PROVN OF CERTAIN SPECIAL REPAIR, LBW, REVENUE AND MINOR WORKS UNDER AGE B/R II AND AGE E/M OF GE (N) BIKANER AT MIL STN BIKANER

Amount

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for wall foundation etc or for shaft, well, cesspits, manholes, pier holes for laying of cable etc not exc 10 sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil

Removing excavated material not exc 50 mtr & depositing where directed at a level n.exc 1.5 mtr above/below the starting point.

Earth filling under floors or in foundation incl watering, ramming and consolidation complete.

Excavating in post holes (or similar holes) each not exc 0.5 Cum getting out, removing surplus soil to a distance not exc 50 m and making good surface.

M & L PCC 1:4:8 Type D2 using 40 mm thick greded stone aggregate as in foundations,filling and mass concrete.

M & L 40mm thick Damp proof course to horizontal or vertical surface incl necessary formwork with PCC 1:2:4 type B-1 using 20 mm thick stone aggregate & mixing of water proofing compound as per manufacturer's instructions.

M & L for 75mm thick PCC 1:4:8 type D-2 using 40 mm thick stone aggregate as sub base in floors.

M & L 40mm thick PCC 1:2:4 Type-B0 using 20 mm thick stone aggregate as in flooring.

M & L PCC 1:3:6 type C-1 using 20mm graded aggregate as in bed blocks etc for fixing windows, doors frames or other structural section as directed.

M & L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in kerbs, benching, hunching, corbelling and channels etc finished even and smooth using extra cement including necessary form work.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

Demolition of cement concrete (un-reinforced) in ground floors and paving n. exc 15 cm thickness.

M&L 40 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in sub base.

M & L for 50 mm thick PCC 1:2:4 type B1 using 20 mm thick greaded stone aggregate in floor sub base.

M&L Cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in copings/ coving etc. including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete.

M & L Hardcore of gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 cm thick, watered and rammed to a true surface.

M & L Brick work with fly ash bricks (old sized) straight or curved on plan exc 6m mean radius built in CM 1:6.

M & L Brick wk with Fly ash bricks, (old sized) straight or curved on plan exc 6 m mean radius built in CM 1:4 for manholes complete.

Demolition of Brick work built in cement mortar including all quions arches pillars etc but excluding ashlar facing dressed stone work and precast concrete articals complete.

M & L Bick work with sub class B bricks (old sized )straight or curved on plan not exc 6m mean radius in half brick thick walls built in CM 1:4 complete.

M & L for 10 mm thick Rendering in cement mortar 1: 4 on brick / concrete surfaces, finished Fair & even including mixing water proofing compound as per manufacturer's instns. ( WPC to be measured separately as supply only).

M & L Rendering 5 mm thick in in CM 1:4 on ceiling surface finished even and smooth complete

M & L Rendering 15mm thick in CM 1:6 on other than fair face of brick work surface finished even & smooth w/o using extra cement.

M & L Rendering 10mm thick in CM 1:4 on fair face of brick work surface finished even & smooth w/o using extra cement.

M & L for rendering 15mm thick in CM 1:4 ( in two layers ) on fair faces of brick work or concrete surface mixed with water proofing compound @ 3% by weight of cement , finished even and smooth without using extra cement. Note:- ( water proofing compound will be measured and paid separately).

Supply only Liquid water proofing compound of approved make.

M & L roughly squared stone lintels, beams, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete not exc 3m in length.

M&L Jodhpur stone roof slabs, self faced 7.5 cm to 10 cm thick, 25 cm to 35 cm wide, hoisted and set, jointed and grouted in cement mortar 1:3 complete.

M & L Non skid coloured ceramic tiles of size 300x300x7mm thick as in flooring jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 15mm thick screeding/ bedding layer in CM 1:6.

M & L Non skid coloured ceramic tiles of size 400x400x7mm thick as in flooring jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 15mm thick screeding/ bedding layer in CM 1:6.

M & L Glazed ceramic colour tiles of size 300x200x7mm thick as in dado/ skirting jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 10mm thick screeding/ bed plaster in CM 1:4.

M & L for Three coats of white wash on ceiling including preparation of newly plastered surfaces complete.

M & L for Preparing the new wood or wood based surfaces and applying two coats of synthetic enamel paints over a coats of pink primer complete.

M & L for two coats of Oil Bound Distemper on ceilings over a coat of primer as per manufacturer's instructions including preparation of newly plastered surfaces complete.

M & L for two coats of distemper oil emulsion over a coat of primer as per manufacturer's instructions on walls on newly plaster surfaces of walls incl preparation of surfaces.

M & L preparation of steel surfaces and applying two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer.

M & L for two coats of Cement base paint over a priming coat as per manufacturer's instructions including preparation of new plastered surfaces.

S & F Steel windows with side hung shutters including projecting type hinges with steel handles and steel pay stay, complete with glazing bars, dovetailed or welded.

S & F of steel ventilator with top hung shutter including hinges steel peg stay complete.

S & F Mild Steel Guard bars welded to steel frame of windows / ventilators etc. complete all as specified.

S & F 3mm thick Sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane.

S & F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete.

S & F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S & F in the steel frame at site as per specification.

S & F Butt hinges medium weight cold rolled mild steel of size 100mm.

S & F Aluminum anodised cast type handles 150mm size.

S & F 200mm long alumimium anodised barrel tower bolts extruded section.

S & F Vitreous china EWC(Pedestal pattern), white,(excluding flushing cistern and flush pipe), with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes etc.

S & F wash hand basin vitreous china size 550x400mm white flat back including CP pillar tap heavy duty as approved by GE including waste pipe ,chain plug,pvc connection, pvc waste pipe etc complete.

S & F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe and all fitting.

S & F PVC low level flushing cistern.valve .less, syphonic action type 10 liters capacity with inlet, ball valve, float and handle with including brackets and PVC bend pipe 90cm long etc. supplied and fixed.

S & F Rotational moulded polyethylene water storage tanks of capacity 1000 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seem-less perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for potable water. (ii) The tanks shall be white coloured with three layered wall and shall be ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes and ball valve shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.(iv) HDPE storage tanks shall be procured from the manufacturers as per Appendix “D”.)

S & F Ball valves 20mm bore high pressure of PTMT with epoxy coated alum rod and high density plastic ball screwed for iron pipe and fixed

S & F Bib taps cast copper alloy fancy type with crutch or butterfly handle screwed for iron pipe of 15mm bore and fixed

S & F Pillar tap cast copper alloy fancy type screwed for iron pipe on both ends of 15mm bore.

S & F Stop valve cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 20mm bore and fixed.

S & F Stop valve cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 15mm bore.

S & F PVC connections 15mm size with PTMT nuts of length 450mm.

S & F PVC( SWR) pipe of 110mm bore fixed to wall or laid in trenches complete.

S & F PVC( SWR) pipe of 75mm bore laid in floors or trenches.

S & F PVC(SWR) bend any radius of 110mm bore jointed with solvent cement complete

S & F PVC(SWR) bend any radius of 75mm bore jointed with solvent cement complete.

S & F PVC(SWR) junction double (Single tee) of size 75mm bore jointing with solvent cement.

S & F PVC(SWR) floor trap plain with grating including jointing with solvent cement of size 75 mm outlet.

Provision of soak well with excavation in ordinary soil ,foundation in PCC 1:3:6, wells of honey combed brick in CM, filled with brick bats comp. of size 4.5m depth 3.30 m dia at top and appx 2.40 m dia at bottom including necessary brick work ,conc. in fdn. ,stone patti roof slab, beam 02 Nos and 50 mm thick PCC over stone patti roof slab and all as per Drg BTD 265 sheet 1/1 all as specified and as directed.

M & L concrete bed to drain pipe in PCC 1:4:8 type D2 using 40mm graded stone aggregate incl packing under and hunching against sides of pipe after they are laid on slope and tested for 150mm dia bore sewer pipe line ( earth work excavation and sewer pipe line will be measured and paid separately)

M&L salt glazed stoneware pipes class SP3 confirming to IS 651-1972 in tranches and jointed in cement mortar 1:1 complete all as shown on drawings for 150mm internal dia of pipe. ( excavation and earth work will be measured and paid separately)

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including moulds, forms, mitered/stopped ends ( Inner girth will be measured ).

M&l Pre cast reinforced cement concrete 1: 2 :4 type B1using 20 mm graded stone aggregates as in manhole covers complete

M & L Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete.

M & L Jodhpur Stone slabs 7.5 cm to 10 cm thick in sunshades,chajjas,shelves, cills, landings,cover stones, templates, etc.n exc. 2m in length,punched dressed on face and along exposed edges,self faced on other side and set and pointed in in CM 1:4 complete.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required complete. (Internal dia of pipe 150mm).

S & F Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240

M&L Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

M&L Mild steel Tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe 410-0 or Fe 310-0.

M&L Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, complete.

M&L Mild steel Plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete Fe 410 -W (Gde- E- 250) quality-A.

S & F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

Dismantling cast iron or reinforced concrete drain pipe jointed in cement mortar pipes of any description of 75/100/150 mm dia bore complete .

Demolition of lime concrete of any description and thickness over roof slab complete.

Dismantling of Roof tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete.

M & L for applying a priming coat of cold bitumen primer @ 0.40 ltr/sqm as per para 11.44.5 of MES SSR Part-I complete.

M & L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. Not less than 150 gms/sqm) land on primed surface by forced application complete all as specified

M & L for Lime concrete terracing as on roof with minimum thickness of edge 40 mm and increasing uniformly towards ridge to obtain a certain chain slope of (1:40) as described in para 11.27.2 of MES SSR part-I complete. NOTE:- For lime concrete, mudia kankar (source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES schedule Part-I shall be used.

M & L for 40 mm thick brick tiles bedded on 10mm thick CM 1:6 and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete.

Ditto all as per Item above but except tiles complete as directed.

Taking down cement plaster/terrazo finish on brick or stone walll etc including raking out joints, hacking for key, scrubbing down with water etc complete.

M & L for Preparing new plastered or unplastered surfaces of walls and applying two coats of distemper Oil Bound, white or tinted over a coat of primer as per manufacturer's insructions including & over 3mm thick birla white wall care putty and rubbing down to obtain the smooth surfaces complete .

Taking up or down steel tubing and connections 15 mm bore including cleaning for refixing or removal to store complete.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store as directed complete.

S & F for GI tubing 15 mm dia, medium grade and fixed to wall and ceiling or laid in floor with all fittings complete.

Refixing 15mm bore old steel tubing and connections , in new or old position (walls, ceiling, floors, etc) complete.

M & L for 20mm bore Steel water tubes, medium grade, ISI marked, galvanised, with all fittings, fixed to walls and ceiling or laid in floors complete.

Refixing old 20mm bore steel tubing and connections , in new or old position (walls, ceiling, floors, etc) complete.

Dismantling floor hearth or wall terrazo or tilles in bath,.WC and kitchen etc including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises complete.

M & L for Non skid Ceramic coloured tiles 10 mm thick (square /rectangular) area of each tile exceeding 0.16 sqm but not exceeding 0.36 sqm, in skirting / dado on 10mm thick rendering on vertical surfaces in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

M & L for glazed ceramic tiles (coloured) 300 mm X 450 mm or 300 x 600 mm x 7-8 mm thick on vertical surfaces such as skirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match the surface over and including 10 mm thick rendering in Cement Mortars 1:4 on fair faces of brick work or concrete surfaces finishing rough for receiving wall tiles.

M & L for Non - skid Ceramic coloured tiles 10 mm thick (square /rectangular) area of each tile exceeding 0.16 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match match the shade of tiles laid over and including 15 mm thick screed bed in cement mortar 1:6 Complete.

Dismantling of Roof top Solar System equipments as required to facilitate the roof treatment and refixing the same after the work completed as dismantled complete solar panels, water tanks, GI fittings and other equipments and fitting pertains to solar system.

Provn of Septic tank of 50 Users complete with excavation of soft soil, PCC 1:4:8 type D2 below foundation, Brick work, RCC slab, vent pipe, vent shaft and steel cover as per TD Drg.all as specified and as diretced.

M & L Self adhesive membrane 1.5 mm thick self adhisive elastomeric SBS (Styrene Butadiene Styrene) bitumen based membrane with high density with geotextile finish on top provided with Pibial/ Emufal TE Bitumen primer @ 0.3 Ltrs/Sqm minimum over PCC, Laps shall be 50 mm on end sides and 100 mm on ends and as directed on site, and directed. Make- Sika, Texa India etc as approved.

S & F Gun-metal globe or gate valves, of 20 mm , with iron wheel head, screwed both end for iron pipe and fixed.

S & F PVC connections 450mm long 15mm dia with braided hose with M10x1 nipple 15 mm nuts, O Ring & rubber washer suitable for basin mixer Cat Part No : ALD-803AB.

S & F PVC connections 450mm long 15mm dia with braided hose with 15 mm nuts, rubber washer with out nipple Cat Part No : ALD-805B.

S & F for 100mm dia CI floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete.

S & F 100mm dia cast iron sanitary connection with sockets for WC out lets complete.

M & L 75 mm Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, but fixed to wall complete.

M & L 100 mm Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, but fixed to wall complete.

S & F 75 mm Cast Iron Bends (any radius), diminishing pieces or tapers (larger bore measured) and directed.

S & F 100 mm Cast Iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete.

S & F cast iron vent cowls 75/100 mm dia .

S & F Stainless Steel Curtain rods 25 mmdia with fixing brackets, stops, rollers etc Complete as specified.

M&L Aluminium anodised powder coated (Minium thickness of powder coating shall be 50 micron) work in doors, windows, ventilators including frames with one or more rebate including joining cleats for fixing etc Complete as specified.

M&L 5mm thick Sheet glass, ordinary quality in square of any required size complete as specified .

M&L Aluminium extruded section Door closer hydraulically regulateld, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35kg and fixed

S & F Mortice lock, vertical type, size 100mm ,4 levers brass metallic complete all as specified.

S & F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S & F 200 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed

S & F 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete

S& F Aluminium anodised medium weight Butt hinges 100mm long and fixed with steel screws complete

S & F for Vitreous china wash down water closet (pedestal pattern) Single Piece with UF soft close seat cover, hinges, fixing Accessories set and Accessories set, flushing cistern & fittings of size 385x710x730mm complete, including connection to drain pipe and S trap 300mm etc white / ivory in colour, Cat Part No QNS-WHT-7851S including hand shower (Health faucet) with 8 mm dia 1.2 mtr long flexible tube & wall hook with NRV( Back Flow Preventer) of Cat Part No -ALD-573 or equivalent.

S & F for Vitreous china wash basin, white, flat back, size 705x465x200 mm, Waste pipe, Waste coupling CP 32 mm dia and CP Connection of 450mm long of Jaquar Cat Part No-ALS-WHT-85601 Complete as specified.

S & F for Vitreous China Urinal with accessoriesset of size 375x315x620 mm of Cat Part No:URS-WHT-132530 including connection to flushing system, CP flush pipe and PVC 50 mm waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe,including metropole flush valve regular 40mm size concealed body with exposed shut off provision & 100mm Square plate of Jaquar Cat Part No-FLV-109 or equivalent3SQ and all fitting complete.

S & F for Single Lever Basin Mixer with popup waste and 450 mm long braided hoses of Cat Part No : ARI-3905B or equivalentcomplete.

S & F tumbler holder of Cat part No :AQN-7741 or equivalent.

S & F Soap Disc of Cat Part No - AQN7731OR ACN1131N or equivalent.

S & F of Towel Ring round or square with round flange of Jaquar Cat Part No-ACN-1121BN / CAN-1121N.

S & F Toilet roll Holder with stainless steel flap of Cat Part No :CAN-1153N/ AKP-35753P complete.

S & f self closing angle Valve for urinal with flange and 200mm long connecting pipe and spreder of Jaquar Cat Part No- ARI-39053 or equivalent.

S & F Glass self with Chrominium plated guard rail of Jaquar Cat Part No-CAN-1171N or equivalent.

S & F towel Rail CP fancy type of Jaquar Cat Part No-ACN-1101N/AKP-35701P.

S & F Towel rack Make Jaquar Cat Part No - AKP-3578P or equivalent.

M & L 20 to 25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20mm thick screed bed in cement and sand mortar 1:6 complete

M & L 20 to 25 mm thick machine cut kota stone slab as in skirting/dado etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 10mm thick rendering in cement and sand mortar 1:4

M&L 20mm thick granite machine cut slab table rubbed and polished granite as on cooking platforms incl. pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade laid over 20mm thick cement screed in cement mortar 1:6.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each and refixing the same door in same opening after easening etc. complete.

M & L for block boards 18 mm thick interior grade decorative choice type both side veneered complete

M&L 18mm thick plywood, 5Nos. ply grade BWP type BB fixed with nail to timber frame work fixed in repair complete all as specified and directed.

S & F decorative lamination 0.9mm thick complete

S & F second class soft wood (Kali) scantling clean sawn timber fixed to frame or as required on site complete

S & F Floor door stoper of aluminium body and tongue anodised with land drawn steel spring overall length of cover plate 140mm fixed with screw complete all as specified and as directed.

S & F decorative wooden beading fixed on edges of the shutter and as directed on site fixed with nails or adhesive complete

S & F wall mixer of Jaquar cat Part No - ARI-39145 or equivalent.

S & F Over head Shower with long arm Cat Part No OHS-1789 or equivalent.

S & F for Hook set of Six Stainless steel .

S & F Bib cock CP ARI-39037 Jaquar or Equivalent.

M&L Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

M&L Pressed steel framesof size 125 x 60 mm for doors with one or more rebatesincluding necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

M&L 35 mm thick Factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, 2nd class hard wood rail & style supplied and fitted to chowkats .

M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with rubberhard top finish with polymer admixture in any pattern or design over 15mm thick screed bed in CM 1:4

M&L mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

M&L Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm long.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 158 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 158 here-in-before but socket point on independent board complete as specifed as directed by Engineer - In - Charge

All as per item No 158 here-in-before but cable 2.5 Sqmm for 15 Amps switch socket outlet on independent board complete as specifed as directed by Engineer - In - Charge

All as per item No 158 here-in-before but one light point controlled by two 02 - way switch complete all as specified and as directed by Engineer-in-Charge.

S&F Switch piano flush type, Single pole 5 Amps, two way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Legrand/Wipro/Havells

S&F Socket outlet 2 in 1, 3 pin, 5A ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F switch socket combination 5 in 1, 5/16 amp flush type fixed on laminated sheet top cover (laminated sheet top cover is including in point wiring).

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings with LED Bulb 9 W complete all as specified and as directed by Engineer-in-Charge Cat Part No. SSK - LMS - 9W of make Syska/Havells/Phillips.

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge.

Supply & fix LED bulk head ,09W / 10 W, IP65 diacast aluminium housing powder coating finished complete all as specified and directed by Engineer-in-charge.

S&F Fan regulator electronic type, 230 Volt, 150 Watt 2 modules with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge.

Sheet metal enclosure for distribution boards, Double door suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make : Legrand / Schneider / ABB/ Havells

S& F MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/ GE/ Seimens/L&T/Indo Asian/C&S/ABB/Havells

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 415 volts with 200 Amps rated bus bar, load line DB's are fittied with bus bar nutural links blank plates TPN vertical load line 4 ways suitable for TP/FP 'A' frame MCCB,includeing 100 Amps MCCB -01Nos ,MCB SPN 32 -04 Nos and MCB SP as required, complete all as specified and as directed by Engineer-in-Charge. Make - Havells or equivelent Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/ABB/BCH/HPL Note :- DB's , MCCB & MCB shall be of same makes.

S&F Bell push flush type, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Bell Buzzer, Ding Dong AC 230 Volts, single pole ISI marked, complete all as specified and as directed by Engineer-in-Charge

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by Engineer-in-charge.

S&F concealed sub main wiring and providing new sub main wiring with 4 core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 4 sq mm drawn PVC concealed conduct including earth continuity conductor cable of size 4 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed by engineer-in-charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer-in-Charge.

Hanging only ceiling fan taking down vide item ser no 26 and connecting up with provn of 3 core of flexible cable of size 1.5 sqmm after complete rewinding ,over hauling, minor repair as required,painting and to make serviceable with replacement of bearing/ capacitor etc. complete all as specified and as directed by Engr-in-charge.

Switch piano flush type, Single pole 15 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : SSK /Leader

Socket outlet flush type, 3 pin, 15 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Legrand/Wipro/Havells

Socket outlet flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : - Legrand/Wipro/Havells

Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand/Wipro/Havells

Supply & fix LED T8 Tube lights ( Retro Fit ) ingress protection IP20 18W in make Cat Part No. SSK-TL-18W-I-HD in make Syska / Havells/Phillips with Connecting fixture for T8 tube light cat Part No. SSK-T8P-1201 ( 1*18w/20w 4 Ft) in make Syska / Havells/Phillips. complete all as specified and directed by engineer-in-charge.

Supply , assembling and hanging ceiling fans 1200 mm sweep single phase 230 volts ( Double Ball -Bearing ) with 01Set of 03 Blades, down rod, canopies, hook with rubber reel safety pins complete including making connection from ceiling rose to connector with twin core twisted flexible and PVC insulated copper conductor cable , 5 star Make : CG/ Havells/Orient /Khaitan regulator

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.00 sq mm 2 core

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.00 sq mm 4 core.

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.

Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.

M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.

Material and Labour Cross arm, bracings, stiffeners, supports, clamps, and back plates fabricated from structural steel section grade of Fe-290 (Grade E-165) such as channel angle iron, flat iron etc including nuts bolt swashers welding, bending cold or not drilling holes for bolts in any clamp or size including two coat of aluminium paint (under and finished coat) overa coat of primer (redoxide) after preparation of steel surfaces complete all as specified. Note:Unexposed surface shall be given one coat of primer only while computing the weight, the weight of paint shall not considered.

Suppy and Fixing LED based street light, housing made up of LM6 pressure die cast aluminium alloy with effectie thermal management, sturdiness. The fixture should have a minimum system efficiency of more than 100 lumen/watt and a minimum system lumen output of not less than 4500 lumens and maximum system wattage 45 Watts. The fixture shall have a correlated colour temperature of al least 5700K and CRI f minimum 70. The fixture shall be designed for a system life of 50,000 hours @ 70% lumen maintenance ingress protection of IP66 (lamp and gear compartment and mechanical inpact resistance raiting of IK>=08. The fixture driver should have an operating voltage range of 140-270 V & potted type for humming free operation, driver should be wthstand up to 440v for 8hrs, two surge proection not less than 5KV one on driver and one external surge protection, PF>0.95 and THD<10% and have double phase protection. LED light fitting should be suitable for ambient temperature from (-) 10C to (+) 50 C. The fixture should comply with the parameters IEC 60598 and LED should comply to IEC 61000-3-2 ed. 3.2 per harmonics IEC 61347-2-3,2006 in configuration with IEC 61347-1 ed 2.0,2007 for electrical safety LM 79 and for LED LM 80 test report needs to be submitted from the house NABL accreditation laboratory. Make CG/Philips/Wipro

All as per item No 194 here in before but 25 Watt LED street light.

M&L Pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 100 mm height, 65 mm dia. for working pressure 1100 volts grade, complete all as specified and as directed by Engineer-in-Charge.

S&F Shackle type, vitreous, white, brown, or green insulators, including galvanised mild steel strips, washers, insulators bolts, washers and nut for working pressure 1100 Volt, 100mm height 115mm dia, glavanised steel fitting strips of size 21 x 5mm, 14mm dia bolts complete all as specified and as directed by Engineer-in-Charge. Make : Bengal potteries/ Jay Sree/Bikaner ceramics/Mysore.

Supplying and stringing in replacement Aluminium conductor, steel reinforced (ACSR) any type of ACSR conductor as per site requirement of size /make as ordered including stringing for overhead line on LT poles including aluminum binding wire 14 SWG, jumpers, line tapes, conducting jelly etc complete all as specified and as directed by Engineer-in-Charge. (Notes : (i) The ACSR conductors shall be conforming to IS-398 and as specified in SSR Part-I.(ii) The unit rate quoted shall also be deemed to include for supply & fixing of aluminium binding wire, aluminium tapes etc which shall not be included in the weight of conductors.(iii) Weight of conductors shall be determined by measuring true horizontal distance between centers of two adjacent poles and compounding the weight of conductors of that size and length and 3% extra added for sag, jointing, jumpers etc. (iv) Weight of the conductors shall be calculated from the nominal weights given in tables in the relevant IS.)

Supply, laying and testing cable Cross linked poly-ethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with aluminium conductor, 1100 volts LT grade of cross-sectional area 10 Sqmm 02 core laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc supplied, fixed/ laid in repair including commissioning and testing complete all as specified and as directed by Engineer-in-Charge.

All as per item No 199 here in before but LT cable 120 sqmm x 3.5 core

M&L Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (8.5 metres long) , including painting of complete pole 8.5 m long with 2 coats of aluminium anti corrosive paints of first quality over a coat of red oxide primer including painting to pole upto 1.5m height from top of PCC coping with synthetic enamel paint 2 coat in black and white alternate strip including numbering in 8 cm height of number with white paint both paint aluminium/synthetic duly approved by Engineer in Charge complete all as specified and directed by Engineer-in-charge.

M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation for poles,filling and mass concrete complete all as specified and as directed by Engineer-in-Charge.

M&L Plain cement concrete (1:3:6) type C-2 using 20mm graded stone aggregates as in foundation for stays complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing thermplastic cable junction box with IP 66/67 weather prrof protection for outdoor installation with knockouts for cable entry of size 130x180x77 mm suitable for LT UG cable 10 Sqmm Make Hensel / Sintex

Supply & fixing FRLS PVC insulated Copper conductor, two single core of size 1.5sqmm complete for terminal box to street/ flood light fitting.

Material and labour Earthing complete with galvanised iron earth plate electrode of size 60 x 60 x 0.60 cm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI wire 4 mm dia by means of GI bolts/nuts/washers, protected by 15 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh,RCC cover & frame, PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR Part – I. (For Poles) Note:- The unit rate inclydes earth lead upto 7.5 metre length from top of earth plate.

Material and labour Earthing complete with galvanised iron earth plate electrode of size 60 x 60 x 0.60 cm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including GI strip 32 mm x 6 mm by means of GI bolts/nuts/washers, protected by 40 mm bore GI light grade pipe. Earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15 cm thick all around bottom and top. 20 mm bore GI light grade pipe for watering and including funnel, wire mesh,RCC cover & frame, PCC (1:3:6) type C2 (using 20 mm graded crushed stone aggregate) as in earthing pit including necessary excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR Part – I. (For LT Panel) Note:- The unit rate includes earth lead upto 7.5 metre length from top of earth plate.

Supplying and laying un-reinforced precast concrete cable cover, Class LV, Type I, flat, size 250 mm x 150mm x 40mm

Boring of holes under road, pavement, hard standing by using boring system complete all as specified and as directed by the Engineer-in-charge.

Supply and fix galvanized iron pipe light grade ISI Marked complete for cable protection and LED brackets, laid in trenches, floors, fixed to walls, pole with suitable FI clamps complete all as specified and directed ISI marked. of following sizes. (a) 80 mm bore.

(b) 40 mm bore

Cable indoor / outdoor end terminals jointing kit for LV/LT 1100 V cable heat shrinkable type joint kit complete with RBYB coloured sleevs 04 Nos 45 cm long, jointing material and accessories, thimbles etc suitable for120 Sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing, fixing in replacement complete all as specified as directed by Engineer-in-Charge.

Supply, fixing and testing refrigerator electric driven 230 volt AC 50 Hz capacity 165 ltrs ltrs frost free with inverter linear compressor, linear cooling, dual fridge , multi air flow , smart diagnosis and auto smart connect , double door, BEE & minimum 3 star rated and with inbuilt inverter and necessary connection complete all specified , Make :- LG /Whir Pool/ Voltas .

Supply, installation, commissioning and testing of water cooler of stainless steel, electric driven, single phase, having approx storage and normal cooling capacity of 60 ltrs per hr and storage capacity 120 ltrs (R 134 a environmental friendly gas ) including provn of PVC connection heavy duty 750 mm long with brass union both end suitable for 15 mm bore GI pipe water connection and necessary connection complete. Note:- (i) Rate deemed to be included cost of PVC connection, drain pipe etc.(ii) Water cooler shall be make USHA /Blue star/Voltas Model No.Tushar 60/120 PSS .

Supplyand install Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type& designed for input variation between 170 V to 250 V with out put voltage stabilized at 230 Vwith accuracy of ± 2.5% and of capacity 4 KVA complete all as specified and as directed by Engineer-in-Charge. Make :- AE/ VOLINA/ BLUE BIRD / V Guard

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 2.5 Sq mm single core in and including new non-metallic rigid PVC casing & caping not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 2.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 2 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard.

S&F MCB suitable for 6 to 32 Amps, 240 Volt AC supply single pole and neutral with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge.

Supply and fix galvanized iron pipe medium grade ISI Marked complete laid in trenches, floors, fixed to walls, pole complete with all fittings all as specified and directed ISI marked. of size 15 mm bore.

BIDAWAT ENTERPRISES

durga construction company