SPL REPAIR TO COOK HOUSE AT BLDG NO T-05 AND P-13 INCLUDING PROVN OF CHAIN LINK FENCE POLE AT QUARTER GUARD AND SINGLE JCO LIVING ACCN AT ASC BN AND SPL REPAIR OF TOILET AND BATHROOM (06 NOS) IN BLDG NO P-01 AT EME BN UNDER GE (NORTH) AKHNOOR

Amount

Sunken Floor treatment :- Providing and laying of water proofing treatment to sunken portion including vertical portion by applying cement slurry mixed with acrylic based polymer modified cementitious composite compound of make as specified and approved including demolition and filling of sunken floor with & including PCC 1:5:10 type E-2 (using 40mm brick aggregate). (a) First layer of slurry of cement @0.488 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.253 Kg/Sqm. This layer allowed to air cure for 4 Hours. (b) Second layer of slurry of cement @0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.125 Kg/Sqm. This layer allowed to air cure for 4 Hours. (c) 15mm thick plaster in CM 1:3 mixed with WP compound to be provided while concrete is still green. (d) Joint of/Trap/WC/Soil pipes shall be properly sealed with sealing compound. Note:(a) Concrete for sunken slabs shall be mixed with WP compounds as per manufacturer's instructions. Before carrying out water proofing treatment the sunken slab shall be tested with water for 48 hours for any leakage /dampness is seen in ceiling below, then treatment is again carried out to RCC slab and it is again tested before passing for next stage. (The rate quoted includes water proofing compound as per manufacturers instructions). (b) Please note that only floor area shall be measured for payment purpose.

Demolition / taking down of existing old tarfelt , water proofing membrane, water proofing plaster of any description any type over RCC roof including any roof tiles, cement mortar screed, concrete screed of any thickness, for fixing of angle iron for water tank postion, incuding making good the surface by concrete to smooth surface complete all as specified and as directed.

Rendering 15mm thick cement plaster with cement mortar(1:3) with water proofing compound on fair finishes of brick work or concrete surface of roof slab, to be finished even and smooth(without using extra lime or cement ) all as specified and directed.( Water proof compound rate is not paid seperatly.)

Roof treatment :- Water proofing treatment to RCC roof slab including parapet as under :- (a) Ist Course : Apply a coat of bituminous primer conforming to IS-3384@ 0.40 Kg /Sqm on prepared surface of plaster and after drying of primer, apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm on plastered surfaces. (b) 2nd Course : APP (Atactic Polypropylene) modified polymeric membrane, 5 layered, 3 mm thick weight not less than 3.0 Kg/Sqm with 150 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 150 mm end overlap, membrane has to be laid with LPG torch and overlap sealed and finished neat, all joints. (c) 3rd Course : Apply a coat of hot blown 85/25 grade bitumen conforming to IS-702 @ 1.2 Kg/sqm over membrane and dusted with dry sand @ 0.50 to 1 Kg/sqm. (i) On Non-accesible roof : After providing (a) to (c) provide aluminium paint as per manufacturer instructions. (ii) Coved fillet in PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of required radius 75mm shall be provided at the junction of roof and vertical surface such as parapet wall/mumty around opening and treatment mentioned above shall be applied followed by a cement plaster 20mm thick in cement mortar(1:6). Note : (i) Roof treatment work shall be carried out through approved manufacturers only or through their authorised personal only.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Rendering 15mm thick cement plaster with cement mortar(1:4) on fair faces of brick work or concrete surfaces and finished the surface even and smooth without using extra cement, complete all as specified.

Rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5mm thick cement plaster with cement mortar(1:3) on concrete surface as in ceiling finished even and smooth without using extra cement, complete all as specified and as directed.

Supply only Integral water proofing compound.

Preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whitening primer complete all as specified and as directed.

Preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete, all as specified and directed.

Preparation of newly plastered surfaces of ceiling and apply three coat of white wash, complete all as speicfied and directed.

Complete removal of existing treatment incl washing, rubbing down and stopping of old painted surfaces and applying two coats of cement base paint to walls complete all as specified and as directed.

Preparation of old plastered surfaces of walls and applying two coats of oil bound distemper over one coat of 2mm putty after complete removal of existing surfaces of any layer complete all as specified and as directed.

Preparation of old decorated surface including washing,scrubbing down and stopping of painted surfaces and apply two coats of white wash on ceiling, complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) as in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

25mm thick cement concrete 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregates) as in floor sub bases and finished even and rough to receive topping layer complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness laid bedded and pointed in any mortar in floors, aprons etc. complete all as specified and directed

Granite (of any type) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and like including pointing in white cement (1:2) using marble dust with admixure of pigment to match with shade of granite including 10mm thick screed of CM 1:4 after applying cement slurry@3 kg/sqm of cement per sqm, complete all as specified. (Note : A hole shall be drilled in the Granite after fixing for gas pipe all as directed by Engr-in-Charge).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with & including 15 mm thick screed bed in cement and sand mortar 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles (350x250mm)/ (450x350mm) x 7mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in CM 1:4 on other than fair faces of brick work finished even and fair to receive tiles, complete all as specified and directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 Sqm and n.exc 4.00 Sqm each complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each, complete all as specified and directed

Steel windows/ventilator (Box type) factory made with double shutter with or without devetailed bar ( gauzed & glazed shutter) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts in each shutter 100mm long with & including 8mm square bar grills, complete all as specified & as shown on drg No. CEUZ/TD/1269/2008 Sh No 1/1 to 1/3 . Note:-(a) Fixed type glass panes shutter if any provided in above same window shall be measured and paid separately & area of these fixed shutter shall be deducted from total area of box type window for payment purpose. (b) Sheet glass/ wire cloth shall be measured & paid seperately under respective item

Factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site, complete all as specified and as directed.

Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S square tube, supplying and fixing in opening as per specification and drawing, complete all as specified and directed.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

Aluminium handles cast type anodised of size 150mm long ISI marked complete all as specified and as directed.

150mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

03 mm thick figured (frosted) glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and as directed.

03 mm thick sheet glass, ordinary quality and glazing with oil putty/wooden beads in square not exceeding 0.5 square metre in each pane complete all as specified and directed.

Galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Preparation of new steel and iron surfaces of any description over 10cm in width or girth not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) 3 layered hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete all as specified.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of bore15 mm all as specified and directed.

Mild steel galvanized steel tubing medium grade with all fittings and fixed complete to walls and ceiling or laid in floors complete of bore 20 mm all as specified and directed.

Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repairs, complete all as specified.

15mm bore Stop valve cast copper alloy screwed down high pressure with crutch or butter-fly handle, screwed both ends for iron pipes or for union, fixed in repairs, complete all as specified.

Two way bib tap with wall flange standard of brass any colour screwed for iron pipe, fixed in repairs complete all as specified and directed.

Angle/ Stop valves (Concealed type), cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions for 15mm bore pipe fixed in repairs, complete all as specified and directed.

Ball valve high pressure PTMT with epoxy coated aluminium rod & high density plastic ball 20mm dia bore, complete all as specified.

20mm bore gun metal glove or gate valve with iron wheel head screwed both end for iron pipe and fixed in repairs, complete all as specified and as directed.

PVC valve less, Symphonic action type, flushing cistern of capacity 10 liters, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete, fixed in repairs complete all as specified and as directed.

Vitreous china squatting pan "Orissa Pattern" size 580 x 440 mm in white colour with integral foot rest incl lime mortor, 'S' trap fixed in repairs complete all as specified and directed. Cat Part No-20042 (ORISSA PAN (ECO)) of Hindware or equivalent cat part of make NEYCER, CERA, PARRYWARE as approved by GE.

Supply and fixing in repairs florentine single lever surgical purpose elbow action basin mixer with extended operating lever without popup waste system with 450mm long braided hoses complete all as per Jaquar Cat Part No-FLR-5033B or equivalent cat part of make as mention in list of make P.S as approved complete all as specified and as directed.

Supply and fixing in repairs table top basin of size 170x835x455mm/ 565x425x140mm of whitecolour complete all as specified and directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 8 mm dia pipe with 1.2 meter long flexible spirochrome flex tube and ABS wall hook including making connections and fixed in repair in position complete in all respect as specified.Make-Jaquar Cat part no. ALD-573 or its equivalent cat part of make specified in list make, as approved by GE.

Plastic water closet seat cover white closed pattern with flat bottom and cover including chromium plated hinges device fixed in repairs, complete all as specified and as directed.

Vitreous china Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), with brass grating and union for discharge pipe fixed in repairs, complete all as specified.

PVC connection 15 mm size, of length 450 mm, with PTMT nuts fixed in repairs, complete all as specified and as directed.

Chromium plated brass towel rail 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls and fixed in repairs complete all as specified and as directed.

Brass chromium plated shower rose 125mm size with or without swivel joints, with arm any size, including fixing to steel pipe or union complete all as specified and directed

Glass shelf 600mm long consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing with brackets fixed in repairs all as specified and as directed. Cat part no. AKP-35771P of Jaquar or its equivalent cat part of make specified in list make, as approved by GE.

Glass corner shelf assembly consisting of 5.5 mm thick sheet with chromium plated bracket guard and railing 45 cm long complete all as specified and directed.

Taking down eaves gutters and rain water pipe , soil and waste pipe PVC or CI (any size or pattern ), includding all fittings, heads , shoes bends , swan-necks etc all as specified and directed.

110mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints laid in floors etc., complete all as specified and directed.

110mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints fixed to wall with PVC/MS holder clamp etc., complete all as specified and directed.

75mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints laid in floors etc., complete all as specified and directed.

75mm bore PVC SWR Type-B ( pressure not less than 6 kg /cm2) pipes single socket in any length with rubber ring joints fixed to wall with PVC/MS holder clamp etc., complete all as specified and directed.

PVC SWR reducer 110mm to 75 mm complete all as specified and directed.

PVC SWR Type-B cowls 75mm bore all as complete all as specified and directed.

110mm bore PVC Bends (any radius) for pvc pipes complete all as specified and directed.

PVC (SWR) bends any radius 110mm dia with oval access doors complete all as specified and directed.

110mm PVC (SWR) junction single, (single T) equal or unequal provided with access door, complete all as specified and directed.

PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

PVC (SWR) bends with access door 75mm dia complete all as specified and directed.

PVC (SWR) junction single (single T) equal or unequal 75 mm dia all as specified and directed

PVC (SWR) 75 mm dia floor trap plain with grating including jointing with solvent cement fixed in repairs, all as specified and directed.

PVC (SWR) branch piece of 110 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

PVC (SWR) branch piece of 75 bore pipe, single (single Y) equal or unequal ordinary or inverted (spigot or socket type) provided with access door complete all as specified and directed.

Supply and fix in repair only PVC waste pipe for WHB/Urinal/Sink for 32/40mm dia

Demolition of reinforced cement concrete of any description and in any position including cutting reinforcement as required to facilitate complete all as specified and directed.

Precast re-inforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed.

TMT bars, 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

Demolition of brick work or stone boulder masonary built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework, complete all as specified and as directed.

Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

PCC 1:2:4 type B-0 (Using 12.5mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out etc in any type of soil, complete all as specified and directed.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 150 mm diameter incl fittings, complete all as specified and directed.

Concrete bed to drain pipes in PCC 1:3:6 type C-2 (Using 40mm graded crushed stone aggregate) including packing under and haunching against the side of pipes after they are laid and tested for 150mm internal dia of pipe, complete all as specified and directed.

RCC class NP3 150mm dia drain pipes laid in trenches and jointed with & including coller complete all as specified and directed.

Returning filling in including spreading watering and well ramming in layers not exc 25 cm complete all as specifed .

Removing surplus soil to distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed .

Excavation in post holes each not exceeding 0.5 cum getting out in any type of soil, returning, filling in, including spreading, leveling, watering and well ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, complete all as specified.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations filling and mass concrete,complete all as specified and directed.

Supply and fixing MS galvanised coated chain link fencing n exc 4.0Kg per sqm with size of mesh 50 x 50mm and thickness of wire n.exc 3.15mm including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed. Note:-Type / size of fencing holes / dia of chain link fenching shall be as approved by GE. The weight of chain link fencing shall be calculated for payment as per actual weight or standard weight as per SSR which ever is less as approved by GE. Flat iron, nut bolts etc paid separately under respective item as supply only.

Mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc. flat iron fillets (for securing wire mesh etc). Including all necessary drilling, bolting or riveting etc. and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply only TMT bar, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

Supply only Flat iron Fe 410-W (Gde-E-250) quality-Afillet(for sequiring wire mess) including all necessery drilling,bolting & nibs etc .(Nut and bolt shall be measurd and paid saperately.

Supply only Mild steel screw bolts 11-15mm dia at neck, machine made, with hexagonal or square heads at one end and screwed the other, or screwed both ends; each screwed and to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of new or previously untreated steel surfaces of any description under 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or lying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc, (each line wire to be measured) fixed in repair complete all as specified

Concertina coil 600mm dia / 56 loops / 2.5 mm core wire, Coil Diameter: 600 mm, Type of Strip: Heavy Galvanised (IS:1703), Type of Core wire: Heavy Galvanised (IS:280-2006), Core wire Diameter: 2.50 mm Dia, Zinc Coating to Strip: Minimum 200 GSM/sqmm, Zine Coating on wire: Minimum 275 GSM/sqmm (IS 6745-1972 reaffirmed 2006), Tensile Strength of wire 1400-1500 N /sqmm, Weight: 6-8 Kg per RM (± 5%), Number of Loops: 56. Blade Length: 22 MM, Barb Profile: Medium Blade (MBBT), Distance Between Barb. 35 mm, Stretchable length 10-12 mtrs, Type of clip: Hardened Steelin Galvanised steel, complete all as specified & directed. The Concertina Coil with the said specifications shall be got approved from GE before procurement in bulk.

PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in roof kerb, padding , finished surface even and fair, complete all as specified and directed.

Dismantling timber scantlings (framed work) 40 Sqcm and over in section, in any position complete all as specified and as directed.

Dismantling asbestos cement (corrugated, semi corrugated) sheets including ridges as in roof covering, complete all as speciified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any type and any thickness including cover fillets/GI grid framework complete all as specified and directed.

Rolled mild steel structural steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastening and heavy brackets (Beam, tee, angle, channel or hollow steel section) including distance pieces, cleats etc confirming to Fe-410-W (Gde-E-250) quality B complete all as specified and as directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as ridges roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

4mm thick prelaminated designer ceiling board over & including GI snap grid frame work (Grid size 600x600mm) with powder coated GI angle of size 25x25x3mm fixed along wall perimeter, main runner 'T' of size 25x40x3mm , secondary runner 'T' of size 25x30x3mm suspended with 3mm GI wire @ 1200mm c/c of ceiling by fasteners of adjustable guide hanger including clips/MS fitments to hold the panels, complete all as specified and as directed.

Brick work with sub class B brick straight or curved on plan to any radius in half brick thick built in CM 1:4 complete all as specified and directed.

Rendering 10 mm thick in cement and sand mortar 1:4 on fair faces of brick work or cement concrete surfaces on ceiling including finishing the surface fair and even complete all as specified and directed.

15mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry wall surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Preparation of new surfaces of walls two coats of OBD over 1mm thick putty, complete all as specified and directed.

Preparation of old distempered/painted surfaces of wall including washing, rubbing down, stopping of surfaces and applying two coats of oil emulsion distemper, complete as specified and directed.

Powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Powder coated aluminium anodised door shutters(minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Supply & fixing only Door closer of aluminium (Die cast body), hydraulically regulated, designation No 3, universal type, suitable for door shutters of size 851mm to 1000mm of width , ISI marked.

Sheet glass ordinary quality, 4mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and as directed.

Powder coating Anodised aluminium window and ventilator shutters, side hung/sliding type without sash bars aluminium sections weighing 0.55 kg/m (glass & wire mess shall be measured and paid separetely) including necessary joining cleats, glazing rubber packing, anodised aluminium clips, snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 Nos.) suitable handle (1 N.) and 100 mm long aluminium tower bolt (02Nos) per shutters complete all as specified

Floor door stopper 140mm overall length of cover plate of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in bottom body of door complete all as specified and as directed.

20-25 mm thick machine cut kota stone slab as in flooring, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over with mirror cut polishing 100mm wide marble patti/border all around and including 15mm thick screed bed in cement and sand mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Note:-(Size of Kota Stone slab shall be 52 cm x 52 cm).

Description all as per item No 120 above but in skirting/dado incl 10mm thick rendering CM 1:4 complete all as specified and directed.

Vitrified ceramic tiles (Light shade) 10mm thick (square /rectangular) polished, area of each tile n.exceeding 0.36 sqm laid as in floors, set and jointed in neat cement slurry and pointed in white/coloured cement to match with shade of tiles including 15mm thick screed bed/base in cement and sand mortar 1:6, complete all as specified.

Providing cement concrete type B-1, 1:2:4 ( using 20mm graded crushed stone aggregate), 50 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair with 6mm wide joints throughout the thickness of plinth protection in concrete bays and in between the walling and plinth protection, filling the joints with mastic filling comprising of one part of heated bitumen 85/25 or 95/10 grade and 3 parts of sand ( all by weight), complete all as specified and as directed.

40mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base/ floor finishing surface even and fair, complete all as specified.

Repair to balcony/facia and soffit of chajjas etc by taking down old plastered surfaces and hacking clearly the edges and corners smooth and rounded for new plastered area exceeding 30sqcm in width or girth & applying rendering 15 mm thick dubbing coat where required to match with the existing thickness in CM 1:3 including formwork/scaffolding work upto height 7.00mtr & applying two coats of exterior emulsion weather proof paint (Apex) as reqd over one coat of primer above ground level of bldg complete all as specified and as directed.

Pressed steel frames of sizes 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates complete including one shop coat of red oxide primer, providing mild steel 6 mm dia threshold bar, all as specified and directed.

PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in door frame, complete all as specified and directed.

35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified & as directed.

35 mm thick, 2nd class hard wood, glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified and as directed.

Pre laminated particle board, exterior grade, laminated on one side with decorative choice lamination and other side balancing white lamination fixed with screw to timber frame and necessary item like hasp and staple , in repairs as cupboard/Alimirah shelve and shutter, 18/19 mm thick, complete all as specified.

Supplying & fixing of Intermat auto closing concealed hinge, complete all as specified and directed .

Supply & fixing of 6" premium quality crome finish Handle,complete as directed .

Telescopic channel set for drawer multi-tech high capacity 500 mm long as approved complete all as specified and directed .

19-20mm wide and 0.80mm thick decorative type PVC beading complete all as specified and directed.

Aluminium handle cast type anodised of size 100mm long ISI marked complete all as speicified.

Aluminium anodised sliding door bolts with hasp and stapple extruded section or cast aluminium alloy with length of bolt as 300 mm including fixing bolts complete all as specified.

300mm Mild steel ordinary rat tail helical door springs including roller and roller plate fixed, complete all as specified.

Floor door stopper 150mm length of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, complete all as specified.

Curtain rail, 20mm dia Stainless steel fixed with and including two Nos of bracket & side cup including taking down of old curtains rods, complete all as specified.

Preparation of new untreated wood and wood based surfaces of any description over 10cm in width or girth not otherwise described and painting with two coats of synthetic enamel paint over a coat of pink premier, complete all as specified.

Pillar taps 15mm cast copper alloy CP, fancy type with capstan head, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nut, screwed for iron pipe 15 mm bore.fixed in repairs, complete all as specified and as directed.

CP angle valve/concealed stop cock (weight not less than 0.40Kg cast copper alloy (ISI Marked) chromium plated fancy type screwed down high pressure with capstain head screwed both ends for iron pipe 15mm bore fixed in repairs complete all as specified and directed.

S&F in repairs kitchen utensil rack in steel made of premium grade stainless steel and highly durable and rust-proof of size not less than 90cmx80cmx20cm complete all as specified

S&F in repairs sinks with drainage board made of stainless steel (1mm thick) kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm as approved by Engr-in-Charge complete all as specified and directed.

Single lever sink mixture with popup waste system with 450 mm long braided hoses all as directed.

Chequered cement concrete tiles 300mmx300mmx 25mm thick laid & jointed with grey cement and pointed in neat cement slurry mixed with with pigment as in path/hardstanding laid over & including15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes all as specified and directed.

Disconnecting existing tanks of any description exc 1000 litres but n.exc 2000 litres capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, (after cleaning repairing, etc.), complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty and white cement at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top, bottom, side/ back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for one light point/fan /bell point controlled by one switch.:- (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers etc. are to be used of same make/brand only and shall be deemed in to included in quoted rate only.)

All as per srl item No 149 above, but One 3 pin 5 amps socket point controlled by one 5 amps switch on independent board .

All as per srl item No 149 above, but One 3 pin 5 amps socket point controlled by one 5 amps switch on same board .

Material and labour for point wiring complete with 2.5 sqmm PVC insulated, FRLS type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. metal flush box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover plate as per numbers of switch modules for modular switches,sockets,fan regulators,red colour indicator, blank plates etc as approved coloures and including 2.5 Sqmm PVC insulated multistranded FRLS type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour coat including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed for the following:- Make of Cables Havells, KEI,Grandlay (Note:- All necessary accessories such as modular steel box,top cover plate, blank plate, screws,washers etc. are to be used of same make/brand only and shall be deemed in to included in quoted rate only.) for One 15 amps power socket outlet point controlled by one 16 amps switch on independent board.

Modular type switch 10 Amps, single pole,1way,1/2 module,240V, ISI Marked complete all as specified and directed.

Modular type switch 16 Amps, single pole, 1way,1 module, 240V, ISI Marked Complete all as specified and directed. Make- Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”.

Modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module, 240V, AC ISI Marked Complete all as specified and directed. Make- Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”.

Modular type socket 6 A/16 Amps, 2/3 Pin combined shuttered socket 2 module with light indication ,240V,AC ISI Marked Complete all as specified and directed . Make- Crabtree (Havells) or its equivalent in Anchor (Roma), Legrand, Seimens as approved”.

Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed

LED light fitting General purpose surface and wall mounted LED batten with Aluminium housing integrated electronic driver, 10W 2 feet and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed. Cat Part No-BS10WLED865 SPCSS of Havells or its equivalent of Bajaj, Crompton, Orient as approved by GE.

LED light fitting General purpose surface and wall mounted LED batten with Aluminium housing integrated electronic driver, 20W 4 feet and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed. Cat Part No-BS20WLED 830 SPCSS of Havells or its equivalent of Bajaj, Crompton, Orient as approved by GE.

LED INVERTER batten with square profile and poly carbonate channel lithium ion battery with charging time 8 to 10 hours and backup time upto 4 hours and connecting up with twin core twisted copper wire from LED fitting to ceiling rose and removing old unserviceable fitting complete all as specified and directed. Make :- Pride plus inverter batten 4 feet, 20W 6500K of Havells or equivalent in Bajaj, Surya, Wipro as approved by GE.

LED bulb 12 watts, 240Volts,50Hz pin type and including removing old unserviceable item complete all as specified and directed. Cat Part No-LHLDEUEEML8R012 Havells or its equivalent in Bajaj, Surya as approved.

Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 08 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, including blanking plates where required. , complete all as specified. Make:-Havells cat part No-DHDPSHODPW08 or Equivalent cat part of make of Legrand / Indoasian / L&T

MCB SP 6 to 32 Amps 10 KA,"C" series,AC,240Volts,50Hz , ISI marked fixed in repairs complete all as specified and directed. Make:- Legrand cat No.4085 87 to 4085 95 / Hager Cat Ref No.NCN106N to NCN132N / Havells Cat No.DHMGCSPF006-032 as approved

MCB SPN 32 to 40 Amps 10 KA,"C" series,AC,240Volts,50Hz, ISI marked fixed in repairs complete all as specified and directed.Make:- Legrand cat No.4086 17 to 4086 18/ Hager cat part No:- NCN232N /Havells cat part No.DHMGCSNF040 / L&T cat part NoBB20400C as approved

Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron and light grade protection pipe of 40 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh, including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45cm x 45cm x 45 cm,RCC cover 1:2:4 type B1 of size 45x45x6 cm, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed. Note:- The required resistance of Earthing shall be less than 3 ohm, If not found to the required resisstance, the contractor has to re earthing for required resistance and the cost for the same included in the quoted rate and no extra shall be paid on failure of getting required resistance.

Exhaust fan single phase metal body, AC 230 Volt, 50 Hz, 1200 RPM of size 250mm sweep with louvers shutter complete with all accessories including connecting up from ceiling rose complete all as specified and directed. Make:- Cat part No:- Turbo Force 1P Grey of Havells or its Equivalent cat part of make-BAJAJ,CROMPTON GREAVES, GEC, KHAITAN,ORIENT as approved by GE

Sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade,FRLS type, PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit of size 25 mm dia medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 2.5 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade,FRLS type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface including cutting and cheasing and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 2.5 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

PVC insulated stranded aluminium conductor (XLPE) served with an inner sheathing of PVC tape, PVC sheathed armoured with galvanized steel wire of type (heavy duty) under ground electric cable 1100 volt grade of cross sections area of 16 Sqmm 2 core

Supply and laying sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Sand cushioning in trenches including spreading and consolidation in layers of 8cm thick before laying the cable & 15 cm thick after laying the cable and punned down to form a bed complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be recorded for payment putpose.

Supply and fixing in replacement “Lithium based Energy Efficient Integrated Solar Street Light of 25Watt” in Single FRP body with duly Polyurethane coating (Camouflage color) , encases with Monocrystalline Solar PV Panel of 53/55Wp , Lithium Battery 11.1/12.8V, 28.6AH with inbuilt BMS, IP 65, High brightness W-LED(160-180lm/watt) lamp with Aluminum reflector for better light distribution , CRI >70, Color Temperature 5700K - 6500K, Microcontroller based charge controller cum driver, automatic dimming function ( first four hours at full brightness & rest of the time at lower light level with PIR Motion Sensor), Dusk to Dawn Operation, suitable to working temperature: (-) 10C to (+)55C, weight not more than 12-14kg with adjustable MS clamp suitable for pole/wall mounting etc complete as required. Protections: Short Circuit, overload, Reverse polarity and battery protections. Firm should provide Vital Parameters Test report from NABL accredited lab and should be of made in India with CE & ROHS compliant. CAT part No ENXT P 25L WH PO PC SD of Bajaj or equivalent cat part of Make in phillips / Surya / Havells/Crompton/Orient

Taking down old unserviceable Exhaust fan of any type/size from existing location and deposit in MES store yard and Supply and fix exhaust fan single phase metal body, AC 230 Volt, 50 Hz of size 300mm sweep with louvers shouter complete with all accessories including connecting up from ceiling rose to motor all as specified and directed. "Cat part No refresh air SPS of Havells standard or its equivalent, Bajaj, Orient".

Ceiling fans complete with blades, down rods, and accessories, 230 volt, 1200mm sweep, min air delivery 210 CFM with service value 6 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make:- Cat Part No Zinger of Make Havells or its Equivalent cat part of make as specified in list of make here- in after. Note : Items declared BER vide convening order No 4000/CO/BPs/465/E4 dated 21 May 2022 already deposited with MES/ E&M yard.

Fan regulator modular type electronic, stepped type 100 Watts, 2 module 240Volts, AC ISI marked complete all as specified and directed. “Cat part No ACVRFHW008 of Crabtree (Havells) or its equivalent cat part of make make Anchor, Legrand, Schneider as approved by GE”.

Electric water heater storage type, capacity 25 litres and heating element 2KW, BEE 5 Star rated complete with all accessories such as a safety valve, thermostate, NRV, connection pipes of GI/PVC and necessary electric connections etc including taking down existing and depositing in MES. Make : Crompton/Havells/Bajaj as approved.

Supply and fixing of Double wall corrugated (DWC) HDPE tubing 50 mm bore for open/underground laying cable, cut to size and making the tubing for cable protection including cutting of road etc/cutting of PCC and making the good surface complete all as specified and directed by Engr-in-Charge. (a) The using of GI Clamp in the wall/drainage rate are deemed to be included in the quoted rate. (b) The insulation of DWC pipe should be of high that does not deteriorate with UV rays/ heavy sun rays/winter season etc. (c) Drawing existing cable through DWC pipe shall be deemed to be included in the quoted rates

Supply and laying pipe galvanised Medium Class including fittings 25mm (1.0) dia all as specified and directed.

Cutting the existing 50mm tubing and inserting new GI Tee of size 50 x 50 x 25mm dia and including necessary screwing threading, tail pieces, short pieces, jointing material etc complete all as specified and directed.

25 mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed high pressure with crutch or butterfly handle fixed in repairs complete all as specified and as directed.

M/s Rajesh Kumar Contractor (BID ID -3127655)

M/S KARAN SINGH CONTRACTOR (BID ID -3128637)

M/S JEEVAN LAL SHARMA (BID ID -3128220)