COMPREHENSIVE REPAIR OF MAP ACCN AT ALWAR MIL STN

Amount

Taking down cement plaster of any description on walls, including raking out joints, hacking for key, scrubbing down with water, etc including removal of derbis upto 1.0 Km from the site complete all as specified & directed.

M&L rendering 15mm thick,plaster on fair faces of brick work or stone masonry or concrete surfaces in CM 1:4 including finished surfaces even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) all as specified.

M&L rendering 10mm thick,plaster on other than of fair faces of brick work or stone masonry or concrete surfaces in CM 1:6 including finished surfaces fair and even complete all as specifed and directed.

M & L 5mm thick rendering in cement mortor 1:3 on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete.

Dismantling of old app membrane on roof surfaces in cluding removal of loose old plaster for receiving new plastering complete.

M&L screed laid 15mm thick in CM 1:4 with water proofing compound over concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) .

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete .

S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm . It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming IS:[email protected]/sqm and Two coats of aluminium paint over APP membrane surface complete.

M&L for providing and injecting chemical emulsion for post constructional anti termite treatment alongwith the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear meter incl drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors drilling and plugging holes etc all as specified and directed

M&L preparing new surfaces of walls, plastered and applying two coat of cement base paint over a coat of white wash on walls including cornices, pillasteres complete all as specified & as directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer on walls complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling/soffits of chajjas complete all as specified and directed by Engineer-in-Charge.

M&L for demolition of concrete (unrreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to location outside defence land complete all as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish off the premises complete all as specified and directed

Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L brick work with fly ash bricks ,straight or curved on plan exc 6m mean radius, old size bricks in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick built in cement mortar 1:4

M&L cement concrete 75mm thick 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified & directed.

M&L for rubber moulded concrete coloured tiles with grey cement and pigment of size 300mmx300x22-25 mm thick laid over and including 20 mm thick cement mortar screed bed in CM 1:6 as in floors complete all as specified & directed.

M&L for 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) as in bedding layer of floor finished the surface even and rough complete all as specified and directed.

M&L for Non Skid white ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6, Complete .Make:Johnson,Kajaria,AGL.

All as per item No.23 above but in skirting over and including 10 mm thick plaster in cement mortar 1:4 including necessary cutting of tiles as required size all as specified and as directed.

M&L for coloured Non skid ceramic tiles(Ist quality) 7 to 8mm thick area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in floors etc., laid over and including 15 mm thick screed bed of cement & sand mortar 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.Make:Johnson,kajaria,AGL

M&L Glazed ceramic coloured tiles(Ist quality) in vertical surface 450x300 x 7-8 mm thick joint free set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in Cement& Sand Mortar 1:4 complete all as specified and directed.Make:Johnson,kajaria,AGL

Hacking out old broken glass of any thickness/size & any description from wooden or steel frame fixed with clips/putty/wooden beading and S&F with 3mm thick ordinary sheet glass fixed with clips and oil putty/wooden beading completed in squares not exc 0.50 Sqm each pane all as specified and as directed.

-do- as per item No 27 above but 3mm thick figured glass, pin head type.

S&F in repairs galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm and fixed tinned tacks or GI wire stampe or nails and screws/wooden beading complete all as specified & directed.

S&F in repairs MS dropery rod 25 mm dia fancy type with PVC coloured sleeves fixed with suitable brackets two Nos & PVC colour bowl two Nos at end for door/window compleete all as directed by Engr-in-charge.

S&F in repairs SS Curtain rod 25 mm dia as including suitable fancy type brackets and Knob fixed with rawl plug, screw etc complete all as specified.

S&F in repairs 300 mm size MS ,ordinary rat tail rod pattern springs including roller and roller plate complete frames with Screws/welding as required at site complete all as specified.

S&F in repairs 300 mm long aluminium alloy anodised sliding door bolt with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section of cast aluminium and fixed all as spd.

S&F in repairs Extruded aluminium alloy handle, fabricated type, anodised, 125mm size, (ISI marked) complete all as specified.

S&F as in repairs 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified

Supply and fixing in repairs butt hinges 100 mm long medium weight cold rolled MS fixed in repairs to wooden or pressed steel/angle iron frames by welding all as specified.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed overall length 140 mm complete all as specified & directed.

Supply and fixing in repairs MS steel window stay 300 mm long for steel windows all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs handles for steel windows all as specified and directed by Engineer-in-Charge.

Taking down shutter of any description not exc 1 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws all as directed.

Taking up or down steel tubing and connections,bore of pipe 15mm complete all as directed.

S&F for 15mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store bore of pipe 20mm complete all as directed.

S&F for 20mm dia steel water tubing medium grade galvanised with all fittings and fixed to wall and ceiling or laid in floor complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 500 Ltrs hoisted and fixed in position with ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed of 20mm dia, minimum weight - 210 gms all as specified in SSR Part I including dismantaling existing water tanks complete all as specified and directed.

S&F in repairs ball valves of 20mm dia, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed, minimum weight - 210 gms of including taking down existing ball valves any type all as directed by Engr-in-Charge. Make : Prayag or equivalent .

S&F (in repairs) vitreous china wash down water closet pan(Pedestal Type) white (ISI marked), including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonoage pipe etc & with plastic WC seat cover (white) closed pattern with flat bottom and cover and suitable mild steel chromium plated or aluminised hinging device complete all as specified. (Make : Hindware/Cera as approved by GE).

S&F (in repairs) vitreous china squatting pan 'orissa pattern' size 580 x 450 mm white with integral foot rest (ISI marked) with 'P' or 'S' trap, front or back inlet and foot rest any pattern, including connection to flushing pipe anti-syphonage pipe etc, including setting of pan & trap in lean PCC 1:5:10 complete and making good to distrubed floor with PCC or cement mortar 1:3 to match with sorroundings all as directed.

S&F in repairs vitreous china wash basin white of size 550x400 mm with padestal stand (ISI marked) including 32 mm CP waste coupling & PVC flexible waste pipe of min 90 cm long, flat back or angle back type excluding taps, waste chain & plug but incuding cast iron brackets and cutting for and pinning in ends of brackets or erecting stand complete fixed in repairs all as specified and directed.

S&F in repairs Jet spray PVC butterfly plated for EWC with & including PVC connection 600 mm long suitable for 15 mm bore GI pipe with PTMT nut & nipple complete.

S&F in repairs health fusset chromium plated suitable for 15 mm bore pipe including 1 M long PVC tubes for EWC complete all as specified & directed by Engineer-in-Charge.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, complete all as specified.

S&F in repairs for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as directed.

S&F in repairs for PVC internal fittings (kit) complete for low level flushing cistern tank, all as specified and directed by Engineer-in-Charge. Make Commander/Perryware.

S&F in repairs for towel rails of 20mm dia tubular brass chromium plated 60cm long 'D' type fixed to all as directed by Engr-in-charge including taking down existing towel rail.

S&F in repairs waste coupling 32mm of PTMT (half or full threaded) (minimum wt 45 gms complete all as specified & directed.

S&F in repairs plastic water closet seat cover white /coloured closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified an directed.

Supply and replacement in repairs of brass spindles, phases of brass of any size required 3/4/5 for bib taps, pillar cocks, stop cocks, angle valves, concealed valves complete all as directed.

S&F in repairs for CP grating 75/100mm dia, with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed.

S&F in repairs 15 mm bore pillar taps, Cast Copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly nuts, screwed for iron pipe etc complete as specified and directed.

S&F in repairs Brass chromium plated shower rose with long arm 150mm size fixed to 15mm bore pipe all as directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete.

S&F in repairs waste coupling for sink as per sample approved comjplete all as directed.

S&F in repairs mirror cabinet (PTMT) fixed on wall with cadmium plated brass screws as per approved by GE all as directed.

S&F in repairs bib taps bore of pipe in 15mm, cast copper alloy, fancy type, chromium plated, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. (Make : Prayag/Cera/Marc).

S&F in repairs for bib tap standard of PTMT any colour 15mm bore high pressure screwed for iron pipe (Min. wt 90 gms) and complete all as specified and directed. (Make : Prayag/Poly tuff).

S&F in repairs 15mm bore, stop valve/angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repairs 15mm bore, two way angle valve, chromium plated, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in reapirs, 15mm bore, stop valve external threaded, chromium plated, fancy type, with long shank, and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions etc complete all as specified and directed.

S&F in repairs 20 mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified & directed

S&F in repairs PVC flexable waste pipe 32/40 mm dia & approx 900 mm long with PVC waste coupling suitable for WHB, sink & urinal complete all as specified & directed.

S&F in repairs Brass CP Wall mixer for mixing hot & cold water suitable for 15mm bore dia pipe screwed down for iron pipe and fixed copmplete all as specified and directed.

Dismantling AC Pipe/ PVC pipes 110mm/ 75 mm dia

S&F 110mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, fixed to walls with MS clamps as per site requirement complete all as directed.

S&F PVC(SWR) Vent cowl 75mm dia complete all as directed.

S&F 75mm dia PVC (SWR) pipes single sockets, in any length with rubber ring joints, laid in trenches or floors complete all as directed.

All as per item No 78 here in before but fixed to walls with clamps complete all as directed.

S&F PVC (SWR) bends 75mm dia any radius complete all as directed.

S&F PVC (SWR) 75mm dia Floor Trap, plain with grating including jointing with solvent cement all as directed.

Running welding in repairs not exceeding 6mm thick all as specified and directed

Welding in repairs not exceeding 6mm thick and not exceeding 2.5 cm in length all as specified and directed

Taking down Chowkats or frames with shutters ( without taking off shutters from the frame) n exc 1.5 sq.each & removing to store.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified& directed

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

Taking down Shutters of any description exc 1 sq. m but n exc 2 sqm each & removing to store.

Taking down Chowkats or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.Fe-410 (Gde-E250 quality A).

S&F 35mm thick IInd class hard wood factory made panelled door shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified& directed

S&F 35 mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed

S&F Butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified& directed

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed

S&F 150mm Aluminium handles, cast type, anodised complete all as specified & directed

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed

Treatement for sunken portion is as follows :- (i) Demolition of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. (ii) M&L for providing 12 mm dia holes of 40mm deep @2.00m c/c at junction of beams and columns as co-ordinal points for inserting/pouring cement slurry by pressure grouting for sunken floors of toilet , includind sealing the holes with CM 1:3, all as specified and as directed by Engineer - in - Charge. (iii) M&L for water proofing plaster for sunken portion in CM 1:3, 20 mm thick in two coats with water proofing compound at the rate of 2% by weight of cement and finishing the surface even and smooth without using extra cement. (WPC will be measured and paid seperately). (iv) M&L for applyin evenly two coats of industrial bitumen 85/25 at the rate of 1.20 Kg/Sqm in each coat over vertical surfaces and floors of sunken floors of toilet including cleaning of surfaces. (v) M&L for PCC 1:7:12 type D2 using 40 mm graded stone aggregate as in filling (sunken portion). etc. (vi) M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate, mixed with WPC @ 2% by wt. of cement, as sub base, 75mm thick. (WPC will be measured and paid separately.) on top (vii) M&L for plastering in CM 1:4, 15 mm thick with water proofing compound at the rate of 2% by weight of cement and finishing the surface seven and fair.(WPC will be measured and paid seperately) Note :- Above includes (a) Test again of water tightness by pounding for 72 hours & rectify defects if any till total elimination of defect. (b) The sunken portion shall be tested for leakage / seepage / dampness by pounding with water for 72 hours. In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. The process of grouting and testing shall be repeated till leakage / seepage / dampness is eliminated. (c) Horizontal flat area to be measered.

M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165

M&L machine cut kota stone slab flooring 18-19mm thick over 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified& directed

Mirror polishing on marble/ granite/Kota stone/ stone work where ever required to give high gloss finish complete.

M&L for Granite (of any type) tiles 18-20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete

Taking down carefully copper/aluminium point wiring of any size (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

Taking down MCB with sheet metal enclosure, main switch, DB etc and making good disturbed surfaces to match with existing surfaces.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surfaces

Taking down carefully by unscrewing from boards /outlet boxes fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittigs, bulk head fittings tube lights etc complete all as specified and directed by Eng-in-charge

M&L for concealed Point wiring in repair with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws tith washer complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. One Light point controlled by one, one way switch.

M&L for concealed Point wiring in repair with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws tith washer complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. One 3 pin switch socket outlet, 5 Amp on the same board with other switches.

M&L for concealed Point wiring in repair with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws tith washer complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. One 3 pin 5 amps switch socket outlet point on independent board.

M&L for concealed Point wiring in repair with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws tith washer complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. One bell/buzzer point controlled by one bell push.

M&L for concealed Point wiring in repair with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws tith washer complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. Two way point controlled by two way switch.

All as per item Sl. No. 108 here in before but wiring with 4.0 sq.mm multistranded cable and earth wire with copper conductor of size 4.0 sq.mm for 15 amps power/geyser point.

M&L for concealed Point wiring in repair with single core PVC insulated, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in existing conduit including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with 3 mm thick bakelite plastic laminated sheet top cover with brass counter shunk screws with washerc complete all as specified. Note - quoted rate shall include making good to the disturbed surfaces including plastering and painting to match with the existing colour. One ceiling/exhaust fan point controlled by one switch and regulator

S&F in repair Piano type switch single pole 1 way 5/6 amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge.

S&F in repair Piano type switch single pole 2 way 15/6 amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge.

S&F in repair Piano type switch single pole 1 way 15/16 amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge.

S&F in repair Ding Dong Bell along with bell push flush type 5 amps complete all as specified and directed by Engr-in-Charge.

S&F in repair socket two in one 6/5 Pin 5 Amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge.

S&F in repair socket two in one 6/5 Pin 15/16 Amps 230 volt AC supply complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair following switches, piano type, 230/250 volts grade on top covers (catered in point wiring above) :- Modular switch, one way 6 Amp, 1 module

Supply and fixing in repair following switches, piano type, 230/250 volts grade on top covers (catered in point wiring above) :- Modular switch, two way 6 Amp, 1 module

Supply and fixing in repair following switches, piano type, 230/250 volts grade on top covers (catered in point wiring above) :- Modular switch, one way 16 Amp, 1 module

Supply and fixing in repair following switches, piano type, 230/250 volts grade on top covers (catered in point wiring above) :- Modular bell push 6 Amp, 1 module

Supply and fix in repair socket out let multipurpose use, flush mounting type, 230/250 Volts grade on Top covers (catered in point wiring above) :- Modular socket outlet 2in1, 3pin 5A, 2 module

Supply and fix in repair socket out let multipurpose use, flush mounting type, 230/250 Volts grade on Top covers (catered in point wiring above) :- Modular socket outlet 2in1, 3 pin 15 Amps flush type

S&F in repair PVC white cover plate with frame 2 Module etc complete all as specified & directed.

S&F in repair PVC white cover plate with frame 3 Module etc complete all as specified & directed.

S&F in repair PVC white cover plate with frame 4 Module etc complete all as specified & directed.

S&F in repair PVC white cover plate with frame 6 Module. etc complete all as specified & directed.

S&F in repair PVC white cover plate with frame 8 Module etc complete all as specified & directed.

S&F in repair modular metal flush box 2 Module etc complete all as specified & directed.

S&F in repair modular metal flush box 3 Module etc complete all as specified & directed.

S&F in repair modular metal flush box 4 Module etc complete all as specified & directed.

S&F in repair modular metal flush box 6 Module. etc complete all as specified & directed.

S&F in repair modular metal flush box 8 Module etc complete all as specified & directed.

Supply and fixing in repair decorative ultra slim, elegant and sleek designed LED T5 batten lighting fixture with extruded aluminium housing with frosted diffuser enviornment friendly energy efficient suitable for 20 watt LED tube light with 125 lumen per watt complete all as specified and dircted

Supply and fix in repair Lamp holder, PVC/Polycarbonate type complete with lamp LED 9 Watt for Batten fitting with back plate and all fittings complete all as specified and directed by Engr-In-Charge

Supplly and fixing in repair indoor decorative ultra slim surface/ wall mounted T5 LED batten tube light complete fitting 1 x 9 watt LED tiube fitting (size within 600 x 25 x 40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver, energy efficient, 140V-270 volts, co-related colour temperature (CCT) of 6500K> 100Lm/WATT complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make : Havells, Philips, Bajaj

Supply and fix in repair ceiling rose surface bakelite two to three terminals/plate, polycarbonate, isolated body.

Supply and fix in repair sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door.

Supply and fix in repair Switch socket combination 2 in 1, 5 A flush type inc taking down old onecomplete all as specified and as directed.

Supply and fix in repair Switch socket combination 5A/16A, 5 in 1 inc taking down old one complete all as specified and as directed.

Supply and fix in repair Switch socket combination 2 in 1, 5 A, 3 Pin with modular box flush type inc taking down old one complete all as specified and as directed.

Supply and fix in repair Switch socket combination 5A/16A, 5 in 1 with modular box inc taking down old one complete all as specified and as directed.

Supply and fixing in repair 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-In-Charge SP 6-32 Amp

Supply and fixing in repair 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed by Engr-In-Charge SPN 63 Amp

Supply and fix in repair Vertical DB 4 way suitable for Double Pole outgoing MCB-40 Amp-04 Nos with incoming 100 Amps MCCB 4 pole-01 Nos complete with 250 Amps rated Copper busbar flush mounting, double door, proction class IP-30, IK08 complete all as specified.

Supply and fix in repair MCCB 100 Amps, 4 pole, 16 KA thermal and magnetic release in V TPN DB complete all as specified.

Supply and fixing in repair PVC Blanking Plates one way with internal lock complete.

S & F in repair stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed by Engr in charge.

S & F in repair modular fan regulator, 120W-2 Module complete all as specified and directed by Engr in charge.

Material & Labour for Sub Main Wiring in repair with two run single core 4 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 2.5 Sqmm copper green colour earth wire all as specified and directed by Engr-in-Charge. NOTE-two run of 4 sq.mm & One run of 2.5 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

Material & Labour for Sub Main Wiring in repair with two run single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 4 Sqmm copper green colour earth wire all as specified and directed by Engr-in-Charge. NOTE-two run of 6 sq.mm & One run of 4 sq.mm & One run of PVC conduit with accessories shall be measured as One length.

M & L for Earthing in repair complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick burried directly in ground earth pit not less than 2.25 Mtr deep below normal ground level with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, checknuts and washers of galvanised iron all as shown in electrical plate No 5 of SSR Part-I, connected to transformer / feeder pillar all as specified including GI pipe 20 mm bore medium grade for watering and 15 mm GI Pipe light grade for protection of earth lead wire, PCC chamber using PCC 1:3:6 type C-2 CI frame and cover, funnel and wiremesh, all excavation and earth work etc complete all as specified and directed by Engr-in-Charge

Supply and fixing in repair LED light fitting as building security lights of 35 Watt Cap 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover, incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer, with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr-In-Charge

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric poer cable (heavy duty) 1100 conductor of size 25 Sq mm 4.0 core.

Excavation in trenches not exc 1.5 m wide and n. exc 1.5 m deep in soft/loose soil for foundation/ cable etc n exc 10 Sqm on plan and n exc 1.5 Sqm in depth all as specified and directed by Engr-in-Charge

Returning, filling in including spreading levelling, watering and well ramming in layer n. exc 25 cm thick complete all as specified and directed

Removing surplus soil to a distance n. exc 50 m and depositing where directed at level n. exc 1.5 m above the starting point complete all as specified and directed

Supply and spreading, levelling river sand in trenches for cables cushioning on top and bottom of cable all as specifede and directed.

M&L brick protection with sub class'B' brick laid flat across the cable complete all as specified and directed

M&L for boring under roads for crossing of UG Cables complete all as specifie and directed by Engr-In-Charge.

Supply and fix GI Pipe light grade of size 40 mm laid in trenches under road/fixed on wall/pole for cable protection complete all as specified and directed by Engr-In-Charge

M/S JINDAL ENTERPRISES (BID ID -3339506)