NMDC/Doni/Works/7/26-27/ET/281

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion@ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m....All kinds of soil

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Ordinary rock .

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge....All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge..... ordinary rock

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Carriage of material by Mechanical Transportation including loading, unloading and stacking or levelling complete as directed by Engineer-in-charge. Earth, Lead upto 1.0. Km

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :...1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Stone work in plain ashlar in super structure upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : White sand stone

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. : Thermo- Mechanically Treated Bars of Grade Fe-500D or More.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm per coat

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservoir, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

Providing and fixing clay brick tiles for cladding, of approved make, in all colours, shades of any size as approved by Engineer-in-Charge, walls, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing precast Terracotta Jali , size of 300 x 220 x 85mm including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, including plastering of the jambs, sills and soffits.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete...Hot finished seamless type tubes

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of size 595 x 595 mm in true horizontal level OR minimum 12m thick PVC ceiling panels of approved shade and texture, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm center to center, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm center to center to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm center to center with 25 mm long dry wall screws @ 230 mm interval as directed by Engineer-in-Charge.

Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Flush/ Ruled pointing

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections

Applying priming coat with primer of approved brand and manufacturer, having low VOC (Volatile Organic Compound) content:

with water thinkable cement primer on wall surface having VOC content less than 50gm/ltr

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour….Two coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :-..Two or more coats on new work

Finishing walls with Acrylic Smooth exterior paint of required shade :...New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete….Fixed to openings /wooden frames with rawl plugs screws etc.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame Size 50x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800N (Face) & 900 N (Edge), minimum compressive strength 50 N/ mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) : 30 mm thick

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete….With 12 mm mild steel U beading

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width.

Providing and fixing bright finished Brass 100mm mortice latch and lock with 6 levers and a pair of handles of approved quality with necessary screws etc. complete Make DORMA/ENOX/HETTICH.

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass door latch with necessary screws etc. complete : 250x16x5 mm

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete

Providing and fixing bright finished brass casement window fastener with necessary screws etc. complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.

Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : .For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and Fixing of acid etched film as directed by the Engineer-in-charge for all designs with machine cutting etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing bright finished SS pipe pull handles with screws etc. complete : 300 mm Make : DORMA/ENOX/Hettich or equivalent

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand). Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Anti skid finish of size 1200x1200 mm or equivalent area.

Providing and laying Vitrified tiles in floor/wall in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Anti skid finish. Size of Tile 600 x 600 mm

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand)

Light shade pigment using white cement

Supplying, laying and fixing of 6.5mm thick vinyl flooring as badminton/TT/GYM Room etc court floors to provide optimum foot comfort and joint protection including cleaning and preparation of surface, cost of adhesive, rolling with wooden roller. All visible joints on the flooring to be sealed with special welding cords to make the floor seamless and safe for playing including labour cost etc. all complete as per direction of the Engineer In-charge.

Supplying, laying and installation of oralastic EPDM 36mm (30mm base layer + 6mm top layer) for outdoor kids play area including cleaning and preparation of surface. All complete as per direction of the Engineer In-charge.

Supplying, laying and installation of rubber indoor sports flooring for indoor kids play area, Gym, Zumba and Yoga of thickness 4.5mm, roll dimension 2mx15m, unit weight of 3.3 kg/sqm, abrasion resistance, inhibiting growth of microbes, including cleaning and preparation of surface. All complete as per direction of the Engineer In-charge. make ora sports 45 sports flooring.

Supplying, laying and installation of wood hevea flooring for badminton court including laying of 6mm polythylene paper on concrete, placing runner of pine rafter 38x70mm of the treated floor with top flooring of HEVEA (ABC grade) kiln seasoned and treated planks of size 20mm finishing thick with joint toungue and groove in size 120mm-7ft length shall be installed randomly on the runners having 20mm thick bio-power pads properly stapled at 12" distance. The gap between the wooden flooring and the surrounding tilead area will be 8 to 10mm on all sides of air circulation. Overall court thickness 78mm (excluding leveling packing thickness) including cleaning and preparation of surface. All complete as per direction of the Engineer In-charge. make ora wood hevea flooring.

Supplying, laying and installation of 9mm cricket pitch matte turf pile, ICC approved for pitch, of height: 9mm, stiches: 330/100, guage: 16/3", density: 71400 S/SQ, Dtex: 2200. size: 2mtr or 4mtrx25mtr. All complete as per direction of the Engineer In-charge. make ora sports 45 sports flooring.

Supply and installation for skating ring for all weather proof, skating system including epoxy primer N40, sand broadcasting, 1 coat of acrylic resurfacer SF101, 2 coats of Acrylic colour Kote T-50 and finishing the coat with PU RC WB (1K)

Synthetic and acrylic 5 layer system. Supply and applying for sports court all weather proof in 5 layer system with fabric membrane including all the materials required for the work. Layer 1 primer, two layers of acrylic resurfacer blended with silica sand, one layer textured colour coat, one layer colour coat highly resistance to all weather and ultraviolet degradation, then providing and laying of game line marking heavily bodied acrylic colour white striping paint, as per direction of the engineer in-charge.

Supplying and fixing badminton posts and net of standard size and quality including painting of the posts

Supplying and fixing of cricket net of standard size & quality, with length of 18.3m, material of net cord Nylon having colour green/black including parts of the net complete.

Supplying a pair of mild steel portable type Volleyball Pole of Height 8.5 foot with pole diameter of 4.0-4.5 inches having painted surface. Height of the pole can be adjusted ,should have hook for fixing of net.

Making/ Lining of floor of approved quality synthetic enamel/emulsion paint as per direction of the engineer in-charge.

Providing and fixing stone slab with table rubbed , edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick , fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the same stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 6 mm nominal size) as per direction of Engineer in charge and finished smooth. Granite stone of approved jet/ telephonic black shade

Providing and fixing 18mm thick gang saw cut mirror polished pre moulded and pre polished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade ... Area of slab over 0.50 sqm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) :

Medium shade pigment using 50% white cement and 50% ordinary cement

Extra for providing opening of required size & shape for wash basin /kitchen sink in kitchen platform, vaniety counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing edge moulding to 18 mm thick Granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge...Granite work

Constructing precast cement concrete block masonary (made of 50% cement concrete 1:5:8 in volume and 50% of 100mm granite stone in volume) manhole in CM 1:6 (1 cement : 6 coarse sand) RCC top slab 100mm thick with 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate of 20mm nominal size), foundation concrete 1:4:8 mix (1 Cement:4 coarse sand;8 graded stone aggregate of 40mm nominal size) inside plaster 12mm thick with cement mortar 1:3 (1 cement:3 coarse sand) finished with floating coat of neat cement and making channels with cement concrete 1:2:4 (1 cement:2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with floating coat of neat cement complete as per standard design.

Inside size 120x90 cm and 90 cm depth

Providing and Fixing square mouth S.W gully trap grade "A" complete with C.I grating , C.C solid Block masonry chamber of 300X300mm internal size with 200mm thick wall chambers, 100mm thick foundation concrete 1:5:10(1cement:5coarse sand:10 graded stone aggregate 40mm nominal size), covered with precast R.C.C slab of size:400X400X50mm provided with reinforcement steel bars of six no's of 8mm dia of each length 0.35mtr ( single mesh of 3no's each side), levelling with cement concrete on top of masonry walls of chamber with 40mm thick concrete and 12mm cement plaster 1:3 (1cement:3coarse sand)with floating coat of neat cement all complete as per directions of Engineer-in-charge. ..100 X 100mm size P type with C.C soild block masonry, made of 1:5:8 : (1cement :5coarse sand:8graded stone aggregate 10mm and down gauge) and 50% graded stone aggregate of 100mm and down size by volume of each block) with CM1:6 (1cement:6coarse sand).

Excavating trenches by mechanical or manual means of required width for pipes, cables etc. including excavation for sockets, and dressing of sides , ramming of bottoms for all depth including getting out the excavated soil and then returning the soil as required in layers no exceeding 20 cm in depth including consolidating each deposited layer by ramming watering etc & disposing of surplus excavated soil as directed within a lead of 50 meters. All kind of soil…..Pipe, cables etc, not exceeding 80 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall..25 mm dia. nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

Providing and fixing GI Pipes complete with GI fittings including trenching and refilling etc. External work

Providing and fixing GI pipes complete with GI fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anticorrosive bitumastic paint, cutting chases and making good the wall: 15 mm dia nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting & threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore

Providing and fixing G.I. Union in G.I. pipe including cutting & threading the pipe and making long screws etc. complete (New work) :

Providing and fixing gun metal gate valve with C. I. Wheel of approved quality (Screwed end):

Providing and fixing 2 way long body/ Automatic push cock/ pillar cock with wall flange of approved make heavy duty. Floor operated push cock of minimum weight 450gm

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. : 15 mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe….40 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions 45 CM length ..15 mm nominal bore

Providing, laying and jointing SWR rigid PVC pipe (Type B) confirming to IS:13592 with PVC solvent cement or using rubber sealing ring including testing of joints etc. complete.;110 mm dia SWR PVC Pipe

Providing, laying and jointing SWR rigid PVC pipe (Type B) confirming to IS:13592 with PVC solvent cement or using rubber sealing ring including testing of joints etc. complete.;75 mm dia SWR PVC Pipe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete...Door Bend 110mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Plain Bend 110mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Single Tee (Door) 110mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Door Bend 75mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Plain Bend 75mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Single Tee (Door) 75mm dia

Providing and fixing on wall face SWR PVC fittings/accessories confirming to IS : 14735 to SWR pipe including rubber sealing ring including testing of joints etc. complete….Nahani Trap with Jali 110x75mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm. weighing not less than 170 gms

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour.weighing not less than 300 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :...Rectangular shape 1500x450 mm

Providing and placing on terrace (at all floors levels) polyethelene water storage tank IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank .

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete...25 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

80 mm nominal bore Horizontal

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :

25 mm nominal bore

Providing and fixing PVC cowl, 110 mm.

Cutting holes up to 30x30 cm in walls including making good the same

With common burnt clay F.P.S. (non modular) bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required : Range of Two half stall urinals with 10 litre P.V.C. automatic flushing cistern

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore.

Providing and fixing Health faucet of "Jaugar" cat. No 573 with 1.00 Mtr flexible tube, wall hook and all fittings etc. complete.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing Oval shaped counter top wash basin with CI brackets, CP brass Pillar cock, CP brass waste coupling including cutting and making good the walls wherever required.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless-steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board ...610x510 mm bowl depth 200 mm

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore.

Providing and fixing Toilet Paper Holder Consider make GROHE Code No 40367001/ JAGUAR, KOHLER

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating.

Grading roof for water proofing treatment with Cement mortar 1:3 (1 cement : 3 coarse sand)

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes...110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°... 110 mm bend

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Shoe (Plain)...Shoe Plain110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion Shoe (Plain)...Coupler 110 mm

Providing and fixing Stainless Steel letters of Min size 5'' in height including moulding and fixing in position including cost of all necessary hardware, adhesive etc. completely.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugations as approved by Engineer -in-charge) of total coated thickness 0.50 mm(base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm)with zinc coating 120 grams per sqm as per IS:277, in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supply in single length upto 12 mtr or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surface, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm ) with Zinc coating120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7microns epoxy primer on both side of the sheet and polyester topcoat 15-18 microns using self drilling/ self tapping screws complete : Flashings/ Aprons.( Upto 600 mm)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Supplying and stacking at site. 90 mm to 45 mm size stone aggregate

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment):

Screened through sieve of I.S. designation 20 mm

Supplying and spreading of sand in lawn area, including watering, and dressing complete.

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Providing and Displaying Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the Engineer-in-charge.

Providing and Displaying of Aglaonema Sam plant ht.30 cm well developed three in one, having 18 to 20 fresh, healthy and attractive colorful leaves in 35 cm size Earthen pot/Chali/Tray & as per direction of the Engineer-in-charge.

Providing and displaying of Croton golden (Broad Leaves) plant, having ht. 60 cm to 75 cm with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot . & as per direction of the Engineer-in-charge.

Providing and displaying of Araucaria cookie plant, having ht. 60 cm to 75 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 20 cm size of Earthen pot/Plastic pot. & as per direction of the Engineer-in-charge.

Providing and Displaying Fishtail palm well developed with fresh & healthy foliage leaves of ht 210 to 240cm Specimen plant in 35 cm Cement Pot as per direction of the Engineer-in-charge.

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light watering with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of Engineer-in-charge.

Supply, Installation, Testing & Commissioning of Totally Anti-Corrosive Bobbin Wound filter of 1600 mm diameter. The filter plant should be specially designed for swimming pool application and should be moulded out of UV stabilized Re-inforced fiber glass ISO resin and chopped strand fiber mat with 12 mm wall thickness with Gel coat based pigmented, coulour tested for 6Kg/ cm² pressure and working pressure of 2.5 Kg/cm². All complete with 5 functions single lever operated , first charge multi graded Quartz Filter Media/ silica white sand, in built Filtration, backwash, rinse and drain systems. Fitted with pressure gauge panel, manual air bleeder, water drain and emptying plug and all other accessories complete. Fitted with collector arms and diffuser made from unplasticized PVC and poly propelene etc., all complete as per directions of Engineer-in-charge. The Filtration velocity should be 40m³/hr/m² Max. Working pressure : 2.5 kg/cm². and Flow rate = 125m³/hr. EN ISO 9001 :1200 Standard. (Make: Certikin, Emaux or equivalent)

Valve Battery: Supply, Installation, Testing & Commissioning of Valve Battery Manifold made in PVC with flanges for connecting to filters as per DIN 2501 standards. Consisting of set of 5 - butterfly valves for carrying out filtration, back-washing, rinsing and shut down of the filters etc., all complete as per directions of Engineer-in-charge. Size: 110 mm. DIN-2501 standard. (Make: Certikin, Emaux or equivalent)

Valve Battery Supports: Supply, Installation, Testing & Commissioning of Valve battery supports made in Zinc Plated Steel, Height: 2.30 m, all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or Equivalent)

Support Brackets: Supply of Box of accessories for 140 mm dia. pipe. consisting of 2 support brackets with antivibration clamps and screws.

Re-circulating Pumps: Supply, Installation, Testing & Commissioning of Cast Iron set of single stage re-circulating Pumps of 2900 r.p.m. with Mechanical Seal in Stainless Steel. I.P.-54 motor protection. Stainless steel AISI-420 shaft. With stainless steel AISI-316 strainer basket. Conn. PN-16 according to DIN2501 having flowrate: 50 m3/h @ 12m head and 4.4 HP Voltage 400 V/ 3 phase all complete as per directions of Engineer-in-charge. (2 working and 1 standby) (Make: Certikin, Emaux or equivalent)

Dosing Pumps: Supply, Installation, Testing & Commissioning of Membrane Dosing Pumps "EXACTUS" model. Electronic dosing pump to be mounted on its base as well as it should be mounted on the wall. Dosing Pumps should follow CE regulations and have IP- 65 protection. Power connections: 220/240V, 50/60 Hz. The materials in contact with liquid should be: Polypropylene, Viton, Teflon and PVC. The dosing pump should include anti-acid plastic case. Operating panel protection should be provided by a transparent polycarbonate cover. Lubrication should not be required. Flow should be 20 l/hr @ 5 bar. All complete as per directions of Engineer-in-charges. (Make: Certikin, Emaux or equivalent)

Chemical Storage Tanks: Supply, Installation, Testing & Commissioning of Semi-transparent polyethylene tank (PVC tank) of 200 Litres capacity with external scale so that levels can be checked easily all complete as per directions of Engineer-in-charge.

Agitators: Supply, Installation, Testing & Commissioning of Agitators provided with steering grip in bakelite, stirring rod of length 900 mm and propellor arms in PVC for easy installation in the tanks, all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Pool Drains: Supply, Installation, Testing & Commissioning of Stainless steel Drain grill of size 300 mm x 300 mm in AISI 304.EN 13451 with screws having standard Max. recommended flow 60 m3/h (0.5 m/s) all complete as per directions of Engineer-in-charge. (Make: EMAUX, Certikin, Pool Care or equivalent)

Suction Inlet <Vacuum Point>: Supply, Installation, Testing & Commissioning of Suction inlet in ABS with cap having internal thread of 1 1/2" dia. and external thread 2" etc., all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Wall conduits: Supply, Installation, Testing & Commissioning of PVC wall conduits 300mm long with rear connection to pipe by 2" etc., all complete as per directions of Engineer-in-charge. (Make: Certikin Model: FHD55, Emaux or equivalent)

Inlets: Supply, Installation, Testing & Commissioning of White ABS plastic bottom inlet nozzles for concrete with S.S. screws and regulable Flow/ inlet of 9,000 litres/hr. as per EN-13451-1 Standard for even distribution of treated pool water inlet all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Overflow Drains: Overflow gutter drain fitting with body and grille in ABS and screws of S.S. with connection of 2" dia. all complete as per direction of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Overflow Gratings: Supply, Installation, Testing & Commissioning of overflow gratings Made in white, U.V. Stabilized PP of Running Length: 1m, EN-13451-1 & EN-13452-1. Width: 295 mm, Height : 35mm all complete as per directions of Engineer-in-charge. The Price charged shall be per unit. (Make: Certikin, Emaux or equivalent)

Grating Support Profile: Supply, Installation, Testing & Commissioning of Made in plastic overflow grating profile EN-13451-1 & EN-13452-1 Suitable for 22, 24 and 35mm high grating Supplied in 1 m length all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Ball Valve of dia 50 mm

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Butterfly Valve of Dia 110 mm

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Flange and Adaptor for 110 mm dia. Installations

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Butterfly Valve of dia 140 mm

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Flange and Adaptor for 140 mm dia. Installations

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Butterfly Valve of Dia 160 mm

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Flange and Adaptor for 160 mm dia. Installations

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Wafer Check Valve of Dia 110 mm

Providing and fixing C.I. Control and Regulatory Valves all complete as per directions of Engineer-in-charge. Flange and Adaptor for 110 mm dia. Installations

Maintenance accessories: Supply of Metallic Vac- Head of size 350 mm with Clip connection all complete and operational as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of Extendable handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops, 10.0 mts. Long with Handle adapter all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of transparent blue plastic vacuum hose 11/2" dia. 30mtrs long including hose cuffs for connection to suction inlets all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of deep bag net made in polypropylene and white polyester netting shark all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of surface net made in polypropylene and white polyester netting shark all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of curved brushes made in polypropylene for pool basins and scum liners with netting shark all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of Algae brushes with stainless steel bristles all complete as per directions of Engineer-in-charge. (Make: Certikin, Emaux or equivalent)

Supply of Test kit for free chlorine & Ph all complete. (Make: Certikin, Emaux or equivalent)

Supply of Chemicals for dosing all complete: Chlorine Testing Tablets

Supply of Chemicals for dosing all complete: Phenol (pH) reagent

Supply of Chemicals for dosing all complete:. pH Plus in Bucket -

Supply of Chemicals for dosing all complete:. pH Minus in Bucket -

Supply of Chemicals for dosing all complete:. Algaecide in carton

Supply of Chemicals for dosing all complete:. TCCA Granules in drum

Supply of Chemicals for dosing all complete:. Flocculant in can

Providing and fixing total plumbing required for the Swimming Pool in uPVC pipe (06 / 10 Kg Pressure) including Fitting (Tee, Elbow, Socket, Bush, etc (excluding inlet and drain) all complete as per directions of Engineer-in-charge. (Make: Supreme, Finolex or equivalent). 63mm dia. in mtrs (10 Kg)

Providing and fixing total plumbing required for the Swimming Pool in uPVC pipe (06 / 10 Kg Pressure) including Fitting (Tee, Elbow, Socket, Bush, etc (excluding inlet and drain) all complete as per directions of Engineer-in-charge. (Make: Supreme, Finolex or equivalent).110mm dia. in mtrs (10 Kg)

Providing and fixing Lifeguard Chairs: Made in Stainless Steel AISI-304 with dismountable base plate. Steps, Platform, chair, including parasol holder made of polypropylene fibre-glass all complete as per directions of Engineer-in-charge.

Providing and fixing Diving Board: Diving Pool in light blue polyester and fiberglass boards with non- slip surface. Length of the diving board should be 3.2 m and width: 0.46m all complete as per directions of Engineer-in-charge.

Providing and fixing Diving Board Supports in structural steel: all complete as per Engineer in charge.

Providing Safety accessories: Life Buoys. (Make: Certikin, Emaux or equivalent)

Providing Lifeguard Loop. (Make: Certikin, Emaux or equivalent)

Drilling of NB 165 mm dia bore hole. Approx. depth of drilling for each borewell (2 Successful bore well) (However 02 borewells are accounted for probability of failure)

Providing and fixing NB 150 mm dia PVC casing pipe heavy duty

Providing and fixing PVC casing cap NB 150 mm dia for casing pipe

Supplying & fixing/laying at site of suitable pipes, reducers, bends, heavy duty collar, flange set, GI Nipple etc. including transportation to site.

Erection and commissioning of pumping machinery. This includes fixing of pump, alignment and balancing with all necessary erection of materials such as gland cable protector bolts, nuts, valve, gauge, etc. involved in the job of pump set erection, erection of panel board and metering board

Providing and fixing gun metal gate valve of approved quality (screwed end) 50/65 mm nominal bore.

Providing and fixing gun metal non return valve of approved quality (screwed end) 65/50 mm nominal bore, horizontal type

Earthwork excavation of required width of pipe cables, etc including excavation for sockets, and dressing of sides, ramming of bottom, depth upto 1.5m, including getting out the excavated soil and then returning the soil as required, one layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed with a lead of 50m pipe cable, etc, not exceeding 80mm dia

Providing and fixing in galvanised pipe (B-class as per IS 1239) 50mm dia normal bore with all fittings (earth work in trenches to be measured and paid for separately) including cost of all materials, labour charges, all equipment’s and testing complete as per specifications

Supply of new brand kirloskar make submersible pump set of (5.5-7.5)/(7.5 to 10) KW/HP 3 phase, 415V, 50Hz, AC supply model: KS6B-0814 suitable for 14 stage, 121 mtr head with gland packed arranged in standard material construction including transportation to site.

Supply and laying of submersible copper flat cable of size 3x4 sq mm with PVC sheathed of 1.1 KV class

Electrical Wiring for light/fan/exhaust fan/plug points

Wiring for light point/ fan point / exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing of suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Supply of PVC 4C x 185 Sq.mm Aluminium armoured Power cable of 1.1KV grade

Laying of PVC 4C x 185 Sq.mm Aluminium armoured Power cable of 1.1KV grade direct in ground including excavation, sand cushioning, protective covering, refilling the trench and providing cable markers along the cable path etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of following size on wall surface as required: Above 95 Sq mm and up to 185 Sq mm (Clamped with 25/40x3 mm MS Flat Clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 Cx185 Sq. mm (57 mm)

Wiring for circuit/submain wiring along with earth wire with 4x10 sq.mm + 2x6 sq.mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required

Wiring for circuit/submain wiring along with earth wire with 4x16 sq.mm + 2x6 sq.mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required

Supply of 15W COB Recessed Downlight

Supply of 15W Recessed Downlight

Supply of LED Spot Light 8W

Supply of LED Flood Light 150W

Supply of LED Flood Light 100W

Supply of LED Street Light 45W

Street Light post

Supply of LED Street Light-2 60W

Supply of LED Flood Light (Cluster) 150 W

Supply of LED Flood Light-2 (Cluster) 150 W

Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supply and fixing of 1 or 2 Module (75mmX75mm) GI Box along with modular base & cover plate for modular switches in recess etc.

Supplying and fixing 3 pin, 5 A ceiling rose including connections etc. as required.

Supply of Exhaust fans of 300 mm sweep along with all necessary accessories and complete in all respects. (Standard room pantry & Wash room)

Supply of Exhaust fans of 450 mm sweep along with all necessary accessories and complete in all respects. (Main Kitchen)

Supply, installation, testing and commissioning of BLDC 5 Star rating Ceiling fans of 1200 mm sweep along with all necessary accessories and complete in all respects.

Installation of up to 450 mm sweep exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

Extra for fixing the louvers/ shutters complete with frame for an exhaust fan of all sizes.

Supply and Installation of prefabricated LT MDB, 415 volt, for distribution of RAW supply and UPS supply with 630 Amps incomer & 23 outgoings

Supply and fixing of following 4 ways (4+12) surface/recess mounting, vertical type 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 Amps tinned copper busbar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required.

Providing and fixing 200 Amps 25KA, TPMCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

Providing and fixing 100 Amps 16KA, TPMCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required.

Supply of Copper Armoured 4C XLPE power cable 35 Sq.mm, 1.1 kV voltage grade

Laying and fixing of one number PVC 4C x 35 Sq.mm armoured Power cable of 1.1KV grade on wall surface as required.

Supplying and making end termination with brass compression gland and aluminium lugs for 4x35 sq.mm of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade as required

Supplying and fixing 8 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 12 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 16 way Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supply and fixing of Single Pole 16 Amps, 240/415 volt, 10KA, "C" Curve, MCB in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Single Pole 25 Amps, 240/415 volt, 10KA, "C" Curve, MCB in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Four Pole 25 Amps, 415 volt, Residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Four Pole 50 Amps, 415 volt, Residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Four Pole 63 Amps, 415 volt, Residual current circuit breaker (RCCB) having a sensitivity current 30 mA in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Four Pole 63 Amps, 415 volt, 10KA, "C" Curve, MCB in the existing MCB DB complete with connection, testing and commissioning etc, as required

Supply and fixing of Double Pole 32 Amps, 240/415 volt, 10KA, "C" Curve, MCB in the existing MCB DB complete with connection, testing and commissioning etc as required

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and laying 6 SWG G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/cable or at 0.50 meter below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm x 5 mm G.I. strip at 0.5 mm below ground as strip earth electrode, including connection /terminating with nut, bolt, spring washer as required

Providing and fixing 25 mm x 5 mm G.I strip on surface or recess for connections as required.

Supply of 500 KVA, 11KV/415 Volt, Dry type, outdoor, EEL2 transformer

Installation, testing and commissioning of transformer

Supply of 11kV, 3x95sq.mm, stranded compact circular Aluminium Conductor, Conductor screen with Extruded Semi conducting compound, XLPE Insulated, Insulation screening with Extruded Semi conducting compound in combination with copper tape, cores laid up, Inner sheath of PVC, Galvanised steel round wire armoured and overall PVC sheathed cable conforming to IS 7098/(Part-II) 1985 with the latest amendments. Cable code: A2XCEWY.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of size 95sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of HT grade of size 95 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Supply of 11kV, 3x95sq.mm, stranded compact circular Aluminium Conductor, Conductor screen with Extruded Semi conducting compound, XLPE Insulated, Insulation screening with Extruded Semi conducting compound in combination with copper tape, cores laid up, Inner sheath of PVC, Galvanised steel round wire armoured and overall PVC sheathed cable conforming to IS 7098/(Part-II) 1985 with the latest amendments. Cable code: A2XCEWY

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of size 95sq.mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of HT grade of size 95 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required

Providing, laying and fixing 150 mm dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching and re-filling etc as require

Supplying and making Outdoor cable end Termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for 95sq.mm of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Erection DP Structure using RCC Pole- 8 Mtr Long,115 Kg WL including supply of poles, erection of poles in depth of 1 meter incl. excavation and refilling, coping for the poles with CC 1:2:4 for 150mm around poles, Supply & fixing of Anti Climbing Device (12 Mtr GI Barbed Wire), Supplying 50 mm X 50 mm X 6 mm angle GI cross bracings & clamps, complete with 50 mm X 6mm GI flat iron clamps, bolts and nuts including drilling holes for insulator pins, bolts and nuts etc and painting with primer and finish paint as required

Supply and erection of H-Frame Set of GI steel (Incl. cross arms & clamps) for mounting 11kV GOS on the DP structure.

Supply and erection of 11kV, 400 Amps Double break GOS on the above H-Frame.

Supply and fixing of 11kV DOLO Cutouts for Transformer protection on the DP structure

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Excavation for foundation of structural steel angles for fencing in soft soil including dressing of sides and ramming of bottoms, lift up to 1.8 m including getting out the excavated soil and disposal of surplus excavated soil as directed

Providing and laying in position cement concrete 1:3:6 (1 cement : 2 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation including form work etc. s required.

Supply & erection of structural steel angles of 50 mm X 50 mm X 6 mm for erection of fencing and fabrication and erection of suitable size gate

Providing and fixing GI Chain link fabric fencing with a GI wire of 4mm dia, mesh size 50X50mm incl. strengthening with 2mm dia wire or nuts, bolts & washers as required complete as per the direction of Engineer-in-charge

Providing and laying Stone aggregate (single size) 20 mm nominal size in Switchyards after removing the existing aggregate, clearing the bushes and levelling the area as required

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 meter below ground for transformers and fixing with insulators on DP structures for Lightning Arrestors as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm

Supply & erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 kv overhead lines with rated voltage 9 kv (rms) with a nominal discharge current rating of 5KA and complete with galvanised clamping arrangement, G.I bolts, nuts, washers etc as required.

Supply of 2.0 TR Split Inverter AC 5 Star Energy rating along with 5 meter copper pipe, Stabilizer etc including installation and testing

Online UPS of Rating 3.0 KVA With Battery Of Backup Time 60 Minutes with 2 Years Warranty

G.I. Lightning conductor finial, Providing and fixing of lightning conductor finial, made of 25 mm dia. 300 mm long, G.I. tube, having single prong at top, with 85 mm dia. 6 mm thick G.I. baseplate having 4 nos. holes for fixing etc. complete as required.

Jointing of G.I. Finial Jointing of Copper/ G.I. tape (with another Copper/ G.I. tape, base of the finial or any other metallic object) by riveting/ nut bolting/ sweating and soldering etc.as required.

G.I. Tape on surface (Horizontal) Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run & Including insulating the wall)

G.I. Tape on surface (Vertical) Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run & Including insulating the wall)

Testing Joint of 20X3mm G.I. Strip Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

G.I. Strip below ground (32X6mm) Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

11KV HT Switch Board fabricated in 3mm CRCA sheet steel Panel (1No.) of Indoor Type with power pack (230V AC / 110V DC for trip circuit) Incoming Supply: 3.3kV, AC, 50Hz Vacuum Circuit Breaker of 12KV Rated (3.3KV Operating Voltage), Rated Frequency 50Hz, Rated Current: 800A, Rated Breaking Capacity: 31.5 KA for 3Sec. Short time withstand current with Motor Operated / Manual Spring charged operating mechanism, Trip Supervision Relay, Feeder Protection Relays, etc. with suitable aluminium busbar extended for providing outgoing connection, CTs, PTs, Relays, Digital Ananlog Meters, Indication Lamps etc., provided with necessary interlocking Protection system as per latest IS/IEC standards.

APFC PANEL: Supply, Installation, Testing and Commissioning of 250 kVAr Automatic Power Factor Correction (APFC) panel with APFC relay, CT's, PT's, indicating lamps, voltmeter, ammeter etc., of metal clad, modular construction compartmentalized cubicle design, IP-54 protection, free standing, floor mounted dust and vermin proof, indoor type compartmentalized powder coated of approved shade after antirust treatment (with min seven tanks) entire panel shall have interconnection Busbar and double earthing connection provision and cable gland plates. (Refer detailed specifications and drawing)

Total Rs

GST 18% Rs

Total Including GST Rs