Construction of Production well at Zethyar 2nd Rajbahawan vicinity and providing, installation testing and commissioning of Electro-Mechanical equipment with allied works for harnessing of the well. (Construction of Production well already completed)

Amount

Supply, Installation, Testing and Commissioning of submersible pumping unit conforming to IS 8034;2002 specifications of below mentioned parameters to be lowered inside well casing having inside diameter of 8 inches. Pump: Type: Submersible [Multistage, Bowl Type] Speed: 2900 RPM Discharge: 4500 GPH Dynamic Head; 130 Mtrs Valve body CF8 Stage Casing SS 304 Pump overall efficiency not less than 50% MOTOR /PRIME MOVER: Type: Submersible Speed: 2900 RPM Phases: 3 - Phase AC supply 50 Hz Capacity: Suitable capacity, as recommended by Pump Manufacturer Motor efficiency Not less than 80% Preferable makes: KSB, Kirloskar, CRI ------------As per Serial No. 1 of Annexure"D" of NIT

Providing and fitting of ISI marked flat/round 3-core 16 Sq. mm PVC insulated & PVC Sheathed water proof Submersible Copper Cable (havells, polycab and L&T) for above pump/motor unit conforming to IS:694. The job includes providing/Fitting of Conduit/Thimbles &Tapping’s etc. as per site requirement.

P/I/T/C of the min. 850VA inverter assembly of reputed brands with sine wave technology and having LCD display to be fitted at operators’ quarter along with necessary cabling, Terminals etc. required as per site. The job includes P/F of lighting (03) No points in 1.5sqmm PVC insulated copper wire, as per requirement, through PVC channel/conduit. The job includes P/F of 5AMP ON/OFF switches& two No pin Sockets on Bakelite sheet along with 9/11W LEDs with necessary fixtures. The job also includes providing/Fitting of the 12Volt, 150Ah chargeable battery of reputed brand with minimum 5 years of warranty with trolley to be fitted / connected with inverter.

Providing, Installation, Testing and Commissioning (PITC) of 100 amps LT Modular Control Panel along with other allied Electrical Accessories, to be carried out for HARNESSING of New Production Well at Lift WSS “ZETHYAR 2ND (New Well)’ in Rajbhawan vicinity by way of: Design, Manufacture, Providing, Fitting, Testing & Commissioning of Direct Online Motor Starter Panel fabricated out of 2 mm CRCA Sheets Modular, compartmentalized, Free Standing, Floor Mounting, Front hinged doors for indoor use, removable bottom gland plates for incoming cables, dust and vermin proof (IP: 42 protection) with TPN Copper Buses, complete with connection, internal wiring, name plates, painting, vents etc. generally as per details furnished below:------------As per Serial No. 4 of Annexure"D" of NIT

P/I/T/Commissioning of 50 kVA voltage stabilizer of following specifications: a) Type: Manually operated oil cooled b) Capacity: 50 kVA .c) No of phases: 3 No of phases, 50 HZ frequency) Operating conditions: 1. Input 280 volts ±10% (Line to Line) to 415 volts ±5% (Line to Line) on 3 phase AC supply 2. Output: 415 volts ±5% (Line to Line) 3 phase AC supply) Terminals: Three No incoming and three no outgoing terminals along with one No Neutral Terminal fabricated out of brass studs, nuts and washers fitted on Bakelite sheet with dully drilled holes. The distance between the terminals should be sufficient to accommodate the suitable size cable terminals. ------------As per Serial No. 5 of Annexure"D" of NIT

P/F of 3.5 core 35 sq. mm PVC/XLPE ARMOURED cables with ALUMINIUM conductor 650/1100 V. grade confirming to IS: 7098 (Part-1) 1988 XLPE armored Aluminum of reputed brands ( havells, polycab and L&T) For service line from HT Substation to the panel. The job includes Thimbling etc.

P/F of the 11KVA Termination end kit suitable for 35 Sq.mm XLPE Armored Al Cable

P/F of 16 Sq. mm PVC insulated industrial flexible copper cable 1100V, unsheathed, conforming to IS; 694, bright annealed copper conductor for interconnections. of reputed brands ( havells, polycab and L&T), length may vary as per site requirement

Fabrication/Fitting/I/T/Commissioning of 2 Ton Capacity MS Gantry along with the CP Block by way of:

Cutting to size, shifting and Fitting of vertical posts 02 No. ISMC 150 welded back-to-back (Approx. 5M long available at site) Fitting of One no. horizontal beam fabricated out of ISMB-150 (Approx. 3.9 M long available at site) = 4.57 rmt @ 14.9 kgs/rmt

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete by way of: P/F of Bearing plates stiffeners, braces, fabricated out of 10mm thick M.S plate. Average size of plate is (300x300) mm and that of stiffeners is (150x150) mm triangular shape welded to bearing plates, vertical posts and beam 6 plates @ 7.02 kgs/plate= 42.12Kg Stiffeners-16 nos x 880 gms= 14.10Kg

Nuts and bolts of assorted size

P/Laying of CC block for embedding foundation bolts in (1:2:4) mix of (1 cement: 2 coarse sands: 4 graded stone aggregate 20 mm nominal size) 0.28 Cum for each block. The job includes arranging of skilled labour, form work, earth work excavation and cost of material complete for block. Size-2’x2’x2 ½’

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete by way of : P/F of ladder fabricated out of ISA (40x40x5) mm horizontal pieces as steps each 2.00 feet wide welded on one side to the vertical post of gantry arrangement and to ISA (50x50x5) mm vertical member on the other side up to top. Includes all leads, lifts and carriage up to site of work. ISA 40x40x5 2’x8=16’=4.88rmt@3kg/m=14.64kgs ISA 50x50x5 1¯x14’[email protected]/m=16.22kgs

Providing, Installation, testing and commissioning of 2 Ton capacity motorized Chain Hoist complete with suitable heavy duty cast steel rope / chain link guide operating chain 15m long. Technical Specification; a) Product: Electric chain Hoist b) Capacity: 2 Ton c) Standard Lift: not less than 5.5 M d) Span: 3.6M e) Class of Duty: Class 3rd. Medium duty IS-3177, 807 f) Operation: Pendent g) Speed MPM Main Hoist: 3.0 MPM h) Motors (HP) Main Hoist: 1.5 hp/ or as suitable, Crane duty i) Rope/Chain Dia.(mm): 10mmor as per safe design requirement. j) No of Fall: 2 k) Wheel: Double Flange Forge mounted on roller bearing for lift l) Limit Switches: Provided in all motion (RLS/ LLS Type) m) Hook: Single Shank Type confirm to IS-3815 n) Cables: PVC Cu ISI Mark o) Panels: Conforming to approved IS Std p) Control Voltage: 380V A C +/- 10%

Manufacturing, providing and fitting of suitable size (1.60mx1.60m) canopy over the Electric Chain Hoist structure to prevent the motor & allied parts from rain/snow using 40x40x6mm MS angle and coloured GS sheets 0.5mm thick along with J hooks & fasteners (as per site requirement) with carriage ISA;45x45x5=48kg GS Sheets, 2.56SQM

Providing/fitting of ‘B’ Class 65 mm Dia. GI pipe as per IS-1239 part-1/IS-3589 of length 10 feet each to be used as Column pipe & to be fitted inside the well casing. The Job includes P/F BS-10 T/E 2 No MS flanges 65 mm dia., 14 mm thick to be welded to extreme ends of the pipe. Providing/Fitting of 1.5" x 1.5" 3 no’s right angled triangular MS 10mm thick stiffeners at each end of column pipe of 10’ feet length for imparting strength by way of cutting the stiffeners out of 10mm thick plate/Flat & welding and Fabrication work as per site requirement. The Job includes cutting of groove through the flanges for accommodating the Submersible cable. The job also includes P/F of the Nuts/Bolts & washers of assorted size with carriage.

Providing and fitting of 65 MM Dia. flanged PN-16, D.I non-return-valve conforming to the GGG-40. The job also includes P/F of the T/H Flanges along with Nuts/Bolts & washers with carriage. Note: Supplier shall have to manage to produce online test certificate from the “OEM” of the Equipment to the Department at the time of supply

Providing and fitting of 65 MM Dia. flanged PN-16, D.I Non-Rising Stem Gate valve conforming to the IS; 210 FG-200. The job includes P/F of the T/H Flanges along with Nuts/Bolts & washers with carriage Note: Supplier shall have to manage to produce online test certificate from the “OEM” of the Equipment to the Department at the time of supply

Fabrication/Fitting of the MS increaser 65mmx80mm dia. & 460mm long, fitted with two No MS Flanges of appropriate size to be welded on either end. The job includes P/F of washers/nuts/Bolts as per site requirement with carriage.

Providing and fitting of M.S clamp (comprising of 2 parts/No’s) 12mm thick,100mm wide & 20” long along the semicircle to be fitted using M.S fasteners for holding of 65 mm Dia. column pipes in hanging position at top, over Well casing of having 8 inches Dia with all carriage

Fabrication, Providing and fitting of washout system which includes: 80mm dia. C Class GI Pipe T joint 1 M x 2M welded 80mm dia. 12 mm thick MS flanges 3 Nos complete with nut and bolts, rubber insertions as per site requirement. The Job includes Providing & fitting of Angle Iron supports fabricated out of ISA (40x40x5) grouted in 1: 2:4 mix as per site requirement with all carriage complete.

Providing and laying of the 200 mm diameter, 5.4mm thick Mild Steel Pipe to be laid as Jacketing pipe for laying/fitting of the 80mm diameter rising main is to be laid through this 200mm diameter jacketing pipe, through which the pipe line will pass near the vulnerable areas/entrances so that repeated road cutting is avoided during the damages. The Job includes Earth cutting through Mechanical /manual means as per site requirement with all carriages and providing and laying and filling of 1:1.5:3 mix cement concrete over jacketing pipe line to make the cutting portion of macadam to make the road smooth / hurdle free.

Providing/fitting of ‘B’ Class 80 mm Nominal Dia. GI pipe as per IS-1239 part-1/IS-3589 of length 20 feet each to be used as Rising Main pipe from the delivery end/Tube Well Top up to the existing rising main. The Job includes P/F BS-10 (1962) T/E, 2 No, MS flanges 80 mm ND & 185mm overall diameter. 12 mm thick having four No holes to be welded by Electric Arc Welding in double layers to the extreme ends of the pipe. The job includes P/Fitting of the 5/8” size Nuts/bolts along with assorted size Rubber/Insertion washers. The pipe line is be laid underground after manual excavation / or as per site condition.

Providing, fitting of 80 mm ND, PN10, Ductile Iron double flanged, resilient seated Gate valve. Body and bonnet of ductile cast iron (GGG-40), wedge ductile Cast Iron (GGG-40) all around fully vulcanized EPDM rubber, Bonnet Bolts, Stem of Stainless Steel & Stem Nut of Brass (Approved for drinking water) and NBR seal. Gate /Sluice valve shall be compatible for buried application and shall be safe to install in both horizontal and vertical positions conforming to BS-5263. It shall have electrostatic epoxy coating according to CSK Guidelines inside and outside approved for drinking water, the valve shall be supplied along with hand wheel. The job includes providing and fitting of 02 No, MS T/H Flanges perfectly adaptable to the inbuilt flanges of the valve, which shall be fitted in the Rising Main with all carriage Note: Supplier shall have to manage to produce online test certificate from the “OEM” of the Equipment to the Department at the time of supply

Providing, fitting of 80 mm, PN10, Ductile Iron double flanged, Slanted seat non-Return valve (NRV). Body & disk/Flow Guide of ductile cast iron (GGG-40) with fully encapsulated vulcanized EPDM rubber (Approved for drinking water). Valve shall be compatible for buried application and shall be safe to install in both horizontal and vertical positions It shall have electrostatic epoxy coating inside and outside approved for drinking water. The job includes providing and fitting of 02 No. M.S T/H Flanges perfectly adaptable to the inbuilt flanges of the valve, which shall be fitted in the Rising Main. Cost on account of Nuts, bolts, gaskets, etc. required for the job is included in the scope of work with all carriage. Note: Supplier shall have to manage to produce online test certificate from the “OEM” of the Equipment to the Department at the time of supply

Providing, fitting, Installation, testing & commissioning of the DN 25, PN10 Automatic type, single chamber type Air Valve in compact design, resilient seated with body & Bonnet of ductile cast iron (GGG-40) stainless steel float, shut off Device & Ring & inner parts conforming to 1.4571/1.4541 with EPDM Sealing & inside, outside epoxy coated conforming to GSK Guidelines with all carriage.

Repairs / renovation to the existing 63 kVA sub-station by way of: -

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete by way of: Providing & replacement of ISMC 75 channel after dismantling the old one, length as per site requirement. including providing and fitting of necessary nuts/ bolts etc. wt 7.14kg/m, total length 3m. (3m*7.14= 21.42kg)

Dismantling the old Dropout system and providing and fitting of gang operated Dropout link set (11KV including nuts/ bolts etc.

Dismantling the old fuse set complete, providing and fitting of 11 kV fuse set including nuts/ bolts etc..

P/I of earthing system for substation, LT panel, and stabilizer comprising of company fabricated earthing electrode as per IS: 3043. The job includes Auguring of bore of required dia/depth for installation of electrode along with backfill compound mixed with soil and all other items required thereof for achieving the best result. The job includes connecting of electric gadgets through GI strip as per relevant standards. Safe earthing electrode size : 80 mm dia , Length 3000 mm Back fill compound : 30 kg

Supply, installation of 6 kg CO2 type fire extinguisher manufactured as per IS: 15683 of 2006 with IS mark and comply with DGMS (Approval). The co2 extinguisher should be suitable for class B & C fire and also for fire involving electrical equipment. The cylinder used for fire extinguisher shall be approved by petroleum and explosive safety organization (PESO) as per gas cylinder rules 2004 and as per IS: 7285 of 2004. The body should be made of seamless steel (manganese) confirming to IS: 7285 with IS mark and should be provided with squeeze grip nozzle and should be filled with co2 confirming to IS: 15222 of 2002 with certificate. The extinguisher shall be provided with manufactures test certificate and hydraulic test certificate by BIS from PESO.

Providing and fitting of prodigy LT meter of following specification complete with all fixtures required for fitting at site for above mentioned scheme. Type: E3L 100, 3-phase, 4-wire Measurements offered: KWh, KVARh, KVAh, KVA Voltage: 240 V (415 V) 50Hz, Lb:40 A, Imax= 200A Battery: Lithium (SECURE)

Miscellaneous items:

Insulation gloves (Class 2) from reputed brands conforming to IEC 60903, EN 60903 or equivalent standards. Make: Raychem, Honeywell,3M (Supplier shall have to manage to produce online test certificate

Dielectric boots (Class 2) from reputed brands, conforming to EN 20345, EN 50321 or equivalent standards Make: Honeywell, Novak, harvik(Supplier shall have to manage to produce online test certificate).

Electrical insulating mats as per IS 15652:2006-3.3kv 1no. 1*2 mtrs 1 no. 1*1 mtrs

Safety helmet for Men Industrial and construction helmet conforming to EN 397:2012, IS 2925 or equivalent standards.

Earthing tester, make: HTC model: CE8200

Clamp meter make: HTC model no. CM-2070FT, 1000A

HTC 6250 IN 5KV-200G Digital Insulation Tester, 3 in 1 Insulation Resistance, phase testing & Voltage testing

Detailed estimate for Providing, Installation, Fitting, Testing and Commissioning of 30KVA Water Cooled D.G Set at Water Supply Scheme Lift Station Zethyar 2nd (Harnessing of Newly Constructed Production Well) Diesel Engine (Prime Mover) Make :Cummins/ CATERPILLAR / VOLVO PENTA / KIRLOSKAR OIL ENGINES LIMITED Model: Corresponding to given requirements BHP at NTP: Above than the output rating of alternator as per standards. Speed: 1500 rpm Number of cylinders: Corresponding to Model. Aspiration: NA/TA/TC Cooling system: Water Cooled Method of starting: Self-excited, 12 Volt battery start ------------As per Serial No. 28 of Annexure''D" of NIT

Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in : 15.17.2 Channels, angles, tees and flats

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 meters lead.

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of 5.28.1 G.S. Sheet

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil

Providing and laying of Soling/boulder in bed hand packed up to 1’ thick including watering, dressing and ramming with all carriages, loading, unloading and staking etc complete

Centering and shuttering including strutting, propping etc and removal of form work for Retaining walls, return walls, walls (any thickness) including attached pilasters buttresses, plinth and string course fillets, kerbs and steps etc

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) ( 1’ BGL and 1 ’ AGL )

Providing and filling of boulders 1.5` from ground level and levelling thereof

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering All work up to plinth level 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size over whole plinth area

Providing and laying of 12mm thick Cement plaster (in fine sand) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 fine sand)to plinth above ground level and to the floor

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete (section ISA50x50x6mm and 65x65x6mm). The agency has to utilize departmental steel available at site. (The amount of which shall be deducted as mentioned in item No. 50)

Providing and fixing pre-coated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge The sheet shall be fixed using self-drilling /self-tapping screws of size (55x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required finished Dimensions:- finished quantity

Providing and fixing pre-coated galvanized steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120grams per sqm as per IS: 277, in 240 Mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self-drilling/ self-tapping screws complete: Ridges plain (500 - 600mm) Ridge finished

S/P/F of Operators quarter cum machine room of sandwich type puff panel with following specifications Thickness of PPGI / PPGL sheets : 0.5 mm (the sheets shall cover both sides of puff sheet ) Puff density : 40 kg / cum ( Approx ) Coatings : As per IS – 277 Total nominal coating : 25 microns Temperature resistance : 1500C Continuous service temperature : 85 0C The job includes all the charges on account of supply and fitting of necessary fixtures, fasteners, carriages, head loads, loading and unloading etc As per Drawing Dimensions:- finished quantity

Walls Thickness of puff : 60 mm

Ceiling Thickness of puff : 40 mm

Fabrication and fitting of doors, windows and ventilator cum space for exhaust fans out of colour coated Aluminum Complete in every respect ie P/F of Hinges, Handles, rollers with channels, AL drops’ tower bolts etc Doors : 1 No x 6’ x 2.5’ Doors :3 No x 7’ x 3’ ( 2 doors for DG Set room with proper locking arrangement and one for M/C/Op. room with proper locking arrangement) Windows : 3 No x 4’ x 4’( With mesh, glass, shutters/Sliders etc) Ventilator : 2 No. x 1’ x 1’ (space for Exhaust fan )

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fitting of bath fittings consisting of: 25 mm PPR pipes (length as per site requirement) complete with bib cocks and allied fittings for three points 35 ltr geyser with all fittings and pipes and electrical fittings 500 ltr triple layer PVC water storage tank to be fitted over washroom The job includes all the charges on account of support members of suitable size and length angle iron and MS flat 21’’ ceramic commode complete with cistern and allied fittings viz Type – B PVC sewage pipes complete with P trap, bends, collars, air pipe etc with stand for storage tank fabricated out of (ISA 50 x 50 x 6 mm) 4 No x 7’ = 28 rft 4 No x 3’ = 12 rft 4 No x 5’ = 20 rft Total 60 rft = 18 rmt @ 4.5 kg/m = 81 kgs (length of pipes may vary at the time of actual execution)

Electrification of Pump House by way of P/F of :- Lighting points in 1.0 sq mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit The job incl P/F of 5 Amp switch, angle / button holder, 5 W LED lamp with necessary fixtures – 04 jobs Lighting points, bulk head type in 1.0 sq. mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit The job incl P/F of 5 Amp switch, angle / button holder, 5 W LED lamp with necessary fixtures – 04 jobs Heating points in 2.5 sq. mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit The job incl P/F of 16 Amp SS combine - 02 jobs 5-pin socket points in 1.5 sq. mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit - 02 jobs Indicator points in 1.0 sq. mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit – 02 jobs Wall mounted fan c/w regulator switch, wiring in 1.5 sq. mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit and necessary fixtures – 01 job Exhaust Fan make c/w regulator switch, wiring in 1.5 sq mm multi strand PVC insulated copper conductor to be laid / carried in PVC channel/conduit and necessary fixtures – 02 jobs Distribution Board SP & N ( Regal Grey ) with 01 No incoming and 8 way outgoing, fitted with mini MCB “C” series 6A - 03 No for lighting points and 2/3 pin socket points and fans, 16 Amp – 01 No for heating points, 36 Amp MCB ( Mains ) – Havells or any other equivalent make

Providing of :- Matting comprising of 12 mm thick thermocool, jute matting, floor blankets = 120 sft Bedding – 2 sets each comprising of mattress – 01 No, Razai – 01 N0, double bed Excel / Korea Blanket – 01 No, Pillow – 01 No Providing of 15’ long bamboo rod with steel hook Providing of 15’ long bamboo ladder with equally spaced steps for easy accent Bed of size6’ x 6’ fabricated out of (ISA 40 x 40 x 5 mm) and 19 mm thick ply board Steel 1 5’ x 4 No + 6’ x 6 No = 42 rft

Supply of Tool Kit for maintenance of various lift schemes of the Sub Division The tool kit shall comprise of the following items All the items shall be of Taparia / Venus or equivalent make: i) Flat Spanner set of Size (4/5 to 30/32) (01 complete set) ii).Ring Spanner Set of Size (4/5 to 30/32) (01 complete set) iii).Cutting Pliers, 12 inch : (01 No`s) iv).Two in one Screw Drivers 18 inch /12 inch:( 01 No`s Each ) v).Hammer, I 8 Kg, : (01 No ) vi).Pipe Wrench 18 inch / 24 inch: (01 No each ) vii)Bearing Puller – 300 mm, 3- Jaw / Leg double ended mechanical bearing puller: (01 No) viii). Allen key set : 9 pcs, hanger packing type ( 1.0 mm, 1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm, 4 mm, 5 mm, 6 mm, 8 mm, 10 mm ix). Spirit level : 300 mm, 0.5 mm accuracy with magnet x).1 Kg capacity lever operated portable grease gun: (01 No) xi). Multimeter Rishabh make ( 01 No) xii).Tool Box : 250 mm x 260 mm x 495 mm 2 stroke, side pack, 52 cc diesel/kerosene brush cutter machine with all the allied attachments The tools are to be provided in a strong canvas bag

Carriage of material :

Gravel, sand etc from 25 kms Approx.

Cement from 5 kms Approx.

Steel from 5 kms Approx.

Roofing sheets, PUF sheets etc, tiles and other material

Cost to be deducted on a/c of available steel at site which shall be utilized during execution as per site requirement (874.665kg Approx..)