Construction of way side amenities near Mubarikpur between NH-503 (Extn.) and Mubarikpur bye pass road Part -II

Amount

Excavation in foundation trenches etc. in earth work in all kinds of classification of soil such as pick work, jumper work, pick jumper work, blasting work, soft and hard blasting and doing work in saturated soil, including chiseling or wedging out rock where blasting is prohibited, or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during dewatering, removal of slush and stacking the excavated soil clear from the edge of excavation with in all leads, as directed by Engineer-in-Charge and then returning the stacked soil in 15cm (fifteen centimeters) layers when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as directed by Engineer-in-Charge with in all leads and lifts, disposed earth to be levelled and neatly dressed including carriage of materials within all leads and lifts.

Providing and laying mechanically mixed and vibrated concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone aggregate (40mm) (forty millimeter nominal size) for plain/cement concrete in all heights/depths, in open foundation or under water, including pumping or bailing out water/ dewatering (surface and sub-soil water) and removal of the slush which may arise at the time of laying under water, for all heights/depths and any quantum of water, including cost of form work and curing complete in open foundation and the like etcetera complete, as per drawing and MORD technical specification section 800, 900, 200 and 1600 as per the satisfaction and the direction of Engineer-in-Charge including carriage of materials within leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, GST, toll tax, sales tax or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3 (one cement : one and half sand : three graded crushed stone aggregate 20mm (twenty millimeters) nominal size) mix designed so as to give a compressive strength corresponding to Grade M-25 (M-Twenty five) with minimum cement content of 400 Kg/cum (Four hundred kilograme per Cubic Meter) excluding the cost of form work and reinforcement for reinforced concrete work in all depths/thickness and upto all floor level, complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, royality, octroi, toll tax, sale tax, GST or any other taxes imposed by the Government.. (i) In foundation & plinth beam, columns, beams, griders, lintels and suspended floor roofs, landing at shelves, cantilever.

Providing Mild Steel / Tor Steel reinforcement of R.C.C. work including bending, binding and placing in position complete up to floor two level of make Tata/ Sail as approved by engineer - in- charge. Make (TATA or SAIL)

Providing form work with steel plates 3.15m thick welded with angle iron frame in 30x30x5mm so as to give a fair finish including centering ,shuttering,shutting and propping etc. with wood battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4 mtr and removal of the same for insitu reinforcement concrete and plain concrete work in a flat surface such as soffits of suspended floors,roofs,landing and the like.Floor etc. up to 200mm in thickness (Vertical Surfaces) columns, beams, lintels as per direction of engineer - in- charge.

Steel work welded in built up section,trusses and framed work including cutting, hosting, fixing in position and applying a priming cost of red lead paint in beams joists channels, angles, tees, flats with connecting or angles cleats as in main and cross beams, hips and jack rafters, purlins connected to common rafters and the like in railing and edging of steps etc as directed by engineer -in - charge.

Steel work welded in built up section Anar kali type cast iron jali work including cutting,hosting,fixing in position and applying a priming coat of red lead paint in grating framed guards, bars ,ladders, railing and similar works.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:5 (1 Cement : 5 Sand) using 1st Class bricks.

Brick work using common burnt clay building bricks in Cement Mortar 1:5 (1 Cement : 5 Sand) using 1st Class bricks in super structure.

Half brick mansory in common burnt clay building bricks in Cement mortar 1:4 (1 Cement : 4 Sand) first class bricks in super structure

6mm Cement plaster to ceiling in cement mortar 1:4 (1 Cement :4 Sand)

15mm cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering up to floor two level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth and finished even and smooth as directed by the engineer-in-charge. Cement Mortal 1:5 (1 Cement 5 Sand)

Finishing walls with water proofing cement paint of approved brand and manufacture Nerolac suraksha plus/Apex exterior and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt and remains of loose powdered material as per the direction of engineer -in- charge.

P/F glazed tiles 6mm thick in skirting risers of steps and dado on a bed of 12mm thick cement mortar 1:3 (1 Cement :3 Sand) finished with flush pointing in white cement tiles of approved brand and make , kazaria, Johnson, somany as approved by engineer in-charge.

Applying Birla white wall care putty over plaster surface after throughly brushing the surface free from mortar droppings as approved by engineer -in-charge.

Providing and fixing double Charge vetrified tiles 600x600x10mm (Six hundred into six hundred into ten millimetre) thick impact resistant heavy duty vetrified tiles of Kajaria, Nitco, Orient/Bell/Rak/SIMPOLO of approved shade and colour in flooring, laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required up to all floor levels, complete as per HPPWD specifications and approved drawings, design and as directed by the Engineer,-in-Charge, including carriage of material within all leads, lifts, and other incidentals. The rate is including Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government.

Providing and laying black granite stone in wash basin counter and partition for urinals including rounf moulding and cutting for counter wash basin 20mm (Twenty millimetre) thick laid on base of 20mm thickness of cement mortar 1:3 (One cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing, nosing and polishing complete as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and Laying filling of brick bats complety compacted in floor after laying sanitary PVC like fitting in bath room.

Providing fixing aluminium andodised powder coated pattern to aluminium door frame section with standard panels in windows i/c fixing with aluminium frames all powder coated completed in all respect complete with fitting , fixtures.Doors Size 2' 6"x6' 9"

Providing fixing aluminium andodised powder coated pattern to aluminium door frame section with standard panels in windows i/c fixing with aluminium frames all powder coated completed in all respect complete with fitting , fixtures.Doors Size 3' 3"x 8'

Kota stone slab flooring minimum size 55x55 cm. 20mm thick base of cement mortar 1:4(1 cement:4Sand)laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete 20mm thick. In design pattern as per direction of engineer - in -charge

Providing and fixing top cover for rolling shutters. Shutters having width below 3.5 meter

Providing and Fixing POP cornice on roof slab ceiling and wall corners with plaster of paris cost -in -situ as per direction of Engineer-in-charge. Complete in smooth finish. On Roof -polion

Providing Fixing POP moulding on ceiling with plaster of paris cast - in -situ as per direction of Engineer-in- Charge. Complete in smooth finish. On ceiling.

Supplying and fixing rolling shutters of approved make made of 80mmX1.25mm M.S. laths interlocked together through their entire length and joined together at the end locks mounted on specially designed pipe shaft with brackets side guides and arragngement for inside and outside locking with push pull operation complete but excluding the cost of the top cover and spring. Shutters haveing width below 3.5 meters.

Providing and fixing 0.60mm thick prepainted steel sheet (Make Tata or Kamdhenu )in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coated of 20 microns over 5 microns primer coating to track coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J&L hooks,bolts and nuts 6mm dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer -in -charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coated of 20 microns over 5 microns primer coating to track coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J&L hooks,bolts and nuts 6mm dia and prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer- in- charge.

Painting two coats (excluding priming coat)on new steel andlayi1bijoother metal surfaces with enamel paint brushing to give and even shade includes cleaning the surfaces of all dirt ,dust andlayi1bevenother foreign matter with enamel white paint.

Providing and Fixing 27.5 centimetre long wire spring grade No.2 for rolling shutters

BIPAN KUMAR

RAKESH KUMAR

Gaurav Kumar

NITISH