AR to PWD Rest House Beri

Amount

Scraping (HSR 8.32 a) (a) White wash and colour wash

Terracing consisting of tiles 22.86 cm x 11.43 cm x 3.81 cm. laid over 87.50 mm mud plaster and another layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm. Top of RCC slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc ( HSR 13.13).

Precast chequered terrazzo tiles 22mm thick in cement with marble chips of size and colour as required, laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry mixed with pigment to match the shade of tiles between joints and over the base in floors, treads of steps and landings, including rubbing and polishing (HSR 14.46)

Fixing and laying Marble stone flooring 17mm and above thick slab including matching grains of marble laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble including rubbing and polishing (HSR 14.49)

Kotah stone flooring minimum 25 mm thick in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1;3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing (HSR 14.62)

Laying and fixing vitrified/ceramic antiskid tiles of any size of approved make in floors laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. (Tiles shall be supplied by the Department) (HSR 14.93 )

Laying and fixing vitrified/ceramic/Glazed tiles of any size of approved make in skirting/dado, pillars, wall facing, laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles, (Tiles shall be supplied by the Department) (HSR 14.94 )

Laying and fixing Granite stone in all shades 15mm to 18mm thick in flooring, laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone(Excluding the cost of granite stone) (HSR 14.96 )

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12)

10 mm thick cement plaster 1:4 on under side of ceiling (HSR 15.52)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint(HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work (HSR 16.60)

Finishing walls with exterior decorative cement based paints such as snowcem, Robbiacem etc. on new work, two coats to give and even shade. (HSR 16.61)

Providing and laying two coats of exterior acrylic emulsion paint (HSR 16.79 (b) (Duplex , Asian, Nerolac etc.) (b) Ist Quality

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth eiht sand paper to get an even complete (J.K/ Birla make) (SHR 16.81)

Teak wood chowkats of doors and windows including iron hold fasts, corner straps, screws, bolts for hold fasts, etc., complete fixed in position. (HSR 17.13)

Deodar wood door and window shutters including iron hinges, screws, chocks/cleats and stores, etc., complete fixed in position (excluding the cost of tower bolts and handles but including the labour for fixing the same) (a) pannelled, glazed, or glazed and paneled (iii) 30 mm thick (12 mm thick deodar wood panel). (HSR 17.18a) 30mm thick

Teak wood wire gauze door and window shutters without springs housed in chowkats including chocks/cleats, iron hinges and screws, etc., complete fixed in position (excluding the cost of tower bolts and handles, but including the labour for fixing the same) (HSR 17.38(a) 30 mm thick

Providing and fixing commercial type block board, plain lining, butt jointed, including wooden plugs (teak) placed at 45 cm to 60 cm centres, complete with necessary nails (frame work shall be payable extra) (HSR 17.49 b) 19mm thick

Factory-manufactured paneled door or glazed window, shutters of commercial hard wood, such as hillock, champ, chikrassy and chaplash, etc., (non-coniferous timber other than teak, conforming to I.S. specification No. 1003, kiln-seasoned), with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks/cleats, stops, nails etc., complete fixed in position ( excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (a) 30 mm thick [HSR 17.90 (a)]

Factory-manufactured wire gauze door and window shutters of commercial hard wood such as hillock, champ, chikrassy and chaplash, etc. (non coniferous timber other teak, conforming to I.S. specification No.1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) (HSR 17.92 i) 30 mm thick.

Factory manufactured solid flush door shutters, with block board core as per I.S. No.1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II , fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)(a) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges (HSR 17.93 ai) (i) 25 mm thick

aiii- 35mm thick

Factory-manufactured paneled door shutters, of teak wood, kiln-seasoned, as per I.S. specification no. 401, with 100 mm wide vertical styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 12 mm thick veneered, particle board, or plywood of B.W.R. grade hot-pressed including cost of iron hinges, screws, chocks/cleats, stops and nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position) (a) Panel of decorative plywood, one side teak faced, and other side commercial faced. (HSR 17.94 ai) 30 mm thick.

a ii) 35 mm thick.

Supplying and fixing glass panes including special metal sash putty of approved make (HSR 18.30 b) Glass panes 4 mm thick upto 40sq. dm area.

Pressed steel sheet frames (chowkats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready-mixed paint red lead non-setting primer, of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (b) Door and window frame of size 76 mm X 38 mm with 35 mm wide single rebate (HSR 18.34)

(c) Door and window frame size 127 mm X 50 mm with 40 mm wide double rebate

Sh. Rishi Pal

Akash Goel

Parveen Deswal