PROVISION OF TEMPORARY OVER HEAD SHED FOR DG SETS AT LAXMIPUR UNDER GE (S) DIGLIPUR

Amount

Surface dressing not exceeding 15 cm deep in soft/ loose soil surface formed to required slope etc, complete all as specified and as directed

Excavating in trenches not exceeding 1.5 mtr wide and not exceeding1.5 mtr deep and getting out any type soil complete all as specified and as directed

M&L for PCC (1:3:6) Type C2 (using 40mm graded granite stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for pre-cast cement concrete (1:3:6) Type C1 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks with minimum compressive strength of 50 Kg/Sqcm, exceeding 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4), finished even and smooth without using extra cement complete all as specified and directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for Hardcore of gauge not exceeding 63 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface broken stone or boulders complete all as specified and directed.

M&L for 100 mm thick PCC (1:4:8) Type D2 (using 40 mm graded crushed granite stone aggregate) laid in sub-floors, sub-bases, floors and pavings, etc. finishing surfaces of concrete even and rough complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete (1:2:4) type B1 (20mm graded stone aggregate) finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for forming 20 mm thick & 150mm deep expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exc 0.5 cum, getting out in hard/dense soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and watering and removing surplus soil to a distance not exc 50m and making good the surfaces complete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) in foundation, filling and mass concrete complete all as specified and directed.

M & L for plain cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) as in foundations, filling and mass concrete for fixing of post holes complete all as specified and directed.

S&F Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and with revited bolted or welded attachment Fe-410- W(Gde-E-250) quality-A complete all as specified and as directed.

S&F Rolled mild steel work in tubular trusses including special shaped washer etc. complete using ERW or including butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick Grade AZ 150 GSM of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, as per manufacturer instructions complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick Grade AZ 150 GSM of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws, as per manufacturer instructions complete all as specified and as directed.

M & L for preparation of new or previously untreated steel surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F mild steel flat iron 40x3mm as in valley gutter and wind tie and similar work including securing bolt and necessary drilling work conforming to Fe 290 Gde-165 complete all as specified and directed.

M&L for mild steel screw bolts of up to 75mm long and 12mm dia of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.

City Constructie Pvt Ltd (BID ID -3137633)

M/s Sharma Trading Company (BID ID -3135966)

SUMAN (BID ID -3140810)