GE(S)/M-47/2021-22

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not specifically provided for, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not specifically provided for, complete all as specified and directed. Note :-Reinforcement cut as required to facilitate demolition.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but not exc 4.00 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each and removing from site, complete all as specified and directed.

Dismantling timber scantling 40 Sqm and over in section in unframed work etc complete all as specified and directed.

Taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Racking out joints/poiting to masonry or brick work in single detached joints for flashing, etc complete all as specified and directed.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in benching, haunching, coping etc, including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for precast cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in kerbs mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregates) as surface channels and drains including demolition of existing drain complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick masonry (EXCEPT BRICKS) straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:4, complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick wall, built in CM 1:4, complete all as specified and directed.

S&F 40mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35mm thick factory made wire guazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats at site, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter (Wood garin colour sheets on both sides) 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing.

S&F Solid PVC door frame of size 75mm x 47mm, (suitable for moulded door) made out of 5mm thick wood grain printed PVC sheet & edges will be painted to match printed sheet as reinforced with 19mm MS Square tube, suppling & fixing in opening at site, complete all as per specifications & drawing.

S&F factory made 18mm (+ 0.7mm) thick PVC cupboard shutter, printed one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cbm finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's specifications.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised 30mm width of flaps (when open), complete all as specified and directed.

S&F ball catcher with proper magnetic effect fixed with shutter, complete all as specified and directed.

S&F 100mm size hasp and staple, aluminium anodised including bolts to hinge plate and fixed with screws.

S&F 100mm long butt hinges, medium weight, colled rolled mild steel (ISI Marked) complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 125mm long aluminium handle, cast type, anodised complete all as specified and directed.

S&F 100mm long aluminium handle, cast type, anodised complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, (ISI marked), complete all as specified and directed.

S&F 50mm dia polished hardwood knobs fixed with screws complete all as specified and directed.

S&F "as in repair" 25mm bore stainless steel powder coated drapery rod with 1.0mm thick including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.

S&F 300mm size mild steel, ordinary rat tail, rod pattern spring including roller and roller plate, complete all as specified and directed.

S&F aluminium (extruded aluminium section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight 60 to 80 Kg complete all as specified and directed.

S&F brass mortice lock 4-lever vertical type of 100mm size complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F "as in repair" stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F anodised powder coated (min. thickness of powder coating 50 micron) aluminium frame work for doors, window, ventilators, partition walls with one or more rebates including joining cleats for fixing etc, complete all as specified and directed.

S&F powder coated aluminium door shutter, aluminium section weighing not less than 0.75 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, 2 Nos handle in 150mm long in each door and two Nos 150mm long aluminium tower bolts in each shutter, SS hinges 125mm- 04 No, anonised aluminium snap beading, fixed with screws, complete all as specified and directed.

S&F 4mm thick aluminium composit panel for fixing to aluminium shutter and the like squares with aluminium beading band rubber gasket complete all as specified and directed.

S&F Box type steel windows and ventilators, comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube, factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes shall be measured and paid separately under respective items of BOQ) with steel handle and steel peg stay dovetailed or welded including 2 Nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to FI frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in PCC blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125mm x 60mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 105mm x 60mm for doors/windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F rolled mild steel framed work as in purlins, rafter, rails and fastenings and heavy brackets framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in ridge/valley , gutter or straight flashings etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

M&L for 40mm PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in floors laid in panels n. exc. 2.5 Sqm with top finished the surface even and smooth without using extra cement including glass dividing strips as per site requirement complete all as specified and directed

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in sub base of floors, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50 mm thick screened river washed sand cushion, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm but not exc 0.36 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed

M&L for 10mm thick vitrified ceramic 'light shade' colour tile (Square or Rectangular), polished, area of each tile not exc 0.36 Sqm (Joint free) as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 and finished rough, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 10mm thick vitrified ceramic 'light shade' colour tile (Square or Rectangular), polished, area of each tile not exc 0.36 Sqm (Joint free) as on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over and including 20mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in floors / cills etc, and moulding at edges if required including demolition of existing stone slabs and tiles any description or thickness complete all as specified and directed.

M&L for machine cut kota stone tiles as in riser of steps / pillars / skirting / dados 16mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding the edges of kota stone laid over and including 10mm thick rendering in CM 1:4 to recieve stone slab, including demolition of existing stone slabs and tiles any description or thickness complete all as specified and directed.

Cuting and polishing to existing kota stone flooring including repairing to joint & edge with grey cement and pigment and bee wax polishing complete all as specified and directed.

M&L for marble work (Green / Black marble Bhaislana Zebra) 18-20mm thick (table rubbed and polished) as in cooking plateform, window cills, jambs, steps and like over and including 15mm thick screed in CM 1:4 including pointing with white cement (1:2) using marble dust with admixture of pigment to match the marble shade including rounding the exposed edges full round, and making hole for gas pipe, complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 10mm thick rendering or plastering work in CM 1:3 on fascia or edging of chajjas, ceiling and roof projections etc. finished the surface even and smooth without using extra cement, complete all as specified and directed

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls including rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling including rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of washable distamper white or tinted complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distamper over a coat of chalk whitening primer, complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of cement base paint over a coat of alkali resistant primer including curing, before and after painting complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of Acrylic emulsion exterior paint over a coat of primer, complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, including hacking out old broken glass (any thickness, size, quality or description) from metal frames, glazed with putty or fixed with beads / clips,complete all as specified and directed.

S&F 4.8mm thick sheet glass, ordinary quality in square or rectangular covered with solar control film 25 micron reflective type sticked to glass pans fitted with aluminium beading and rubber gasket area exc. 0.5 Sqm in each pane complete all as specified and directed.

M&L for preparation of old surfaces of steel & iron work of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of newly surfaces of steel & iron work of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide zink primer complete all as specified and directed.

M&L for preparation of old surfaces of wood & wooden of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of newly surfaces of wood or wood based work of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of pink primer complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 1000 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 20mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 500 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position including 20mm dia PVC ball valve, high pressure with polythene float complete all as specified in SSR Part-1, including dismantling of existing PVC water tank of any capacity complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

M&L for 15mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Fixing only 15mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

M&L for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Fixing only 20mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in replacement 15mm bore chromium plated, fancy type angular stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F "as in repair" 20mm bore gun metal globe or gate valves, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F "as in repair" 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F "as in repair" 15mm bore Pillar tap, cast copper alloy, fancy type, with capston head, chromium plated, screwed down, high pressure with or without letters, hot or cold with long screwed shank and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F "as in repair" towel rail chromium plated brass 24'' size incl. fixing with SS screw and rawl plug complete all as specified and directed.

S&F in replacement PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F "as in repair" CP soap nich fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F "as in repair" Vitreous china wash basin, white flat back of size 550mm x 400mm including 32mm size CP waste coupling full thread and 32mm dia PVC waste pipe, brackets and cutting for and pinning in ends of brackets or errecting stand, complete all as specified and directed.

S&F "as in repair" vitreous china wash down water closet pan (pedestal pattern), white including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinging device including connections to drain or outgoing pipe and to flushing pipe anti syphonage pipe etc, complete all as specified and directed.

S&F "as in repair" PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.

S&F "as in repair" PVC ball valve, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed to 20mm bore pipe complete all as specified and directed.

S&F "as in repair" sink made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410mm x 330mm x 160mm including CP waste coupling and 32mm dia waste pipe including making disturbed surface to match with existing surfaces, complete all as specified and directed.

S&F "as in repair" sink with drainage board, made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 1200mmx460mm bowl size 410mm x 330mm x 160mm including CP waste coupling and 32mm dia waste pipe including making disturbed surface to match with existing surfaces, complete all as specified and directed.

S&F "as in repair" 75mm bore cast iron floor trap with stainless steel CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

M&L for Soakage well including excavation and earth work in any type of soil, foundation in PCC 1:4:8, walls of honey combed and solid in CM, RCC M-25 concrete, brick work in CM, RCC cover slab in M-25, RR masonary, filling with brick bats complete of size 3.00 m dia X 6.00 m deep all as specified and shown on drg TD Drg No CEPZ/C-TD/013/13 sheet 1/5 to 5/5.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for modular point wiring for one light/fan/bell point controlled by one switch complete with 1.5 Sqmm multistranded FR PVC insulated unsheathed fire retardent copper conductor cable 1100 volts grade in and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8mm including conduit accessories like bends, tees junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm single core FR PVC green insulated unsheathed multi stranded copper conductor 1100 Volts grade as earth continuity wire connected to earth dolly including inner and outer frame plate matching with surrouding with modular sunken steel boxes zinc oxide plated of suitable size including modular sheets of suitable module and back plates etc. complete all as specified and directed by Engineer-in-Charge.

Description all as per srl item No. 108.00 here-in-before but for 5 pin 5 amp socket outlet point on independent board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per srl item No. 108.00 here-in-before but for 5 pin 5 amp socket outlet point on same board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per Srl item No. 108.00 here-in before but for one 3/5 pin 15Amps socket outlet concealed using 2.5 Sqmm FR PVC insulated multi stranded copper conductor wire including 2.5 Sqmm FR PVC insulated unsheathed copper conductor earth wire and making good to disturbed surface of wall floor to match existing finishes etc complete all as specified and directed.

S&F modular socket outlet 6 Amp, 2/3 pin mutipurpose, 2 module complete all as specified and directed.

S&F modular socket outlet 5/15 Amp, 2/3 pin multi purpose, 2 module, complete all as specified and directed.

S&F modular switch 1 way 6 Amp, 1 module, complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

S&F lamp holder insulated body with back plate for batten fittings with polycarbonate body, including 9watt LED lamp complete all as specified and directed.

S&F ceiling rose surface bakelite 2 to 3 terminals 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F modular fan step regulator, step type suitable for 1200/1400mm sweep ceiling fan, hum free, 120W, 2 module, hum free and connecting electrically, complete all as specified and directed.

S&F modular bell push 1 way 6 Amp, 1 module, complete all as specified and directed.

S&F call bell ding dong type 230 Volts AC complete all as specified and directed.

M&L for submain wiring with two single core FR PVC insulated cable 2x6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked including 1x6 sqmm multistranded copper conductor FR PVC green insulated unsheathed cable for earth continuity, complete all as specified and directed. Note : Three runs of wire shall be measured as one unit.

S&F in replacement Recessed LED ceiling 36 Watt, luminaire of size 600mm x 600mm with white light window and built-in LED lamp with all accessories and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable and testing after fixing, complete all as specified and directed.

S&F surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F surface mounted 1x10 Watt LED tube light fittings (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F bulk head 10 Watt LED light fitting designed for modern homes available in non PIR as well as PIR sensor with premium quality diffuser for glarefree light aaaaand easy install snapfit installer 10 W LED 6000K complete with all acessories, connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm as required, complete all as specified and directed.

S&F in replacement of 20W LED Street Light luminaire, made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life. The luminaire shall be complete IP-65, AC 230 volts, for Optical Compartment and Control Gear Compartment.The Optical compartment shall be covered with heat resistant toughened glass for safety.The LED Street light should be top maintainable for easy maintenance.LED Street Light shall use multiple LEDs to get sufficient light output from the luminaire. The LED Street Light shall be of Integral type. The Input voltage range shall be 150V to 270V. The LED Driver shall be of isolated type with Constant Current Constant Voltage topology to ensure optimum driving of LEDs. The LED Street Light shall have power factor more than 0.95 complete all as specified and directed.

Note for srl item No 123 to 127 above 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

S&F in replacement of GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.

S&F "in replacement" VTPN distribution board with provision for MCCB as incommer 100A DD04 way IP 43 (for incoming MCCB & outgoing MCBs), with copper bus bar for each phase, with 2 Neutral bar, 2 Earth bar and cable ties for cable management, fully insulated bus bar & shrouded Neutral bars, with 100 Amps MCCB, 25 KA, 4 pole, as incommer and SP/TP MCBs as outgoing complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 12 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts with a two pin and earth plug and socket with one single pole MCB of 20 Amp, 240 volts complete fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F MCB single pole, 240 Volts, 6-32 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F MCB single pole and neutral, 240 Volts, 40 to 63 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F electric water heater storage type, of capacity 25 ltr, BEE 5 star rated and including taking out existing water heater of any type and size and depositing to MES store yard etc, complete all as specified and directed.

S&F ceiling fans with blade, down rods, electronic regulator and accessories 230volts, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) including making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning, and including taking out existing fan of any type and size and depositing to MES store yard etc, complete all as specified and directed.

S&F exhaust fans steel body with blade, frame, louvers and accessories 230volts, 450mm sweep, heavy dut,y five star rated including making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning and including taking out existing exhaust fan of any type and size and depositing to MES store yard etc, complete all as specified and directed.

Taking down ceiling/exhaust fan, sealing cable end, dismantling blades and removing fan and blades and refixing and hanging ceiling fan back after repair including fixing of blades, and diagnosing the fault/defect by replacement of old burnt fan winding with new copper wiring, and including electric connection overhauling including minor repairs by replacement of capasitor, safety pin, cap, nuts & bolts etc and making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

Taking down ceiling/exhaust fan, sealing cable end, dismantling blades and removing fan and blades and refixing and hanging ceiling fan back after repair including fixing of blades and including electric connectioin overhauling including minor repairs by replacement of capasitor, safety pin, cap, nuts & bolts etc and making connections using 3core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated , armoured heavy duty electric cable , with aluminium conductor of size 35 Sqmm x 3.5 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

Description all as per srl item No 140 here-in-before, but cable of size 16 Sqmm x 2 core complete all as specified and directed.

M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed

M&L for earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as required at site and directed.

M/s Rajeev Vashist

dadwal engineers

M/S HIMANSHU BUILDERS

M/S SEVENUP

VOHRA CONSTRUCTION CO

M/S RUDHRAKSH TRADING CO

M/s Ashoka Brothers

Bidder Name

dadwal engineers

M/S RUDHRAKSH TRADING CO

AV ENTERPRISES

M/s Ashoka Brothers

M/S SEVENUP

M/s Rajeev Vashist

M/S HIMANSHU BUILDERS

VOHRA CONSTRUCTION CO