PROVN OF SHED AND FABRICATION OF WIRE MESH/IRON GRILL ENCLOSURE AT EO LAB AND PROVN OF GREASE TRAP AND ALLIED WORKS AT MESSES AND CAFETARIAS AT 9BRD AFS PUNE UNDER GE AF LOHEGAON

Amount

Excavating in post hole or similar hole each n.exc. 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc. 25 cm, watering and removing surplus rock to adistance not exc. 50 mtr in soft disintegrated rock complete all as specified and as directed.

M&L PCC (1:2:4) type B2 using 40 mm graded stone aggregate as in foundations, filling & mass concrete complete all as specified and directed.

M & L Joist, channel, angle, or tee sections, fixed independently in vertical Posts, without connecting plates welded etc. Fe 410-W (Gde E250) quality-A

S&F rolled section as in main & cross beam , hip and jack rafter & purlins where connected to common rafter and running rails etc complete using Fe 410 -W (Gde- E- 250) quality- A all as specified and directed.

S&F Steel work in tubular trusses in roof truss including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete Fe 410 -W (Gde- E- 250) quality- A all as specified and directed.

S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,with riveted, bolted or welded attachmentFe 410-W (Gde E250) quality-A

M&L two coats of synthetic enamel paint over one coat of red oxide primer on new steel surface after necessary preparaton of surface over 10 cm in width or girth complete

S & F Pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L for hardcore of gauge n.exc 0.63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface of a broken stone or boulders complete all as specified and directed.

M&L for 100mm thick PCC type D2 (1:4:8) using 40mm graded agg as in flooring complete all as specified and direcetd.

M & L for sand cushioning for laying paver block or sand filling under floors in foundations including watering and consolidation.

M&L for laying machine pressed precast concrete interlocking paver block 60 mm thick any shape and size and colour confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for plain cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) as in copings all as specified and directed.

M & L Framed work such as grills, gratings, etc.. with ends of bars shouldered/welded and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, handels and locking arrangements, complete all as specified and directed.

M&L for Welded steel wire fabric supplied and fixed complete to wood or steel members of approved size and make wt n exc 4 Kg/Sqm complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide & n.exc 1.5m depth for fdn etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in soft disintegrated rock.

M&L for returning, filling incl spreading levelling watering and well ramming in layers n.exc 25 cm as in soft disintegrated rock.

M&L for Removing excavated surplus rock n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point.

M&L for Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius in CM 1:6 complete.

M&L rendering 15mm thick on brick work or concrete surfaces in CM 1:4 and finished even and smooth without using extra cement all as specified and directed.

M & L for prepartion of newly plastered surfaces on walls and applying two coats of cement based paint over a coat of primer on wall complete all as specified and directed.

M&L for Excavation in trenches n.exc 1.5m wide & n.exc 1.5m depth for fdn etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5 m in depth and getting out in hard/dense soil.

M&L for Excavating over areas, n exc 1.5 m deep and getting out hard dense soil.

-ditto- all as per item No 2 above but exc 1.5m and n.exc 3.00m

M&L cutting into existing manhole for connecting new drains making good to pipe and rendering cutting out existing bencing for and forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required 150mm dia(Note : work in foul position)

M&L for 150mm dia RCC drain pipes class NP2 laid in treches & jointed with collars etc complete.

M&L for Concrete bed (1:3:6) type C2 to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested. (dia-150 mm)

Demolition of cement concrete in flooring and pavings exc 15 cm thick below or above ground level .

M&L for cement concrete in foundations, filling and mass concrete using type D2 1:4:8 (40mm graded stone aggregate).

M&L PCC 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in benching of manholes and in drain and channel in cement concrete complete all as specifed and directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping including formed work for man holes, drains and fixing of RCC OH tank covers etc complete all as specifed and directed.

M&L PCC solid block masonry 1:3:6 built in Cement mortor 1:6.

M&L rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surface in internal surfaces with water proofing compound. (Note : WPC shall be measured and paid seperately)

M&L rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surface in external surfaces.

Supply only liquid water proofing compound as per manfacture instruction

M&L RCC precast (1:2:4) type B1 using 20 mm graded stone aggregate in Manholes covers set in CM 1:4

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M & L PVC (SWR) pipes 110mm single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified and directed

M & L PVC (SWR) pipes 75 mm singlesocketed in any length with rubber ring joints laid in trenches or floors complete all as specified and directed

S&F PVC (SWR) bends any radius bends with oval acess door plain 110 mm bore

S&F PVC (SWR) bends any radius bends plain 110 mm bore

Same as item no 24 bends plain with oval acess door 75mm bore

Supply and Fixing of NS10 Grease Separator plant as per DIN EN 1825 and DIN 4040 100 suitable for underground installation. The Grease Separator should be made from polythylene. The Grease Separator should have Nominal capacity of the NS10 with Inlet/Outlet socket of DN150. The overall capacity of the grease separator should be 2170 litre with grease storage capacity of 415 liter and sludge storage capacity of 1005 liter. Total weight of grease separator is 128 kg with overall dimension of the 1340mm x 2828mm (D X H). The Grease Separator should be capable of cleaning via shaft manhole cover, emptying via suction line DN 65 PN 10 with PE couplings for two-sided thread connection 75/75 mm for suction line, fire hose quick coupling 75 B and 2 1/2 blank cap, Counter flange with fire hose quick coupling 75 B and 2 1/2 black cap. The Connections for inlet and outlet should be as per DIN 19534 and DIN 19537 and Building Supervisory Authority approval Z 54.1 509. Top cover of the Grease Separator plant should be made from Concrete frame with cast iron cover having clear opening of 600 mm diameter. The cover should be odour-free when closed. The weight of the cover should be 145 kg and manufactured to meet A15 load class requirement. Make : ACO Passavant or equivalent

Shri Sant Cosntruction (BID ID -3500129)

tulsani associates (BID ID -3507833)

BSK Construction (BID ID -3501869)

santulan & Company (BID ID -3497382)

EAST PUNE SERVICES (BID ID -3499692)