixing high end, premium quality, reflective designer frosted film of Llumar/ 3M or equivalent approved make and shade to be fixed to glasses of all types, windows, partition glasses, panelled glass surfaces etc complete as instructed by Architect.

Providing and fixing high end, premium quality, reflective designer printed film of Llumar/ 3M or equivalent approved make and shade to be fixed to structural glazing glasses or glasses of all types, windows, partition glasses, panelled glass surfaces etc complete as instructed by Architect.

Artificial Plants - Providing and supplying large size artificial plants such as moss, fern, cactus etc including necessary stand for holding the plants as approved by Architect.

Providing and supplying medium size artificial plants such as fern, moss, cactus etc including necessary stand for holding the plants as approved by Architect.

Providing and supplying metallic containers for Artificial plants of approved design and make

Providing signage boards of total height of minimum of 12" comprising of desired numbers of alphabets / characters in SS of desired heights, indicating the various departments of the office on Stainless Steel sheets and fixing the same to the required positions etc complete. (1 No of signage board comprising any number of alphabets / characters shall be considered for the purpose of making payment)

Providing Name Plate of size 375 X 150 mm in brass and fixing the same to the required position. Thickness of plate engraved with brass letters shall be 3mm.

Providing and fixing 10mm thk toughened plain glass to be fixed to the stainless steel railing on D-brackets & approved SS-Glass patch type, spider or compatible fittings & fixtures as per direction of Engineer In charge to the required shape and size. Two pulsed infrared photoelectric beams (Hold-open) to be mounted in jambs. The entire door unit shall be in plumb, level, true in line & shall be weather tight with sealand/joing filler/gaskets. The Door unit shall be installed in coordination with wall flashings & other components of construction.

Providing & Fixing in position FULL HEIGHT 100 MM thick PARTITION WITH DOUBLE LAYER GYPSUM ON BOTH SIDES - 50mm x 25mm x 1.6mm size over Aluminium FRAME WORK. Partition from Finished flooring level till true ceiling level. Framework - Providing and fixing of 50mm x 25mm x 1.6mm size Aluminium partition placed at 610mm centre to centre in horizontal & Vertical with joints staggered to avoid leakage through joints. has to be provided at the horizontal joints of the two boards. Provide an additional salwood member at the true ceiling level and sub frames for doors and glazed openings while fixing the frame work as per details. Cladding / Skinning - The framework to be skinned / cladded on both sides (till the false ceiling) with DOUBLE layers of 12.5 mm thick tapered edge gypsum board ON BOTH SIDE (IS-2095/1982) in line and level screw fixed with 25mm & 35mm drywall screws @ 300mm c/c with staggered joints to avoid leakage through joints and finished with proprietary supplied jointing tape to have flush look which includes filling and finishing with jointing compound paper coat as per manufacturer's specification. Joints to be sand papered to achieve a smooth and seamless finish. Care must be taken that the plasterboards are raised 3mm from the floor and in this gap, cheeking compound is injected, for successive layers and similarly for the true ceiling channel. Gypsum partition to be installed as per India Gypsum specifications. Supply, Installation and Fixing 50mm thick glass wool of density 48kg/m3 wrapped in RP Tissues. The glass wool to be filled in the cavity between the framework and Gypsum skins. Rate to include gluing insulation to first board at multiple points and then bracing the insulation with the help of GI wires. Special Provisions Contractor to make provision for any MEP Services boxes/ conduits or other components in addition to electrical / networking required in the partition and to provide dia cut-outs as required. Electrical / Network boxes/conduits / or other components in addition any services to be provided at desired height and location as indicated in the drawing with Ply backing. The cost of groove to be included in the rate of the partition for all junctions between materials, columns, walls, etc. to have necessary 6mm groove as per details Contractors to provide At all locations where services are penetrating the partition above false ceiling to have salwood frame work around the duct/cable tray/pipe and the gaps between the frame work and service to be filled with appropriate fire stop material as directed and also submit the DB level report after the works are completed

Supply & Installation of Crystal Glass film 8150 OPTICALLY CLEAR with approved artwork, cut using digital plotter and print ( latex ). Self-adhesive, bubble-free installation to be done on clean glass , by Authorized Installers only.3M Architectural Markets. 3M interior warranty for a period of 3 years for Interior application to be submitted along with invoice by 3M directly to the customer.Rs. 2260 per sqmtr.

Providing and fixing of Matt natural anodized aluminium skirting profile of 75 mm height inclusive of 12mm thick ply backing wherever required, and with all accessories and installation as per the manufacturers specifications. Rate should include preparation of surface. The skirting shall be fixed as per details & Architects instructions.

Providing & Suplying 12mm thick medium duty PVC foot mats for all floor entries, main entrance & toilet entries of approved make. (Basic Rate of Foot Mat shall be Rs. 2000/- per Sqmt.)

ACOUSTIC PANELS (CNC SCREEN ROUTING AND GROOVING) 12mm thk - SUPPLY & FIXING in position of 100% Wool CNC Cut Grooved Felt Top Acoustic Panels make 12mm (thk) for reducing and controlling Reverberated noise with a NRC of 0.5 mm , Panel Composition 100% Wool on PET Base to be minimum 50% Recycled with LOW VOC which addresses life cycle impacts such as Toxicity. Acoustic board to be fixed on a backing of 12mm thk. commercial ply. Size of Panel 1220 x 2400mm / 2900mm with thickness of 12mm , weight 2350gsm, Density 235 kg/m3. Acoustic NRC 0.30 for Direct Fixing on Wall, 0.45 with a 14 mm AirGap, 0.50 with a 24 mm Air Gap. To be used for Wall Panelling, Wall Screens and Ceiling Panels.

ACOUSTIC PANELS 12mm(thk) (PRINTED) - SUPPLY & FIXING in position of 100% Wool Printed Felt Top Acoustic Panels make 12mm (thk) for reducing and controlling Reverberated noise with a NRC of 0.5 mm , Panel Composition 100% Wool on PET Base to be minimum 50% Recycled with LOW VOC which addresses life cycle impacts such as Toxicity. Acoustic board to be fixed on a backing of 12mm thk. commercial ply Size of Panel 1220 x 2400mm / 2900mm with thickness of 12mm , weight 2350gsm, Density 235 kg/m3. Acoustic NRC 0.30 for Direct Fixing on Wall, 0.45 with a 14 mm AirGap, 0.50 with a 24 mm Air Gap. To be used for Wall Panelling, Wall Screens and Ceiling Panels.

Providing & installation of Natural Plants with basic pots to be placed inside the container boxes. All pots will be with Pot-in-Pot mechanism OR Base plates to avoid water leackage. Leca balls for Top dressing, Fillers to raise the height etc complete including digital meters, thermometers, humidity meters, gauges etc complete

Providing & installation of Natural Indoor Plants - Healthy & Bushy Plant (as per mockup / Images) - Potting Soil, Compost & Coco-peat for plantation - Plant Varieties etc complete including digital meters, thermometers, humidity meters, gauges etc complete

Providing & fixing of Ceiling Baffle Pet Panels. The Shape, Size and thickness can be customized as per Architects directions and requirement. (Rates are including Hardware and Installation) It will be fixed on Thread Bar and C Channel Suspension System. Size - 24mm(thk) x 100mm(h) x 2400mm(l) & fixing at 200 mm c/c

Providing & Fixing of Ceiling Clouds (Shapes) The Shape, Size and thickness can be customized as per Architects directions and requirement. (Rates are including for Clouds and 4 Sets of Wire Rope Hanging Hardware with Installation) It is To Be fixed on Wire Ropes. Support Stiffner to be considered. Size 1200mm x 1200mm x 24mm(thk). & 2400mm x 600mm x 24mm(thk).

Providing & fixing Endura Swimming Pool Tiles (247x122x8mm) Olympic grade as per FINA standards in floor & walls approved polymer adhesives & grouting materials, as directed by the Engineer-in-charge, including self supporting scaffolding etc complete

Providing & fixing 30mm thk flame finished Granite stone in flooring with 50 mm thick cushioning including grooving, etc. complete as directed by Engineer.

Providing & fixing in position S.S Railing of 32 mm dia (OD) 316, fixing with anchor bolt etc. Rate shall include providing & fixing of S.S bracket for pedestal of 25mm diameter 316 with anchor bolt etc complete

Providing, Supplying & fixing 0.45m X 0.45m internal size of rectangular composite resin grating and frame (with minimum waterway areas 35% of internal size) of approved brand with grade designation C250 as per EN-124 standard with bolt and lever type locking arrangement. The gully gratings & frame shall have top abrasion resistant layer conforming to IS15658:2006 and pemissible permanent set value of 1.5 mm after the application of 2/3 test load in five continuous applications as per EN124, the testing shall be performed in fully equipped and NABL certified test lab with random batch test (2% of lot size) as per testing procedure stated in EN-124 standard, including testing, inspection of material sample and finished product in presence of the Engineer in charge at Manufacturer's work, etc. complete as specified and as directed by Engineer-inCharge. (Inspection shall be as per guidelines of IS and EN-124 standard specifications)

Providing, Supplying & fixing 0.60m X 0.50m internal size of rectangular composite resin grating and frame (with minimum waterway areas 35% of internal size) of approved brand with grade designation C250 as per EN-124 standard with bolt and lever type locking arrangement. The gully gratings & frame shall have top abrasion resistant layer conforming to IS15658:2006 and pemissible permanent set value of 1.7 mm after the application of 2/3 test load in five continuous applications as per EN124, the testing shall be performed in fully equipped and NABL certified test lab with random batch test (2% of lot size) as per testing procedure stated in EN-124 standard, including testing, inspection of material sample and finished product in presence of the Engineer in charge at Manufacturer's work, etc. complete as specified and as directed by Engineer-inCharge. (Inspection shall be as per guidelines of IS and EN-124 standard specifications)

Providing & Laying dry stone Rubble Soling with average 230 mm size hard stone set in regular lines, handpacked and interstices thoroughly filled with small chips including filling in with good quality murum brought from outside, compacting with iron rammers, watering, sand spreading 12mm thk. layer of grit on top etc complete as directed by Engineer In Charge. (Note: The rate includes the royalty and other taxes if any)

Providing and constructing discharge ring well of 1.5m dia and depth upto 6m made of RCC pipe collar including excavation and stacking the soil and disposing as per the instructions of engineer-in-charge, pumping of water, lowering the collars by means of lifting tackles and filling with gravels and boulders from outside of the circumference of the collar so as to allow infiltration of ground water inside the well through the gap between the collars

Providing and applying 12 mm thick internal ceiling plaster with neeru finish by using ready-mix Roofit mortar as per manufacturers recommendations at all heights and locations for masonry (except stone masonry) and concrete surfaces including racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc. complete.

Providing, detailing, composite fabricating members like Trusses, Girders, bracings, supports, purlins, runners, and similar structural steel members fabricated using M.S. hollow tubular steel sections (Circular & rectangular pipes), including bolting, welding, cutting, fabrication etc complete

Design Supply & Installation PVC Coated Fabric Ferrari 902S For Tension membrane Roofing (Tensile Fabric roofing) to be supported using M.S frames, hollow tubular sections (Rate of MS frames & sections shall be paid for separately under the relevant item herein above) etc complete as per manufacturers standards and specifications.

Providing and installing crystalline waterproofing treatment to inside surfaces of the water retaining structures. VERTICAL SURFACES : a) Treatment shall consist of preparation of surfaces including ‘V’ grooves at junctions and joints, pressure grouting the same and curing for specified period. b) Applying two coats of approved crystalline waterproofing compound at specified intervals as recommended by manufacturer and as directed bby Engineer-in charge and allowed to cure. c) Extra for Plastering of walls and finishing smooth with 15 mm thick cement mortar 1:4 (1 cement : 4 fine sand) admixed with approved waterproofing compound in recommended proportions.

Providing waterproofing treatment from outside to basement lift-pits and other under ground structures during construction. The treatment shall be started after the P.C.C. bedding for the base slab or raft slab is laid. On the P.C.C. bedding a waterproofing layer based on cement with rough shahabad stones of 20 to 25 mm thick well pointed in the joints with 1:3 C.S. 40 mm thick for floors and 20 mm thick for sides with cement float and water proofing compound as per specifications shall be laid. Then the surface shall be superimposed by regular R.C.C. raft or base slab as per design. After completion of the raft / base slab and side walls the treatment of waterproofing layer shall be continued along the outer surface of the walls upto a height of 30 cm above the adjacent ground level. (The excavation of the side around the walls shall be filled with soft earth by the contractor). The total thickness of the treatment shall be 65 mm to 75 mm for floors and 32 mm to 38 mm for walls.

Design, Supply, Installation Testing, Commissioning, Of Swimming Pool and its filtration plant of size 25 Mtr x 17.50 Mtr - Filter Vertical type (imported) Totally anticorrosive Imported filters 2.0m dia manufactured with fibre glass and polyester resin fitted with collector arms and diffuser made from unplasticised PVC and polypropylene. 100% Anti-corrosive internal Gelcoat resistant to even salt water. Filter supplied complete with lid in polyester resin and fibre glass, manual air purge cap for sand discharge and PVC flange connection for inlet and outlet complete with necessary pressure guages. Filter manufactured using state of the art production technique to ensure toughness durability and easy to maintain and in conformity with International Standards

Supply & filling of Filter media Silica Sand/White quartz for filter with granulometry between 0.4 and 0.8mm

Supply & filling of Filter media Silica Sand/White quartz for filter with granulometry between 1.0 and 2.0mm

Suuply & fixing in position Frontal piping valves 160mm dia PVC frontal piping & fittings comprising bends,tees, for filter including valve batteries, i.e. 5 Nos, 150mm dia Butterfly valves for inlet, outlet upwash, washout, rinse with flanges supports wherever required etc. complete set.

Suuply & fixing in position Circulating pumpsets 120 M3/HR pump set at about 12 to 15 mtr. Head (7W+1 SB) casing : CI Motor Details : Type : Squirrel cage Enclosure : TEFC speed in RPM : 1450 Rated Voltage/frequency 415 V+/-10 The work comprising of suction piping, valves, suction & delivery piping, delivery vales and NRV etc as per specification

Suuply & fixing in position Alum Dosing plant including electronic dosing pumps, with fittings etc. complete, 100 ltr Sintex tank and stirrer. Electrical : 230 V.A.C. 50 HZ Suction/Discharge Tubing : 4/6mm Material Of Construction. Pump Head : Glass filed PP Diaphragm : Teflon Connectors : Glass filled Polyproplene Suction tubing : HDPE Discharge tubing : HDPE Flow :10lph This will be injected into pump delivery header

Suuply & fixing in position Soda Ash dosing plant including electronic dosing pumps, with fittings etc. complete, 100 ltr Sintex tank and stirrer. Electrical : 230 V.A.C. 50 HZ Suction/Discharge Tubing : 4/6mm Pump Head : Glass filed PP Diaphragm : TeflonConnectors : Glass filled PP Suction tubing : HDPE Discharge tubing : HDPE Flow : 10lph. This will be injected into pump delivery header Including materials and labour charges.

Suuply & fixing in position Ozone Plant of capacity 35 to 45 grams per hour approximately type corona discharge air cooled or water cooled (SS 316 Finned for air cool/jacketed for water pool) including ozone indicator, rotameter, oxygen flow 1-5 LPM all contact parts in SS 316 ozone tube of silicon, teflon, complete. a No. Oxygen Generator flow about 5 LPM, 02 pressure 7 Psi in built air compressor, complete and Supply, installation, testing and commissioning of Control Panel for ozone generating equipments with Electric Wiring & Cabling and all other accessories to run the system etc as per specification

Suuply & fixing in position Gaseous Chlorinator of vacuum type capacity 5 kg/hr with control valve, vacuum chamber, flow meter, etc. along with one set of suction and delivery piping with valves for 1 No. 3 HP Booster Pumping set with Starter along with 2 Nos. gas cylinder including materials and labour charges

Providing and erecting in position Test set P.H. Test Set, Chlorine Test set for Swimming pool

Providing & Fixing in position SUCTION SWEEPER : Trolley mounted suction sweeper self priming pump with 2 HP motor with rubber tyred wheel, handle, 3 ft long suction sweeper head with brush, handle, wheels, rubber squeegees, towing rope, 30 Mtr length and 4 core flexible cable with industrial plug along with deep bag net and curved brushes and other maintenance accessories like handle etc.

Providing & Fixing in position Main Drain Arrangement : - S.S. Main Drain with nut bolts, pvc drain piping from deepest end of pool to the suction of pump with valves as per specifications

Providing & Fixing in position Pool Piping : Piping Work inside pool floor for fixing inlet nozzles, Circulating piping : PVC piping from filter to shallow end of pool. Water distribution piping network :- a) From Balancing tank to pump b) From pump to filtration system c) From Filtration plant to swimming pool and with necessary valves and accessories d) From Swimming pool to balancing tank. System shall also include 50 Nos PVC inlet nozzles inside the pool as per specifications.

Providing & Fixing in position LADDER Overflow model staionless steel AISI-316 ladder, width 500mm handrails dia 43mm stainless steel non slip steps, and anchoring fixtures no

Providing & Fixing in position Life Buoy with SS Supports :-Life Buoys of size 400mm dia in orange hard plastic with rope and life buoys support as per specification

Providing & Fixing in position Life buoy holder made from aluminium, complies with EN 12145 for attaching to wall or rail including cuffs for attaching to rails 9

Providing & Fixing in position Life guard loop made of stainless steel with butterfly nut which can be connected the telescopic handle

Providing & Fixing in position SS Hand Rail SS 304 Grab rail 40mm dia duly buffed and mirror polished alongwith supports

Providing & Fixing in position Extensible handle 13 m for attachment to the life guard loops in anodized aluminium.

Providing & Fixing in position Starting Blocks 700 mm high starting blocks with base in stainless steel AISI-316, 500 X 500MM platform slopping at 5 degree and making an angle of 5.5 degee with the ground in polyester & fibre glass with non slip finish complete with fixing shall be provided for each lane Each starting block shall be anchored on the deck with the help of 43mm SS 315 anchor starter blocks shall have nummesequence

Providing & Fixing in position BADMINTON POST :- Stylish Design, Made From 40X40 mm steel square tube with 60kg. of ballast weight. Roller Wheels are provided to facilitate easy transport and storage. This is designed for strength and stability, to support heavy net. with a large base maintain the stability.

Supply & fixing of 6 mm thick RECREATION-60 synthetic sports surface consisting of 100% pure vinyl wear layer of 1.5 mm thickness, upper surface treated with protecsol to reduce Skin burn and Sanosol treatment to avoid fungal growth. Double fiber glass grid for sound stability on floor with width of sheet is 1.5mts, joined with seamless hot welding laid with double marking tape as per manufacturer’s instruction over existing leveled surface including game lines marking with following specification. Technical Specification:- Shock absorption under EN 14808 standard not less than 25% Ball bounce under EN 12235 standards not less than 90% Abrasion resistance under EN ISO5470-1 < 350mg. Approved by :- FIBA (Federation International Basketball Association), WBF (World Badminton Federation). (International Handball Federation) IHF (International table tennis federation), ITTF (Federation of international Volleyball) FIVB

Supply, installation & finishing of free floating resilient wooden sports flooring system of make Prestige/ Robbins sports floor/ connor sports flooring/ Zyrex/sunflex or equivalent made of 20mm thick Teak Wood floor boards in width of 58 to 83mm and random lengths with tongue and grooved shape and under frame made of Canadian Pine wood in size of 60mm x 38mm fixed with 18mm thick Bio-Cush EPDM rubber shock pads. The floor will be installed after giving anti-termite treatment to the IPS sub-floor and placing vapour barrier. After installation the floor will be machine sanded and finished with three coats of imported non-skid polyurethane lacquer all complete as per international standard and quality with a total height of 76mm. Game line marking to be carryout in approved colours.

Dumbbells Rack 2 Tier - Structure and Frames: Structural frames are fabricated from 100 x 50 x 2.5mm thick square steel tubing. Heavy metal bending design is used to ensure superior strength and to eliminate joint failure. Hardware: Hardware used are Button Head Bolts and made up of high tensile steel. Powder Coating: All components are chemically treated to seal exterior and interior surfaces against corrosion. The components are electro statically powder coated at minimum 60-70-micron thickness to make it resistant to scratch, corrosion and humidity. High Quality Rubber Grips should be used. Closing Caps: All open ends are covered with Nylon/PP closing caps. Foot Pad: High quality rubber foot pad.

Weight plate Rack - Structure and Frames: Structural frames are fabricated from 100 x 50 x 2.5mm thick square steel tubing. Heavy metal bending design is used to ensure superior strength and to eliminate joint failure. Hardware: Hardware used are Button Head Bolts and made up of high tensile steel. Powder Coating: All components are chemically treated to seal exterior and interior surfaces against corrosion. The components are electro statically powder coated at minimum 60-70-micron thickness to make it resistant to scratch, corrosion and humidity. Closing Caps: All open ends are covered with Nylon/PP closing caps. Foot Pad: High quality rubber foot pad.

Barbell Bars - 28mm/50mm Mild Steel Chrome Plated Barbell Bar (2.5’ to 10’ft)

Imported Hexagon Rubberised Dumbbells - DUMBBELLS: Imported Hexagon Rubberized Dumbbells

Rubberised Weightplate - WEIGHT PLATES: Imported Rubberized Weight plate

Treadmill - Spacious Running Surface Belt Size- 22" W x 62" L (56cm W x 157.5cm L) Drive Motor3.5 HP Continuous Duty. AC Belt Type Multi-ply polyester belt with PVC non-slip surface Incline Motor1000 lbs. (453.6 kg) thrustRollers3.0" (7.5cm) crown rollers keep belt centered. Speed0.5 - 12 MPH (0.8 - 20 KPH)Incline0 - 15%Deck Suspension for Independent Compression ShocksDeck1" (2.54cm) melamine laminated reversible deck medium-density fiber board. Dimensions80.5" L x 33.25" W x 61" H (204.5cm L x 84.4cm W x 154.9cm H) FullStep-Up Height8" (20cm)Max. User Weight400 lbs. (181.4 kg)Net Weight368 lbs. (167 kg)Gross Weight390 lbs. (176.9 kg). Display AreaLarge 6.5" backlit multi-color LCD screen with scrolling alphanumeric messaging. Three additional LED displays with readouts for time, speed, and incline. Programs- name, date and time, workout time, calories, step count, distance, heart rate, speed, incline and pacePrograms2 heart rate programs, 2 customized user programs and 17 preset programs (5 weight management, 5 healthy living, 7 sports training).

Spin Bike - Length: 104cm / 41” Width: 64cm / 25” Height: 119cm / 47” Weight: 46Kg / 101 lbs. Recommended maximum user weight: 105Kg / 232 lbs. Flywheel weight: 18Kg / 40 lbs

Gym Matting 2ftx2ftx16mm - Gym Matting made up of EVA with JSR Technology and interlocking system Dimensioning 2ftx2ftx10mm.

Mirror - Mirror for gymnasium with aluminum fixation on all four side (2’x4’ to 8’x 8’)

Swiss Ball - Gym ball for back exercises and posture correction With Inflatable pump included in the package. To be used for abdominal exercise and other aerobic exercises Anti-burst gym ball. (Size 65cm, 75cm and 85cm)

Yoga Mat - Thickness: 10mm Color: Blue or any Non-slip surface Very soft material for extra comfort Dimensions: 180 x 60 x 1cm Makes exercises and yoga more comfortable and easy.

Locker - Lockers made by M.S. CR Sheet of 18gauge, complete locker cabinet dimensioning 6ft X 6ft, each locker of size 1ft X 1ft X 20"inch depth. 20-shelf in each cabinet

Supplying, installing, testing and commissioning 11 kV 630A, indoor type ring main unit with 1 VCB & 2 LBS with internal arc compliance complete erected on provided CC foundation/MS channels/trench, etc., as per specification no SW-HTS / RMU of make as approved by Goa Electricity Department

Supplying, erecting, testing and commissioning 11KV HT metering cubical (compact / vertical type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle, painted with powder coating / epoxy paint of required shade, copper bus bar size 25 x 6 mm, heavy duty mechanical lock, with counter meter for measuring no of times the opening of meter door, top side cover (CT, PT cover) interlock with meter door, epoxy casted 3 nos. CT having required ratio between 10/5A to 50/5A, VA10 or 15, Class 0.5S, epoxy casted 3 nos. PT having ratio 11000/V3/110/V3 VA 50, Class 0.5 suitable for provided trivector meter, and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation of make as approved by Goa Electricity Department.

Supply, installation, testing and commissioning of 500kVA, 11/.415kVA, 11/.415 volts Deta/Star, vector group DYN11, outdoor mounting, oil cooled, ONAN transformer with On Load Tap Changers (OLTC) having AVS relay and RTCC for automatic sensing of incoming voltage, automatic operation of OLTC and facility for remote manual operation of OLTC, suitable for incoming voltage variation of +5% to –15% in equal steps of 2.5 % to give a constant secondary voltagee. The transformer shall be provided with fittings, accessories, protection, first filing of oil etc. including Buchholz oil temperature alarm/trip protection in LV chamber complete as per specifications and as required. The transformer shall be provided with arrangement to terminate XLPE cable on HT side and to connect Aluminium Bus Duct /Cable on LT side, complete as required. The Transformers shall confirm to IS: 1180 Part-VI & IS 2026.The losses of the Transformer should be as per latest ECBC guideline.As per Latest IS:1180 & Transformer efficiency type -2. It should be compatible with IBMS in all respect .Necessary items as required to form part of transformer.

Supply of following size of 3 core, HV, 11 KV grade, ISI mark, XLPE cable with stranded compact circular aluminium conductor, conductor screened with extruded semiconducting compound, XLPE insulated, insulation screned with extruded semiconducting compound in combination with copper tape(0.3 KA for 1Sec.) cores laid off,inner sheath of PVC tape,galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS:7098(Part II) with latest amendments. 3 Core 300 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed lenghtwise on top of cable all over the run and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) Rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV grade of size not exceeding 400 sq.mm direct in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required.

Supplying and making Indoor cable end termination with heat shrinkable kit for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable upto 11 KV grade, complete as required. (d) 11 KV, 3 Core x 240 - 300sq.mm

Supplying and making Outdoor cable end termination with heat shrinkable kit for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable upto 11 KV grade, complete as required. (d) 11 KV, 3 Core x 240 - 300sq.mm

Indoor Hall - Swimming Pool Panel. Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. - 200Amp.35 ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & earth fault protection. Bus Bar Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz.,250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 200 amps, 415V 4P MCCB '35kA' with overcurrent and short circuit Thermal based release.- 1 No. & 1 Spare. 40A DP MCB '10kA' -9 No.

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 300 sq.mm

3 1/2 Core 240 sq.mm

31/2 Core 185 sq.mm

3 1/2 Core 120 sq.mm

3 1/2 Core 95 sq.mm

3 1/2 Core 70 sq.mm

3 1/2 Core 50 sq.mm

3 1/2 Core 35 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 10 sq.mm

3 Core 6 sq.mm

3 Core 4 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 25 sq.mm

4 Core 16 sq.mm

4 Core 10 sq.mm

4 Core 6 sq.mm

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (11) 3 1/2 x 300 Sq. mm.

(10) 3 1/2 x 240 Sq. mm.

(8) 3 1/2 x 185 Sq. mm.

(6) 3 1/2 x 120 Sq. mm.

(5) 3 1/2 x 95 Sq. mm.

(4) 3 1/2 x 70 Sq. mm.

(3) 3 1/2 x 50 Sq. mm.

(2) 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (4) 3 x 10 Sq. mm.

(3) 3 x 6 Sq. mm.

(2) 3 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. (6) 4 x 25 Sq. mm.

(5) 4 x 16 Sq. mm.

(4) 4 x 10 Sq. mm.

(3) 4 x 6 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable)and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (b) In rocky strata

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20 mm Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement (plumbing will be paid seperately). (b) In rocky strata

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). (b) In rocky strata

Providing and fixing 25 mm x 5 mm copper strip on surface r in recess for connections etc. as required.

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for connections etc. as required.

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required.

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop earthing as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc as required.

Supply, assembly, erection, connecting, testing & commissioning of LT weather proof dust and vermin proof, outdoor feeder pillar, fabricated out of suitable sized angle iron and flats and covered with 3mm thick CRCA sheet steel including canopy, duly stove enamel painted, both sides (front and rear) openable with locking arrangement, rubber gasket cable glands, etc. Bakelite phase separators and bus bar supports including RCC 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) foundation, 450 mm deep and 150 mm above the ground. The feeder pillars shall be complete with 3 phase and neutral bus bars of capacities as described below and moulded case circuit breakers (MCCBs) with adjustable overload relay, copper FRLS control wiring with 1.5sq.mm, complete in all respects as per specifications as required. INCOMING:- 63A 4P MCCB (25ka) with thermal magnetic release & rotary handle - 1no. 3 Phase and neutral (100%N) aluminium bus bars of 150/ 100 amps. Capacity. OUTGOING:- 70 AMP. TP CONTACTOR WITH NO/ NC CONTACTS -1 set 24 HOUR TIMER - 1 set. 32A 4P MCB (10ka) - 7 nos. 16A DP MCB (10ka) - 7 nos. 63A 4P MCB (10ka) - 4 no. 16 AMP. SWITCH & SOCKET - 1 no. with in the feeder pillar. 16 AMP. SWITCH & SOCKET - 1 no. with in the feeder pillar

Supply, assembly, erection, connecting, testing & commissioning of feeder pillar with 1 no 32 A TPN MCB as incommer and 6 nos 16A TPN MCB as outgoing with suitable terminals

Supplying and erecting LED Panel Light (600mm X 600mm) Max. 30 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min. 3600 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete. Lights of Make Philips/Crompton/Leksa/Wipro as directed by engineer incharge

Supplying and erecting integrated LED flood light fitting Max. 100W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 12000 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L70B50 including driver with U shaped bracket Lights of Make Philips/Crompton/Leksa/Wipro as directed by engineer incharge

Supplying and erecting LED square / circular Max. 18 W down lighter /Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete .Lights of Make Philips/Crompton/Leksa/Wipro as directed by engineer incharge

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete.Lights of Make Philips/Crompton/Leksa/Wipro as directed by engineer incharge

Supplying and erecting integrated LED street light fitting 130-140W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 15600 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140 270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete Lights of Make Philips/Crompton/Leksa/Wipro as directed by engineer incharge

Providing & erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm A/F, top 70 mm A/F on provided foundation.of make VALMONT/TRANSRAIL/UTKARSH as directed by Engineer incharge.

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball

Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball

Making M-20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal/conical GI pole).

Supplying and erecting 16 m (clear height) motorized high-mast (Top-150mm,Bottom-410 mm) hot dipped galvanized material with average minimum thickness 65 micron, made from high tensile structure grade steel as per BSEN -10025 S 355/E350 & 3 mm thickness, with base plate 25 mm thick x OD 570 mm grade as per IS-2062, pole made in single section & submerge arc welded, with lowering & raising motorized unit, wire rope stainless steel 316 grade 2 nos., 7x19 construction 6 mm, SG-DG U clamps, double drum winch assembly 350 kg, 5x2.5 sq.mm flexible copper cable with lantern carriage assembly suitable for max. 16 nos. luminaires and its control gear box, supply and fixing of lightning arrestor,supply and fixing aviation light. (The high-mast with serial number, factory inspection report/test report of high-mast should be provided) as per specifications on provided foundation J type stud/bolts with necessary High Mast of Make Valmont/ Transrail/ Utkarsh/Ventura as directed by the depatment.

Supplying and erecting outdoor stand mounted feeder pillar for high-mast of the same manufacturer with 63A TPN MCB incomer, 24hr astronomical time switch with minimum 5 Years battery backup, , IP 54 and IK10 protection, 45 A TP contactor for automatic switching of luminaires, 2 no 9A contactors and raise/lower push button, and provision for termination of adequate size of incoming and outgoing cables complete erected in min. 14 SWG CRCA sheet box powder coated with supporting angles, self lock, gasket and slanting top erected on CC foundation complete

Making M- 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design submiited by the High Mast Manufacturer approved by the department with required steel, concrete etc.

Supply and fixing in position 1000mm wide checkered rubber matting of 11KV grade as per electricity rules,with thickness not less than 12mm.

Supply and fixing in position the best quality L.T. Danger Notice plate of 200mm x 150mm,made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the best quality H.T. Danger Notice plate of 250mm x 200mm made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the approved shock treatment / restoration charts written in Hindi and English duly framed in teak wood frame and covered with 2.8mm glass as required.

Supplying and fixing of fire buckets 5 Nos.in each set of approved quality, red painted from outside and white from inside conforming to IS : 2546/1974 with additional handle at the bottom, filled with fine sand and fixed on an angle iron frame as per the requirement of local authorities.

Supplying and fixing of MS pedestal stand suitable for supporting four buckets as required.

Supplying and fixing First Aid Box of 18 S.W.G. M.S sheet,painted as approved & prescribed by Indian Red Cross Society & as per attached specifications.

Supplying and fixing of caution Boards of 16 S.W.G. , M.S. sheet of 300 mm x 150mm size, duly painted & having "MAN ON LINE' & "DO NOT SWITCH ON' written in Red complete with hanging arrangement as required.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size glass framed and installed in main switch room.

Supply of tool kit with 1 pair,11KV rubber hand gloves of aproved make.

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 100 mm dia pipe

150 mm dia pipe

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. 100 mm dia ID

200 mm dia ID

300 mm dia pipe

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required 90 mm dia (OD-90 mm & ID-76 mm nominal)

120 mm dia (OD-120 mm & ID-103 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

Providing, Supplying and Installing Omni Direction wind turbine with Wind accelator capacity of 2KW equivalent, Multi phase, multi Voltage system whose system voltage DC12V-48V/AC 230V, 50Hz,, Peak power 2000W, Material Aluminium/ steel with waranty of 2 Years and opertional life 25 Years of approved quality confirming to IS standards.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed steel conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (c) Group C -- with Cat A Modular Accessories

Wiring for 5A /15A power plug with 2 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in recessed steel conduit(heavy) alongwith 1 No 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for 5A /15A power plug with 4 x 4 sq.mm FRLS PVC insulated copper conductor single core cable in recessed steel conduit(heavy) alongwith 2 Nos of 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed steel conduit(heavy)of appropriate size as required. (a) 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earthwire (20mm Conduit)

(b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

(d) 2 x 6 sq.mm + 1 x 6 sq.mm earthwire (25mm Conduit)

(e) 2 x 10 sq.mm + 1 x 10 sq.mm earthwire (25mm Conduit)

(k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

(l) 4 x 16 sq.mm + 2 x 16 sq.mm earthwire (40mm Conduit)

Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/ wooden block including connections etc as required.

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (a) Cat A

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 4 nos 3 pin 5/6 A modular socket outlet and 4 nos 5/ 6 A modular switch connection painting etc. as required. The scope of work includes alternate arrangement, if required as per site conditions, to provide switches and sockets seperately, above and below the table respectively. ( For workstations) (a) Cat A

Supplying and fixing 20 A 240 V SPN industrial type socket outlet with 2 pole and earth metal enclosed plug top alon with 20 A, C series SP MCB in sheet steel enclosure in surface or in recess with chained metal cover for the socket outlet and complete with connections testing and commissioning etc. as required" (a) Cat A

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. (a) 20 mm

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required (a) Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator) (n) 8 way double door Cat B

(o) 12 way double door Cat B

(p) 16 way double door Cat B

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (b) 4 way (8+12), double door, Horizontal type Cat A

(c) 6 way (8+18), double door, Horizontal type Cat A

(d) 8 way (8+24), double door, Horizontal type Cat A

(e) 12 way (8+36), double door, Horizontal type Cat A

Supplying installation testing and commissioning of surface/ recess mounting vertical type 415 V TPN, double door MCB DB of sheet steel dust protected duly phosphatised and powder painted inclusive of 200 A tinned copper busbar common neutral link earth bar din bar for mounting MCBs detachable gland knock out plate and with 100 A 10 KA MCCB as incomer interconnection between incomer MCCB and busbars of following ways (but without MCCB/MCBs as required) (b) 8 way with 100A MCCB as Incomer, double door, Cat A

(c) 12 way with 100A MCCB as Incomer, double door, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. (a) SP MCB, Cat A

Supplying and fixing following rating double pole 240 V isolator in the existing MCB TPN complete with connections testing and commissioning etc as required (a) 40 A, Cat A

(b) 63 A, Cat A

Supplying and fixing following rating four pole 415 V isolator in the existing MCB TPN complete with connections testing and commissioning etc as required (a) 40 A, Cat A

(b) 63 A, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

(b) 40 A, Cat A

Supplying and fixing SP blanking plate in the existing MCB DB complete as required

Supply, Installation, Testing and Commissioning of LED 4ft Batten IP40 luminaire of Robust anodized aluminum housing and high transitivity diffuser (Diffuser-Non yellowing type). The luminaire should have a LEDs with colour consistency SDCM ≤ 5, CRI ≥ 80 and CCT of 6500K. Luminaire shall be designed to emit at least 4000 nominal lumens at a system efficacy of at least 140 lumen/watt. Power consumption should not be more than 28W delivering minimum of 4000 lumens. The electronic driver used shall have a power factor ≥0.9 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤5%, Internal surge protection should be minimum 3.5KV. Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of maximum 10W recessed mounted High quality polycarbonate diffuser and PDC Al housing recessed design 125 mm Cutout for visual comfort Downlighter delivering >1000 Lumen, 5700K CRI>80, THD <10%, Input voltage Range 140-270 VAC. Replacable driver Luminaire driver both BIS Complient and having CRS ( R No ) L70B50 @ 50K Hrs, Power factor>0.95, IP20 protection, operating temperature range from 0 to 45 deg C, internal surge protection of 2.5kV. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of recessed mounted 2X2 LED Luminaire with CRCA housing and PS Diffuser. Luminaire should be available in minimum 3600 lumens having maximum system wattage of 30W with system efficacy of minimum 120lm/W. Color temperature of 6500K, SDCM<5 and CRI>80. The luminaire shall meet IP20 rating. The luminaire housing should made of powder coated CRCA with high efficiency PS Diffuser and having surge protection up to 3.5kV inbuilt in the driver. The driver must have operating voltage range from 140-240VAC with THD<10%, PF>0.95. Luminaire should have Class B serviceability. Life L70 @ 50000 hours at 45 deg C. LM79 and LM80 reports must be submitted from a NABL accredited laboratory, Luminaire and Driver must have BIS certificate and same must be submitted for records.Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of maximum 10W recessed mounted adjustable (Horizontal : ~+/30⁰) deep recessed COB based and PDC Al housing for visual comfort Downlighter delivering 1000 Lumen, 6500K CRI>80, THD <10%,Beam angle of 36°, Input voltage Range 140-270 VAC , EMI EMC Complient (as per CISPR 15). Replacable driver Luminaire driver both BIS Complient and having CRS ( R No ) L70B50 @ 30K Hrs, Power factor>0.9, IP20 protection, operating temperature range from 0 to 45 deg C, internal surge protection of 4kV. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of integral driver surface/ suspended luminaire with a system lumen output of minimum 1500 lumens and a minimum system efficacy of 100 lm/W with beam angle of 24 deg. The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature of 3000K and CRI > 80 (for 3000K). The luminaire shall meet IP65 rating and IK08 with PF >0.95. The luminaire shall have surge protection of 4kV in built in the driver, with operating voltage range of 140 - 280 Vac, 50Hz with THD< 5%; High voltage cut off at 325V with 440V phase to phase protection for 8 hours with auto restart feature. The luminaire should be made up of pressure die cast housing. The total power consumption should not exceed 15W (including driver). BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory. Luminaire and driver must be of same make. Datasheet of the luminaire, LM79 report, LM80 report, BIS certificate of the luminaire from NABL laboratory should be submitted during bid submission.

Supply, Installation, Testing and Commissioning of maximum 18W surface mounted High quality polycarbonate diffuser and PDC Al housing and PC diffuser for visual comfort Downlighter delivering >2000 Lumen, 6500K CRI>80, THD <10%,, Input voltage Range 140-270 VAC , EMI EMC Complient (as per CISPR 15). Replacable driver Luminaire driver both BIS Complient and having CRS ( R No ) L70B50 @ 50K Hrs, Power factor>0.95, IP20 protection, operating temperature range from 0 to 45 deg C, internal surge protection of 2.5kV. Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of 4' LED linear recessed LED with wattage 26W and System Efficacy & System lumens of 100 lm/W, 2600 lm respectively. The type of LED shall be SMD type mounted on MCPCB which is mechanically fixed (no glue pasting) with CCT of 4000K/5700K/6500K and CRI > 80. The housing material shall be extruded aluminium, PC diffuser. The life of LED shall be 50000 hours at L70. The LED shall be of SDCM < 5. The IP rating of the luminaire shall be IP 20. The ambient temperature shall be 0-45deg C. The lumianire optical element shall be UV protected polycarbonate. The lumianaire shall be operable from 140 - 270V AC with PF > 0.5 and THD < 10%. The driver shall be encapsulated type and placed within the luminaire. The driver shall be with in-built surge protection of 3.5kV. Drivers shall be flicker free and complies to IEEE P1789 standard; ripple < 5%. The effieciency of driver shall be > 90%. The luminaire shall be BIS approved and carry “R” number. Dimensions shall be of width - 50mm. Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of 4' LED linear suspended standalone/continuous LED with wattage 21W and System Efficacy & System lumens of 120 lm / W, 2500 lm respectively. The type of LED shall be SMD type mounted on MCPCB which is mechanically fixed (no glue pasting) with CCT of 4000K/5700K/6500K and CRI > 80. The housing material shall be extruded aluminium, PC diffuser. The life of LED shall be 50000 hours at L70. The LED shall be of SDCM < 5. The IP rating of the luminaire shall be IP 20. The ambient temperature shall be 0-45deg C. The lumianire optical element shall be UV protected polycarbonate. The lumianaire shall be operable from 140 - 270V AC with PF > 0.5 and THD < 10%. The driver shall be encapsulated type and placed within the luminaire. The driver shall be with in-built surge protection of 3.5kV. Drivers shall be flicker free and complies to IEEE P1789 standard; ripple < 5%. The effieciency of driver shall be > 90%. The luminaire shall be BIS approved and carry “R” number. Dimensions shall be of width - 50mm. Manufacturer shall have inhouse lab approved by NABL or Ministry of Science of Govt of India. LM79 and LM80 reports must be submitted from a NABL accredited laboratory. BIS certificate for driver as well as the luminaire must be submitted for records. Driver and luminaire shall be of same make.

Supply, Installation, Testing and Commissioning of exterior-rated LED floodlight in rectangular form factor having maximum wattage of 70W. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L70 at 35°C. Luminaire luminous flux of minimum 8500 Lm. Luminaire Housing - Pressure die-cast housing, with clear tempered glass, CCT 5700K, CRI>70, White SDCM<5. The luminaire should provided with Electrical safety class I, IP66, IK07, Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory. Luminaire and driver must be of same make. Datasheet of the luminaire, photometry file of the luminaire, LM79 report, LM80 report, BIS certificate of the luminaire from NABL laboratory should be submitted during bid submission.

Supply, Installation, testing and commissioning of 10W LED MIRROR LIGHT

Supply and erecting of 48 inch (1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. a) Cat A

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. Rate shall include bends, reducers, tees etc 100mm width x 50mm depth

150mm width x 50mm depth

200mm width x 50mm depth

300mm width x 50mm depth

Supplying and Installing following size perforated type 14 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 450mm width x 50mm depth

600mm width x 50mm depth

Supplying and Installing following size perforated type , M.S.cable tray cross of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. 100mm width x 50mm depth (16 SWG)

150mm width x 50mm depth (16 SWG)

200mm width x 50mm depth (16 SWG)

300mm width x 50mm depth (16 SWG)

450mm width x 50mm depth (14 SWG)

600mm width x 50mm depth (14 SWG)

SITC of UPS system comprising of 1 Nos. 15kVA ( 3 Phase input & 3 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 90 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications. 15 kVA ( 3 Phase input & 3 Phase output) with 90 min backup

SITC of UPS system comprising of 1 Nos. 5kVA ( 1 Phase input & 1 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 90 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications.

SITC of CAT 6A UTP LSZH Cable, 23 AWG solid copper conductors in accordance to TIA/EIA 568 C.2 (Category 6a) & ISO/IEC 11801 2nd ed(Class Ea), UL Approved, tested @500 Mhz, with HDPE insulation of individual conductor and over all Dia of 7.2 mm for Connectivity of Hub room to End Point. Grey Color

SITC of CAT 6A UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimum 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, & Wi-Fi at user end.

SITC of loaded 24 port CAT 6A UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6A cable termination at rack end.

SITC of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.

SITC of CAT 6A UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.

SITC of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.

Supply & Installation of 42 U floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, minimum PoE budget of 350W, with 2x 10G SFP+ uplink ports. Should support for Stacking/VC with stacking bandwidth of maximum 40 Gbps as and when required. Should support min 2GB internal DRAM, 2GB internal Flash memory, 16K MAC address. Should have Static Routing , Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), Domain Name System (DNS) and IPv6 features from day 1 and should support OSPF, VRRP, OSPFv3 and PIM with 1 year support.

Supply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : Customer Flow staistics, Cross COunt, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , In built IR LED , IR Distance upto 45 meters , IP 66 ,IK10,POE.Audio -1 input/1 output.

Supply, installation, testing and commissioning of Indoor WDR IR IP Dome Camera, White, with 2.7–13.5 mm motorized lens, PoE support, -Image Sensor: 1/2.8" 5MP progressive scan CMOS -Lens: 2.7–13.5 mm motorized varifocal lens, F1.4–F2.8 -Field of View: 100° (wide) to 30° (telephoto) horizontal -Resolution: Main Stream: 2560×1920 (1–25/30 fps), 1920×1080 (1–50/60 fps) -Wide Dynamic Range (WDR): Up to 120 dB -Low Light Sensitivity: 0.04 lux (color), 0 lux (B/W with IR) -Infrared Illumination: Built-in IR LEDs, up to 30 to 50 meters (98.4 ft) -True Day/Night (TDN): Auto-switching between color and monochrome modes -Compression Formats: H.265, H.264, MJPEG -Audio Support: Two-way audio (optional)

Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS ,2.7 mm to 13.5 mm motorized varifocal lens , Quad stream with each stream support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+/MJPEG .SD card support up to 256Gb, Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : Customer Flow staisticsCross Count, Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , IR Distance upto 45 meters , IP 66 , POE. Audio -1 input/1 output

Supply, installation, testing and commissioning of 5 MP PTZ camera , UL,CE,FCC,BIS Certified,OEM defined MAC address , ONVIF profile S,G & Q , Quad stream, 4.25-141.9mm focal length , 33 X Optical Zoom , 12 X digital Zoom ,Frame rate : 25/30 fps ,Shutter Speed : 1/5 ~ 1/100,000s , Inbuilt IR , IR distance upto 200 mtr , 2D / 3D noise reduction ,120 dB WDR , 360 deg endess pan , tilt -10 to 90 deg , auto flip support ,255 presets , Min. 32 preset add in each tour, Auto pan, Edge analytics : Pedestrian Intrusion Detection, Line cross Detection, Stationaary Object Detection, Vehicle Detection, face Detection, Sound Detection, Auto Tracking, Tempering detection, Defog, SD Card supportup to 128GB , Two Way, Auto white balance, Auto iris , Alarm : 1 IN , 1 Out ,IK 10, IP 67 weather proof , Power : POE+ /DC12V.

Supply, installation, testing and commissioning of 64 channel NVR , ONVIF compliant , recording bandwidth 640 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ45 ethernet , iOS smartphone support , 8 HDD support , each HDD slot support upto 6 TB HDD , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse .Edge analytics of poposed cameras must be integrated with NVR . Artificial Intelligence Support having face recognition with compatible deep learning supported cameras, AI-Face registered quantity upto 10,000 ,A.I maximum captured quantity 200,000. UL,CE,FCC certified.

Supply, Installation, Testing & Commissioning of 6TB Surviellance Hard Disk.

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, minimum PoE budget of 350W, with 2x 10G SFP+ uplink ports. Should support for Stacking/VC with stacking bandwidth of maximum 40 Gbps as and when required. Should support min 2GB internal DRAM, 2GB internal Flash memory, 16K MAC address. Should have Static Routing , Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), Domain Name System (DNS) and IPv6 features from day 1 and should support OSPF, VRRP, OSPFv3 and PIM.

Supply, Installation, Testing & Commissioning of Rack 26U

Supply, Installation, Testing and Commissioning of Full HD 55" Smart LED Professional Display Panel.

Supply of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supply, Installation, Testing and Commissioning of Cat 6 Armoured Cable For External Camera

Supply, installation, connecting, testing and commissioning of addressable photoelectric type MULTI Detectors with mounting base, blinking LED etc. complete as required. Below False Ceiling

Above False Ceiling

Supply , Installation , Testing and Commissioning of Response Indicator (RI) High visibility LED, Wide viewing angle for increased visibility, Discreet design for incorporation in to any décor. RI should be of same make as detectors & devices.

Supply of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches UL268, 7th Edition & FM Approved.

Supply, installation, connecting, testing and commissioning of Addressable Manual Call Box in ABS plastic as required complete.It shall be Pull handle type with cover.

Supply, installation, connecting, testing and commissioning of addressable Control module for Hooter.

Supply, installing, testing and commissioning of Addressable Relay Module for AHU, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs

Supply, installation, connecting, testing and commissioning of addressable Monitor module for flow switch.

Supply, installation, connecting, testing and commissioning of Addressable Hooters cum strobe min. 80 db output and 110 candelas complete with modules. The strobes shall be synchronised for better evacuation.

Supplying, installation, testing & commissioning of Self illumination EXIT Signages 4" x 12 " size i/c fixing arrangement complete as required.

Supply, installation, connecting, testing and commissioning of addressable fault Isolator.

Supply of Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be complete with 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. Designed to meet UL864, 10th Edition & FM approved. 02 Loop

Supply of Addressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center. UL Listed.

Supply of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supply of 2 C X 1.5 Sq mm multi stranded twisted shielded FRLS Copper cable.

SITC of 6W Ceiling Speaker with max SPL1M/1W 96dB . Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W Ceiling Mounted Speakers

Box Type Ceiling

SITC of 8 zone IP based, digital Voice Alarm controller expandable upto 128 zones. The voice alarm controller should be able to connect directly over Ethernet. It should have functions like the audio playing, zone control, fault monitoring, log recording, volume control and amplifier switchover. The Voice alarm controller should also have the following functions: . 255 Priorities . Time schedule broadcasts . Its own PTT microphone . Capable of amplifier redundancy . 8 trigger inputs/outputs

SITC of 1X500W Class-D Amplifier with 2 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection. 500 Watts

Supplying and Laying of 2 C X 1.5 Sq mm multi stranded twisted shielded FRLS Copper cable.

Supplying and installing armoured single mode optical fibre cable with 6 fiber, core dia 50/125μm (OS1/OS2) 10/40 GBPS speed in provided underground HDPE pipe complete. FOR Lan

Design Supply installation testing and commissioning of high-quality integrated LED Sports Flood Light with a minimum system lumen of 60K Lm and system wattage not exceeding 200W (+/-5%) with a nominal efficiency >150 lumen/watt for 60 deg beam angle . CCT :5700K (tolerances on CCT: +/- as per ANSI C78:377A) CRI: >70 . LED Make : Cree/Nichia/Lumileds only , LED Chip driving wattage : >2W<=5W , L-70 Life: minimum 50000 Burning Hours The housing should be of High Grade ADC 12 PDC Al alloy housing with Passive Cooling heat transfer technique , offering a totally silent, robust, heat transfer with seperate driver & optical compartmnet for thermal isolation , powder coated with corrosion resistance Powder using Nano Technology to withstand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. . The Luminaire driver should be made of Extruded Aluminium housing with IP67 protection for better thermal management and durability and should have an internal surge protection of 6kv with additional External SPD of 20kV/10KA duly fixed inside the luminaire, Drive should be with PF >0.95, THD<10% and output ripple current shoould be less than 2% at Io max. The luminaire should be of Class B Serviceability. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire.

Design Supply installation testing and commissioning of Indoor Lighting Panel with necessary cables from Panel to Each light fixture mounted on catwalk , including necessary termination

Supply of of high-quality integrated LED Sports Flood Light with a minimum system lumen of 60K Lm and system wattage not exceeding 200W (+/-5%) with a nominal efficiency >150 lumen/watt for 60 deg beam angle . CCT :5700K (tolerances on CCT: +/- as per ANSI C78:377A) CRI: >70 . LED Make : Cree/Nichia/Lumileds only , LED Chip driving wattage : >2W<=5W , L-70 Life: minimum 50000 Burning Hours The housing should be of High Grade ADC 12 PDC Al alloy housing with Passive Cooling heat transfer technique , offering a totally silent, robust, heat transfer with seperate driver & optical compartmnet for thermal isolation , powder coated with corrosion resistance Powder using Nano Technology to withstand extreme environments. It should have corrosion resistant powder coating to pass NSS of 500 Hrs. Product should be suitable for continuous operation (10-12 Hrs. per day). The Ingress protection should be minimum IP 66 with an IK rating of 08. . The Luminaire driver should be made of Extruded Aluminium housing with IP67 protection for better thermal management and durability and should have an internal surge protection of 6kv with additional External SPD of 20kV/10KA duly fixed inside the luminaire, Drive should be with PF >0.95, THD<10% and output ripple current shoould be less than 2% at Io max. The luminaire should be of Class B Serviceability. The luminaire should be capable of withstanding voltage stress of 440V for 8 Hrs., should have an auto shutdown @ 325V and have an auto recovery feature. The Drivers should be a potted driver not a printed circuit board without casing, mounted inside the luminaire.

Design Supply installation testing and commissioning of Indoor Lighting Panel with necessary cables from Panel to Each light fixture mounted on catwalk , including necessary termination.

Supplying split type variable speed Inverter technology room Air conditioning unit 1 TR capacity 3 star suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall type,with Refrigerants R410 A/R32 and copper condenser at position including 3 mtr copper piping, 3 mtr flexible 2.5 Sq.mm copper cable for indoor to outdoor connection, 3 mtr Drain pipe with reqired nitrile rubber / foam tube type sleeves etc complete job as required by Engineer Incharge

Supplying split type variable speed Inverter technology room Air conditioning unit 1.5 TR capacity 3 star suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall type,with Refrigerants R410 A/R32 and copper condenser at position including 3 mtr copper piping, 3 mtr flexible 2.5 Sq.mm copper cable for indoor to outdoor connection, 3 mtr Drain pipe with reqired nitrile rubber / foam tube type sleeves etc complete job as required by Engineer Incharge.

Supplying split type variable speed Inverter technology room Air conditioning unit 2 TR capacity 3 star suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall type,with Refrigerants R410 A/R32 and copper condenser at position including 3 mtr copper piping, 3 mtr flexible 2.5 Sq.mm copper cable for indoor to outdoor connection, 3 mtr Drain pipe with reqired nitrile rubber / foam tube type sleeves etc complete job as required by Engineer Incharge

BOQ HIGH SIDE VRV EQUIPMENTS . Voltas, Blue Star, Carrier, Toshiba SUPPLY OF VRV -VRF UNITS Supply of following type VRF / VRV units with Inverter Technology compressor The units should be complete with indoor unit, condensing unit, controls, microprocessor control panel, internal wiring, refrigerant piping, etc. Cassette units shall be complete with drain pump suitable to meet site requirements. To have provision for potential free contact -to get signal from BMS in case of fire -so that AC can get shut off. All accessories for installation / commissioning should be part of the package 50 HP Ground & First Floor

Refnets for VRV System (To be supplied by unit manufacturer inddor and out door both refnet )

Copper Piping duly insulated with required 13 & 19mm nitrile insulation for suction & liquid Line

Indoor to Outdoor unit Control cabling with sheathed Cu cable 2C x 1.5 Sq.mm.- Conduit

Drain piping for Indoor units - Hard pvc of suitable size, with 12 mm armaflex insulation 25mm dia

32mm dia

40mm dia

50mm dia

Refreigerent Gas

Supply, fabrication and installation of MS base frame for outdoor units complete with epoxy painting, vibration isolation pads, supports, hangers, railing, brackets etc. For construction Construction as approved by Architect/ Consultant. Apply 2 coats of epoxy primer 2 coats of epoxy paint and finish painting as approved by Architect. Stand to be made as per site conditions. 50 HP

24G -Ducting -Fabricated as per IS standards with angle Iron Flanges. (Supply and Installation of GI sheet metal duct, supports, adjustable volume control Splitter dampers, guide vanes with necessary flexible connections, etc.) 24G -Ducting

22G - Ducting

20G - Ducting

Alternate rates for Pre insulated Ducting- Vendor PAL , ALP , Endura Gold ( Owens Corning ) with 20mm / 21 mm / 25 mm thickness with Pre Insulated Al Polyurethane / Closed cell Expanded Polyurethane Rigid Board / Fiberglass -- Aluminium backed both int Mode of measurement will be centre to centre 20mm

24G Flat Oval Ducting – (Supply and Installation of GI sheet metal duct, supports, adjustable volume control splitter dampers, guide vanes with necessary flexible connections etc.)

22G Flat Oval Ducting – (Supply and Installation of GI sheet metal duct, supports, adjustable volume control splitter dampers, guide vanes with necessary flexible connections etc.)

Enamel painting as per IS standards

Supply Air Grilles with Al. VCD - Linear Fixed Bar Grilles, Horizontal Fixed Bars, Normal Blade (5 mm nominal thickness) Grille height 16 mm, blade pitch 12.5 mm, with opposed Blade aluminium extruded construction VCD Black Anodized Supply Air Grilles - with damper 150 mm

Curved Grille with damper 150 mm

Supply Air Diffusers with Al. VCD - Multicone Ceiling Rectangular Diffusers with removable cores, core styles 1/2/3 way with opposed Blade aluminium extruded construction VCD Black Anodized Supply Air Diffusers

Supply Air Round Diffuser

Return Air Grilles without Al. VCD - Linear Fixed Bar Grilles, Horizontal Fixed with removable cores, core styles 1/2/3 way with opposed Blade aluminium Bars, Normal Blade (5 mm nominal thickness) Grille height 16 mm, blade pitch 12.5 mm. Return Air Grilles - 150 mm

Return Air Grilles - 100 mm

Return Air Diffusers without Al. VCD - Multicone Ceiling Rectangular Diffusers with removable cores, core styles 1/2/3 way. Return Air Diffusers

Return Air Round Diffuser

SUPPLY AIR SQUARE DIFFUSERS WITH VCD ( PANEL SIZE 600 X 600 , TO SUIT AMSTRONG GRID CEILING Neck size 12" x 12" .

Neck size 15" x 15" .

Neck size 18" x 18" .

Slot Diffusers with Vane Air Pattern Controllers including mitered corners etc. MD 75 MD 75 - 3 slots (150 mm wide)

MD 75 - 2 slots (100 mm wide)

Disc Valve- to regulate flow from 20 cfm to 100 cfm

Fire Damper

Actuator for Fire damper

Control cabling for above

Supply , installation testing & Commissioning of Insulated Plenum Boxes.

Grille Damper - Opposed Blade Aluminium Extruded Construction Black Anodized. Grille Damper - Opposed Blade Aluminium

GSS VCD for Ducts - 20 G GI blade, 100 mm wide, 18G GI frame 120 mm wide chrome plated spindles, self lubricating bushes, blade linkage, fully enclosed, handle operation with status indicator. GSS VCD for Ducts -

Canvass Connection For AHU Unit/TFA UNIT Thermal insulation of Ducts with 25 mm thick. factory laminated fibreglass (24 Kg/Cu Mtr) with Al. tape at joints. Duct insulation with 25mm thick Twiga 200 Al. backed fiberglass insulation fixed using shalikote primer, hot bitumen, Chicken wire mesh, PVC straps etc. Thermal insulation of Ducts with 50 mm thick. factory laminated fibreglass (24 Kg/Cu Mtr) with Al. tape at joints. Duct insulation with 50mm thick Twiga 200 Al. backed fiberglass insulation fixed using shalikote primer, hot bitumen, Chicken wire mesh, PVC straps etc. Acoustic insulation of Ducts with 25 mm thk. fibreglass (48 Kg/Cu Mtr) and 30 G Al perforated sheet. Acoustic lining of duct work with 25 mm thick fiberglass stick using shalikote primer hot bitumen and mechanically fastened,covered with RP tissue and 30G aluminum perforated sheet as per specs. Acoustic lining shall be rigid board. Acoustic insulation of Ducts with 12 mm thk. fibreglass (48 Kg/Cu Mtr) and 30 G Al perforated sheet. Acoustic lining of duct work with 12 mm thick fiberglass stick using shalikote primer hot bitumen and mechanically fastened,covered with RP tissue and 30G aluminum perforated sheet as per specs. Acoustic lining shall be rigid board. Nitrile rubber Insulation - 6 mm Accoustic with Open Cell Nitrile rubber Insulation - 6 mm Thermal with closed Cell Duct insulation with 6 mm thick Class O Nirile Rubber Insulation. Insulation to be fixed using adhesive as per manufacturers recommendation. Seal all joints using self adhesive AL backed Nitrile rubber tape . Adhesive used shall meet Leed requirement

Nitrile rubber Insulation - 9 mm - Accoustic with Open Cell

Nitrile rubber Insulation - 9 mm - Thermal with Closed Cell

Duct insulation with 13 mm thick Class O Nirile Rubber Insulation. Insulation to be fixed using adhesive as per manufacturers recommendation. Seal all joints using self adhesive AL backed Nitrile rubber tape . Adhesive used shall meet Leed requirement

Accoustic Insulation of Ducted Indoor unit with 19 mm Open cell Nitrile Insulation - if required to dampen Noise level

13 mm crosslink XLP with Aluminium Foil. To have Fire Resistant feature.

All indoor unit outlet collars shall be insulated with 6mm thick heatlon/profeel fixed with adhesive as per manufacturers specs.

(A) Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E )Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 60 m Head

(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Terrace Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (D) M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (E )Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 lpm at 35 m Head (1W+1SB)

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 25 mm dia.

32 mm dia.

40 mm dia.

50mm dia.

65 mm dia.

80 mm dia.

100 mm dia.

150 mm dia.

200 mm dia (wall thickness 6.3 mm)

250 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm dia.

100mm dia.

150mm dia.

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required : 65mm dia.

80mm dia.

150mm dia.

250mm dia.

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 65 mm dia.

150 mm dia.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 250 mm dia.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way-150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Upright Sprinkler

Horizontal side wall sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100 mm dia

150 mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150 mm dia.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000mm

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing angle iron (40mmx40mmx5mm) door frame and MS sheet (6mm thick) cum glass shutter of size 2.1mtrx0.9mtr(N.S.) with 25mmx25mmx3mm angle frame all around and stiffened in between i/c hinges, handle, locking arrangement, painting with approved synthetic enamel paint i/c sign writing on glass at internal hydrant including providing & fixing S.S. sheet 2mm thick on remaining portion above door to close opening i/c painting etc. as required. Glass shall be 6 mm thick.

Providing & fixing of MS fire Hose cabinet outdoor type of size 0.90 Mx 0.60 Mx 0.50 M made of 6mm thick MS sheet with 6mm thick glazed glass doors i/c necessary locking arrangement suitable to accomodate 2nos 15m long hoses, one no branch pipe, etc. and mounted on 400 mm height agle . The cabinet shall be painted with red colour shade No. 536 of IS: 5 externally & white internally complete in all respects for internal hydrant and as per enclosed specification.

Providing & fixing of 25mm dia. gunmetal air release valve with all fittings and forged ball valve on header complete as required and as per enclosed specification.

Providing and fixing following size Pressure gauge (0-15 Kg/Cm2) complete with shut off valve duly calibrated before installation complete as required & as per enclosed specification. 150mm dia.

Providing, fixing, testing & commissioning of MS air vessel tank of pump room fabricated from 6mm thick MS plate, 400 mm in diameter and 2.0 m in height with dished ends fabricated from 8mm thick MS plate with Air release valve with stop cock, flanged inlet connection and drain arrangement with 25mm dia valve, pressure gauge with gun metal stop cock complete with all accessories as required and conforming to IS 4736-1968. Recommended dia. : 450 mm Height of shell : 2000mm Working pressure : 7 Kg/Sq.cm Test Pressure : 10 Kg/Sq.cm

Providing and fixing inspectors test assembly complete with test valve, sight glass sectional drain valve, union with corrosion resistant orifice all complete strictly as per drawing.

Supply, installation, testing and commissioning ISI marked (IS:15683) Fire Extinguisher, Carbon-di-oxide type capacity 4.5 Kg. Flat base including valve, discharge hose of not less than 10 mm dia, 1M long and complete in all respects including initial fill with CO2 gas conforming to IS:307-1966 and walll suspension braket as required as per specifications.

Supply, installation, testing and commissioning of 6kg ABC (Powder Type) Fire Extinguisher. Mild Steel Cylinders ISI marked fitted with pressure indicating gauge, internal tube, squeeze lever type valve fully charged with ABC 90 powder (Mono Ammonium Phosphate) pressured by Nitrogen complete in all respects including wall suspension bracket and conforming to IS:15683 as required as per specifications.

Providing and fixing stainless steel standard fireman's axe with heavy insulated rubber handle tested to 20000 volts as per IS : 926 complete.

Providing and fixing fire brigade suction hose coupling (draw out connection) with nut for female coupling as per IS-902 complete with 150mm dia. Suction pipe and foot valve (to be connected to static tank) complete as required and as per enclosed specification.

Please Enable Macros to View BoQ information