SPL REPAIRS TO RAMPART 1, 4 AND 6 AND PROVN OF WOODEN PANELLING AT CONFERENCE ROOM AND SIG BR CORRIDOR AREA TO COVER OPEN WIRING AND CONNECTED SERVICES, ADDN/ALTN OF OFFRS OFFICES AND IMPROVEMENT TO FLOORING WITH CONNECTED WORKS IN OFFICE AREA AT

Amount

SCHEDULE 'A' PART-I (B/R WORKS) Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 150 mm thickness (above or below groud level) complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description as in roofs, floors or beams, staircases, landings, chajjas and similar suspanded works etc., and in any position, complete all as specified and directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all quaries, arches pillars etc and removing debris off the site complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Dismantling structural steel work of any description including doors, gates, railing etc but excluding framed trusses complete all as specified and directed.

Taking down shutters of any description area exc 1.00 sqm but not exc 2.0 sqm each and removing from the site complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) area not exceeding 1.5 Sqm each and removing from the site complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) area exceeding 1.5 sqm and not exceeding 4 sqm each and removing from the site complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting any gauge or any thickness in roof covering including stacking serviceable materials of re-use and removing unserviceable materials complete all as specified and directed.

Dismantling of ceiling board incl snap grid frame of any thickness including cover fillets complete all as specified and directed.

Dismantling of wall board as in lining, panelling etc, of any gauge or any thickness including cover fillets complete all as specified and directed.

Cutting holes in to brick wall for inserting bold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, depth exceeding half brick but not exceeding 1 brick complete all as specified and directed.

M&L for brickwork with fly-ash old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M& L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L Rendering 15mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:3 to concrete surfaces ceilings, finished even and smooth without using extra cement complete all as specified and as directed.

M&L 100mm PCC (1:2:4) type B-2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L 40mm PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in floors as sub base, finished the surface even and rough to receive top layer, complete all as specified and directed.

M&L Vitrified ceramic coloured (light shade) digital tiles, double charged, minimum 08 mm thick (square/ rectangular) polished, area of each tiles exc 0.42 sqm but not exc 1.28 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and incl 15mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and as directed

All as per item No. 20.00 above, but light coloured double charged vitrified digital tiles as in skirting, fixed over and incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L Non Skid joint free coloured digital tiles, minimum 7 mm thick, area of each tiles exc 0.11 Sqm but n.exc 0.18 Sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as a specified and as directed

M&L Non Skid joint free coloured digital tiles, minimum 7 mm thick, area of each tiles exc 0.06 sqm but n.exc 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and incl 15mm thick screed bedding in cement mortar 1:4 complete all as a specified and as directed

S&F Glazed decorative coloured ceramic tiles in vertical surface, size 300 X 450 X 7 mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F 18-20 mm thick Granite slab, as in floors etc, machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pavement to match the shade of granite stone incl grinding and polishing over and including 20mm screed bed in cement mortar (1:6) complete all as specified and directed.

S&F 18-20 mm thick Granite slab as in vertical surfaces machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pavement to match the shade of granite stone incl grinding and polishing over and including 10mm rendering in cement mortar (1:3) complete all as specified and directed.

M&L for RCC (1:1½:3), type A-1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams, columns in floors, roofs, landings, balcones, canopies, duck slabs, shelves and like etc., (upto 4th Story Bldg) complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for fair finished surfaces (upto 4th Story Bldg) complete all as specified and directed.

M&L for mild steel TMT Bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm or securing with clips, etc., complete all as specified and as directed.

S&F rectangular and curved factory made uPVC fixed windows with frame dimension of 58mm x 52mm x 33mm for windows with corners fusion welded, fully reinforced with Galvanized steel of 1.2mm . The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weatherability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should have extrusion facility in India and the windows to be assembled and installed by an authorised local fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets,bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and also scaffolding if required for fixing is deemed to include in the rate quoted complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

S&F factory made uPVC- Sliding windows/doors having three tracks and three sashes (shutters) with frame dimension of 104mm x 49mm and sash dimension of 61mm x 47mm x 37mm each with middle sash fixed ,fixing of powder coated grill with and including upvc beading of required size, with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm. The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weatherability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in 1st quality (including EPDM gaskets,bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles having a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and poweder coated aluminium grill and includes all other connected accessories. Net opening will be measured for payment purpose.Glass and poweder coated aluminium grill will be measured and paid separately under respective items)

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: Stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 100 mm size stainless steel butt hinges complete all as specified and directed. (Make: PRAYAG, Cat No: HG-2414 or any other reputed make as approved by GE)

S&F stainless steel handle 200 mm long complete all as specified and as directed. (Make: PRAYAG, Cat No: DHL-2200 or any other reputed make as approved by GE)

S&F Stainless steel tower bolt 200 mm long complete all as specified and as directed. (Make: PRAYAG, Cat No: TBR-2200 or any other reputed make as approved by GE)

S&F 300mm long stainless steel sliding bolt with hasp, staple (bolt type) and fixing clips complete all as specified and directed. (Make: PRAYAG, Cat No: LD-1212 or any other reputed make as approved by GE)

S&F Floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor, overal length of cover plate 150 mm complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, aluminium (die cast) body, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixedcomplete all as specified and directed.

Taking down, easing and adjusting aluminium shutters / partitions including rubber beading complete, of any description, area exc 1 sqm but not exc 2 sqm each and refixing in same position after necessary repair, replacement of defective accessories complete all as specified and directed. (NOTE: Builder's hardware, if replaced, shall be measured and paid seperely)

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F 4.8 mm thick frosted sheet glass ordinary quality and glazing in square exc 0.50 Sqm in each pane complete all as specified and directed.

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for Mild steel works conforming to Fe-290 Gde E-165, framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc complete all as specified and directed.

M&L Preparation of old decorated surfaces of Walls (by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss, efflorescent salts, trading oils and greasy spots) and applying one coat of white wash, complete all as specified and as directed.

All as per item No.44.00 above, but One coat of white wash on Ceilongs

M&L complete removal of existing treatment on walls and applying two coats of oil emulsion distemper over a coat of alkali resistant primer by brush and finished with rollers and applied over and including 2 mm thick wall putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of acrylic bound distemper with rollers over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying 2 mm thick wall putty duly finished to a smooth surface and applying two coats of acrylic bound distemper with rollers over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls (by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss, efflorescent salts, trading oils and greasy spots) and applying one coat of acrylic distemper by brush and finished with roller complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls (by brooming down or steel wire brushing, scrapping down smoke soots, moulds, moss, efflorescent salts, trading oils and greasy spots) and applying Two coats of acrylic distemper by brush and finished with roller complete all as specified and directed.

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

S&F Suspended metal grid Ceiling System with mineral fibre acoustic tiles as per following specifications:- a) Ceiling Tiles:- Mineral fibre acoustic tile of 16mm thickness having sand textured finish with acoustical punchers, bevelled tegular edge and 8mm drop in module size of 600 x 600mm. Tiles shall have humidity reistance (RH) of 99%, NRC 0.50 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84. b) Metal Grid:- The grid system shall be 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. The ceiling grid sections shall be fixed to ceiling with 6 mm dia GI hangers upto required length by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long. (MAKE OF CEILING GRID : ARMSTRONG, Model: SUPRAFINE 38 or equivalent in GYPROC / USG BORAL / UNISTEEL MAKE OF CEILING TILES: ARMSTRONG, Model: DUNE or equivalent item in GYPROC / USG BORAL / U TONE)

M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

S&F PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed.

S&F 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

S&F Stainless steel round grating 102mm dia as in repairs, complete all as specified and directed. (Make : PRAYAG, Cat No: FT-62 or equivalent make as approved by GE)

S&F Chromium plated Hand shower (health faucet), brass body with 1.2 metre long flexible tube in chrome finish with wall hook, as in repairs, complete all as specified and directed. (MAKE : JAQUAR, Cat No : ALD-573/ PARRYWARE, Cat No : T9941A1 / ESS ESS, Cat No: C-232D / CERA, Cat No: F8030301 / HINDWARE, Cat No: F160002)

S&F Chromium plated brass Angular stop cock, fancy type, concealed type with wall flange fixed to 15 mm bore of Iron pipe, as in repairs, complete all as specified and directed. (Make : JAQUAR, Cat No: CON-59KN / PARRYWARE, Cat No: G1453A1 / CERA, Model: OCEAN / PRAYAG, Cat No: 9210 / HINDWARE, Cat No: F330043)

S&F in repair Chromium plated brass Bib cock with wall flange, fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: CON-107KN/ PARRYWARE, Cat No: G1405A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9208 /HINDWARE, Cat No: F330041)

S&F 15mm bore chromium plated two way bib cock with flange (premium quality), fancy type, as in repairs, complete all as specified and as directed. (Make : JAQUAR, Cat No: FUS-29041 / CERA, Cat No: F1015163/ ASIAN PAINTS, Cat No: ALBC102 / PRAYAG, Cat No: 9311-N/HINDWARE, CAT No: F360005 or equivalent model in PARRYWARE, Cat No: G4834A1)

S&F Chromium plated brass Wall mixer, concealed type incl concealed body, with both overhead and telephone shower arrangement, fixed with 15 mm bore Iron pipe including taking down existing mixer complete all as specified and directed. (Make : Jaquar, Cat No : CON-281KN / PARRYWARE, Cat No: G1417A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9280 / HINDWARE, Cat No: F200022) NOTE: Telephone shower shall be measured and paid seperately.

S&F Towel rail (premium quality) 20mm dia, 600mm long between flanges, including taking down existing rack, complete all as specified and directed. (Make : JAQUAR, Cat No: ACN-111SM / ESS ESS, Cat No: AC-101 / PARRYWARE, Cat No: T6401A1 / CERA, Cat No: F5004103 / PRAYAG, Cat No: BA-20)

S&F Chromium plated brass Towel ring (premium quality), as in repairs, complete all as specified and directed. (Make : Ess-Ess, Cat No: AC-502 / JAQUAR, Cat No: ACN-1121BN / PARRRYWARE, Cat No: T6002A1 / PRAYAG, Cat No: BA-11 )

S&F Towel rack (premium quality) with lower hangar with hook, incl taking down existing rack complete all as specified and directed. (Make : JAQUAR, Cat No: AHS-1581H / ESS ESS, Cat No: AC-308 / PARRYWARE, Cat No: T6008A1 / CERA, Cat No: F5003101 / PRAYAG, Cat No: BA-12)

S&F Toilet paper holder, surface type with flap, incl taking down existing holder complete all as specified and directed. (Make : JAQUAR, Cat No : ACN-1153N / CERA, Cat No: F5007110 / PRAYAG, Cat No: BA-38 / ESS ESS, Cat No: AC-506 / HINDWARE, Cat No: F880003 / PARRYWARE, Cat No: T6514A1)

S&F Aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, as in repairs, complete all as specified and directed.

S&F Vitreous china floor mounted coupled closet (Pedestal pattern), white, including low level vitreous china valveless symphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC white soft close seat cover and connecting fittings, as in repairs, complete all as specified and directed. (Make :CERA, Model : CLAIR / PARRYWARE, Model: CASCADE NXT / JAQUAR, Model: FLORENTINE / HINDWARE, Model: CONSTELLATION)

S&F fancy type chromium plated telephonic hand shower with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed. (Make : PARRYWARE, Cat No: T9983A1/ PRAYAG, cat No: BHS-91S / CERA, Cat No: F7030502 / HINDWARE, Cat No: F160053 or equivalent model in JAQUAR)

S&FVitreous china, white, counter top wash hand basin, including providing 32 mm dia chromium plated waste coupling and waste pipe and making all necessary connections, as in repairs, complete all as specified and directed. (Make : Hindware, Cat No: 10038 / CERA, Cat No: S2030101 / Parryware, Cat No: C0431 or similar model in JAQUAR)

S&F in repair 15mm bore chromium plated central hole basin mixer (premium quality) without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. (MAKE : JAQUAR, Cat No : CON-167KNB / PARRYWARE, Cat No: G1414A1 / CERA, Model: OCEAN / PRAYAG, Cat No: 9250 / HINDWARE, Model: CONTESSA PLUS)

S&F Chromium plated brass over head shower rose with arm (premium quality), with 3 flow, fixed to 15mm bore of iron pipe, as in repairs, complete all as specified and directed. (Make : CERA, Cat No: F7040103 (for arm) & F7020305 (for shower) / PARRYWARE, Cat No: T9802A1 (for arm) & T9986A1 (for shower)/ HINDWARE, Cat No: F160051 / PRAYAG, Cat No: BOS-86)

S&F15mm bore chromium plated two way bib cock with flange, fancy type, as in repairs, complete all as specified and as directed. (Make : JAQUAR, Cat No: CON-041KN/ PARRYWARE, Cat No: G1434A1 / CERA, Model : OCEAN / PRAYAG, Cat No: 9212/HINDWARE, CAT No: F330004CP)

S&F 6mm thick bevelled edge mirror of size as required fixed on 6mm thick acrylic PVC sheet, as in repairs, complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plug washers, waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 914 mm x 460 mm and bowl size 405 mm x 354 mm x 203 mm complete including taking down existing sink complete all as specified and directed. (MAKE : PRAYAG, Cat No. 1239-D or equivalent model in NIRALI / DIAMOND / ANJALI / JAYNA / BLUE STAR / CERA / PARRYWARE)

S&F in repairs Stainless steel kitchen rack of size 31" x 24" x 10" fixed in wall with screws and washer complete all as specified. (Make- Prayag , Model No- P-340 or equivalent model in SUYOG / BLUE STAR / ANUPAM INDUSTRIES)

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, as in repairs, complete all as specified and directed. (Make: Ess-Ess:Cat No.AC207 or equivalent make specified in particular specifications)

S&F Corner glass shelf 300 mm with brass brackets, as in repair complete all as specified and directed. (Make: PRAYAG, Cat No: BEA-44 / JAQUAR, Cat No: ACN-1173 / PARRYWARE, Cat No: T6010A1 / CERA, Cat No: F5005102/ ESS ESS, Cat No: AC-207A)

S&F 600mm x 600 mm mirror with PVC frame and fixed to wooden plugs with cromium plated brass screw and cup washers, as in repairs, complete all as specified and directed. (Make: PRAYAG, Cat No: 553 or equivalent model in other makes specified in CA)

S&F Low density polyethylene pipe connection, comprising of 15 mm dia 450 mm long having PTMT union at each end of connection to each of pillar tap/cistern/stop cock/urinal etc. at one end, stop cock at other end, as in repairs, complete all as specified and directed. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 or equivalent model in SHAKTI / JEXON)

S&F Mono block water pressure pump set of 0.50 HP capacity, single phase, discharge range 36-60 LPM, working in voltage range 220-240 V, with operating pressure range 1.4-2.4 (Bar), complete including with closed discharge valve and connected fittings, as in repairs, complete all as specified and directed. (MAKE : KIRLOSKAR-ETERNA Model. SJPBS 42420-HL or equivalent as approved by GE)

S&F decorative type stainless steel powder coated curtain rod, 25 mm dia, double curtain fitting type, fixed with end brackets complete all as specified and directed. (NOTE: Brackets will be measured and paid seperately)

S&F decorative type brass brackets for curtain rod, suitable for double curtain complete all as specified and directed.

Taking up or down steel water tubing 15 mm bore incl connections etc complete all as specified and directed.

All as per item No. 84.00 here-in-before but 20 mm bore

S&F tubes 15mm bore "medium grade" galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

All as per item No. 86.00 here-in-before but 20 mm bore

S&F for 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, moulded or chamfered, put together with glue, pinned at joints complete all as directed.

M&L mild steel bands and straps support or stays holdfast and similar articles conforming complete all as specified and directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

M&L for anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc complete all as specified and directed.(NOTE: Glass shall be measured and paid seperately)

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as suitable 150 mm long peg stays (01 No), hinges type B-21 100 mm long (02 Nos), suitable handle-01No each shutter etc as per manufactures instruction complete all as specified and directed. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle etc as described in item. Sheet glass shall be measured seperately)

S&F in repair powder coated aluminium wndow grill of size 100 mm X 100 mm having section width 6 mm and 3 mm thickness, fixed on aluminium section weighing not less than 0.55 kg/sqm including necessary jointing, fitting etc all as per manufacturer's instruction complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, width of flaps (when open) 30 mm complete all as specified and directed.

S&F 12mm thick plywood grade BWR type B-B, fixed with screws to timber frame-work (as in cup board etc) complete all as specified and as directed.

S&F Block boards 18 to 19 mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber frame-work (as in cup board etc) complete all as specified and as directed.

S&F 0.90 mm thick laminate type-1(sunmica) of surface finish colour and pattern as approved, fixed to ply wood or blockboard with suitable adhesive as per manufacturer instructions, complete all as specified and directed.

S&F 4.8 mm thick plain sheet glass frosted on one side and area in squares exc 0.50 Sqm in each pane and glazing with rubber gasket fixed to aluminium frame work/snap beading, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for preparing new surface of wood or wood based material of any description and in any position not otherwise described for, exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of wood primer complete all as directed.

Supply & fixing 100mm stainless steel butt hinges (medium weight) cold rolled complete all as specified and directed.

S&F floor door stopper of brass body and tounge, anodised, with hard drawn steel spring, fixed in floor. 150mm overall length of cover plate complete all as specified and as directed

S&F 600mm long brass skeleton tower bolt of extruded section with cast brass plate and staples and rolled or drawn brass bolts and fixed, complete all as specified and as directed

S&F 125mm long extruded brass handles, fabricated type, polished, complete all as specified and as directed

S&F 250mm long Brass sliding door bolt with sand or die-cast brass hasp staple (blt type) and fxing bolt with rolled or drawn brass brass bolts, complete all as specified and as directed

S&F 40mm dia cup board knobs fancy type (as approved by GE), complete all as specified and as directed

S&F Mild steel barrel tower bolt 75mm long, stov enamelled black, with bright bolt and fixed, complete all as specified and as directed

S&F 4 levers brass body lock, drawer gradd 1 size 50mm, complete all as specified and as directed

S&F Alunimium 'E' channel for sliding drawer shutter of cub board in two way 300mm long, complete all as specified and as directed

S&F 100mm double action spring hinges (hydraulic hinges) brass with phosphors bronze wire spring, bright polished, complete all as specified and as directed

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap as in roof, walls, fixed with L-type or J-type or crancked hook bolts in lieu of screws, complete all as specified and as directed

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

Supply and fixing Rolled mild steel in joist, channel, angle, or tee section fixed independently, upto a height of 6 metre from each floor level (cut to ordinary length i.e. within 20mm of the length indicated) of FE-410- W(Gde-E-250) quality-A including using iron props and steel plates to existing RCC overhead members like beams, slabs etc so as to ensure safety of existing structure and floor during repairing works complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of Red oxide, zinc chrome primer to new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer-in-Charge.

S&F Welded steel wire fabric, weight not exc 4 kg/sqm, fixed to wood or steel members complete all as specified and directed.

SCHEDULE 'A' PART-II (ELECTRIFICATION WORKS) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants, regulators, sockets, light fitting etc for reuse or removing from site and making good disturbed surface of walls, floors etc. complete all as specified and directed.

Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.

Taking down of old Submain wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly,.complete all as specified and directed. for one light point / bell point/ceiling fan/exhaust fan point controlled by one way switch. (NOTE :- (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Point wiring shall be measured from switch board/DB to outlets only. Main circuit wire of the switch board/DB shall be measured and paid seperately as sub main wiring of required size depending upon the load of that switch board. (iii) Quoted rate shall be exclusive of the cost of terminal box and laminate cover which shall be measured seperately.

All as per item No 122.00 here-in-before but for one 5 pin 5/6 amp socket out let point in the same switch board of light points (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No122.00 here-in-before but for one 5 pin 5/6 amps multisocket outlet point in independent board (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 122.00 above but using 2.5 sqmm PVC insulated unsheathed multi strand copper cable (1100 V) FRLSH for line conductor and 1.5 Sqmm PVC insulated unsheathed multi strand FRLSH copper cable (1100 Volts) for earth continuty wire for one 15/16 amp multi socket out let independent (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

Refixing of point wiring obtained from item No. 125.00 with existing 1.5 sqmm PVC insulated stranded copper conductor single core for both mains and earth wire laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. Note:- Cost of cutting chases on walls / ceiling and making good disturbed surfaces including finishing with cement mortar (1:3) etc; and screws nut and bolts required for fixing shall be deemed to be included in the rate quoted above.

All as per item No. 126.00 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 127.00 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 128.00 above but using 2.5 sqmm single core multi stranded copper conductor for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

S&F Modular Switch 1 way, 6 Amps, 1 module complete all as specified and directed.

S&F Modular Switch 1 way, 16 Amps, 1 module complete all as specified and directed.

S&F Modular Socket 6 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S&F Modular Socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S&F Modular Fan step regulator, 120 watt, 2 module complete all as specified and directed.

S&F Modular Bell push 6 Amps, 1 module complete all as specified and directed.

S&F Modular Blank plate, 1 module complete all as specified and directed.

S&F Modular White cover plate with frame 3 module complete all as specified and directed.

S&F Modular White cover plate with frame 4 module complete all as specified and directed.

S&F Modular White cover plate with frame 6 module complete all as specified and directed.

S&F Modular White cover plate with frame 8 module complete all as specified and directed.

S&F Modular White cover plate with frame 12 module complete all as specified and directed.

S&F Modular type Metal Flush box 3 module complete all as specified and directed.

S&F Modular type Metal Flush box 4 module complete all as specified and directed.

S&F Modular type Metal Flush box 6 module complete all as specified and directed.

S&F Modular type Metal Flush box 8 module complete all as specified and directed.

S&F Modular type Metal Flush box 12 module complete all as specified and directed.

S&F new Call bell, musical type, AC 230/240 Volts, single pole complete all as specified and directed.

S&F ceiling rose surface, polycarbonate/bakelite, three terminals complete all as specified and directed.

M&L for sub main wiring with four run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 Sqmm alongwith one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 10.0 Sqmm as earth continuity conductor drawn through and including PVC conduit of suitable size, surface type incl taking down existing wiring complete all as specified and directed. (NOTE : Three runs of single core 6.0 sqmm cable & one run of PVC conduit shall be measured as one unit)

All as per item No.149.00 above, but two run of 6.0 Sqmm cable with one run of 6.00 Sqmm as cable earth continuity conductor.

All as per item No. 150.00 above, but two run of 4.0 Sqmm cable with one run of 4.00 Sqmmas earth continuity conductor.

Material and labour for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth complete all as specified and directed.

Supply and Fix in repairs recess mounted LED luminaire, of size 600 mm x 600 mm, in powder coated CRCA housing , having glare free diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 35/36 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size, complete all as specified and directed and complying with the following specifications:- (a) minimum efficacy 110 lumen/watt (b) CRI not less than 80, (c) THD < 20% (c) having in built short circuit and surge protection (d) colour temperature not less than 5700 degree K (e) life not less than 25000 hours of operation (f) Weather protection: IP20

S&F LED decoratie wall light fitting 4W x 2, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable 2 LT wall lamp Opal Glass with Chrome Finish Lamp E-14 LED 4w x 2 complete all as specified and directed. Make:- Jaguar Cat Part No. KCH-CH-MB160275532B or equivalent make in Havells/Bajaj/Philips

Fixing only LED lights fitting any type with driver, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Re-fixing of recess mounted LED luminaire suitable for 600 x 600 mm snap grid ceiling, any wattagecomplete with all accessories with and including 36 Watt LED of lumen efficacy 110 lumen/watt and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed.

Taking down carefully serviceable ceiling/wall mounted fans/exhaust fans, any size, sealing cable end, dismantling blades and keeping in safe custody and re-fixing in existing or new location, connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 1.0 Sq mm, 3 core, 1100 Volts grade, from ceiling rose/ connector to fan complete all as specified and directed.

S&F down rod of 15 mm dia of galvanised steel tubing, medium grade duly painted with one coat of primer and two coats of synthetic enamel paint, of length as per site requrement complete all as specified and directed.

S&F DB, VTPN, 4 way, vertical type, IP 43 protection, double door (premium range), 415 volts with provision for MCCB as incomer and MCB as outgoing and electrically connecting up complete all as specified and directed. (MAKE : L&T, Cat No. DBVTH004DD /LEGRAND, Cat No: 5077 45 / ABB, Cat No: E-SVTDB M 4XT3 /HAGER, Cat No: VYV04DM2-P /SCHNEIDER, Cat No: A9HVD04L)

S&F TPN DB, IP 43 protection, double door (premium quality), 415 volts, 4 way (8+12), with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)

Supply and Fix, Double Door, Sheet Metal Enclosure for DBs (Premium Quality), for mounting of MCB for 240 Volts, SPN 8 way, with 100 Amps rated copper bus bar, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)

S&F SPN DB, IP 43 protection, double door (Premium Quality), 240 volts, SPN 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D)

NOTE FOR ITEM NO.159 to 162 :- (1) Incoming MCCB/RCCB/MCB and outgoing MCBs shall be measured and paid seperately as "Supply Only". (2) Quoted rate is deemed to be inclusive of blanking plate for slots remaining blank after fixing of MCBs. (3) DB, MCCB, RCCB & MCB shall be of the same manufacturer.

S&F MCB (premium quality), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium quality), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (Premium Quality), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCCB (premium range), 4 pole, 100 Amps, 16 kA, 415 Volts, AC, 50 Hz with and including adjustable thermal and magnetic setting, fixed in DB complete all as specified and directed. (MAKE : L&T, Cat No: CM90518OOKO / LEGRAND, Cat No: 420015 / HAGER, Cat No: HDA101U or equivalent model in SCHNEIDER, Cat No: LV426167 /ABB, Cat No: 1SDA066818R1)

S&F in repair MODULAR MCB protected power unit with one 25 Amps socket with 3 pin plug top and including 01 No MCB, DP, and starter 25 Amps ratings with six module plate and flush metal GI box and electrically connected complete all as specified and directed. (MAKE : HAVELLS, Cat No. DHDUCDP0253025 / NORTH WEST, Cat No: ACPU6M-BT or equivalent model in ABB / CRABTREE / HAGER / SCHNEIDER / LEGRAND) (NOTE : Enclosure & MCB shall be same manufacturer. Cost of MCB is deemed to be included in the quoted rate)

Re-fixing of SPN DB any type in existing or new position incl necessary connections comple all as specified and directed

Re-fixing of MCB, SPN any capacity complete all as specified and directed

Re-fixing of MCB, SP any capacity complete all as specified and directed

SCHEDULE 'A' PART-III (AC WORKS) Supply, installing and testing split type inverter AC, with indoor & outdoor unit complete, single phase 230V, Copper Condenser with cordless remote control with minimum 5 star rating of capacity 2.0 TR including 4 sqmm 3 core flex cable connection from indoor to outdoor unit as per site requirement including necessary masonry work for making good distrubuted surface and match with the existing colour complete all as specified and directed. (MAKE: DAIKIN, Model No: JTKJ Series / CARRIER, Model No: DURAFRESH NEO-X or equivalent model in HITACHI / O-GENERAL) NOTES:- 1. AC refrigerant should be Non CFC. 2. Brackets for installation of outdoor unit shall be measured and paid seperately) 2. Copper pipes beyond the standard length supplied by manufacturer alongwith the ACs shall be measured and paid seperately)

Supply and laying refrigerant line copper tubing of size 1/2" with clamping on wall surface or concealed with both the ends connection complete all as specified and directed. [Note: Cutting chases and making good of distrubuted surfaces will be measured and paid under seperate item ]

All as per item Ser No 173.00 here - in - before but of size 1/4 "

S&F foam insulation for copper tubing dia 1/2'' and 1/4'' complete all as specified and directed.

S&F drain pipe 5/8" dia PVC jacketed heavy duty with fixing of clamp complete all as specified and directed.

S&F powder coated MS bracket stand (1 pair set ) for supporting of outdoor units complete all as specified and directed.

S&F in repair PVC cable tray of size 100 X 100 mm, 16 gauge thickness with all accessories such as clamps, screws etc complete all as specified and directed.

S&F in repair PVC flexible pipe of size 100 mm dia with all accessories such as clamps, screws etc for covering of copper pipes outside the wall complete all as specified and directed.

Supply and draw wiring with one 4 core 4.0 sqmm PVC insulated copper cable 1100 volts grade multi stranded from indoor to outdoor unit duly connected with copper lugs suitable at site complete all as specified and directed.

PRABIR TRADERS

dutta and dutta

UNITED ENGINEERS

MS HORIZEN

GHOSH ENTERPRISE

JOY RAM ENTERPRISE

BASU AND CO