Construction of Aspirational Public Toilet at UPHC at ward no 23 in Old panchayath office road in Bhavani Municipality

Amount

Earthwork excavation and depositing on bank within initial lead of 10m and initial lead of 2m as sand silt or other loose soil wet sand light black cotton soil ,hard red earth sheles hard red earth mixed with small size boulders etc.complete as per standard specification

Cement concrete 1:4:8 mix ( one cement, two sand and Eight Aggregate ) using 40mm ISS brick jelly cost and of mixing, placing, compating, curing, including cost and conveyence of all meterials etc., complete

Centering for soffits of R.C.C slab plain surface including structting up to 3.00m height using mild steel of size 90cm x 60cm 10 - gauge fited with M.S angle of size 25 x 25 x 3mm laid over silver oak (CW) joist of size 10cm x 6cm spaced 90cm c/c and supported by causirana props of 10 to 13cm dia spaced @ 75cm c/c complete compailying as per standard specification.

Reinforced Cement concrete 1:1.5 :3 (one cement, one and half M.sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete.

Brick work in C.M 1:5 mix (one cement & Five sand) using Chamber brick size (9" x 43/8 x 23/5 cm) including cost and conveyence of all meterials to site and all labour charges etc., as per standard specification. - (10 m3)

Supply and fabricating and placing in position of M.S. or RTS of steel rods to required size and length as directed by the departmental officers including cost of binding wire, cutting, tying etc., including cost and conveyance of all materials etc., upto 16mm dia.

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Flooring finishing with Ceramic tiles of size 30 cm x 30 cm laid in cement mortor 1:3 mix to 20mm thick and paint with cement paint 0.40/cm2 including finishing jointing and put with tiles surface as complete etc.,

Supplying and fixing of110 mm P.V.C rain water down fall of pipes of 100mm dia, with necessary Bend, Tee & showe, plug, clamps etc., complete as per standard specification.

Plastering with cement mortar 1:5 (one cement five sand) mix to 12mm thick including cost and coveyance of all materials to site finishing curing etc., complete.

Plastering with cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 10mm thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Painting two coats for Interior surface with approved Interior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter and should have provision to fix AL drops, tower bolt hinges and lock plates inclusive of cost of all materials etc. complete complying with thew standard specifications.

Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed SC copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point (for electronic regulator) (5 points per coil (SD 22)

supplying and fixing of 18w LED Tube light fitting 4 Feet from approved qulity including all cost and conveyance of labour charges etc complete

Conducting Geophysical survey to find out the water table including cost for convey the instrument to the site and other charges

Drilling of 150 mm dia vertical bore in hard rock area of any required depth as directed by the departmental officers including labour charges for inserting casing pipe assembly in the drilled holes excluding cost of 180 mm PVC casing pipes of required length including transportation charges for rig and supporting vehicle from one place to another place etc., complete complying with standard specification.

Upto Casing Pipe depth

Beyond the depth of Casing pipe

Supplying and inserting PVC casing pipe 180mm diametre without slots for inserting in the drilled hole including jointing the pipes, etc., complete as directed by departmental officers

Supply and delivery of 32mm dia UPVC Column pipe cristal coupler type,screen pipe with ISI mark including cost and conveyance of Materials at site etc., Completed.

Supply and delivery of Three Phase submersible pumpset 40Lpm x 100m head with ISI mark as per IS 8034/2002 without panel board including cost and conveyance of Materials at site etc., Complete.

Supply and Delivery of direct online starter confirming to ISI3947 and IEC60947-1 suitable KW rating for operation in AC/Three Phase/50HZ (+- 5%) and 415V(+-10%) including Ammeter,Voltmeter,Themal Overload relay, 16Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off push button swiches, 5 way connector, wiring with 1 sq.mm/1.5 sq.mm copper PVC insulated cable,PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately) Suitable for 5HP Submersible motor including cost and conveyance of Materials at site etc., Complete.

Supply and delivery of following GI Pipes (Medium) as per IS 2239/part I/90 including cost and conveyance of all materials etc., complete.

20mm dia GI Pipe

32mm dia GI Pipe

40mm dia GI Pipe

Supply and delivery of following GI Specials with ISI mark including cost and conveyance of all materials etc., complete.

20mm dia GI Coupler

20mm dia GI Tee

20mm dia GI Elbow

15mm dia CI Tap

20mm x15mm dia GI Reducer elbow

32mm dia GI Elbow

32mm dia GI Union

32mm dia GI Tee

32mm dia GI Hex Nipple

32mm dia GM Gate valve

32mm dia GI Coupler

32mm dia GM non return valve

40mm x 32mm GI Reducer Coupler

32mm x20mm GI Reducer Coupler

40mm dia GI Coupler

40mm dia GI Elbow

40mm dia GI Tee

40mm dia GI Hex Nipple

40mm dia GI Union

40mm dia GM Gate valve

Bore well dummy plate

Bore well MS Clamp set

11/4" dia hose Adopter

Nylon rope

11/4"dia PVC Tank Connector

Laying of following GI Pipes and Specials to proper line and level including jointing but excluding cost of pipes and jointing materials including all labour charges etc., Completed.

20mm dia GI Pipe

32mm dia GI Pipe

40mm dia GI Pipe

Labour charges for the erection of submersible pumpset in borewell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete.

Supply and fixing of following PVC (rigid) Pipes (1.8mm thick) with ISI mark including cost and conveyance of Materals at site etc., Completed.

25mm dia PVC (rigid) Pipes (5/8")

25mm dia PVC (rigid) bend (5/8")

Supply and run of 4 of 6 Sq.mm (84/.03) PVC insulated SC unsheathed Cu conductor of 1100 V on 7/20 GI bearer wire for service connection mains.

Supply and run of 4 x 6Sq mm(56/0.3) PVC insulated Sc unsheathed cu conductor of 1100 V grade in 32 mm dia GI pipe (class B) suitably bent at both ends with necessary angle iron upright and end supports for main (service pipe)

Supply and fixing of following Electrical materials including cost and conveyance of all materials and labour charges etc., complete.

TW Plank of size 600mmx450mmx19mm with supporting reepers of 1" thick on both side with painting and with bolt,nut and washer etc., complete.

Supply and fixing of 32A porcelain fuse Unit (500V)

Earth Link (1"x1/8") copper flat

32A Double pole MCB with metal box

Supply and Fixing of 4.00 sq.mm PVC Insulated and sheated 3 core flat copper cable confirming to IS 694/1990 including cost and conveyance of Materals at site etc., Completed.

RGC CONSTRUCTION (BID ID -1299873)