Upgradation Repair whitewash aluminium partation of building, chain link fencing at bain Bajalta for make shift accomodation of GDC Sidhra and Construction of Bathroom (under UT Capex).

Providing and fixing partition upto ceiling height consisting of G.I. frame andrequired board, including providing and fixing of frame work made of specialsection power pressed/ roll form G.I. sheet with zinc coating of 120gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mmwide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor andceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mmdiameter 50 mm length or suitable anchor fastener or metal screws with nylonplugs and the studs 48 mm wide having one flange of 34 mm and other flange36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia boltsand nuts, including fixing of studs along both ends of partition fixed flush towall with suitable anchor fastener or metal screws with nylon plugs at spacingof 450 mm centre to centre, and fixing of boards to both side of framework by25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work withjoints staggered to avoid through cracks, M.S. fixing channel of 99 mm width(0.9 mm thick having two flanges of 9.5 mm each) to be provided at thehorizontal joints of two boards, fixed to the studs using metal to metal flat headscrews, including jointing and finishing to a flush finish with recommendedjointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5mm), joint finisher and two coats of primer suitable for board as permanufacture’s specification and direction of engineer in charge all complete.75mm overall thickness partitions with 12.5 thick double skin fire rated Glass Reinforced Gypsum (GRG), plaster board confirming to IS : 2095 (Part 3) 1996 (Board with BIS Certification marks).

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns. 60mm × 40mm × 2mm.

Aluminium work for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns) 80 mm × 30 mm × 1.8 mm.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width

Providing and fixing aluminium tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. Complete 150x10 mm

Providing and fixing aluminium handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100 mm

Providing and fixing double action hydraulic floor spring of approvedbrand and manufacture IS : 6315 marked, having brand logo embossedon the body/plate with double spring mechanism and door weight upto125 kg for doors including cost of cutting floors, embedding in floors asrequired and making good the same matching to the existing floorfinishing and cover plates with brass pivot and single piece M.S. sheetouter box with slide plate etc. complete as per the direction of Engineerin-plate etc. complete as per the direction of Engineer-in-charge.22.4.1 With Stainless Steel cover plate minimum 1.25 mm thickness.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work