Sanitary and Plumbing at Accidental and Emergency Block at SNM Hospital.

Amount

Providing and fixing water closet squatting pan (Indian type W.C.pan) with100mm sand cast Iron Por Strap, 10litre low level white P.V.C.flushing cistern, including flushpipe, with manually controlled device (handle ever)conforming toIS:7231,with allfitting sand fixtures complete, including cutting and making good the walls and floors wherever required white vitreous china Orissa patternW.C.panofsize 580x440mm witht integral type foot rest

Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid,10 litre low level white P.V.C .flushing cistern, including flush pipe, with manually controlled device (handlelever) ,conforming toIS:7231,with all fitting sand fixtures complete, including cutting and making good the walls and floors wherever required :W.C.pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin withC.I./M.S.brackets15mmC.P brass pillar taps, 32mmC.P .brass waste of standard pattern, including painting of fitting sand brackets, cutting and making good the walls White Vitreous China Wash basin size 630x450mm with apair of 15mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipe sand fittings

Providing and fixing white vitreous china flat back half stall urinal basin of 580x380x350mm with flat White P.V.C automatic flushing cistern, of approved make with fittings, C.I/M.S brackets, standard size of C.P brass flush pipe, spreaders with unoins and clamps complete, (all in C.P brass) with waste fittings as per IS:2556, C.I trap with outlet grating and brackets, cutting and floores wherever required: Single half basin with 5 litre P.V.C white automatic flushing cistern of approved quality.

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P brass screws and washers complete.

Providing and fixing PVC, waste p[ipe for sink or basin including P.V.C waste fittings complete. Semi rigid pipe 32mm dia.

Providing and fixing CP brass towel rail complete with brackets fixed to wooden with brackets fixed to wooden cleats with CP brass screws with concealed fittings arangement of approved quality colour and make (Prayag or equivalent) 600 mm long towel rail with total length of 645 wide and effective high of 88mm, weighing not less than 190 gms.

Providing and fixing CP brass toilet paper holder C.P brass.

Providing and fixing soap dish of PTMT liquid soap C.P brass and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality colour and make, weight not less than 105 gms (Prayag or equivalent).

SOIL, WASTE AND VENT PIPES: Providing and fixing soil, waste and vent pipes. PVC 100mm @ 6kg/rm

PVC 75mm @ 6 kg/rm

Providing and fixing 100mm sand cast iron grating for gually, floor or Nahani trap

Providing and fixing P.trap for English type w.c with washer and M.S claps complete job

Providing and fixing double equal plain junction of required degree 75x75x75 pvc as per

100x100x100 pvc as per

WATER SUPPLY Providing and fixing 3 layer PP-R ( Poly propylene Random copolymer ) pipes SOR 7.4 UV stablized and anti- microbialfusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fitings 1/C fixing the pipe with clamps at 1.00 m spacing. This includes cost of cuttings chase and making good the same including testing of joints complete as per direction of Engineer-in-charge. (concealed work including cutting chase and making good the walls etc. 16mm OD nominal bore

32mm dia nominal bore

40mm dia nominal bore

Providig and fixing C.P barass bib cock of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 30 cm length n/b

Providing and fixing C.P brass angle valve for basin mixer and gyser points of approved make conforming to IS :8931 15 mm nominal type.

Providing and fixing C.P brass close hole basin mixer piller tap of approved quality and make, weighing not less than 1.970 kg 15mm nominal bore of standard back type.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked in indivating the BIS Licensse Np. With cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotus or equivalent having valid ISI license.)

Making connection of PPR. Distribution branch with G.I main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 20 to 32 mm nominal bore

Providing and fixing pvc gate valve with completed job 32mm dia pipe.

Providing and fixing puffing insulation to water supply pipe including 50mm thick extruded polystyrene insulation cover with nitrail sheet and 2 nd layer glass wood/ rock wool 50mm thick wrapping with steel meshing and finally cover with 0.6mm thick aluminium sheet, supporting the pipe with M.S flat iron in vertical line and bolt on wall 50mm screw, complete job 3240mm dia

20mm dia

providing and fixing heat tape 30watts of multi layer including wiring over pipe line in spring shape all complete job

Providing and fixing auto thermostatic temperature maintain upto 60degree centrigrade with required 2mm wire and switchs complete job.

Providing and fixing pufing insulation to water tank including 50mm thick extruded polystyrene cover with nitrial sheet and 2nd layer glass wood wrapping with steel meshing and finally cover with 0.6mm thick aluminium sheet complete job.

Constructing masonry Chamber 30x30x50 em, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C.1. surface box 100 x 100x75 mm (inside) with hi 11 yea C:1Ver fixed in cement concrete slab (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation, foundation concrete 1:5:10 ( 1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. with cement conc solid block 1:3:6

Constructing masonry Chamber 60x60x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C.I. surface box x 100x 100x75 mm (inside) with hi11yea C:Iver fixed incement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm niminal size) necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand :10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections make conforming of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber/ neoprene gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium HORIZONTAL

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately). WINDOWS

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer - in- charge. (Cost of aluminium snap beading shall be paid in basic item) with float glass panes of 8 mm thickness (weight not less than 20.0 kg/sqm).

Providing and fixing 12mm thick prelaminaed particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-1 type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Steel work in built up tubular (round square or rectangular hollow tubes etc) trusses etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washeres etc. complete Hot finished welded type tubes WATER TANK SUPPORT RECT SECTION

Providing and fixing PDM solid polycarbonate of thickness 8mm, single side uv coated, density as per testing method DIN 5036 i.e 8791 % including gasket, fitting in welded channel/built up frame of tubler, smoothing, priming coat of metal and metallic mechine spray high quality paint, screw and all necessary requirement complete job Sky light

Providing and fixing polycarbonate sheet with tripple layer 15mm thick having zig zag layer for more efficient including j hook, screw and all necessary requiement complete job. Water tank roof

Providing and laying roof insulation with 40 mm thick imprevious sprayed, closed cell free Rigid Polyurethane foam over deck/under slab insulation conforming to IS-12432 Pt. 111 (density of foam being 40-45 kg/cum), over a coat of polythene sheet over PUF spray, all complete as per direction of Engineer-in-Charge.

M/S TSEWANG DORJEY GOVT CONTRACTOR

M/S IMRAN KHAN

M/S ZAHID ALI